For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.
For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.
Improve code readability by removing this redundant code.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit 0a764db103 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit 0a764db103 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing a bitwise AND between a bool and an int is generally not a good idea.
The bool will be promoted to an int with value 0 or 1,
the int is generally regarded as true with a non-zero value,
thus ANDing them has the potential to yield an undesired result.
This commit fixes the following smatch warnings:
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:344 enh_desc_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:337 dwmac4_rd_prepare_tx_desc() warn: maybe use && instead of &
drivers/net/ethernet/stmicro/stmmac/dwmac4_descs.c:380 dwmac4_rd_prepare_tso_tx_desc() warn: maybe use && instead of &
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom tags inserted by Broadcom switches put a 4 byte header after
the MAC SA and before the EtherType, which may look like some sort of 0
length LLC/SNAP packet (tcpdump and wireshark do think that way). With
ACS enabled in stmmac the packets were truncated to 8 bytes on
reception, whereas clearing this bit allowed normal reception to occur.
In order to make that possible, we need to pass a net_device argument to
the different core_init() functions and we are dependent on the Broadcom
tagger padding packets correctly (which it now does). To be as little
invasive as possible, this is only done for gmac1000 when the network
device is DSA-enabled (netdev_uses_dsa() returns true).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).
Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).
SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5
The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).
Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
public S805 datasheet the only supported parent clock is MPLL2 (this
was not verified using the oscilloscope).
The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
by 1", etc.) for the input clock. we call this clock the "m250_div"
clock because it's value is always supposed to be (close to) 250MHz
(see below for an explanation).
The description in the public S805/S905 datasheet is a bit cryptic,
but it comes down to "input clock = 250MHz * value" (which could also
be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
output from the m250_div and divides it by 2. This is not unusual on
Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
divide-by-2 clock.
This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
clock (which is an output on the MAC/SoC and an input in the PHY). we
call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
TX clock output is close to 0
The description for this bit in the public S805/S905 datasheet is
"Generate 25MHz clock for PHY". Based on these tests it's believed
that this is wrong, and should probably read "Generate the 125MHz
RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
output (automatically) depending on the line speed (RGMII specifies
that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
100Mbit/s were tested with an oscilloscope). Due to the requirement
that this clock always has to be set to 125MHz and due to the fixed
divide-by-2 parent clock this means that m250_div will always end up
with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
of Amlogic's older GPL kernel sources.
The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.
This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).
Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.
While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note in the databook - Section 4.4 - EEE :
" The EEE feature is not supported when the MAC is configured to use the
TBI, RTBI, SMII, RMII or SGMII single PHY interface. Even if the MAC
supports multiple PHY interfaces, you should activate the EEE mode only
when the MAC is operating with GMII, MII, or RGMII interface."
Applying this restriction solves a stability issue observed on Amlogic
gxl platforms operating with RMII interface and the internal PHY.
Fixes: 83bf79b6bb ("stmmac: disable at run-time the EEE if not supported")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason not to allow printing the frame_len/COE value and put
that under a check for ETH_FRAME_LEN, drop it so we can see what the
descriptor reports.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the printing of the ring number consistent and properly aligned by
padding the ring number with up to 3 zeroes, which covers the maximum
ring size. This makes it a lot easier to see outliers in debug prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in dwmac4_wrback_get_rx_timestamp_status the timestamp is found
in the context descriptor following the current descriptor. However the
current code looks for the context descriptor in the current
descriptor, which will always fail.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GMAC4 the value written in PTP_SSIR should be shifted however
the shifted value is also used in subsequent calculations which results
in a bad timestamp value.
Signed-off-by: Fredrik Hallenberg <megahallon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing that says that number of TX queues == number of RX
queues. E.g. the ARTPEC-6 SoC has 2 TX queues and 1 RX queue.
This code is obviously wrong:
for (chan = 0; chan < tx_channel_count; chan++) {
struct stmmac_rx_queue *rx_q = &priv->rx_queue[chan];
priv->rx_queue has size MTL_MAX_RX_QUEUES, so this will send an
uninitialized napi_struct to __napi_schedule(), causing us to
crash in net_rx_action(), because napi_struct->poll is zero.
[12846.759880] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[12846.768014] pgd = (ptrval)
[12846.770742] [00000000] *pgd=39ec7831, *pte=00000000, *ppte=00000000
[12846.777023] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[12846.782942] Modules linked in:
[12846.785998] CPU: 0 PID: 161 Comm: dropbear Not tainted 4.15.0-rc2-00285-gf5fb5f2f39a7 #36
[12846.794177] Hardware name: Axis ARTPEC-6 Platform
[12846.798879] task: (ptrval) task.stack: (ptrval)
[12846.803407] PC is at 0x0
[12846.805942] LR is at net_rx_action+0x274/0x43c
[12846.810383] pc : [<00000000>] lr : [<80bff064>] psr: 200e0113
[12846.816648] sp : b90d9ae8 ip : b90d9ae8 fp : b90d9b44
[12846.821871] r10: 00000008 r9 : 0013250e r8 : 00000100
[12846.827094] r7 : 0000012c r6 : 00000000 r5 : 00000001 r4 : bac84900
[12846.833619] r3 : 00000000 r2 : b90d9b08 r1 : 00000000 r0 : bac84900
Since each DMA channel can be used for rx and tx simultaneously,
the current code should probably be rewritten so that napi_struct is
embedded in a new struct stmmac_channel.
That way, stmmac_poll() can call stmmac_tx_clean() on just the tx queue
where we got the IRQ, instead of looping through all tx queues.
This is also how the xgbe driver does it (another driver for this IP).
Fixes: c22a3f48ef ("net: stmmac: adding multiple napi mechanism")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mss variable tracks the last max segment size sent to the TSO
engine. We do not update the hardware as long as we receive skb:s with
the same value in gso_size.
During a network device down/up cycle (mapped to stmmac_release() and
stmmac_open() callbacks) we issue a reset to the hardware and it
forgets the setting for mss. However we did not zero out our mss
variable so the next transmission of a gso packet happens with an
undefined hardware setting.
This triggers a hang in the TSO engine and eventuelly the netdev
watchdog will bark.
Fixes: f748be531d ("stmmac: support new GMAC4")
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver expect "allwinner,leds-active-low" to be in PHY node, but
the binding doc expect it to be in MAC node.
Since all board DT use it also in MAC node, the driver need to search
allwinner,leds-active-low in MAC node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
The LPI transitioning logic in stmmac_main uses
priv->tx_path_in_lpi_mode to enter/exit LPI.
However, priv->tx_path_in_lpi_mode is assigned
using the return value from host_irq_status().
So for dwmac4, priv->tx_path_in_lpi_mode was always false,
so stmmac_tx_clean() would always try to put us in eee mode,
and stmmac_xmit() would never take us out of eee mode.
To fix this, make host_irq_status() read and return the LPI
irq status also for dwmac4.
This also increments the existing LPI counters, so that
ethtool --statistics shows LPI transitions also for dwmac4.
For dwmac1000, irqs are enabled/disabled using the register
named "Interrupt Mask Register", and thus setting a bit disables
that specific irq.
For dwmac4 the matching register is named "MAC_Interrupt_Enable",
and thus setting a bit enables that specific irq.
Looking at dwmac1000_core.c, the irqs that are always enabled are:
LPI and PMT.
Looking at dwmac4_core.c, the irqs that are always enabled are:
PMT.
To be able to read the LPI irq status, we need to enable the LPI
irq also for dwmac4.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Hopefully this is the last batch of networking fixes for 4.14
Fingers crossed...
1) Fix stmmac to use the proper sized OF property read, from Bhadram
Varka.
2) Fix use after free in net scheduler tc action code, from Cong
Wang.
3) Fix SKB control block mangling in tcp_make_synack().
4) Use proper locking in fib_dump_info(), from Florian Westphal.
5) Fix IPG encodings in systemport driver, from Florian Fainelli.
6) Fix division by zero in NV TCP congestion control module, from
Konstantin Khlebnikov.
7) Fix use after free in nf_reject_ipv4, from Tejaswi Tanikella"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: systemport: Correct IPG length settings
tcp: do not mangle skb->cb[] in tcp_make_synack()
fib: fib_dump_info can no longer use __in_dev_get_rtnl
stmmac: use of_property_read_u32 instead of read_u8
net_sched: hold netns refcnt for each action
net_sched: acquire RTNL in tc_action_net_exit()
net: vrf: correct FRA_L3MDEV encode type
tcp_nv: fix division by zero in tcpnv_acked()
netfilter: nf_reject_ipv4: Fix use-after-free in send_reset
netfilter: nft_set_hash: disable fast_ops for 2-len keys
Numbers in DT are stored in “cells” which are 32-bits
in size. of_property_read_u8 does not work properly
because of endianness problem.
This causes it to always return 0 with little-endian
architectures.
Fix it by using of_property_read_u32() OF API.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently stmmac driver not copying the valid ethernet
MAC address to MAC registers. This patch takes care
of updating the MAC register with MAC address.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to DWMAC databook the first queue operating mode
must always be in DCB.
As MTL_QUEUE_DCB = 1, we need to always set the first queue
operating mode to DCB otherwise driver will think that queue
is in AVB mode (because MTL_QUEUE_AVB = 0).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to DT bindings documentation we are expecting a
property called "snps,read-requests" but we are parsing
instead a property called "read,read-requests".
This is clearly a typo. Fix it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore compatibles about dwmac-sun8i
This reverts commit ad4540cc5a ("net: stmmac: sun8i: Remove the compatibles")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner H3 SoC have two distinct MDIO bus, only one could be
active at the same time.
The selection of the active MDIO bus are done via some bits in the EMAC
register of the system controller.
This patch implement this MDIO switch via a custom MDIO-mux.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Since these compatible is automatically registered, dwmac-sun8i compatible
does not need to be in need_mdio_ids.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the possible reason for different hard to reproduce
problems on my ARMv7-SMP test system.
The symptoms are in recent kernels imprecise external aborts,
and in older kernels various kinds of network stalls and
unexpected page allocation failures.
My testing indicates that the trouble started between v4.5 and v4.6
and prevails up to v4.14.
Using the dirty_tx before acquiring the spin lock is clearly
wrong and was first introduced with v4.6.
Fixes: e3ad57c967 ("stmmac: review RX/TX ring management")
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent infinite loop by correctly setting the loop condition to
break when i == 10.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GMAC4 the valid timestamp is from CTX next desc but
we are passing the previous desc to get_rx_timestamp_status()
callback.
Fix this and while at it rework a little bit the function logic.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX HW timestamp is enabled and a frame is discarded we are
not freeing the skb but instead only setting to NULL the entry.
Add a call to dev_kfree_skb_any() so that skb entry is correctly
freed.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control must be disabled for AVB enabled queues and TX
AVB queues must be enabled by setting BIT(2) of TXQEN.
Correct this by passing the queue mode to DMA callbacks
and by checking in these functions wether we are in AVB
performing the necessary adjustments.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are using all the available fifo size in RQS and
TQS fields. This will not work correctly in multi-queues IP's
because total fifo size must be splitted to the enabled queues.
Correct this by computing the available fifo size per queue and
setting the right value in TQS and RQS fields.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA reset timeout, used in read_poll_timeout, is
ten times shorter than the sleep time.
This patch fixes these values interchanging them, as it was
before the read_poll_timeout introduction.
Fixes: 8a70aeca80 ("net: stmmac: Use readl_poll_timeout")
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many macros in dwmac-ipq806x are unused and should be removed.
Moreover gmac->id is an unsigned variable and therefore checking
whether it is less than zero is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-enable the MAC receiver by setting CONFIG_RE before powering down,
as instructed in section 6.3.5.1 of [1]. Without this the MAC fails
to receive WoL packets and never wakes up.
[1] DWC Ethernet QoS Databook 4.10a October 2014
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hook to stmmac_pltfr_pm_ops for suspend / resume handling.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
