Attempting to create the route as part of adding a mux control causes us
to attempt to add the same route twice since we loop over all sources
for the mux after creating the control. Instead do the addition in the
callers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
ASoC automatically creates snd_soc_dapm_dai_in and snd_soc_dapm_dai_out
widgets for DAI drivers, and adds them to the list. Later on, ASoC
creates automatic routes between these widgets and a widget with a
stream name.
We look for a snd_soc_dapm_dai_in or snd_soc_dapm_dai_out widget, and
use this to obtain the DAI structure. We then scan all widgets for
any with a stream name refering to either the capture or the playback
stream, and create routes.
If you have both a snd_soc_dapm_dai_in and a snd_soc_dapm_dai_out
referring to the same DAI structure, this ends up creating one set of
routes for the DAI for the snd_soc_dapm_dai_in widget, and a duplicated
set of routes for the snd_soc_dapm_dai_out widget.
Fix this by checking that the stream name for the widget matches the
DAI widget name.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some devices have the problem that if a internal audio signal source is disabled
the output of the source becomes undefined or goes to a undesired state (E.g.
DAC output goes to ground instead of VMID). In this case it is necessary, in
order to avoid unwanted clicks and pops, to disable any mixer input the signal
feeds into or to active a mute control along the path to the output. Often it is
still desirable to expose the same mixer input control to userspace, so cerain
paths can sill be disabled manually. This means we can not use conventional DAPM
to manage the mixer input control. This patch implements a method for letting
DAPM overwrite the state of a userspace visible control. I.e. DAPM will disable
the control if the path on which the control sits becomes inactive. Userspace
will then only see a cached copy of the controls state. Once DAPM powers the
path up again it will sync the userspace setting with the hardware and give
control back to userspace.
To implement this a new widget type is introduced. One widget of this type will
be created for each DAPM kcontrol which has the auto-disable feature enabled.
For each path that is controlled by the kcontrol the widget will be connected to
the source of that path. The new widget type behaves like a supply widget,
which means it will power up if one of its sinks are powered up and will only
power down if all of its sinks are powered down. In order to only have the mixer
input enabled when the source signal is valid the new widget type will be
disabled before all other widget types and only be enabled after all other
widget types.
E.g. consider the following simplified example. A DAC is connected to a mixer
and the mixer has a control to enable or disable the signal from the DAC.
+-------+
+-----+ | |
| DAC |-----[Ctrl]-| Mixer |
+-----+ : | |
| : +-------+
| :
+-------------+
| Ctrl widget |
+-------------+
If the control has the auto-disable feature enabled we'll create a widget for
the control. This widget is connected to the DAC as it is the source for the
mixer input. If the DAC powers up the control widget powers up and if the DAC
powers down the control widget is powered down. As long as the control widget
is powered down the hardware input control is kept disabled and if it is enabled
userspace can freely change the control's state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
list_first_entry() will always return a valid pointer, even if the list is
empty. So the check whether path is NULL will always be false. So we end up
calling dapm_create_or_share_mixmux_kcontrol() with a path struct that points
right in the middle of the widget struct and by trying to modify the path the
widgets memory will become corrupted. Fix this by using list_emtpy() to check if
the widget doesn't have any paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
When calling krealloc for the kcontrol data the items in the path list that
point back to the head of the list will now point to freed memory, which causes
the list to become corrupted. To fix this, instead of resizing the whole data
struct, only resize the widget list.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_cnew() can return NULL, so we should check the result before trying to
use it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a typo here so we end up using the old freed pointer instead of
the newly allocated one. (If the "n" is zero then the code works,
obviously).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Wait with updating the widgets power field until the changes are actually
written to the hardware in dapm_seq_run_coalesced(). This will allow us to query
the current hardware state between calling dapm_power_one_widget() and actually
writing the new power state to hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_dapm_add_path() is similar to snd_soc_dapm_add_route() except that it
expects the pointer to the source and sink widgets instead of their names. This
allows us to simplify the case where we already have a pointer to widgets. (E.g.
as we have in snd_soc_dapm_link_dai_widgets()). snd_soc_dapm_add_route() will be
updated to just look up the widget and then use snd_soc_dapm_add_path() to
handle everything else.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently the DAPM code is limited to only setting or clearing a single bit in a
register to power a widget up or down. This patch extends the DAPM code to be
more flexible in that regard and allow widgets to use arbitrary values to be
used to put a widget in either on or off state.
Since the snd_soc_dapm_widget struct already contains a on_val and off_val field
no additional fields need to be added and in fact the invert field can even be
removed. Also the generated code is slightly smaller.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently we store for each path which control (if any at all) is associated
with that control. But we are only ever interested in the reverse relationship,
i.e. we want to know all the paths a certain control is associated with. This is
currently implemented by always iterating over all paths. This patch updates the
code to keep a list for each control which contains all the paths that are
associated with that control. This improves the run time of e.g.
soc_dapm_mixer_update_power() and soc_dapm_mux_update_power() from O(n) (with n
being the number of paths for the card) to O(1).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 'value' field is really per control and not per widget. Currently it is only
used for virtual MUXes, which only have one control per widget. So in that case
there is not so much of a difference between whether it is stored per widget or
per control. Moving the 'value' field from the widget to the control will allow
us to use it also for cases where we have more than one control per widget. E.g.
for mixers with multiple input controls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In preparation for adding additional per control data wrap all access to the
widget list in helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use the same 3 lines to get the CODEC for a kcontrol in a quite a few places.
This patch puts them into a common helper function. Having this encapsulated in
a helper function will also make it more easier to eventually change the data
layout of the kcontrol's private data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
DAPM operations are always performed on the card as a whole. Yet (primarily for
historic reasons) dapm_power_widgets() takes a DAPM context as its parameter.
The DAPM context is mainly used to look up a pointer to the card. The same is
true for a couple of functions that are being called from dapm_power_widgets().
This patch changes the signature of dapm_power_widgets() and a couple of related
functions to take a snd_soc_card instead of a snd_soc_dapm_context.
Some of the functions also use the DAPM's device to print error and debug
messages. This can be a bit confusing though since this means the messages for
all widgets, also those from other contexts, will be printed with that device.
The patch updates those cases to use the device of the widget's DAPM context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The update field of a DAPM context is only assigned while the card's dapm_mutex
is locked, the field is also cleared again while the mutex is stil locked. So
there will only ever be one DAPM context at a time with a non-NULL update field.
So it is safe to move the update field from the DAPM context struct to the card
struct. Doing so will allow further cleanups in this area.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to avoid race conditions the assignment of dapm->update should happen
while card->dapm_mutex is being held. To allow CODEC drivers to run a register
update when using snd_soc_dapm_mux_update_power() or
snd_soc_dapm_mixer_update_power() add a update parameter to these two functions.
The update parameter will be assigned to dapm->update while card->dapm_mutex is
locked.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently when updating a control that is shared between multiple widgets the
whole power-up/power-down sequence is being run once for each widget. The
control register is updated during the first run, which means the CODEC internal
routing is also updated for all widgets during this first run. The input and
output paths for each widgets are only updated though during the respective run
for that widget. This leads to a slight inconsistency between the CODEC's
internal state and ASoC's state, which causes non optimal behavior in regard to
click and pop avoidance.
E.g. consider the following setup where two MUXs share the same control.
+------+
A1 ------| |
| MUX1 |----- C1
B1 ------| |
+------+
|
control ---+
|
+------+
A2 ------| |
| MUX2 |----- C2
B2 ------| |
+------+
If the control is updated to switch the MUXs from input A to input B with the
current code the power-up/power-down sequence will look like this:
Run soc_dapm_mux_update_power for MUX1
Power-down A1
Update MUXing
Power-up B1
Run soc_dapm_mux_update_power for MUX2
Power-down A2
(Update MUXing)
Power-up B2
Note that the second 'Update Muxing' is a no-op, since the register was already
updated.
While the preferred order for avoiding pops and clicks should be:
Run soc_dapm_mux_update_power for control
Power-down A1
Power-down A2
Update MUXing
Power-up B1
Power-up B2
This patch changes the behavior to the later by running the updates for all
widgets that the control is attached to at the same time.
The new code is also a bit simpler since callers of
soc_dapm_{mux,muxer}_update_power don't have to loop over each widget anymore
and neither do we need to keep track for which of the kcontrol's widgets the
current update is.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
soc_dpcm_runtime_update() operates on a ASoC card as a whole. Currently it takes
a snd_soc_dapm_widget as its only parameter though. The widget is then used to
look up the card and is otherwise unused. This patch changes the function to
take a pointer to the card directly. This makes it possible to to call
soc_dpcm_runtime_update() for updates which are not related to one specific
widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As noticed by Lars-Peter Clausen since the move to using widgets to hook
into the DAIs we no longer directly manage the power of AIF or DAC/ADC
widgets from the stream integration so they can just use the generic power
checks instead of the custom stream integration ones they currently do.
Signed-off-by: Mark Brown <broonie@linaro.org>
The ALSA core expect the put callback of a control to return 1 if the value of
the control changed and 0 if it did not. Both snd_soc_dapm_put_volsw() and
snd_soc_dapm_put_enum_virt() currently always returns 0. For both functions we
already have a 'change' variable which either contains 1 or 0 depending on
whether the value has changed or not, so just return that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
These two functions were added two years ago in commit 4805608 ("ASoC: dapm -
Add methods to retrieve snd_card and soc_card from dapm context.") but have
remained unused so far. Considering that the dapm context actually has a direct
pointer to the card the functions also seem to be unnecessary. E.g. the
expressions 'dapm_get_soc_card(dapm)' and 'dapm->card' yield the same result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power up/down sequence order for DAPM switch widgets is not explicitly
initialized, causing them to be run always as the first widget type for both
power up and down. Move it to the same position in the sequence as other mixer
widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 85762e71 ("ASoC: dapm: Implement mixer control sharing") the
long_name field of the snd_soc_dapm_path struct is unused. All of the name
handling now happens entirely in dapm_create_or_share_mixmux_kcontrol(). So we
can remove the long_name field from the snd_soc_dapm_path struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have the same code for freeing a DAPM path in three different locations.
Introduce a new helper function to take care of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The condition 'i == item' is only true when, well, 'i' equals 'item'.
So just use 'item' directly as the index into the array.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The private data containing the widget list that is a assigned to a DAPM
kcontrol is never freed. Setup the private_free for DAPM kcontrols to take care
of this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Even though they are virtual widgets DAI widgets still get counted for the
DAPM context power management so we can't just use the active state to
check if they should be powered as they may not be part of a complete path.
Instead split them into input and output widgets and do the same power
checks as we perform on AIFs.
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The power_list field is used when adding a widget to a power sequence list. Use
the same field when iterating the list using list_for_each_entry, otherwise
we'll see undefined behavior.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
kasprintf calculates the size of the result string, allocates a buffer large
enough to hold the string and then performs the format string operation. There
are a couple of places in ASoC where these three steps are done by hand and
where kasprintf can be used instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices may benefit from being able to start some parts of the widget
power up/down sequence earlier on in the sequence than the point at which
the final power state is committed. Support these by providing events which
are called before any power state changes are done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WQzu
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A few more bug fixes, the DAPM clock fix is actually a driver specific
one since currently there's only one user of the clock support due to
the problems relying on the clock API.
Update dapm_clock_event to use clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When clearing the walked flags there is no need to clear all paths, we
only need to clear the paths we actually walked. This means we can split
dapm_clear_walk() into input and output versions and rather than going
through all DAPM paths we can recurse down the path until we encounter
paths we have not yet walked.
This reduces the number of operations we need to perform and improves
cache locality.
[Pulled out of the vendor tree that the patch was originally generated
for by me, any bugs were introduced in that process -- broonie]
Signed-off-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We already clear the walked state in dapm_widget_power_check(), no need
to do it again.
Signed-off-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the equivalent of commit af46800 "ASoC: Implement mux control
sharing", but applied to mixers instead of muxes.
This allows a single control to affect multiple mixer widgets at once,
which is useful when there is a single set of register bits that affects
multiple mixers in HW, for example both the L and R mixers of a stereo
path.
Without this, you either:
1) End up with multiple controls that affect the same register bits, but
whose DAPM state falls out of sync with HW, since the DAPM state is only
updated for the specific control that is modified, and not for other
paths that are affected by the register bit(s).
2) False paths through DAPM, since you end up merging unconnected stereo
paths together into a single widget which hosts the single control, and
then branching back out again, thus conjoining the enable states of the
two input paths.
Now that the kcontrol creation logic is split out into a separate
function, dapm_create_or_share_mixmux_kcontrol(), also use that to
replace most of the body of dapm_new_mux(). This should produce no
functional change, but simply eliminates some mostly duplicated code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
*path is not yet initialized when we check if the widget is connected.
The compiler also warns about this:
sound/soc/soc-dapm.c: In function 'is_connected_output_ep':
sound/soc/soc-dapm.c:824:18: warning: 'path' may be used uninitialized in this function
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 497098be ("ASoC: dapm: Remove bodges for no-widget CODECs") removed the
last user of the n_widgets field. Currently it is incremented for each widget
added, but the value is never used, so we can remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently if a path loops back on itself we correctly skip over it to
avoid going into an infinite loop but this causes us to ignore the need
to power up the path as we don't count the loop for the purposes of
counting inputs and outputs. This means that internal loopbacks within a
device that have powered devices on them won't be powered up.
Fix this by treating any path that is currently in the process of being
recursed as having a single input or output so that it is counted for
the purposes of power decisions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Help avoid noise from the power up of the capture path propagating through
into the start of the recording (especially noise caused by the ramp of
microphone biases) by keeping the capture muted until after we've finished
powering things up with DAPM in the same manner we do for playback. This
allows us to take advantage of soft mute support in the hardware more
effectively and is more consistent.
The core code using the existing digital mute operation is updated to take
advantage of this. Some additional cases in the soc-pcm code and suspend
will need separate handling but these are less practically relevant than
the main runtime stream start/stop case.
Rather than refactor the digital mute function in every single driver a
new operation is added for drivers taking advantage of this functionality,
the old operation should be phased out over time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Enable bypass when the regulator is idle, not when it is in use. This is
consistent with what the few existing users actually want.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC has a mixture of message prefixes e.g. "ASoC", "asoc"
or none and message types e.g. pr_debug or dev_dbg.
Make sure all ASoC core messages use the same "ASoC" prefix and
convert any component device specific messages to use dev_dbg
instead of pr_debug.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM shutdown incorrectly uses "list" field of codec struct while
iterating over probed components (codec_dev_list). "list" field
refers to codecs registered in the system, "card_list" field is
used for probed components.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Allow regulators managed via DAPM to make use of the bypass support that
has recently been added to the regulator API by setting a flag
SND_SOC_DAPM_REGULATOR_BYPASS. When this flag is set the regulator will
be put into bypass mode before being disabled, allowing the regulator to
fall into bypass mode if it can't be disabled due to other users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For ENUM controls the bitmask is calculated based on the number of items.
Currently this is done each time the control is accessed. And while the
performance impact of this should be negligible we can easily do better. The
roundup_pow_of_two macro performs the same calculation which is currently done
manually, but it is also possible to use this macro with compile time constants
and so it can be used to initialize static data. So we can use it to initialize
the mask field of a ENUM control during its declaration.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since bypass paths aren't part of DAPM streams and we may not have any
DAPM streams there may not be anything that triggers a DAPM sync for
them. Mark all input and output widgets as dirty and then sync to do so
at the end of suspend and resume.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Commit 412312 (ASoC: dapm: Make sure all dapm contexts are updated) means
that any DAPM context being updated will have the bias level automatically
set, including the card. We can't safely do this as the card callbacks are
called for each device context and so the management of the card bias is
more complex. Several multi-component cards rely on this behaviour.
Skip updates during the asynchronous run entirely. We should really do them
in the synchronous section but it's not 100% clear which values to pick as
the different DAPM contexts may have different bias levels.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 412312 (ASoC: dapm: Make sure all dapm contexts are updated)
ensures that we update non-CODEC DAPM contexts but means that if a
CODEC has no set_bias_level() operation it'll not be updated. Fix
that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
Ever since the DAPM performance improvements we've been marking all widgets
as not dirty after each DAPM run. Since _PRE and _POST events aren't part
of the DAPM graph this has rendered them non-functional, they will never be
marked dirty again and thus will never be run again.
Fix this by skipping them when marking widgets as not dirty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@vger.kernel.org
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain. This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.
The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.
[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix following:
sound/soc/soc-dapm.c: In function ‘dapm_clock_event’:
sound/soc/soc-dapm.c:1021:1: warning: control reaches end of non-void function [-Wreturn-type]
Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since we're now relying on DAPM for things like enabling clocks when we
reparent the clocks for widgets we need to either use conditional routes
(which are expensive) or remove routes at runtime. Add a route removal
API to support this use case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If we add a new route at runtime then we'll need to recheck the connections
to the affected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Make sure we set the bias level for all DAPM contexts when
changing level.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Codec shutdown performs a DAPM power sequence that might cause conflicts
and/or race conditions if another stream power event is running simultaneously.
Use card's dapm mutex to protect any potential race condition between them.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
dapm_set_path_status() sets connect incorrectly in the case max > 1 with invert.
In that case, the raw disconnect value should be max, which corresponds to the
userspace value 0.
This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
This patch completes commit 3a9abe8.
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <alsa-devel@alsa-project.org>
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stereo is not yet supported by dapm widgets, so remove stereo code from
snd_soc_dapm_get_volsw(), and warn if stereo controls are detected.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_dapm_put_volsw() sets connect incorrectly in the case max > 1 with
invert. In that case, the raw disconnect value should be max, which corresponds
to the userspace value 0.
This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into for-3.6
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
We may as well print as many errors as we can in one go rather than
requiring developers to iterate through all their typos.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We should only add source widgets to the input list.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Make sure we check the correct path for capture.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds a supply-widget variant for connection to the clock-framework.
This widget-type corresponds to the variant for regulators.
Signed-off-by: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reduce our stack consumption by moving the params off the stack, they
are reasonably large and might be an issue on platforms with small stacks.
Reported-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ackeded-by: Liam Girdwood <lrg@ti.com>
A workaround for an ASUS laptop and a few ASoC changes;
most of the commits are tagged for stable, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=KjOE
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A workaround for an ASUS laptop and a few ASoC changes; most of the
commits are tagged for stable, too."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Improve sequencing of AIF channel enables
ALSA: HDA: Add external mic quirk for Asus Zenbook UX31E
ASoC: fsi: update for dmaengine prep_slave_sg fallout.
ASoC: core: Fix card RTD count for deferred probe.
ASoC: cs42l73: don't use negative array index
ASoC: dapm: Ensure power gets managed for line widgets
This patch allows DPCM to dynamically alter the FE to BE PCM links
at runtime based on mixer setting updates. DAPM is looked up after
every mixer update and we perform a DPCM runtime update if the
mixer has a change of value.
This patchs adds/changes the following :-
o Adds DPCM runtime update core.
o Changes soc_dapm_mixer_update_power() and soc_dapm_mux_update_power()
to return if a change has occured rather than 0. No other users check
atm.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for ASoC DSP support.
Add a DAPM API call to determine whether a DAPM audio path is valid between
source and sink widgets. This also takes into account all kcontrol mux and mixer
settings in between the source and sink widgets to validate the audio path.
This will be used by the DSP core to determine the runtime DAI mappings
between FE and BE DAIs in order to run PCM operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the following build warning:
sound/soc/soc-dapm.c: In function 'snd_soc_dai_link_event':
sound/soc/soc-dapm.c:2913: warning: format '%lx' expects type 'long unsigned int', but argument 3 has type 'u64'
'%llx' should be used with 'u64' type.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having the user half start a stream but avoid any DMA to
trigger data flow on links which don't pass through the CPU create a
DAPM route between the two DAI widgets using a hw_params configuration
provided by the machine driver with the new 'params' member of the
dai_link struct. If no configuration is provided in the dai_link then
use the old style even for CODEC<->CODEC links to avoid breaking
systems.
This greatly simplifies the userspace usage of such links, making them
as simple as analogue connections with the stream configuration being
completely transparent to them.
This is achieved by defining a new dai_link widget type which is created
when CODECs are linked and triggering the configuration of the link via
the normal PCM operations from there. It is expected that the bias
level callbacks will be used for clock configuration.
Currently only the DAI format, rate and channel count can be configured
and currently the only DAI operations which can be called are hw_params
and digital_mute(). This corresponds well to the majority of CODEC
drivers which only use other callbacks for constraint setting but there
is obviously much room for extension here. We can't simply call
hw_params() on startup as things like the system clocking configuration
may change at runtime and in future it will be desirable to offer some
configurability of the link parameters.
At present we are also restricted to a single DAPM link for the entire
DAI. Once we have better support for channel mapping it would also be
desirable to extend this feature so that we can propagate per-channel
power state over the link.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow CODEC<->CODEC links to function we will need to allow
DAPM paths to be created that pass through DAIs rather than only ones
that are source or sunk at the DAI.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
We added locking here but there were a couple error paths where we
forgot to drop the lock before returning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Line widgets had not been included in either the power up or power down
sequences so if a widget had an event associated with it that event would
never be run. Fix this minimally by adding them to the sequences, we
should probably be doing away with the specific widget types as they all
have the same priority anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPgOpXAAoJEHm+PkMAQRiG8eUIAJ3Hjo0o5hqzxol8LWHDGF8s
3h59qwRtts82u2psStZULPLbBzw6yjn8U5Mcrh7pffwCG2BzBL5rXcmXfvoPaET3
TjylIj986Jv+jwZyuyZcLzYyoUtgjtq7hnt4tgVVEPlexYs7LxUl8vO8QjxT+bVO
7eKgzLsXlBC9kw4P5M7kOBQ9NE5vmEcKf+fB3Hu3DqfVJtw9Lb7EeDQj/cbQsGqI
vavSxe7lMTPsgMP2+hRz4txGTDJNRazkO2BdwfYrcNwTSa8tfBFlamww3y4+eJtq
MFQfdNxQpumh2++T4IC2i/nLaawH7kWj2EdaRCRLMy9hVlb/v8/wcgd+1nfLkU8=
=0on9
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc2' into for-3.5
Linux 3.4-rc2 contains some bug fixes we need, including the addition of
an export for regcache_sync_region().
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we're creating widgets for all DAIs there should be no more
need for the bodges we've been carrying for non-DAPM CODEC drivers so
remove them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If we do use regmap then regmap will take care of things for us. We
actually already have this check at a higher level for the current
users but this makes sure we do the right thing in the future too if
we need to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently not all DAPM widget IO ops are holding their component mutex
(codec or platform). Make sure this is now held for DAPM widget IO operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently DAPM widgets use the private data for their regulator.
Add a regulator * for widgets to use instead of private data.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename SND_SOC_DAPM_CLASS_PCM to SND_SOC_DAPM_CLASS_RUNTIME to
better match the usage and align with card mutex too.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently stream events are only perfomed on codec stream widgets only.
There is now a need to be able to perform stream events on platform
widgets too.
e.g. we have the ABE platform driver with several DAI links
to dummy codecs. We need to be able to perform stream events on any
of the dummy codec DAI links.
This patch also removes the snd_soc_dai * parameter since it's already
contained within the rtd * parameter.
Finally makle stream event return void since no one checks it anyway.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both snd_soc_dapm_mux_update_power() and snd_soc_dapm_mixer_update_power() can
be called internally within DAPM core (with DAPM mutex held) and externally.
Provide some wrappers so that external users of both functions do not have to
remember to hold the DAPM mutex.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has now become necessary to use a DAPM mutex instead of the codec
mutex to lock the DAPM operations. This is due to the recent multi
component support and forth coming Dynamic PCM updates.
Currently we lock DAPM operations with the codec mutex of the calling
RTD context. However, DAPM operations can span the whole card context
and all components.
This patch updates the DAPM operations that use the codec mutex to
now use the DAPM mutex PCM subclass for all DAPM ops.
We also add a mutex subclass for DAPM init and PCM operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The widget locking depends on some of the other locking changes which
are queued up for 3.5 not 3.4 so revert the locking changes and reapply
them in 3.5.
This reverts commit 66bf93212f and
96acc357be.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If we do use regmap then regmap will take care of things for us. We
actually already have this check at a higher level for the current
users but this makes sure we do the right thing in the future too if
we need to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently not all DAPM widget IO ops are holding their component mutex
(codec or platform). Make sure this is now held for DAPM widget IO operations.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove printk(KERN_WARNING) and use dev_warn() instead.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Recent enhancements in the bias management means that we might not be
in standby when the CODEC is idle and can have active widgets without
being in full power mode but the shutdown functionality assumes these
things. Add checks for the bias level at each stage so that we don't
do transitions other than the ON->PREPARE->STANDBY->OFF ones that the
drivers are expecting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
This means we don't need to walk through every single widget in the system
for each stream event which is a bit less silly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do smarter things with DAI links create DAPM
widgets which directly represent the DAIs in the DAPM graph. These are
automatically created from the DAIs as we probe the card with references
held in both directions between the widget and the DAI.
The widgets are not made available for direct instantiation by drivers,
they are created automatically from the DAIs. Drivers should be updated
to create stream routes using DAPM maps rather than by annotating AIF
and DAC widgets with streams.
In order to ease transition to this model from existing drivers we
automatically create DAPM routes between the DAI widgets and the existing
stream widgets which are started and stopped by the DAI widgets, though
the old stream handling mechanism is still in place. This also has the
nice effect of removing non-DAPM devices as any device with a DAI
acquires a widget automatically which will allow future simplifications
to the core DAPM logic.
The intention is that in future the AIF and DAI widgets will gain the
ability to interact such that we are able to manage activity on
individual channels independantly rather than powering up and down the
entire AIF as we do currently.
Currently we only generate these for CODECs, mostly as I have no systems
with non-CODEC DAPM to integrate with. It should be a simple matter of
programming to add the additional hookup for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do something smarter than iterate through widgets
doing strcmp() to work out what to power up for stream events change the
interface used to generate them to be based on the combination of a DAI
and a stream direction rather than just a simple string identifying the
stream.
At some point we'll probably want a set of channels too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Let the caller fiddle with the widget after we're done in order to
facilitate further refactoring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Everything now uses snd_soc_dapm_new_controls() instead so we don't need
to make it part of the external API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since the addition of the non-CODEC control adds card controls like the
DAPM pin switch have been broken as they are expecting the private data
for the control to be the CODEC but it's now the card. Fix that for the
pin switches, an audit of other drivers is required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Currently when DAPM widgets are power sequenced the stream_event()
completion callback is only called for the stream_event originator
DAPM context. Other components in the card may also be interested so
make sure they are also notified of any widget power events.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's useful to export the DAPM reset as a static function for future use
by other DAPM functions. e.g. The dynamic PCM query widgets resets the DAPM
graph before working out active paths.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix some spelling mistakes in the header and remove the todo items. Most
todo items are now available as kcontrol options now anyway.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow for the operation of custom mixer and mux DAPM widgets that can call
snd_soc_dapm_mixer_update_power() and snd_soc_dapm_mux_update_power() directly
after updating their status. This is useful with complex DAPM Mixer operations
where we need to do additional work in addition to setting a few mixer register
bits.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator has no power control itself and so shouldn't cause a
power up of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care if any action is taken immediately so let the PM
core defer things if it wants to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modern devices allow systems to enable and disable individual supplies on
the device, allowing additional power saving by switching off regulators
which power portions of the device which are not currently in use. Add a
new SND_SOC_DAPM_REGULATOR_SUPPLY widget type factoring out the code for
managing such widgets from individual drivers.
The widget name will be used as the supply name when requesting the
regulator from the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes a NULL pointer dereference in dapm_power_widgets() if the dapm context
has no codec.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The device model needs a release() function so it can free devices when
they become dereferenced. Do that for rtds.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As for PCMs take a runtime power management reference to devices that are
in a non-off bias, avoiding the need to do this in individual drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator behaves as an input would but is not considered for
any of the special behaviour associated with external input pins. This
is especially useful when automatically working out not connected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This makes the output a bit less confusing on multi-CODEC systems as the
same pin may appear in multiple CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A card is fully routed if the DAPM route table describes all connections on
the board.
When a card is fully routed, some operations can be automated by the ASoC
core. The first, and currently only, such operation is described below, and
implemented by this patch.
Codecs often have a large number of external pins, and not all of these pins
will be connected on all board designs. Some machine drivers therefore call
snd_soc_dapm_nc_pin() for all the unused pins, in order to tell the ASoC core
never to activate them.
However, when a card is fully routed, the information needed to derive the
set of unused pins is present in card->dapm_routes. In this case, have
the ASoC core automatically call snd_soc_dapm_nc_pin() for each unused
codec pin.
This has been tested with soc/tegra/tegra_wm8903.c and soc/tegra/trimslice.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We really should be doing this in the core, not in a driver...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
The number of connected input and output endpoints for a given widgets
can't change during a DAPM run so there is no need to redo the recursion
through branches of the tree we've already visited. Doing this on one of
my test systems gives an improvement of:
Power Path Neighbour
Before: 63 607 731
After: 63 141 181
which scales up well as more widgets are involved in paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This ensures none of the rest of the code ever encounters a widget which
does not have a power check function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we only have one sync during the initial startup of the card by
making snd_soc_dapm_sync() a noop on non-instantiated cards. This avoids
any bounces due to things like jacks reporting their initial state on
partially initialised cards. The callers that don't also get called at
runtime should just be removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care how many widgets a supply is supplying, we just care
if the number is non-zero. This didn't actually produce any improvement
in the test cases I've been using but seems obviously sensible enough that
I'm pushing it out anyway.
We could do a similar thing for other widgets but this may be unhelpful
for further refactorings Liam was working on aiming to allow us to
identify connected audio paths.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The whole point of supply widgets is that they aren't inputs to their
sinks so a state change in a supply should never affect the state of the
widget being supplied and we don't need to mark them as dirty.
Power Path Neighbour
Before: 69 727 905
After: 63 607 731
This is particularly useful where supplies affect large portions of the
chip (eg, a bandgap supplying the analogue sections).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some widgets will get power_check() run on them more than once during a
DAPM run, most commonly due to supply widgets checking to see if their
consumers are powered up. It's wasteful to do this so cache the result
of power_check() during a run. For one system I tested this on I got an
improvement of:
Power Path Neighbour
Before: 106 970 1186
After: 69 727 905
from this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Help diagnose why we're checking widgets by providing some logging when
we first dirty them. This should possibly be a trace point if it's useful
but can be absurdly verbose if enabled, we can always change it later if
desired.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If two widgets are not currently connected then there is no need to
propagate a power state change between them as we mark the affected
widgets when we change a connection. Similarly if a neighbour widget is
already in the state being set for the current widget then there is no
need to recheck.
On one system I tested this gave:
Power Path Neighbour
Before: 114 1066 1327
After: 106 970 1186
which is an improvement, although relatively small.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to reduce the number of DAPM power checks we run keep a list of
widgets which have been changed since the last DAPM run and iterate over
that rather than the full widget list. Whenever we change the power state
for a widget we add all the source and sink widgets it has to the dirty
list, ensuring that all widgets in the path are checked.
This covers more widgets than we need to as some of the neighbour widgets
won't be connected but it's simpler as a first step. On one system I tried
this gave:
Power Path Neighbour
Before: 207 1939 2461
After: 114 1066 1327
which seems useful.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We're not actually doing any dynamic power management based on connection
and output drivers (which are pretty much the same thing) are marked as
unconditionally connected already.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We've got the same code in two different places, let's have it in a single
place instead.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Future patches will try to reduce the number of widgets we check on each
DAPM run but we're still going to need to look and see if the devices is
on at all so we can manage the overall device bias. Move these checks out
into the main dapm_power_widgets() function so we don't have to think about
them for now.
Once we're doing more incremental updates it'll probably be worth using
refcounts for each bias level to avoid having to do the sweep over all
widgets but that's not going to be where the big performance wins are.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Split the decision about what the new power should be out from the
implementation of that decision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently we force all devices in the system to be at the same bias level.
This is due to concerns about power or pop/click impacts from either
ramping VMID or mismatching VMID on the analogue I/O lines between
connected devices but does mean we power devices up more often than we
really need to.
If a device flags idle_bias_off this will usually mean that it's either
all digital or ground referenced (in which case the idle and powered bias
levels are identical) so this concern does not apply and we can save some
power by leaving it off when not needed itself.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The number of times we look at a potentially connected neighbour is just
as important as the number of times we actually recurse into looking at
that neighbour so also collect that statistic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The indentation is getting a little deep. Should be straight code motion,
no functional changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the longest standing areas for improvement in ASoC has been the
DAPM algorithm - it repeats the same checks many times whenever it is run
and makes no effort to limit the areas of the graph it checks meaning we
do an awful lot of walks over the full graph. This has never mattered too
much as the size of the graph has generally been small in relation to the
size of the devices supported and the speed of CPUs but it is annoying.
In preparation for work on improving this insert a trace point after the
graph walk has been done. This gives us specific timing information for
the walk, and in order to give quantifiable (non-benchmark) numbers also
count every time we check a link or check the power for a widget and report
those numbers. Substantial changes in the algorithm may require tweaks to
the stats but they should be useful for simpler things.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have dapm_context instead of codec parameter.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
