Driver shouldn't allow to use UMR to register a MR when
umr_modify_atomic_disabled is set. Otherwise it will always end up with a
failure in the post send flow which sets the UMR WQE to modify atomic access
right.
Fixes: c8d75a980f ("IB/mlx5: Respect new UMR capabilities")
Signed-off-by: Guy Levi <guyle@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20190731081929.32559-1-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
The specification for the Toeplitz function doesn't require to set the key
explicitly to be symmetric. In case a symmetric functionality is required
a symmetric key can be simply used.
Wrongly forcing the algorithm to symmetric causes the wrong packet
distribution and a performance degradation.
Link: https://lore.kernel.org/r/20190723065733.4899-7-leon@kernel.org
Cc: <stable@vger.kernel.org> # 4.7
Fixes: 28d6137008 ("IB/mlx5: Add RSS QP support")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Alex Vainman <alexv@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
The device requires that memory registration work requests that update the
address translation table of a MR will be fenced if posted together. This
scenario can happen when address ranges are invalidated by the mmu in
separate concurrent calls to the invalidation callback.
We prefer to block concurrent address updates for a single MR over fencing
since making the decision if a WQE needs fencing will be more expensive
and fencing all WQEs is a too radical choice.
Further, it isn't clear that this code can even run safely concurrently,
so a lock is a safer choice.
Fixes: b4cfe447d4 ("IB/mlx5: Implement on demand paging by adding support for MMU notifiers")
Link: https://lore.kernel.org/r/20190723065733.4899-8-leon@kernel.org
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Any dma map underlying the MR should only be freed once the MR is fenced
at the hardware.
As of the above we first destroy the MKEY and just after that can safely
call to dma_unmap_single().
Link: https://lore.kernel.org/r/20190723065733.4899-6-leon@kernel.org
Cc: <stable@vger.kernel.org> # 4.3
Fixes: 8a187ee52b ("IB/mlx5: Support the new memory registration API")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix unreg_umr to move the MR to a kernel owned PD (i.e. the UMR PD) which
can't be accessed by userspace.
This ensures that nothing can continue to access the MR once it has been
placed in the kernels cache for reuse.
MRs in the cache continue to have their HW state, including DMA tables,
present. Even though the MR has been invalidated, changing the PD provides
an additional layer of protection against use of the MR.
Link: https://lore.kernel.org/r/20190723065733.4899-5-leon@kernel.org
Cc: <stable@vger.kernel.org> # 3.10
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Use a direct firmware command to destroy the mkey in case the unreg UMR
operation has failed.
This prevents a case that a mkey will leak out from the cache post a
failure to be destroyed by a UMR WR.
In case the MR cache limit didn't reach a call to add another entry to the
cache instead of the destroyed one is issued.
In addition, replaced a warn message to WARN_ON() as this flow is fatal
and can't happen unless some bug around.
Link: https://lore.kernel.org/r/20190723065733.4899-4-leon@kernel.org
Cc: <stable@vger.kernel.org> # 4.10
Fixes: 49780d42df ("IB/mlx5: Expose MR cache for mlx5_ib")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Fix unreg_umr to ignore the mkey state and do not fail if was freed. This
prevents a case that a user space application already changed the mkey
state to free and then the UMR operation will fail leaving the mkey in an
inappropriate state.
Link: https://lore.kernel.org/r/20190723065733.4899-3-leon@kernel.org
Cc: <stable@vger.kernel.org> # 3.19
Fixes: 968e78dd96 ("IB/mlx5: Enhance UMR support to allow partial page table update")
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Memory allocated by kvzalloc should not be freed by kfree(), use kvfree()
instead.
Fixes: 813e90b1ae ("IB/mlx5: Add advise_mr() support")
Link: https://lore.kernel.org/r/20190717082101.14196-1-hslester96@gmail.com
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Enable RDMA DIM by default for better user experience.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Userspace expects the IB_TM_CAP_RC bit to indicate that the device
supports RC transport tag matching with rendezvous offload. However the
firmware splits this into two capabilities for eager and rendezvous tag
matching.
Only if the FW supports both modes should userspace be told the tag
matching capability is available.
Cc: <stable@vger.kernel.org> # 4.13
Fixes: eb76189435 ("IB/mlx5: Fill XRQ capabilities")
Signed-off-by: Danit Goldberg <danitg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Max Gurtovoy says:
====================
Those two patches introduce VHCA tunnel mechanism to DEVX interface
needed for Bluefield SOC. See extensive commit messages for more
information.
====================
Based on the mlx5-next branch from
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux for
dependencies
* branch 'vcha-tunnel':
IB/mlx5: Implement VHCA tunnel mechanism in DEVX
net/mlx5: Introduce VHCA tunnel device capability
This mechanism will allow function-A to perform operations "on behalf" of
function-B via tunnel object. Function-A will have privileges for creating
and using this tunnel object.
For example, in the device emulation feature presented in Bluefield-1 SoC,
using device emulation capability, one can present NVMe function to the
host OS.
Since the NVMe function doesn't have a normal command interface to the HCA
HW, here is a need to create a channel that will be able to issue commands
"on behalf" of this function.
This channel is the VHCA_TUNNEL general object. The emulation software
will create this tunnel for every managed function and issue commands via
devx general cmd interface using the appropriate tunnel ID. When devX
context will receive a command with non-zero vhca_tunnel_id, it will pass
the command as-is down to the HCA.
All the validation, security and resource tracking of the commands and the
created tunneled objects is in the responsibility of the HCA FW. When a
VHCA_TUNNEL object destroyed, the device will issue an internal
FLR (function level reset) to the emulated function associated with this
tunnel. This will destroy all the created resources using the tunnel
mechanism.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for ib callback counter_alloc_stats() and
counter_update_stats().
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add support for ib callbacks counter_bind_qp(), counter_unbind_qp() and
counter_dealloc().
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add counter set id as a parameter so that this API can be used for
querying any q counter.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Support bind a qp with counter. If counter is null then bind the qp to the
default counter. Different QP state has different operation:
- RESET: Set the counter field so that it will take effective during
RST2INIT change;
- RTS: Issue an RTS2RTS change to update the QP counter;
- Other: Set the counter field and mark the counter_pending flag, when QP
is moved to RTS state and this flag is set, then issue an RTS2RTS
modification to update the counter.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in the next patches.
* mlx5-next:
net/mlx5: Add rts2rts_qp_counters_set_id field in hca cap
net/mlx5: Properly name the generic WQE control field
net/mlx5: Introduce TLS TX offload hardware bits and structures
net/mlx5: Refactor mlx5_esw_query_functions for modularity
net/mlx5: E-Switch prepare functions change handler to be modular
net/mlx5: Introduce and use mlx5_eswitch_get_total_vports()
There is no need in custom memory zeroing, because it can be done
by using kzalloc from the beginning.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
No need any more to hold mlx5_core_dev on the devx_object, it can be
accessed from ib_dev.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Add DEVX support for CQ events by creating and destroying the CQ via
mlx5_core and set an handler to manage its completions.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Implement DEVX dispatching event by looking up for the applicable
subscriptions for the reported event and using their target fd to
signal/set the event.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Enable subscription for device events over DEVX.
Each subscription is added to the two level xarray data structure
according to its event number and the DEVX object information in case was
given with the given target fd.
Those events will be reported over the given fd once will occur.
Downstream patches will mange the dispatching to any subscription.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Register DEVX with with mlx5_core to get async events. This will enable
to dispatch the applicable events to its consumers in down stream patches.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Introduce MLX5_IB_OBJECT_DEVX_ASYNC_EVENT_FD and its initial
implementation.
This object is from type class FD and will be used to read DEVX
async events.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Instead MLX5_TOTAL_VPORTS, use mlx5_eswitch_get_total_vports().
mlx5_eswitch_get_total_vports() in subsequent patch accounts for SF
vports as well.
Expanding MLX5_TOTAL_VPORTS macro would require exposing SF internals to
more generic vport.h header file. Such exposure is not desired.
Hence a mlx5_eswitch_get_total_vports() is introduced.
Given that mlx5_eswitch_get_total_vports() API wants to work on const
mlx5_core_dev*, change its helper functions also to accept const *dev.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
From git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in the next patches.
Resolved the conflicts:
- esw_destroy_offloads_acl_tables() use the newer mlx5_esw_for_all_vports()
version
- esw_offloads_steering_init() drop the cap test
- esw_offloads_init() drop the extra function arguments
* branch 'mlx5-next': (39 commits)
net/mlx5: Expose device definitions for object events
net/mlx5: Report EQE data upon CQ completion
net/mlx5: Report a CQ error event only when a handler was set
net/mlx5: mlx5_core_create_cq() enhancements
net/mlx5: Expose the API to register for ANY event
net/mlx5: Use event mask based on device capabilities
net/mlx5: Fix mlx5_core_destroy_cq() error flow
net/mlx5: E-Switch, Handle UC address change in switchdev mode
net/mlx5: E-Switch, Consider host PF for inline mode and vlan pop
net/mlx5: E-Switch, Use iterator for vlan and min-inline setups
net/mlx5: E-Switch, Reg/unreg function changed event at correct stage
net/mlx5: E-Switch, Consolidate eswitch function number of VFs
net/mlx5: E-Switch, Refactor eswitch SR-IOV interface
net/mlx5: Handle host PF vport mac/guid for ECPF
net/mlx5: E-Switch, Use correct flags when configuring vlan
net/mlx5: Reduce dependency on enabled_vfs counter and num_vfs
net/mlx5: Don't handle VF func change if host PF is disabled
net/mlx5: Limit scope of mlx5_get_next_phys_dev() to PCI PF devices
net/mlx5: Move pci status reg access mutex to mlx5_pci_init
net/mlx5: Rename mlx5_pci_dev_type to mlx5_coredev_type
...
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently during dual port IB device registration in below code flow,
ib_register_device()
ib_device_register_sysfs()
ib_setup_port_attrs()
add_port()
get_counter_table()
get_perf_mad()
process_mad()
mlx5_ib_process_mad()
mlx5_ib_process_mad() fails on 2nd port when both the ports are not fully
setup at the device level (because 2nd port is unaffiliated).
As a result, get_perf_mad() registers different PMA counter group for 1st
and 2nd port, namely pma_counter_ext and pma_counter. However both ports
have the same capability and counter offsets.
Due to this when counters are read by the user via sysfs in below code
flow, counters are queried from wrong location from the device mainly from
PPCNT instead of VPORT counters.
show_pma_counter()
get_perf_mad()
process_mad()
mlx5_ib_process_mad()
process_pma_cmd()
This shows all zero counters for 2nd port.
To overcome this, process_pma_cmd() is invoked, and when unaffiliated port
is not yet setup during device registration phase, make the query on the
first port. while at it, only process_pma_cmd() needs to work on the
native port number and underlying mdev, so shift the get, put calls to
where its needed inside process_pma_cmd().
Fixes: 212f2a87b7 ("IB/mlx5: Route MADs for dual port RoCE")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Report EQE data upon CQ completion to let upper layers use this data.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Enhance mlx5_core_create_cq() to get the command out buffer from the
callers to let them use the output.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Use the reported device capabilities for the supported user events (i.e.
affiliated and un-affiliated) to set the EQ mask.
As the event mask can be up to 256 defined by 4 entries of u64 change
the applicable code to work accordingly.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Devlink eswitch mode is not necessarily related to SR-IOV, e.g, ECPF
can be at offload mode when SR-IOV is not enabled.
Rename the interface and eswitch mode names to decouple from SR-IOV,
and cleanup eswitch messages accordingly.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an IB rep is loaded, netdev for the same vport is saved for later
reference. However, it's not cleaned up when doing unload. For ECPF,
kernel crashes when driver is referring to the already removed netdev.
Following steps lead to a shown call trace:
1. Create n VFs from host PF
2. Distroy the VFs
3. Run "rdma link" from ARM
Call trace:
mlx5_ib_get_netdev+0x9c/0xe8 [mlx5_ib]
mlx5_query_port_roce+0x268/0x558 [mlx5_ib]
mlx5_ib_rep_query_port+0x14/0x34 [mlx5_ib]
ib_query_port+0x9c/0xfc [ib_core]
fill_port_info+0x74/0x28c [ib_core]
nldev_port_get_doit+0x1a8/0x1e8 [ib_core]
rdma_nl_rcv_msg+0x16c/0x1c0 [ib_core]
rdma_nl_rcv+0xe8/0x144 [ib_core]
netlink_unicast+0x184/0x214
netlink_sendmsg+0x288/0x354
sock_sendmsg+0x18/0x2c
__sys_sendto+0xbc/0x138
__arm64_sys_sendto+0x28/0x34
el0_svc_common+0xb0/0x100
el0_svc_handler+0x6c/0x84
el0_svc+0x8/0xc
Cleanup the rep and netdev reference when unloading IB rep.
Fixes: 26628e2d58 ("RDMA/mlx5: Move to single device multiport ports in switchdev mode")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the single IB device mode, the mapping between vport number and
rep relies on a counter. However for dynamic vport allocation, it is
desired to keep consistent map of eswitch vport and IB port.
Hence, simplify code to remove the free running counter and instead
use the available vport index during load/unload sequence from the
eswitch.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Suggested-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Os1seHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGtx4H/j6i482XzcGFKTBm
A7mBoQpy+kLtoUov4EtBAR62OuwI8rsahW9di37QKndPoQrczWaKBmr3De6LCdPe
v3pl3O6wBbvH5ru+qBPFX9PdNbDvimEChh7LHxmMxNQq3M+AjZAZVJyfpoiFnx35
Fbge+LZaH/k8HMwZmkMr5t9Mpkip715qKg2o9Bua6dkH0AqlcpLlC8d9a+HIVw/z
aAsyGSU8jRwhoAOJsE9bJf0acQ/pZSqmFp0rDKqeFTSDMsbDRKLGq/dgv4nW0RiW
s7xqsjb/rdcvirRj3rv9+lcTVkOtEqwk0PVdL9WOf7g4iYrb3SOIZh8ZyViaDSeH
VTS5zps=
=huBY
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc6' into rdma.git for-next
For dependencies in next patches.
Resolve conflicts:
- Use uverbs_get_cleared_udata() with new cq allocation flow
- Continue to delete nes despite SPDX conflict
- Resolve list appends in mlx5_command_str()
- Use u16 for vport_rule stuff
- Resolve list appends in struct ib_client
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
If vport metadata matching is enabled in eswitch, the rule created
must be changed to match on the metadata, instead of source port.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor the flow data structures, add new flow_context and move
flow_tag into it, as flow_tag doesn't belong to the rule action.
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The lock protecting the data structure does not need to be an rwlock. The
only read access to the lock is in an error path, and if that's limiting
your scalability, you have bigger performance problems.
Eliminate mlx5_mkey_table in favour of using the xarray directly.
reg_mr_callback must use GFP_ATOMIC for allocating XArray nodes as it may
be called in interrupt context.
This also fixes a minor bug where SRCU locking was being used on the radix
tree read side, when RCU was needed too.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Improve code readability using static helpers for each memory region
type. Re-use the common logic to get smaller functions that are easy
to maintain and reduce code duplication.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
If possibe, avoid doing a UMR operation to register data and protection
buffers (via MTT/KLM mkeys). Instead, use the local DMA key and map the
SG lists using PA access. This is safe, since the internal key for data
and protection never exposed to the remote server (only signature key
might be exposed). If PA mappings are not possible, perform mapping
using MTT/KLM descriptors.
The setup of the tested benchmark (using iSER ULP):
- 2 servers with 24 cores (1 initiator and 1 target)
- ConnectX-4/ConnectX-5 adapters
- 24 target sessions with 1 LUN each
- ramdisk backstore
- PI active
Performance results running fio (24 jobs, 128 iodepth) using
write_generate=1 and read_verify=1 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1266.4K/1262.4K 1720.1K/1732.1K
4k 793139/570902 1129.6K/773982
32k 72660/72086 97229/96164
Using write_generate=0 and read_verify=0 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1590.2K/1600.1K 1828.2K/1830.3K
4k 1078.1K/937272 1142.1K/815304
32k 77012/77369 98125/97435
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Suggested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
In some loads, there is performance degradation when using KLM mkey
instead of MTT mkey. This is because KLM descriptor access is via
indirection that might require more HW resources and cycles.
Using KLM descriptor is not necessary when there are no gaps at the
data/metadata sg lists. As an optimization, use MTT mkey whenever it
is possible. For that matter, allocate internal MTT mkey and choose the
effective pi_mr for in transaction according to the required mapping
scheme.
The setup of the tested benchmark (using iSER ULP):
- 2 servers with 24 cores (1 initiator and 1 target)
- ConnectX-4/ConnectX-5 adapters
- 24 target sessions with 1 LUN each
- ramdisk backstore
- PI active
Performance results running fio (24 jobs, 128 iodepth) using
write_generate=1 and read_verify=1 (w/w.o/baseline):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1262.4K/1243.3K/1147.1K 1732.1K/1725.1K/1423.8K
4k 570902/571233/457874 773982/743293/642080
32k 72086/72388/71933 96164/71789/93249
Using write_generate=0 and read_verify=0 (w/w.o patch):
bs IOPS(read) IOPS(write)
---- ---------- ----------
512 1600.1K/1572.1K/1393.3K 1830.3K/1823.5K/1557.2K
4k 937272/921992/762934 815304/753772/646071
32k 77369/75052/72058 97435/73180/94612
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Suggested-by: Max Gurtovoy <maxg@mellanox.com>
Suggested-by: Idan Burstein <idanb@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
IB_WR_REG_SIG_MR is not needed after IB_WR_REG_MR_INTEGRITY
was used.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Protect the case that a ULP tries to allocate a QP with signature
enabled flag while the LLD doesn't support this feature.
While we're here, also move integrity_en attribute from mlx5_qp to
ib_qp as a preparation for adding new integrity API to the rw-API
(that is part of ib_core module).
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Rename IB_QP_CREATE_SIGNATURE_EN to IB_QP_CREATE_INTEGRITY_EN
and IB_DEVICE_SIGNATURE_HANDOVER to IB_DEVICE_INTEGRITY_HANDOVER.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This new WR will be used to perform PI (protection information) handover
using the new API. Using the new API, the user will post a single WR that
will internally perform all the needed actions to complete PI operation.
This new WR will use a memory region that was allocated as
IB_MR_TYPE_INTEGRITY and was mapped using ib_map_mr_sg_pi to perform the
registration. In the old API, in order to perform a signature handover
operation, each ULP should perform the following:
1. Map and register the data buffers.
2. Map and register the protection buffers.
3. Post a special reg WR to configure the signature handover operation
layout.
4. Invalidate the signature memory key.
5. Invalidate protection buffers memory key.
6. Invalidate data buffers memory key.
In the new API, the mapping of both data and protection buffers is
performed using a single call to ib_map_mr_sg_pi function. Also the
registration of the buffers and the configuration of the signature
operation layout is done by a single new work request called
IB_WR_REG_MR_INTEGRITY.
This patch implements this operation for mlx5 devices that are capable to
offload data integrity generation/validation while performing the actual
buffer transfer.
This patch will not remove the old signature API that is used by the iSER
initiator and target drivers. This will be done in the future.
In the internal implementation, for each IB_WR_REG_MR_INTEGRITY work
request, we are using a single UMR operation to register both data and
protection buffers using KLM's.
Afterwards, another UMR operation will describe the strided block format.
These will be followed by 2 SET_PSV operations to set the memory/wire
domains initial signature parameters passed by the user.
In the end of the whole transaction, only the signature memory key
(the one that exposed for the RDMA operation) will be invalidated.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Explicitly pass the sig_mr and the access flags for the mkey segment
configuration. This function will be used also in the new signature
API, so modify it in order to use it in both APIs. This is a preparation
commit before adding new signature API.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
UMR ctrl segment flags can vary between UMR operations. for example,
using inline UMR or adding free/not-free checks for a memory key.
This is a preparation commit before adding new signature API that
will not need not-free checks for the internal memory key during the
UMR operation.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
PI offload (protection information) is a feature that each RDMA provider
can implement differently. Thus, introduce new device attribute to define
the maximal length of the page list for PI fast registration operation. For
example, mlx5 driver uses a single internal MR to map both data and
protection SGL's, so it's equal to max_fast_reg_page_list_len / 2.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
mlx5_ib_map_mr_sg_pi() will map the PI and data dma mapped SG lists to the
mlx5 memory region prior to the registration operation. In the new
API, the mlx5 driver will allocate an internal memory region for the
UMR operation to register both PI and data SG lists. The internal MR
will use KLM mode in order to map 2 (possibly non-contiguous/non-align)
SG lists using 1 memory key. In the new API, each ULP will use 1 memory
region for the signature operation (instead of 3 in the old API). This
memory region will have a key that will be exposed to remote server to
perform RDMA operation. The internal memory key that will map the SG lists
will stay private.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Update ib_umem_release() to behave similarly to kfree() and allow
submitting NULL pointer as safe input to this function.
Fixes: a52c8e2469 ("RDMA: Clean destroy CQ in drivers do not return errors")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
