If we do use regmap then regmap will take care of things for us. We
actually already have this check at a higher level for the current
users but this makes sure we do the right thing in the future too if
we need to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently not all DAPM widget IO ops are holding their component mutex
(codec or platform). Make sure this is now held for DAPM widget IO operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove printk(KERN_WARNING) and use dev_warn() instead.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent enhancements in the bias management means that we might not be
in standby when the CODEC is idle and can have active widgets without
being in full power mode but the shutdown functionality assumes these
things. Add checks for the bias level at each stage so that we don't
do transitions other than the ON->PREPARE->STANDBY->OFF ones that the
drivers are expecting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This means we don't need to walk through every single widget in the system
for each stream event which is a bit less silly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do smarter things with DAI links create DAPM
widgets which directly represent the DAIs in the DAPM graph. These are
automatically created from the DAIs as we probe the card with references
held in both directions between the widget and the DAI.
The widgets are not made available for direct instantiation by drivers,
they are created automatically from the DAIs. Drivers should be updated
to create stream routes using DAPM maps rather than by annotating AIF
and DAC widgets with streams.
In order to ease transition to this model from existing drivers we
automatically create DAPM routes between the DAI widgets and the existing
stream widgets which are started and stopped by the DAI widgets, though
the old stream handling mechanism is still in place. This also has the
nice effect of removing non-DAPM devices as any device with a DAI
acquires a widget automatically which will allow future simplifications
to the core DAPM logic.
The intention is that in future the AIF and DAI widgets will gain the
ability to interact such that we are able to manage activity on
individual channels independantly rather than powering up and down the
entire AIF as we do currently.
Currently we only generate these for CODECs, mostly as I have no systems
with non-CODEC DAPM to integrate with. It should be a simple matter of
programming to add the additional hookup for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do something smarter than iterate through widgets
doing strcmp() to work out what to power up for stream events change the
interface used to generate them to be based on the combination of a DAI
and a stream direction rather than just a simple string identifying the
stream.
At some point we'll probably want a set of channels too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Let the caller fiddle with the widget after we're done in order to
facilitate further refactoring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Everything now uses snd_soc_dapm_new_controls() instead so we don't need
to make it part of the external API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since the addition of the non-CODEC control adds card controls like the
DAPM pin switch have been broken as they are expecting the private data
for the control to be the CODEC but it's now the card. Fix that for the
pin switches, an audit of other drivers is required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently when DAPM widgets are power sequenced the stream_event()
completion callback is only called for the stream_event originator
DAPM context. Other components in the card may also be interested so
make sure they are also notified of any widget power events.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's useful to export the DAPM reset as a static function for future use
by other DAPM functions. e.g. The dynamic PCM query widgets resets the DAPM
graph before working out active paths.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix some spelling mistakes in the header and remove the todo items. Most
todo items are now available as kcontrol options now anyway.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow for the operation of custom mixer and mux DAPM widgets that can call
snd_soc_dapm_mixer_update_power() and snd_soc_dapm_mux_update_power() directly
after updating their status. This is useful with complex DAPM Mixer operations
where we need to do additional work in addition to setting a few mixer register
bits.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator has no power control itself and so shouldn't cause a
power up of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care if any action is taken immediately so let the PM
core defer things if it wants to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modern devices allow systems to enable and disable individual supplies on
the device, allowing additional power saving by switching off regulators
which power portions of the device which are not currently in use. Add a
new SND_SOC_DAPM_REGULATOR_SUPPLY widget type factoring out the code for
managing such widgets from individual drivers.
The widget name will be used as the supply name when requesting the
regulator from the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes a NULL pointer dereference in dapm_power_widgets() if the dapm context
has no codec.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device model needs a release() function so it can free devices when
they become dereferenced. Do that for rtds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As for PCMs take a runtime power management reference to devices that are
in a non-off bias, avoiding the need to do this in individual drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator behaves as an input would but is not considered for
any of the special behaviour associated with external input pins. This
is especially useful when automatically working out not connected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This makes the output a bit less confusing on multi-CODEC systems as the
same pin may appear in multiple CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A card is fully routed if the DAPM route table describes all connections on
the board.
When a card is fully routed, some operations can be automated by the ASoC
core. The first, and currently only, such operation is described below, and
implemented by this patch.
Codecs often have a large number of external pins, and not all of these pins
will be connected on all board designs. Some machine drivers therefore call
snd_soc_dapm_nc_pin() for all the unused pins, in order to tell the ASoC core
never to activate them.
However, when a card is fully routed, the information needed to derive the
set of unused pins is present in card->dapm_routes. In this case, have
the ASoC core automatically call snd_soc_dapm_nc_pin() for each unused
codec pin.
This has been tested with soc/tegra/tegra_wm8903.c and soc/tegra/trimslice.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We really should be doing this in the core, not in a driver...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
The number of connected input and output endpoints for a given widgets
can't change during a DAPM run so there is no need to redo the recursion
through branches of the tree we've already visited. Doing this on one of
my test systems gives an improvement of:
Power Path Neighbour
Before: 63 607 731
After: 63 141 181
which scales up well as more widgets are involved in paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures none of the rest of the code ever encounters a widget which
does not have a power check function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we only have one sync during the initial startup of the card by
making snd_soc_dapm_sync() a noop on non-instantiated cards. This avoids
any bounces due to things like jacks reporting their initial state on
partially initialised cards. The callers that don't also get called at
runtime should just be removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care how many widgets a supply is supplying, we just care
if the number is non-zero. This didn't actually produce any improvement
in the test cases I've been using but seems obviously sensible enough that
I'm pushing it out anyway.
We could do a similar thing for other widgets but this may be unhelpful
for further refactorings Liam was working on aiming to allow us to
identify connected audio paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The whole point of supply widgets is that they aren't inputs to their
sinks so a state change in a supply should never affect the state of the
widget being supplied and we don't need to mark them as dirty.
Power Path Neighbour
Before: 69 727 905
After: 63 607 731
This is particularly useful where supplies affect large portions of the
chip (eg, a bandgap supplying the analogue sections).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some widgets will get power_check() run on them more than once during a
DAPM run, most commonly due to supply widgets checking to see if their
consumers are powered up. It's wasteful to do this so cache the result
of power_check() during a run. For one system I tested this on I got an
improvement of:
Power Path Neighbour
Before: 106 970 1186
After: 69 727 905
from this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Help diagnose why we're checking widgets by providing some logging when
we first dirty them. This should possibly be a trace point if it's useful
but can be absurdly verbose if enabled, we can always change it later if
desired.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If two widgets are not currently connected then there is no need to
propagate a power state change between them as we mark the affected
widgets when we change a connection. Similarly if a neighbour widget is
already in the state being set for the current widget then there is no
need to recheck.
On one system I tested this gave:
Power Path Neighbour
Before: 114 1066 1327
After: 106 970 1186
which is an improvement, although relatively small.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to reduce the number of DAPM power checks we run keep a list of
widgets which have been changed since the last DAPM run and iterate over
that rather than the full widget list. Whenever we change the power state
for a widget we add all the source and sink widgets it has to the dirty
list, ensuring that all widgets in the path are checked.
This covers more widgets than we need to as some of the neighbour widgets
won't be connected but it's simpler as a first step. On one system I tried
this gave:
Power Path Neighbour
Before: 207 1939 2461
After: 114 1066 1327
which seems useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're not actually doing any dynamic power management based on connection
and output drivers (which are pretty much the same thing) are marked as
unconditionally connected already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We've got the same code in two different places, let's have it in a single
place instead.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Future patches will try to reduce the number of widgets we check on each
DAPM run but we're still going to need to look and see if the devices is
on at all so we can manage the overall device bias. Move these checks out
into the main dapm_power_widgets() function so we don't have to think about
them for now.
Once we're doing more incremental updates it'll probably be worth using
refcounts for each bias level to avoid having to do the sweep over all
widgets but that's not going to be where the big performance wins are.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Split the decision about what the new power should be out from the
implementation of that decision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we force all devices in the system to be at the same bias level.
This is due to concerns about power or pop/click impacts from either
ramping VMID or mismatching VMID on the analogue I/O lines between
connected devices but does mean we power devices up more often than we
really need to.
If a device flags idle_bias_off this will usually mean that it's either
all digital or ground referenced (in which case the idle and powered bias
levels are identical) so this concern does not apply and we can save some
power by leaving it off when not needed itself.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The number of times we look at a potentially connected neighbour is just
as important as the number of times we actually recurse into looking at
that neighbour so also collect that statistic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The indentation is getting a little deep. Should be straight code motion,
no functional changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the longest standing areas for improvement in ASoC has been the
DAPM algorithm - it repeats the same checks many times whenever it is run
and makes no effort to limit the areas of the graph it checks meaning we
do an awful lot of walks over the full graph. This has never mattered too
much as the size of the graph has generally been small in relation to the
size of the devices supported and the speed of CPUs but it is annoying.
In preparation for work on improving this insert a trace point after the
graph walk has been done. This gives us specific timing information for
the walk, and in order to give quantifiable (non-benchmark) numbers also
count every time we check a link or check the power for a widget and report
those numbers. Substantial changes in the algorithm may require tweaks to
the stats but they should be useful for simpler things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have dapm_context instead of codec parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently it is only possible to route one source per switch into a mixer.
This patch modifies the code, so that it is possible to route multiple sources
into a mixer via the same switch. One use-case for this is routing a stereo
channel pair into a mono-mixer via the same switch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stream event debug can be noisy on larger audio devices so improve the
debug SNR by changing it to the verbose level.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for Dynamic PCM (AKA DSP) support.
This adds a callback function to be called at the completion of a DAPM stream
event.
This can be used by DSP components to perform calculations based on DAPM graphs
after completion of stream events.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for ASoC Dynamic PCM (AKA DSP) support.
Provide convenience methods to retrieve the soc_card or snd_card from a
DAPM context.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Makes life a little easier if you want to add subsequences to an existing
driver as you can use -1 to put things at the start of sequences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow platform driver widgets to perform any IO required for DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously we were using the DAPM context rather than a widget as the
argument for update_bits() so we didn't need to care that our list walk
of widgets left us one beyond the end of the list. Now we're using them
for the register update we need to make sure we're pointing at an actual
widget not the list_head.
Fix originally suggested by Liam on IM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This time with soc_widget_update_bits reflecting recent soc_update_bits changes.
Currently widget IO is tightly coupled to the CODEC drivers. Future platform DSP
devices have mixer components that can alter power usage and hence require full
DAPM support.
This provides a generic widget IO operation wrapper in preparation for
future patches that implement platform driver DAPM.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Normally DAPM will power up any connected audio path. This is not ideal
for sidetone paths as with sidetone paths the audio path is not wanted in
itself, it is only desired if the two paths it provides a sidetone between
are both active. If the sidetone path causes a power up then it can be
hard to minimise pops as we first power up either the sidetone or the main
output path and then power the other, with the second power up potentially
introducing a DC offset.
Address this by introducing the concept of a weak path. If a path is marked
as weak then DAPM will ignore that path when walking the graph, though all
the relevant controls are still available to the application layer to allow
these paths to be configured.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently it is possible that snd_soc_new_{mixer,mux,pga} is called with a
DAPM context not matching the widgets context. This can lead to a wrong
prefix_len calculation, which will result in undefined behaviour. To avoid
this always use the DAPM context from the widget itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This allows the card driver to use the bias level variable more easily in
multi component systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The card callback will get called for each DAPM context in the card so it
can be useful for it to know which device is currently undergoing a
transition.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
It's redundant now thanks to the use of the generic trace infrastructure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If the only widgets active within a CODEC are supplies and micbiases we
are not passing audio, we are probably just doing microphone detection.
This will not generally require either fully accurate reference voltages
or much power so
If this turns out to be unsuitable for some systems we can provide a
facility to override this decision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Rather than a simple flag to say if we want the DAPM context to be at full
power specify the target bias state. This should have no current effect
but is a bit more direct and so makes it easier to change our decisions
about the which bias state to go into in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Commit af46800 ("ASoC: Implement mux control sharing") introduced
function dapm_is_shared_kcontrol.
When this function returns true, the naming of DAPM controls is derived
from the kcontrol_new. Otherwise, the name comes from the widget (and
possibly a widget's naming prefix).
A bug in the implementation of dapm_is_shared_kcontrol made it return 1
in all cases. Hence, that commit caused a change in control naming for
all controls instead of just shared controls.
Specifically, a control is always considered shared because it is always
compared against itself. Solve this by never comparing against the widget
containing the control being created.
Equally, controls should never be shared between DAPM contexts; when the
same codec is instantiated multiple times, the same kcontrol_new will be
used. However, the control should no be shared between the multiple
instances.
I tested that with the Tegra WM8903 driver:
* Shared is now mostly 0 as expected, and sometimes 1.
* The expected controls are still generated after this change.
However, I don't have any systems that have a widget/control naming
prefix, so I can't test that aspect.
Thanks for Jarkko Nikula for pointing out how to fix this.
Reported-by: Liam Girdwood <lrg@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 52ba67b ("ASoC: Force all DAPM contexts into the same bias state")
powers up all the DAPM contexts in a card if any DAPM context becomes
active. Unfortunately power down newer happens if per-card DAPM context
doesn't have any widgets.
Reason for this is that power state of per-card DAPM context without
widgets is never cleared and thus all the DAPM contexts remain permanently
active. Test for widgetless calling DAPM context in dapm_power_widgets()
doesn't work for per-card DAPM context since power change is never
originating from widgetless per-card DAPM context.
Fix this by pre-clearing power state flag of non-codec DAPM context at the
beginning of power sequence.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Control sharing is enabled when two widgets include pointers to the
same kcontrol_new in their definition. Specifically:
static const struct snd_kcontrol_new adcinput_mux =
SOC_DAPM_ENUM("ADC Input", adcinput_enum);
static const struct snd_soc_dapm_widget wm8903_dapm_widgets[] = {
SND_SOC_DAPM_MUX("Left ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
SND_SOC_DAPM_MUX("Right ADC Input", SND_SOC_NOPM, 0, 0, &adcinput_mux),
};
This is useful when a single register bit or field affects multiple
muxes at once. The common case is to have separate control bits or
fields for each mux (channel). An alternative way of looking at this
is that the mux is a stereo (or even n-channel) mux, rather than
independant mono muxes.
Without this change, a separate kcontrol will be created for each
DAPM_MUX. This has the following disadvantages:
* Confuses the user/programmer with redundant controls that don't
map to separate hardware.
* When one of the controls is changed, ASoC fails to update the DAPM
logic for paths solely affected by the other controls impacted by
the same register bits. This causes some paths not to be correctly
powered up or down. Prior to this change, to work around this, the
user or programmer had to manually toggle all duplicate controls away
from the intended setting, and then back to it.
Control sharing implies that the control is named based on the
kcontrol_new itself, not any of the widgets that are affected by it.
Control sharing is implemented by: When creating kcontrols, if a
kcontrol does not yet exist for a particular kcontrol_new, then a new
kcontrol is created with a list of widgets containing just a single
entry. This is the normal case. However, if a kcontrol does already
exists for the given kcontrol_new, the current widget is simply added
to that kcontrol's list of affected widgets.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future change will allow multiple widgets to be affected by the same
control. For example, a single register bit that controls separate muxes
in both the L and R audio paths.
This change updates the code that handles relevant controls to be able
to iterate over a list of affected widgets. Note that only the put
functions need significant modification to implement the iteration; the
get functions do not need to iterate, nor unify the results, since all
affected widgets reference the same kcontrol.
When creating the list of widgets, always create a 1-sized list, since
the control sharing is not implemented in this change.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Future changes will need reference to the kcontrol created for a given
kcontrol_new. Store the created kcontrol values now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A future change will modify struct snd_soc_dapm_widget to store the
actual kcontrol pointers for each kcontrol_new in a field named
kcontrols. Rename the existing kcontrols field to enable this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove the DAPM debugfs entries before freeing the context's widgets, otherwise a
use after free situation might occur.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently debugfs entries for a DAPM widgets are only added in
snd_soc_dapm_debugfs_init. If a widget is added later (for example in the
dai_link's probe callback) it will not show up in debugfs.
This patch moves the creation of the widget debugfs entry to
snd_soc_dapm_new_widgets where it will be added after the widget has been
properly instantiated.
As a side-effect this will also reduce the number of times the DAPM widget list
is iterated during a card's instantiation.
Since it is possible that snd_soc_dapm_new_widgets is invoked form the codecs or
cards probe callbacks, the creation of the debugfs dapm directory has to be
moved before these are called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the creation of the DAPM debugfs directory to snd_soc_dapm_debugfs_init
instead of having the same duplicated code in both codec and card DAPM setup.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a helper function for searching DAPM widgets by name.
This allows to streamline functions which operate on widgets by name.
It also allows to get rid of copy'n'pasted code which was added to fallback to
widgets from other contexts if the widget was not found in the current context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all widgets on a card are within the codec's DAPM context. Fix
snd_soc_dapm_get_pin_status to search all contexts when looking for a
widget.
This change is required when modifying tegra_wm8903 to use
snd_soc_card.widgets rather than calling snd_soc_dapm_new_controls; the
former adds the widgets to the card's DAPM context, whereas tegra_wm8903
uses the codec's DAPM context when calling snd_soc_dapm_new_controls.
By code inspection, I suspect this also applies to Samsung Speyside.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DAPM pin operations currently require that the specific DAPM context
that the pin being operated in is contained in be specified. With multi
component and especially with the addition of a per-card DAPM context
this isn't ideal as it means that things like disabling unused pins on
CODECs require looking up the CODEC DAPM context.
Fix this by falling back to matching a widget in any context if there isn't
a match in the current context. The code isn't ideal currently but will do
the job.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently we allow all DAPM contexts to determine their own bias level.
While this should in general work in most situations and will deliver the
lowest possible power it causes problems for our integration with the
card bias level as we're calling the card bias level functions for each
DAPM context even though they're card wide but don't say which CODEC
we're calling them for. Mitigate against this by forcing everything to
be in the same state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since we recently explicitly set the register for registerless widgets
to no register there is no longer any need to special case power updates
for them, we can allow them to be handled with the register compression
code as other widgets are.
As this is the only remaining user of dapm_generic_apply_power() and
dapm_update_bits() also remove those functions.
Noticed-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is also in the old sysfs diagnostics but it's nice to have everything
in one place.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're not only prefixing all controls, we're also prefixing the widget
names in the runtime data. This causes us to add the prefix twice - once
when using the widget name to generate the control name and once when
adding the control.
Really we shouldn't be prefixing the widget names at all, the matching
code should be handing this as we always know which DAPM context a
widget came from and always display the widget name in terms of a DAPM
context. However, we're quite close to the merge window and that's
relatively invasive.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Now we've got multi-component we need to make sure that the DAPM context
(and hence register I/O context) we use to apply the pending updates at
the end of a DAPM sequence is the one we were processing rather than the
one that was used to initate the state change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
A CODEC pointer is optional (and is checked for in most contexts within
DAPM) - add checks to the few places where it was missed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than indirecting through the CODEC we can look the card up directly
from the card pointer in the DAPM context.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Sometimes the name of the control switch of a dapm route contains
spaces which makes it impossible to distinguish it from the source widget.
Add quotes around the names of the widgets to makes these parsable.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As bias level changes can be quite time consuming and the bias changes
for multiple devices aren't strongly tied to each other (if anything it
can be advantageous to bring different devices up together) we can improve
the state transition time for multi-component systems by running the bias
level changes for all the devices in parallel. This is very simple to
achieve using the kernel async functionality so use that to schedule the
work.
This should have no practical effect for the overwhelming majority of
systems which have a single DAPM context - we'll bounce into another
thread to do the bias level change but otherwise everything will happen
in exactly the same order as it did before.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
We can get the card from the DAPM context so don't bother passing it as
an argument.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The only thing that should ever be calling this is soc-core and that is
built as part of the same module so doesn't need the export.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If a widget has been force enabled then not only do we need to keep the
widget itself enabled, we also need to keep any supplies the widget
requires enabled. The user could force all the individual widgets on but
this requires too much knowledge of device internals.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
ASoC generally uses the register defaults for everything, but in some
cases the hardware will default to enabling some of the DAPM widgets
(clocks for example). Ensure that DAPM knows about the actual widget
state at initialisation by reading the enable bits after instantiating
the widgets so they don't get left enabled needlessly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
snd_soc_dapm_put_volsw() has variables for both the unshifted and
shifted mask for updates commit 97404f (ASoC: Do DAPM control updates in
the middle of DAPM sequences) got confused between the two of these.
Since there's no need to keep a copy of the unshifted mask fix this and
simplify the code by using only one mask variable.
[Completely rewrote the changelog to describe the issue -- broonie.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allows drivers to distinguish which subsequence is being notified when
they get called back.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Many modern devices have features such as DC servos which take time to start.
Currently these are handled by per-widget events but this makes it difficult
to paralleise operations on multiple widgets, meaning delays can end up
being needlessly serialised. By providing a callback to drivers when all
widgets of a given type have been handled during a DAPM sequence the core
allows drivers to start operations separately and wait for them to complete
much more simply.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
With larger devices there may be many widgets of the same type in series
in an audio path. Allow drivers to specify an additional level of ordering
within each widget type by adding a subsequence number to widgets and then
splitting operations on widgets so that widgets of the same type but
different sequence numbers are processed separately. A typical example
would be a supply widget which requires that another widget be enabled
to provide power or clocking.
SND_SOC_DAPM_PGA_S() and SND_SOC_DAPM_SUPPLY_S() macros are provided
allowing this to be used with PGAs and supplies as these are the most
commonly affected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Rather than passing the sequence to use for DAPM widgets around by reference
explicitly say if we're powering up or down until the point where we need
the sequence itself. This should make no practical difference in itself but
supports future refactoring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This new type is a virtual version of snd_soc_dapm_mux. It is used
when a backing register value is not necessary for deciding which
input path to connect. A simple virtual enumeration control e.g.
SOC_DAPM_ENUM_VIRT() can be exposed to userspace which will be used
to choose which path to connect.
The snd_soc_dapm_virt_mux type ensures that during the initial
path setup, the first (which is also the default) input path will
be connected.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Attempt to minimise audible effects from mixer and mux updates by
implementing the actual register changes between powering down widgets
that have become unused and powering up widgets that are newly used.
This means that we're making the change with the minimum set of widgets
powered, that the input path is connected when we're powering up widgets
(so things like DC offset correction can run with their signal active)
and that we bring things down to cold before switching away. Since
hardware tends to be designed for the power on/off case more than for
dynamic reconfiguration this should minimise pops and clicks during
reconfiguration while active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Power change event like stream start/stop or kcontrol change in a
cross-device path originates from one device but codec bias and widget power
changes must be populated to another devices on that path as well.
This patch modifies the dapm_power_widgets so that all the widgets on a
sound card are checked for a power change, not just those that are specific
to originating device. Also bias management is extended to check all the
devices. Only exception in bias management are widgetless codecs whose bias
state is changed only if power change is originating from that context.
DAPM context test is added to dapm_seq_run to take care of if power sequence
extends to an another device which requires separate register writes.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling widgets from DAPM context is required when extending the ASoC
core to cross-device paths. Even the list of widgets are now kept in
struct snd_soc_card, the widget listing in sysfs and debugs remain sorted
per device.
This patch makes possible to build cross-device paths but does not extend
yet the DAPM to handle codec bias and widget power changes of an another
device.
Cross-device paths are registered by listing the widgets from device A in
a map for device B. In case of conflicting widget names between the devices,
a uniform name prefix is needed to separate them. See commit ead9b91
"ASoC: Add optional name_prefix for kcontrol, widget and route names" for
help.
An example below shows a path that connects MONO out of A into Line In of B:
static const struct snd_soc_dapm_route mapA[] = {
{"MONO", NULL, "DAC"},
};
static const struct snd_soc_dapm_route mapB[] = {
{"Line In", NULL, "MONO"},
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling DAPM paths from DAPM context is a first prerequisite when
extending ASoC core to cross-device paths. This patch is almost a nullop and
does not allow to construct cross-device setup but the path clean-up part in
dapm_free_widgets is prepared to remove cross-device paths between a device
being removed and others.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some cases it was not possible to follow the appropiate power
ON/OFF sequence like in cases where the PGA needs to be enabled
before the driver and disabled before the PGA for pop reduction.
Add a widget to support output driver (speaker, haptic, vibra, etc)
drivers where power ON/OFF ordering is important.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix "ASoC: Fix bias power down of non-DAPM codec" for 3.6.37 will cause a
build error when merging into ASoC for-2.6.38. Fix the issue by doing a
change that commit ce6120c "ASoC: Decouple DAPM from CODECs" would do.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently bias of non-DAPM codec will be powered down (standby/off) whenever
there is a stream stop. This is wrong in simultaneous playback/capture since
the bias is put down immediately after stopping the first stream.
Fix this by using the codec->active count when figuring out the needed bias
level after stream stop.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the machine driver can only do bias level configuration before
the CODEC bias level is brought up. This means that the machine cannot do
any configuration which depends on the CODEC bias level being maintained.
Provide a post-CODEC callback which allows the machine driver to do things
like enable the FLL on a CODEC which is brought down to BIAS_OFF when idle.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need to include soc-dapm.h since soc.h includes it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM widgets may be associated with non-CODEC devices so compare based
on the DAPM context rather than the CODEC pointer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is a need to prefix codec kcontrol, widget and internal route names in
an ASoC machine that has multiple codecs with conflicting names. The name
collision would occur when codec drivers try to registering kcontrols with
the same name or when building audio paths.
This patch introduces optional prefix_map into struct snd_soc_card. With it
machine drivers can specify a unique name prefix to each codec that have
conflicting names with anothers. Prefix to codec is matched with codec
name.
Following example illustrates a machine that has two same codec instances.
Name collision from kcontrol registration is avoided by specifying a name
prefix "foo" for the second codec. As the codec widget names are prefixed
then second audio map for that codec shows a prefixed widget name.
static const struct snd_soc_dapm_route map0[] = {
{"Spk", NULL, "MONO"},
};
static const struct snd_soc_dapm_route map1[] = {
{"Vibra", NULL, "foo MONO"},
};
static struct snd_soc_prefix_map codec_prefix[] = {
{
.dev_name = "codec.2",
.name_prefix = "foo",
},
};
static struct snd_soc_card card = {
...
.prefix_map = codec_prefix,
.num_prefixes = ARRAY_SIZE(codec_prefix),
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that we keep all widget powerups in DAPM sequence by making
the CODEC the last thing we compare on rather than the first thing.
Also fix the fact that we're currently comparing the widget pointers
rather than the CODEC pointers when we do the substraction so we
won't get stable results.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace events for DAPM allow us to monitor the performance and behaviour
of DAPM with logging which can be built into the kernel permanantly, is
more suited to automated analysis and display and less likely to suffer
interference from other logging activity.
Currently trace events are generated for:
- Start and stop of DAPM processing
- Start and stop of bias level changes
- Power decisions for widgets
- Widget event execution start and stop
giving some view as to what is happening and where latencies occur.
Actual changes in widget power can be seen via the register write trace in
soc-core.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make the DAPM sequence execution look a bit nicer by factoring out the
code to invoke an event into a single function since it's all the same
pretty much.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Prints from pop_dbg are enabled when dapm_pop_time != 0. Convert it to
use dev_info so that parent device of DAPM context is printed.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Switch printk and pr_ prints to dev_ variants. It is helpful to see
parent device of DAPM context especially when there are multiple DAPM
contexts (codecs currently).
This is mostly simple conversion. Exceptions are in snd_soc_dapm_set_pin
that prints also pin state, uniform "dapm: unknown pin" error prints from
snd_soc_dapm_set_pin, snd_soc_dapm_force_enable_pin and
snd_soc_dapm_ignore_suspend, and pop_dbg which is converted by an another
patch.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Based on discussion the dapm_pop_time in debugsfs should be per card rather
than per device. Single pop time value for entire card is cleaner when the
DAPM sequencing is extended to cross-device paths.
debugfs/asoc/{card->name}/{codec dir}/dapm_pop_time
->
debugfs/asoc/{card->name}/dapm_pop_time
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Decoupling Dynamic Audio Power Management (DAPM) from codec devices is
required when developing ASoC further. Such as for other ASoC components to
have DAPM widgets or when extending DAPM to handle cross-device paths.
This patch decouples DAPM related variables from struct snd_soc_codec and
moves them to new struct snd_soc_dapm_context that is used to encapsulate
DAPM context of a device. ASoC core and API of DAPM functions are modified
to use DAPM context instead of codec.
This patch does not change current functionality and a large part of changes
come because of structure and internal API changes.
Core implementation is from Liam Girdwood <lrg@slimlogic.co.uk> with some
minor core changes, codecs and machine driver conversions from
Jarkko Nikula <jhnikula@gmail.com>.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Cliff Cai <cliff.cai@analog.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Timur Tabi <timur@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Arnaud Patard (Rtp) <arnaud.patard@rtp-net.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jassi Brar <jassi.brar@samsung.com>
Cc: Daniel Gloeckner <dg@emlix.com>
Cc: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some devices can usefully run audio while the Linux system is suspended.
One of the most common examples is smartphone systems, which are normally
designed to allow audio to be run between the baseband and the CODEC
without passing through the CPU and so can suspend the CPU when on a
voice call for additional power savings.
Support such systems by providing an API snd_soc_dapm_ignore_suspend().
This can be used to mark DAPM endpoints as not being sensitive to
system suspend. When the system is being suspended paths between
endpoints which are marked as ignoring suspend will be kept active.
Both source and sink must be marked, and there must already be an
active path between the two endpoints prior to suspend.
When paths are active over suspend the bias management will hold the
device bias in the ON state. This is used to avoid suspending the
CODEC while it is still in use.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Instead of using stream events to handle power down during suspend
integrate the handling with the normal widget path checking by
replacing all cases where we report a connected endpoint in a path
with a function snd_soc_dapm_suspend_check() which looks at the ALSA
power state for the card and reports false if we are in a D3 state.
Since the core moves us into D3 prior to initating the suspend all
power checks during suspend will cause the widgets to be powered
down. In order to ensure that widgets are powered up on resume set
the card to D2 at the start of resume handling (ALSA API calls
require D0 so we are still protected against userspace access).
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We now manage suspend within the main power analysis rather than by
flipping the state of widgets.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Some systems, such as those with mechanical jack detection, may wish
to force enable a pin (typically mic bias) only some of the time.
Support such systems by having disable_pin() also coveer force enabled
pins.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
A code audit reveals that there are currently no users of the widget
controls on PGAs. This is likely to continue to be the case since
while there are useful things that can be done with integrating the
PGA gain and mute controls with the power sequencing userspace
generally wants stereo controls for output stages which this doesn't
map onto well.
In preparation for implementing something more useful strip out the
existing code, leaving the parameters there for use by the new code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Allow pins to be forced on regardless of their power state. This is
intended for use with microphone bias supplies which need to be
enabled in order to support microphone detection - in systems without
appropriate hardware leaving the microphone unbiased when not in use
saves power.
The force done at power check time in order to avoid disrupting other
power detection logic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently during pop/click debug we're inserting a delay both after
every log message we generate and at explicit points in the sequence,
slowing things down even further than they need to be especially when
many writes get coalesced by the sequence generation code.
Remove the per-printk delay and ensure that we have explicit delays
where we say we want them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently ASoC always maintains the bias of the CODEC while the system
is active. With older mobile CODECs this is required since the outputs
are referenced to a non-zero voltage and enabling or disabling this
voltage without audible pops or clicks in the output takes too long to
do when starting or stopping audio.
As a result of features such as ground referenced outputs and class D
speaker drivers current generation devices are able to power on and off
much more quickly without these system level issues so provide a new
flag idle_bias_off in snd_soc_codec which will cause the core to turn
off the CODEC bias. The distinction between STANDBY and OFF is still
maintained. This is partly for consistency but also allows for
potential future extensions such as per-machine overrides or deferring
the bias removal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The same information is now visible via debugfs and with large modern
devices dumping everything to the console can be very resource
intensive, causing more harm than good.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
In preparation for multiple device support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
No need for the mixers to know about this, and it allows for virtual
controls.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Make it a bit easier to tie DAPM widgets in with the register map
without referring to the source by including the register location
controlled by the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
When we get a stream suspend event force the power down since otherwise
the stream would remain marked as active. In future we'll probably want
to make this stream-specific and add an interface to make the power down
of other widgets optional in order to support leaving bypass paths
active while suspending the processor.
Cc: stable@kernel.org
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Access to damp_power_widgets() is assumed to be single-threaded.
Concurrent accesses to dapm_power_widgets() may result in
unpredictable behavior.
Calls from:
close_delayed_work()
soc_codec_close()
soc_pcm_prepare()
soc_suspend()
soc_resume_deferred()
to snd_soc_dapm_stream_event() do not have the codec->mutex
taken to cover the call to dapm_power_widgets(). Thus, take
the mutex in these paths also to assure single-threaded use
of dapm_power_widgets().
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes it is desirable to have a mux which does not reflect any
direct register configuration but which will instead only have an
effect implicitly (for example, as a result of changing which parts
of the device are powered up). Provide a virtual mux for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to check for an event callback since we also check for
an appropriate event flag when applying mux status changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the SND_SOC_DAPM_LINE can be input or output, additional check is
needed in order to determine if the widget is connected as input or
output.
When checking for connected outputs, if the widget is line, than check
if the sources list is not empty (line is connected as output)
For input endpoint check, when the widget is line, also check if the
sinks list is not empty (line is connected as input).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some chips with complex internal supply (particularly clocking)
arragements may have multiple options for some of the supply
connections. Since these don't affect user-visible audio routing
the expectation would be that they would be managed automatically
by one of the drivers.
Support these users by allowing routes to have a connected function
which is queried before the connectedness of the path is checked as
normal. Currently this is only done for supplies, other widgets
could be supported but are not currently since the expectation for
them is that audio routing will be under the control of userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently when built with DEBUG DAPM will dump information about
the power state decisions it is taking for each widget to dmesg.
This isn't an ideal way of getting the information - it requires
a kernel build to turn it on and off and for large hub CODECs the
volume of information is so large as to be illegible. When the
output goes to the console it can also cause a noticable impact
on performance simply to print it out.
Improve the situation by adding a dapm directory to our debugfs
tree containing a file per widget with the same information in
it. This still requires a decision to build with debugfs support
but is easier to navigate and much less intrusive.
In addition to the previously displayed information active streams
are also shown in these files.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the CODEC does not provide a set_bias_level() then update the
bias_level variable for it since other parts of the system expect
that to be maintained.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently DAPM interfaces with the audio streams to and from the
processor at the DAC and ADC widgets. As the digital capabilities
of parts increases this is becoming a less and less able to meet
the needs of parts.
To meet the needs of these devices create new widgets interfacing
with the TDM bus but not integrated into any other functionality.
Audio can then be routed to and from these widgets using existing
routing widgets.
A slot number is provided in the definition but this is currently
not used yet. This is intended to support devices which can use
more than one TDM slot on a single interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Speaker and headphone outputs do not need to be handled separately
since they can't be part of the same path.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the system doesn't have any DAPM widgets then we can't use their
state to check if the bias level for the codec should be up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In SOC DAPM layer of SOUND subsystem, when add signal route (in the
function snd_soc_dapm_add_route() ), the original code has wrong logic
when dapm layer check each widget whether an external one.
Signed-off-by: Rongrong Cao <rrcao@ambarella.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the audio subsystem is powered down cleanly when the system
shuts down by providing a shutdown operation. This ensures that all the
components have been returned to an off state cleanly which should avoid
audio issues from partially charged capacitors or noise on digital inputs
if the system is restarted quickly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Ben Dooks <ben-linux@fluff.org>
They are now only accessed within dapm_power_widgets() so can be local
to that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle gain ramping for PGAs so we can coalesce their power updates too.
This is not ideal since we can't cope properly with gain ramping for
stereo paths but that was the case without coalescing and gain ramping
is relatively infrequently used so the effects are limited.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The more flexible value muxes and named mixers don't need to be sorted
differently from a power management point of view, they are different
only in terms of the control interface and not in terms of seqencing
behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reduce the number of register writes we need to set the power state for
a CODEC by coalescing updates to widgets with the same sequence order and
same register into a single write.
This can be a noticable performance improvement with slow or heavily
contended control buses, such as I2C controllers with a low clock
frequency, and is particularly noticable when resuming. It can also
reduce the noticability of and pops and clicks by ensuring that left
and right channels are powered simultaneously if they are in the same
register.
Currently widgets that have events are not coalesced, including PGAs
which may use the volume ramping control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the remaining unsigned shorts with unsigned ints.
Tested with pcap2 codec (25 bits registers).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lump the list walk into a single function, and pull in the power
application too so we can do some further refactoring. Pure code
motion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the past the DAPM power sequencing was done by iterating over the list
of widgets once for each widget type and powering widgets of that type.
Instead of doing that do the sorting at the time we insert the widgets
into the lists of widgets to apply power changes to. This reduces the
amount of computation required for seqencing still further, though the
costs are generally dwarfed by the costs of the register writes
implementing them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.
The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.
Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.
Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is simple code motion, intended to support future refactoring of
the DAPM algorithms and (more immediately) the additon of events for
DACs and ADCs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_dapm_switch ends up ends up in dapm_new_mixer() (since a switch
is a special case of a mixer with only one input) but this wasn't
correctly handled in the code.
Also fix the coding style for the switch below while we're here.
Reported-by: Joonyoung Shim <dofmind@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On some systems it is desirable for control for DAPM pins to be provided
to user space. This is the case with things like GSM modems which are
controlled primarily from user space, for example. Provide a helper which
exposes the state of a DAPM pin to user space for use in cases like this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the check for the mux type to also handle the
snd_soc_dapm_value_mux type in a same way as the snd_soc_dapm_mux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge the recently introduced soc_value_enum structure to the soc_enum.
The value based enums are still handled separately from the normal enum types,
but with the merge some of the newly introduced functions can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows you to define the mixer paths as having the same name as the
paths they represent.
This is required to support codecs such as the wm9705 neatly without extra
controls in the alsa mixer.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
This patch introduces a new enum type.
In this enum type each enumerated items referred with a value.
This new enum type can handle enums encoded in bitfield, or any other
weird ways. twl4030 codec has several mux selection register, where the
input/output mux is coded in a bitfield. With the normal enum type this type
of mux can not be handled in a clean way.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This should never happen and it's helpful to identify the specific control
that failed when it does happen.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the issues with the ASoC v1 API which has been addressed in the
ASoC v2 work that Liam Girdwood has done is that the ALSA card provided
by ASoC is distributed around the ASoC structures. For example, machine
wide data such as the struct snd_card are maintained as part of the
CODEC data structure, preventing the use of multiple codecs. This has
been addressed by refactoring the data structures so that all the data
for the ALSA card is contained in a single structure snd_soc_card which
replaces the existing snd_soc_machine and snd_soc_device.
Begin the process of backporting this by renaming struct snd_soc_machine
to struct snd_soc_card, better reflecting its function and bringing it
closer to standard ALSA terminology.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call device_create_file only once in snd_soc_dapm_sys_add function.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_sys_add':
sound/soc/soc-dapm.c:828: error: 'ret' undeclared (first use in this function)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As well as ensuring that UI-relevant parts of control names don't get
truncated in the DAPM code this avoids conflicts in long control names
that differ only at the end of a long string.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
i.e. echo 6 59 >/sys/kernel/debug/soc-audio.0/codec_reg
will set register 0x06 to a value of 0x59.
Also, pop_time debugfs interface setup is moved so that it
is setup in the same function as codec_reg
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This was marked as deprecated in 2.6.27 and all users except for
playpaq_wm8510 fixed in that release.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update the contact information for Liam Girdwood in ASoC core and
drivers as my old email address is no longer valid.
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new API call snd_soc_dapm_nc_pin() which allows machine drivers to
mark pins as being permanently disabled. At present this is identical
to snd_soc_dapm_disable_pin() except in terms of improving the internal
documentation of machine drivers that use it. The intention is that in
future it will be extended to provide additional features such as hiding
controls that are only relevant to paths using the disconnected pin.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Function dapm_mux_update_power needs enum index mux and register mask value val
as parameters, but it only has a parameter val, and uses it as both val and mux.
snd_soc_test_bits(widget->codec, e->reg, mask, val) val is register mask here,
e->texts[val] but val should be enum index mux here.
This patch adds a new param mux to fix it.
Signed-off-by: Richard Zhao <linuxzsc@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Pop time configuration is a debugging feature which shouldn't be used in
normal operation so move it to debugfs where it is clearer. This also
simplifies the code since debugfs provides standard facilities for
exposing simple integer values to user space.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASOC: convert use of uint to unsigned int
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Most of the ASoC controls refer to the maximum value that can be set for
a control as mask but there is no actual requirement for all bits to be
set at the highest possible value making the name mask misleading.
Change the code to use max instead.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Convert bitfields in ASoC into full int width. This is a
simple mechanical conversion. Two places in the DAPM code
were fixed to properly use mask.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
dapm_reg_event() is used by devices using SND_SOC_DAPM_REG() so needs to
be exported to support building them as modules and prototyped to avoid
sparse warnings and potential build issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows pre and post event hooks to be provided for PGA widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DAPM event callback code has many layers of indentation, taking it
over 80 columns. Refactor the code to give less indentation in order to
avoid checkpatch issues on further changes and exploding indentation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Explicit DAPM syncs are likely to cause DAPM state updates, as are mixer
and mux configuration changes, so display the DAPM status after them too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
DAPM contains debug output controlled by a DAPM_DEBUG macro. Change this
to be controlled by the standard DEBUG, dropping the custom dbg() macro
as we go.
Also fix the error printed when configuring an unknown pin to be an
unconditionally displayed error rather than debug output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
DAPM supports adding a compile time configurable delay to the widget power
sequences, aiding diagnosis of problems with pops and clicks being
generated during them. This patch converts this to be configurable at run
time via a sysfs file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This generic register modifier widget is for updating multiple codec
register bits at once when the widget changes its power state.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Currently the ASoC core configures the bias levels in the system using
a callback on codecs and machines called 'dapm_event', passing it PCI
style power levels as SNDRV_CTL_POWER_ constants. This is more obscure
than it needs to be and has caused confusion to driver authors,
especially given that DAPM is also performing power management.
Address this by renaming the callback function to 'set_bias_level' and
using constants explicitly representing the off, standby, pre-on and on
states which DAPM transitions through.
Also unexport the API for setting bias level: there are currently no
in-tree users of this API other than the core itself and it is likely
that the core would need to be extended to cater for any users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The overwhelming majority just say 'initial version' anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASoC codecs and machine drivers that use DAPM routes all cut'n'paste a
loop iterating over a null terminated array of routes. Factor out this
into a bulk registration function, improving the error reporting for
most users, and deprecate the old API to help out of tree users pick up
the changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Graeme Gregory <graeme@openmoko.org>
Cc: Frank Mandarino <fmandarino@endrelia.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Most SoC drivers cut'n'paste a loop iterating over an array to register
their DAPM controls. Provide a function they can call instead.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Graeme Gregory <graeme@openmoko.org>
Cc: Frank Mandarino <fmandarino@endrelia.com>
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This adds a hook to read the power state of a DAPM widget, I use this
in the gta02 driver to expose certain DAPM widgets in the mixer for
ease of audio routing.
Signed-off-by: Graeme Gregory <graeme@openmoko.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
When logging register changes in DAPM debug output include the register
number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_soc_dapm_new_widgets() takes the codec lock when adding new widgets,
causing lockdep warnings when applications later call down through ALSA
to adjust controls. Since widgets are only added during probe this lock
should be unneeded so don't take it.
Thanks to Dmitry Baryshkov <dbaryshkov@gmail.com> for reporting this issue.
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added a device level dapm event so that both the machine and codec are informed
when dapm events occur.
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Fix schedule_timeout() use in alsa-kernel. Mostly just
schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.
Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes an issue whereby power was applied to any inactive
analog path that would leave and reenter a codec (e.g. ACOP -> ACIN on
WM8753). This change now checks for such paths and DAPM will power them
down when not in use.
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes a bug whereby an unnamed stream would cause a NULL
pointer ref in snd_soc_dapm_stream_event().
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Liam Girdwood <lg@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
soc-dapm
·Removed list_for_each since the loop is list_for_each_entry() and
not list_for_each(). Thanks to Liam Girdwood and Seth Forshee.
at91-i2s
·Fixed typo in dai modes definition.
·Fixed struct member name in at91_ssc_info->ssc_state.
·Fixed compilation problem, ssc_state is bundled in at91_ssc_info.
Signed-off-by: Raúl Sánchez Siles <rss@barracuda.es>
Signed-off-by: Seth Forshee <seth.forshee@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Make the following needlessly global functions static:
- dapm_power_widgets()
- dapm_mux_update_power()
- dapm_mixer_update_power()
- dapm_free_widgets()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds Dynamic Audio Power Management (DAPM) to ASoC.
Dynamic Audio Power Management (DAPM) is designed to allow portable and
handheld Linux devices to use the minimum amount of power within the
audio subsystem at all times. It is independent of other kernel PM and
as such, can easily co-exist with the other PM systems.
DAPM is also completely transparent to all user space applications as
all power switching is done within the ASoC core. No code changes or
recompiling are required for user space applications. DAPM makes power
switching decisions based upon any audio stream (capture/playback)
activity and audio mixer settings within the device.
DAPM spans the whole machine. It covers power control within the entire
audio subsystem, this includes internal codec power blocks and machine
level power systems.
There are 4 power domains within DAPM:-
1. Codec domain - VREF, VMID (core codec and audio power)
Usually controlled at codec probe/remove and suspend/resume, although
can be set at stream time if power is not needed for sidetone, etc.
2. Platform/Machine domain - physically connected inputs and outputs
Is platform/machine and user action specific, is configured by the
machine driver and responds to asynchronous events e.g when HP are
inserted
3. Path domain - audio subsystem signal paths
Automatically set when mixer and mux settings are changed by the user.
e.g. alsamixer, amixer.
4. Stream domain - DAC's and ADC's.
Enabled and disabled when stream playback/capture is started and stopped
respectively. e.g. aplay, arecord.
All DAPM power switching decisions are made automatically by consulting
an audio routing map of the whole machine. This map is specific to each
machine and consists of the interconnections between every audio
component (including internal codec components).
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
