pm_runtime_get_sync() increments the runtime PM usage counter even
the call returns an error code. Thus a pairing decrement is needed
on the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124649.10848-1-dinghao.liu@zju.edu.cn
There are two error handling paths in this functon. When
wlcore_tx_work_locked() returns an error code, we should
decrease the runtime PM usage counter the same way as the
error handling path beginning from pm_runtime_get_sync().
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520124241.9931-1-dinghao.liu@zju.edu.cn
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43legacy did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43legacy will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-3-Larry.Finger@lwfinger.net
Since the driver was first introduced into the kernel, it has only
handled the ciphers associated with WEP, WPA, and WPA2. It fails with
WPA3 even though mac80211 can handle those additional ciphers in software,
b43 did not report that it could handle them. By setting MFP_CAPABLE using
ieee80211_set_hw(), the problem is fixed.
With this change, b43 will handle the ciphers it knows in hardware,
and let mac80211 handle the others in software. It is not necessary to
use the module parameter NOHWCRYPT to turn hardware encryption off.
Although this change essentially eliminates that module parameter,
I am choosing to keep it for cases where the hardware is broken,
and software encryption is required for all ciphers.
Reported-and-tested-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200526155909.5807-2-Larry.Finger@lwfinger.net
This reverts commit 07d0f55349.
For rtw88 driver, the SDIO is going to be supported, so there is
no need to remove the SDIO related power sequence settings. And
while the power sequence parser will pass in the mask of the HCI,
the SDIO part will not be used to set registers accordingly.
Moreover, the power sequence table is released as a whole package,
so the next time if we are going to update, the SDIO settings will
be overwritten. So, revert this now.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520055350.23328-1-yhchuang@realtek.com
I am leaving Quantenna, so I will no longer have access to firmware and
hardware. Meanwhile I plan to participate in reviewing qtnfmac patches
for a while until my firmware knowledge becomes completely obsolete.
Adding myself as a reviewer using my personal email address.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200520130800.1902-1-sergey.matyukevich.os@quantenna.com
This gives us WPA3 support out of the box without having to manually disable
hardware crypto. The driver will fall back to software crypto if the connection
requires management frame protection.
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200525134906.1672-1-rsalvaterra@gmail.com
change typo in function name "nofity" to "notify"
sctp_ulpevent_nofity_peer_addr_change ->
sctp_ulpevent_notify_peer_addr_change
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a field to the tls rx offload context which enables
drivers to force a send_resync call.
This field can be used by drivers to request a resync at the next
possible tls record. It is beneficial for hardware that provides the
resync sequence number asynchronously. In such cases, the packet that
triggered the resync does not contain the information required for a
resync. Instead, the driver requests resync for all the following
TLS record until the asynchronous notification with the resync request
TCP sequence arrives.
A following series for mlx5e ConnectX-6DX TLS RX offload support will
use this mechanism.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
net_sched: reduce the number of qdisc resets
This patchset aims to reduce the number of qdisc resets during
qdisc tear down. Patch 1~3 are preparation for their following
patches, especially patch 2 and patch 3 add a few tracepoints
so that we can observe the whole lifetime of qdisc's. Patch 4
and patch 5 are the ones do the actual work. Please find more
details in each patch description.
Vaclav Zindulka tested this patchset and his large ruleset with
over 13k qdiscs defined got from 22s to 520ms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting old qdisc on dev_queue->qdisc_sleeping in
dev_qdisc_reset() is redundant, because this qdisc,
even if not same with dev_queue->qdisc, is reset via
qdisc_put() right after calling dev_graft_qdisc() when
hitting refcnt 0.
This is very easy to observe with qdisc_reset() tracepoint
and stack traces.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Tested-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for sch_mq and sch_mqprio, each dev queue points to the
same root qdisc, so when we reset the dev queues with
netdev_for_each_tx_queue() we end up resetting the same instance
of the root qdisc for multiple times.
Avoid this by checking the __QDISC_STATE_DEACTIVATED bit in
each iteration, so for sch_mq/sch_mqprio, we still reset all
of them like before, for the rest, we only reset it once.
Reported-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Tested-by: Václav Zindulka <vaclav.zindulka@tlapnet.cz>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qdisc_destroy() calls ops->reset() and cleans up qdisc->gso_skb
and qdisc->skb_bad_txq, these are nearly same with qdisc_reset(),
so just call it directly, and cosolidate the code for the next
patch.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No element named "client" exists within "struct ipa_endpoint".
It might be a heritage forgotten to be removed. Delete it now.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "transactio" -> "transaction". Also an alignment correction.
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: tcp_v4_err() cleanups
This series is a followup of patch 239174945d ("tcp: tcp_v4_err() icmp
skb is named icmp_skb").
Move the RFC 6069 code into a helper, and rename icmp_skb to standard
skb name so that tcp_v4_err() and tcp_v6_err() are using consistent names.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This essentially reverts 4d1a2d9ec1 ("Revert Backoff [v3]:
Rename skb to icmp_skb in tcp_v4_err()")
Now we have tcp_ld_RTO_revert() helper, we can use the usual
name for sk_buff parameter, so that tcp_v4_err() and
tcp_v6_err() use similar names.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 6069 logic has been implemented for IPv4 only so far,
right in the middle of tcp_v4_err() and was error prone.
Move this code to one helper, to make tcp_v4_err() more
readable and to eventually expand RFC 6069 to IPv6 in
the future.
Also perform sock_owned_by_user() check a bit sooner.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Tested-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: misc updates for -next
This patchset includes some misc updates for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing CMDQ fails because of reset pending,
there is no hint for debugging, so adds a log for it.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets will not pass through MAC during app loopback.
Therefore, it is meaningless to enable MAC while doing
app loopback. This patch removes this unnecessary action.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The HNS RDMA driver will support VF device later, whose
re-initialization should be done after PF's. This patch
changes the order of hclge_reset_prepare_up() and
hclge_notify_roce_client(), so that PF's RoCE client
will be reinitialized before VF's.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prevent from initializing VF NIC client in reset handling state,
this patch adds resetting check in hclgevf_init_nic_client_instance().
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antoine Tenart says:
====================
net: mscc: allow forwarding ioctl operations to attached PHYs
These two patches allow forwarding ioctl to the PHY MII implementation,
and support is added for offloading timestamping operations to
compatible attached PHYs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for offloading timestamping operations not only
to the Ocelot switch (as already supported) but to compatible PHYs.
When both the PHY and the Ocelot switch support timestamping operations,
the PHY implementation is chosen as the timestamp will happen closer to
the medium.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ioctl to be implemented by the PHY, when a PHY is attached to the
Ocelot switch. In case the ioctl is a request to set or get the hardware
timestamp, use the Ocelot switch implementation for now.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple large ecmp group nexthop selftests to cover
the remnant fixed by d69100b8ee.
The tests create 100 x32 ecmp groups of ipv4 and ipv6 and then
dump them. On kernels without the fix, they will fail due
to data remnant during the dump.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_PM, the compiler warns about two unused functions:
drivers/net/ethernet/mediatek/mtk_star_emac.c:1472:12: error: unused function 'mtk_star_suspend' [-Werror,-Wunused-function]
drivers/net/ethernet/mediatek/mtk_star_emac.c:1488:12: error: unused function 'mtk_star_resume' [-Werror,-Wunused-function]
Mark these as __maybe_unused.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the MRP netlink interface. Before, each attribute
represented a binary structure which made it hard to be extended.
Therefore update the MRP netlink interface such that each existing
attribute to be a nested attribute which contains the fields of the
binary structures.
In this way the MRP netlink interface can be extended without breaking
the backwards compatibility. It is also using strict checking for
attributes under the MRP top attribute.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable new_pvid is being assigned with a value that is never read,
the following if statement updates new_pvid with a new value in both
of the if paths. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_addr field in desc_data must not be overwritten until after the
new skb is mapped. Currently we do replace it with uninitialized value
in error path. This change fixes it by moving the assignment before the
label to which we jump after mapping or allocation errors.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer br_dev is being initialized with a value that is never read
and is being updated with a new value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
net/ipv4/nexthop.c:841:30: warning: implicit conversion from enumeration
type 'enum nexthop_event_type' to different enumeration type 'enum
fib_event_type' [-Wenum-conversion]
call_nexthop_notifiers(net, NEXTHOP_EVENT_DEL, nh);
~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~
1 warning generated.
Use the right type for event_type so that clang does not warn.
Fixes: 8590ceedb7 ("nexthop: add support for notifiers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1038
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Atheros 100Base-T PHYs. The only difference seems to be
the ability to test 2 pairs instead of 4 and the lack of 1000Base-T
specific register.
Only the ATH9331 was tested with this patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
Raw PHY TDR data
Some ethernet PHYs allow access to raw TDR data in addition to summary
diagnostics information. Add support for retrieving this data via
netlink ethtool. The basic structure in the core is the same as for
normal phy diagnostics, the PHY driver simply uses different helpers
to fill the netlink message with different data.
There is a graphical tool under development, as well a ethtool(1)
which can dump the data as text and JSON.
A patched ethtool(1) can be found in
https://github.com/lunn/ethtool.git feature/cable-test-v5
Thanks for Chris Healy for lots of testing.
v2:
See the individual patches but:
Pass distances in centimeters, not meters
Allow the PHY to round distances to what it supports and report what
it actually used along with the results.
Make the Marvell PHY use steps a multiple of 0.805 meters, its native
step size.
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Unsquash the last two patches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Getting the TDR data requires a large number of MDIO bus
transactions. The number can however be reduced if the page is only
changed once. Add the needed locking to allow this, and make use of
unlocked read/write methods where needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.
If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHYs can measure the amplitude of the returned signal for
a given distance. Implement this option of the cable test
infrastructure. When reporting the step, convert the distance into cm.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
Step based on the measurement resolution, and convert this to cm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2
Update nxp-tja11xx for API change.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHYs can return the raw time domain reflectromatry data.
Add the attributes to allow this data to be requested and returned via
netlink ethtool.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
m -> cm
Report what the PHY actually used for start/stop/step.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a ton of minor checkpatch errors/warnings and remove version
printing at module init/when device is found and use MODULE_VERSION
instead. Also modifying the RTL8029 PCI string to include the compatible
RTL8029AS nic.
The only mayor issue remaining is the missing SPDX tag, but since the
exact version of the GPL is not stated anywhere inside the file, its
impossible to add such a tag at the moment.
But maybe it is possible, since 8390.h states Donald Becker's 8390
drivers are licensed under GPL 2.2 only (= GPL-2.0-only ?).
The kernel module containing this patch compiles and runs without
problems on a RTL8029AS-based NE2000 clone card with kernel 5.7.0-rc6.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
