Limit the size of the struct blk_zone array used in
blk_revalidate_disk_zones() to avoid memory allocation failures leading
to disk revalidation failure. Also further reduce the likelyhood of
such failures by using kvcalloc() (that is vmalloc()) instead of
allocating contiguous pages with alloc_pages().
Fixes: 515ce60613 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation")
Fixes: e76239a374 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
During disk scan and revalidation done with sd_revalidate(), the zones
of a zoned disk are checked using the helper function
blk_revalidate_disk_zones() if a configuration change is detected
(change in the number of zones or zone size). The function
blk_revalidate_disk_zones() issues report_zones calls that are very
large, that is, to obtain zone information for all zones of the disk
with a single command. The size of the report zones command buffer
necessary for such large request generally is lower than the disk
max_hw_sectors and KMALLOC_MAX_SIZE (4MB) and succeeds on boot (no
memory fragmentation), but often fail at run time (e.g. hot-plug
event). This causes the disk revalidation to fail and the disk
capacity to be changed to 0.
This problem can be avoided by using vmalloc() instead of kmalloc() for
the buffer allocation. To limit the amount of memory to be allocated,
this patch also introduces the arbitrary SD_ZBC_REPORT_MAX_ZONES
maximum number of zones to report with a single report zones command.
This limit may be lowered further to satisfy the disk max_hw_sectors
limit. Finally, to ensure that the vmalloc-ed buffer can always be
mapped in a request, the buffer size is further limited to at most
queue_max_segments() pages, allowing successful mapping of the buffer
even in the worst case scenario where none of the buffer pages are
contiguous.
Fixes: 515ce60613 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation")
Fixes: e76239a374 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Only GFP_KERNEL and GFP_NOIO are used with blkdev_report_zones(). In
preparation of using vmalloc() for large report buffer and zone array
allocations used by this function, remove its "gfp_t gfp_mask" argument
and rely on the caller context to use memalloc_noio_save/restore() where
necessary (block layer zone revalidation and dm-zoned I/O error path).
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To allow the SCSI subsystem scsi_execute_req() function to issue
requests using large buffers that are better allocated with vmalloc()
rather than kmalloc(), modify bio_map_kern() to allow passing a buffer
allocated with vmalloc().
To do so, detect vmalloc-ed buffers using is_vmalloc_addr(). For
vmalloc-ed buffers, flush the buffer using flush_kernel_vmap_range(),
use vmalloc_to_page() instead of virt_to_page() to obtain the pages of
the buffer, and invalidate the buffer addresses with
invalidate_kernel_vmap_range() on completion of read BIOs. This last
point is executed using the function bio_invalidate_vmalloc_pages()
which is defined only if the architecture defines
ARCH_HAS_FLUSH_KERNEL_DCACHE_PAGE, that is, if the architecture
actually needs the invalidation done.
Fixes: 515ce60613 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation")
Fixes: e76239a374 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In bio_integrity_prep(), a kernel buffer is allocated through kmalloc() to
hold integrity metadata. Later on, the buffer will be attached to the bio
structure through bio_integrity_add_page(), which returns the number of
bytes of integrity metadata attached. Due to unexpected situations,
bio_integrity_add_page() may return 0. As a result, bio_integrity_prep()
needs to be terminated with 'false' returned to indicate this error.
However, the allocated kernel buffer is not freed on this execution path,
leading to a memory leak.
To fix this issue, free the allocated buffer before returning from
bio_integrity_prep().
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull NVMe fixes from Christoph:
"Lof of fixes all over the place, and two very minor features that
were in the nvme tree by the end of the merge window, but hadn't made
it out to Jens yet."
* 'nvme-5.3' of git://git.infradead.org/nvme:
nvme: fix regression upon hot device removal and insertion
nvme-fc: fix module unloads while lports still pending
nvme-tcp: don't use sendpage for SLAB pages
nvme-tcp: set the STABLE_WRITES flag when data digests are enabled
nvmet: print a hint while rejecting NSID 0 or 0xffffffff
nvme-multipath: do not select namespaces which are about to be removed
nvme-multipath: also check for a disabled path if there is a single sibling
nvme-multipath: factor out a nvme_path_is_disabled helper
nvme: set physical block size and optimal I/O size
nvme: add I/O characteristics fields
nvmet: export I/O characteristics attributes in Identify
nvme-trace: add delete completion and submission queue to admin cmds tracer
nvme-trace: fix spelling mistake "spcecific" -> "specific"
nvme-pci: limit max_hw_sectors based on the DMA max mapping size
nvme-pci: check for NULL return from pci_alloc_p2pmem()
nvme-pci: don't create a read hctx mapping without read queues
nvme-pci: don't fall back to a 32-bit DMA mask
nvme-pci: make nvme_dev_pm_ops static
nvme-fcloop: resolve warnings on RCU usage and sleep warnings
nvme-fcloop: fix inconsistent lock state warnings
If the device is setup with ioctl we can resize the device after the
initial setup, but if the device is setup with netlink we cannot use the
resize related ioctls and there is no netlink reconfigure size ATTR
handling code.
This patch adds netlink reconfigure resize support to match the ioctl
interface.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This will allow the blksize to be set zero and then use 1024 as
default.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
[fix to use goto out instead of return in genl_connect]
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Simultaneously writing to a sequential zone of a zoned block device
from multiple contexts requires mutual exclusion for BIO issuing to
ensure that writes happen sequentially. However, even for a well
behaved user correctly implementing such synchronization, BIO plugging
may interfere and result in BIOs from the different contextx to be
reordered if plugging is done outside of the mutual exclusion section,
e.g. the plug was started by a function higher in the call chain than
the function issuing BIOs.
Context A Context B
| blk_start_plug()
| ...
| seq_write_zone()
| mutex_lock(zone)
| bio-0->bi_iter.bi_sector = zone->wp
| zone->wp += bio_sectors(bio-0)
| submit_bio(bio-0)
| bio-1->bi_iter.bi_sector = zone->wp
| zone->wp += bio_sectors(bio-1)
| submit_bio(bio-1)
| mutex_unlock(zone)
| return
| -----------------------> | seq_write_zone()
| mutex_lock(zone)
| bio-2->bi_iter.bi_sector = zone->wp
| zone->wp += bio_sectors(bio-2)
| submit_bio(bio-2)
| mutex_unlock(zone)
| <------------------------- |
| blk_finish_plug()
In the above example, despite the mutex synchronization ensuring the
correct BIO issuing order 0, 1, 2, context A BIOs 0 and 1 end up being
issued after BIO 2 of context B, when the plug is released with
blk_finish_plug().
While this problem can be addressed using the blk_flush_plug_list()
function (in the above example, the call must be inserted before the
zone mutex lock is released), a simple generic solution in the block
layer avoid this additional code in all zoned block device user code.
The simple generic solution implemented with this patch is to introduce
the internal helper function blk_mq_plug() to access the current
context plug on BIO submission. This helper returns the current plug
only if the target device is not a zoned block device or if the BIO to
be plugged is not a write operation. Otherwise, the caller context plug
is ignored and NULL returned, resulting is all writes to zoned block
device to never be plugged.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The elevator_name field in struct elevator_type is declared as an array
of characters (ELV_NAME_MAX size) but in practice used as a string
pointer with its initialization done statically within each
elevator elevator_type structure declaration.
Change the declaration of elevator_name to the more appropriate
"const char *" type.
Acked-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ELV_MQUEUE_XXX definitions in include/linux/elevator.h are unused
since the removal of elevator_may_queue_fn in kernel 5.0. Remove these
definitions and also remove the documentation of elevator_may_queue_fn
in Documentiation/block/biodoc.txt.
Acked-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we validate the new controller id, we want to skip
controllers that are either deleting or dead. Fix the check
to do that and not on the newly added controller.
Fixes: 1b1031ca63 ("nvme: validate cntlid during controller initialisation")
Reported-by: Jon Derrick <jonathan.derrick@intel.com>
Tested-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
After commit 991f61fe7e ("Blk-throttle: reduce tail io latency when
iops limit is enforced") wait time could be zero even if group is
throttled and cannot issue requests right now. As a result
throtl_select_dispatch() turns into busy-loop under irq-safe queue
spinlock.
Fix is simple: always round up target time to the next throttle slice.
Fixes: 991f61fe7e ("Blk-throttle: reduce tail io latency when iops limit is enforced")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For large values of the number of zones reported and/or large zone
sizes, the sector increment calculated with
blk_queue_zone_sectors(q) * n
in blk_report_zones() loop can overflow the unsigned int type used for
the calculation as both "n" and blk_queue_zone_sectors() value are
unsigned int. E.g. for a device with 256 MB zones (524288 sectors),
overflow happens with 8192 or more zones reported.
Changing the return type of blk_queue_zone_sectors() to sector_t, fixes
this problem and avoids overflow problem for all other callers of this
helper too. The same change is also applied to the bdev_zone_sectors()
helper.
Fixes: e76239a374 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a shared kthread needs to issue a bio for a cgroup, doing so
synchronously can lead to priority inversions as the kthread can be
trapped waiting for that cgroup. This patch implements
REQ_CGROUP_PUNT flag which makes submit_bio() punt the actual issuing
to a dedicated per-blkcg work item to avoid such priority inversions.
This will be used to fix priority inversions in btrfs compression and
should be generally useful as we grow filesystem support for
comprehensive IO control.
Cc: Chris Mason <clm@fb.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add a helper to determine the target blkcg from wbc.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When writeback IOs are bounced through async layers, the IOs should
only be accounted against the wbc from the original bdi writeback to
avoid confusing cgroup inode ownership arbitration. Add
wbc->no_cgroup_owner to allow disabling wbc cgroup owner accounting.
This will be used make btrfs compression work well with cgroup IO
control.
v2: Renamed from no_wbc_acct to no_cgroup_owner and added comment as
per Jan.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
wbc_account_io() does a very specific job - try to see which cgroup is
actually dirtying an inode and transfer its ownership to the majority
dirtier if needed. The name is too generic and confusing. Let's
rename it to something more specific.
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
btrfs is going to use css_put() and wbc helpers to improve cgroup
writeback support. Add dummy css_get() definition and export wbc
helpers to prepare for module and !CONFIG_CGROUP builds.
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the psi stuff in place we can use the memstall flag to indicate
pressure that happens from throttling.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We discovered a problem in newer kernels where a disconnect of a NBD
device while the flush request was pending would result in a hang. This
is because the blk mq timeout handler does
if (!refcount_inc_not_zero(&rq->ref))
return true;
to determine if it's ok to run the timeout handler for the request.
Flush_rq's don't have a ref count set, so we'd skip running the timeout
handler for this request and it would just sit there in limbo forever.
Fix this by always setting the refcount of any request going through
blk_init_rq() to 1. I tested this with a nbd-server that dropped flush
requests to verify that it hung, and then tested with this patch to
verify I got the timeout as expected and the error handling kicked in.
Thanks,
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Current code allows the module to be unloaded even if there are
pending data structures, such as localports and controllers on
the localports, that have yet to hit their reference counting
to remove them.
Fix by having exit entrypoint explicitly delete every controller,
which in turn will remove references on the remoteports and localports
causing them to be deleted as well. The exit entrypoint, after
initiating the deletes, will wait for the last localport to be deleted
before continuing.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
According to commit a10674bf24 ("tcp: detecting the misuse of
.sendpage for Slab objects") and previous discussion, tcp_sendpage
should not be used for pages that is managed by SLAB, as SLAB is not
taking page reference counters into consideration.
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There was a few false alarms sighted on target side about wrong data
digest while performing high throughput load to XFS filesystem shared
through NVMoF TCP.
This flag tells the rest of the kernel to ensure that the data buffer
does not change while the write is in flight. It incurs a performance
penalty, so only enable it when it is actually needed, i.e. when we are
calculating data digests.
Although even with this change in place, ext2 users can steel experience
false positives, as ext2 is not respecting this flag. This may be apply
to vfat as well.
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Signed-off-by: Mike Playle <mplayle@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Adding this hint for the sake of convenience.
It was spotted that a few times people spent some time before
understanding what is exactly wrong in configuration process. This
should save a few time in such situations, especially for people who
is not very confident with NVMe requirements.
Signed-off-by: Mikhail Skorzhinskii <mskorzhinskiy@solarflare.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
nvme_ns_remove() will first set the NVME_NS_REMOVING flag before removing
it from the list at the very last step.
So to avoid selecting a namespace in nvme_find_path() which is about to be
removed check the NVME_NS_REMOVING flag, too, when selecting a new path.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When we have a singular list in nvme_round_robin_path() we still
need to check its validity.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Factor our a common helper to check if a path has been disabled
by something other than the per-namespace ANA state.
Signed-off-by: Hannes Reinecke <hare@suse.com>
[hch: split from a bigger patch]
Signed-off-by: Christoph Hellwig <hch@lst.de>
>From the NVMe 1.4 spec:
NSFEAT bit 4 if set to 1: indicates that the fields NPWG, NPWA, NPDG, NPDA,
and NOWS are defined for this namespace and should be used by the host for
I/O optimization;
[ ... ]
Namespace Preferred Write Granularity (NPWG): This field indicates the
smallest recommended write granularity in logical blocks for this namespace.
This is a 0's based value. The size indicated should be less than or equal
to Maximum Data Transfer Size (MDTS) that is specified in units of minimum
memory page size. The value of this field may change if the namespace is
reformatted. The size should be a multiple of Namespace Preferred Write
Alignment (NPWA). Refer to section 8.25 for how this field is utilized to
improve performance and endurance.
[ ... ]
Each Write, Write Uncorrectable, or Write Zeroes commands should address a
multiple of Namespace Preferred Write Granularity (NPWG) (refer to Figure
245) and Stream Write Size (SWS) (refer to Figure 515) logical blocks (as
expressed in the NLB field), and the SLBA field of the command should be
aligned to Namespace Preferred Write Alignment (NPWA) (refer to Figure 245)
for best performance.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Several new fields have been introduced in version 1.4 of the NVMe spec
at offsets that were defined as reserved in version 1.3d of the NVMe
spec. Update the definition of the nvme_id_ns data structure such that
it is in sync with version 1.4 of the NVMe spec. This change preserves
backwards compatibility.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make the NVMe NAWUN, NAWUPF, NACWU, NPWG, NPWA, NPDG and NOWS attributes
available to initator systems for the block backend.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are two spelling mistakes in trace_seq_printf messages, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When running a NVMe device that is attached to a addressing
challenged PCIe root port that requires bounce buffering, our
request sizes can easily overflow the swiotlb bounce buffer
size. Limit the maximum I/O size to the limit exposed by
the DMA mapping subsystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Tested-by: Atish Patra <Atish.Patra@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Modify nvme_alloc_sq_cmds() to call pci_free_p2pmem() to free the memory
it allocated using pci_alloc_p2pmem() in case pci_p2pmem_virt_to_bus()
returns null.
Makes sure not to call pci_free_p2pmem() if pci_alloc_p2pmem() returned
NULL, which can happen if CONFIG_PCI_P2PDMA is not configured.
The current implementation is not expected to leak since
pci_p2pmem_virt_to_bus() is expected to fail only if pci_alloc_p2pmem()
returns null. However, checking the return value of pci_alloc_p2pmem()
is more explicit.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Only request an IRQ mapping for read queues if at least one read queue
is being allocted, as nvme_pci_map_queues() will later on ignore the
unnecessary mapping request should nvme_dev_add() request such an IRQ
mapping even though no read queues are being allocated. However,
nvme_dev_add() can avoid making the request by checking the number of
read queues without assuming. This would bring it more in line with
nvme_setup_irqs() and nvme_calc_irq_sets().
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since Linux 5.0 drivers can safely set the largest DMA mask supported
by the device, and don't need fallbacks to work around the dma mapping
implementations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Fix sparse warning:
drivers/nvme/host/pci.c:2926:25: warning:
symbol 'nvme_dev_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
With additional debugging enabled, seeing warnings for suspicious RCU
usage or Sleeping function called from invalid context.
These both map to allocation of a work structure which is currently
GFP_KERNEL, meaning it can sleep. For the RCU warning, the sequence was
sleeping while holding the RCU lock.
Convert the allocation to GFP_ATOMIC.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
With extra debug on, inconsistent lock state warnings are being called
out as the tfcp_req->reqlock is being taken out without irq, while some
calling sequences have the sequence in a softirq state.
Change the lock taking/release to raise/drop irq.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
-----BEGIN PGP SIGNATURE-----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=nbLD
-----END PGP SIGNATURE-----
Merge tag 'for-5.3/libata-20190708' of git://git.kernel.dk/linux-block
Pull libata updates from Jens Axboe:
"These are the changes that are reviewed, tested, and queued up for
this merge window. This contains:
- Removal of redundant memset after dmam_alloc_coherent (Fuqian)
- Expand blacklist check for ST1000LM024, making it independent of
firmware version (Hans)
- Request sense fix (Tejun)
- ahci_sunxi FIFO fix (Uenal)"
* tag 'for-5.3/libata-20190708' of git://git.kernel.dk/linux-block:
drivers: ata: ahci_sunxi: Increased SATA/AHCI DMA TX/RX FIFOs
libata: Drop firmware version check from the ST1000LM024 quirk
ata: sata_sil24: Remove call to memset after dmam_alloc_coherent
ata:sata_qstor: Remove call to memset after dmam_alloc_coherent
ata: sata_nv: Remove call to memset after dmam_alloc_coherent
ata: pdc_adma: Remove call to memset after dmam_alloc_coherent
ata: libahci: Remove call to memset after dmam_alloc_coherent
ata: acard-ahci: Remove call to memset after dmam_alloc_coherent
libata: don't request sense data on !ZAC ATA devices
-----BEGIN PGP SIGNATURE-----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=VSYT
-----END PGP SIGNATURE-----
Merge tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main block updates for 5.3. Nothing earth shattering or
major in here, just fixes, additions, and improvements all over the
map. This contains:
- Series of documentation fixes (Bart)
- Optimization of the blk-mq ctx get/put (Bart)
- null_blk removal race condition fix (Bob)
- req/bio_op() cleanups (Chaitanya)
- Series cleaning up the segment accounting, and request/bio mapping
(Christoph)
- Series cleaning up the page getting/putting for bios (Christoph)
- block cgroup cleanups and moving it to where it is used (Christoph)
- block cgroup fixes (Tejun)
- Series of fixes and improvements to bcache, most notably a write
deadlock fix (Coly)
- blk-iolatency STS_AGAIN and accounting fixes (Dennis)
- Series of improvements and fixes to BFQ (Douglas, Paolo)
- debugfs_create() return value check removal for drbd (Greg)
- Use struct_size(), where appropriate (Gustavo)
- Two lighnvm fixes (Heiner, Geert)
- MD fixes, including a read balance and corruption fix (Guoqing,
Marcos, Xiao, Yufen)
- block opal shadow mbr additions (Jonas, Revanth)
- sbitmap compare-and-exhange improvemnts (Pavel)
- Fix for potential bio->bi_size overflow (Ming)
- NVMe pull requests:
- improved PCIe suspent support (Keith Busch)
- error injection support for the admin queue (Akinobu Mita)
- Fibre Channel discovery improvements (James Smart)
- tracing improvements including nvmetc tracing support (Minwoo Im)
- misc fixes and cleanups (Anton Eidelman, Minwoo Im, Chaitanya
Kulkarni)"
- Various little fixes and improvements to drivers and core"
* tag 'for-5.3/block-20190708' of git://git.kernel.dk/linux-block: (153 commits)
blk-iolatency: fix STS_AGAIN handling
block: nr_phys_segments needs to be zero for REQ_OP_WRITE_ZEROES
blk-mq: simplify blk_mq_make_request()
blk-mq: remove blk_mq_put_ctx()
sbitmap: Replace cmpxchg with xchg
block: fix .bi_size overflow
block: sed-opal: check size of shadow mbr
block: sed-opal: ioctl for writing to shadow mbr
block: sed-opal: add ioctl for done-mark of shadow mbr
block: never take page references for ITER_BVEC
direct-io: use bio_release_pages in dio_bio_complete
block_dev: use bio_release_pages in bio_unmap_user
block_dev: use bio_release_pages in blkdev_bio_end_io
iomap: use bio_release_pages in iomap_dio_bio_end_io
block: use bio_release_pages in bio_map_user_iov
block: use bio_release_pages in bio_unmap_user
block: optionally mark pages dirty in bio_release_pages
block: move the BIO_NO_PAGE_REF check into bio_release_pages
block: skd_main.c: Remove call to memset after dma_alloc_coherent
block: mtip32xx: Remove call to memset after dma_alloc_coherent
...
- Add helpers to count items in a property array (Andy Shevchenko).
- Extend "software nodes" support to be more convenient for
representing device properties supplied by drivers (Heikki
Krogerus).
- Add device_find_child_by_name() helper to the driver core (Heikki
Krogerus).
- Extend device connection code to also look for references provided
via fwnode pointers (Heikki Krogerus).
- Start to register proper struct device objects for USB Type-C
muxes and orientation switches (Heikki Krogerus).
- Update the intel_cht_int33fe driver to describe devices in a more
general way with the help of "software nodes" (Heikki Krogerus).
-----BEGIN PGP SIGNATURE-----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=jOFk
-----END PGP SIGNATURE-----
Merge tag 'devprop-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These add helpers for counting items in a property array and extend
the "software nodes" support to be more convenient for representing
device properties supplied by drivers and make the intel_cht_int33fe
driver use that.
Specifics:
- Add helpers to count items in a property array (Andy Shevchenko).
- Extend "software nodes" support to be more convenient for
representing device properties supplied by drivers (Heikki
Krogerus).
- Add device_find_child_by_name() helper to the driver core (Heikki
Krogerus).
- Extend device connection code to also look for references provided
via fwnode pointers (Heikki Krogerus).
- Start to register proper struct device objects for USB Type-C muxes
and orientation switches (Heikki Krogerus).
- Update the intel_cht_int33fe driver to describe devices in a more
general way with the help of "software nodes" (Heikki Krogerus)"
* tag 'devprop-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add helpers to count items in an array
platform/x86: intel_cht_int33fe: Replacing the old connections with references
platform/x86: intel_cht_int33fe: Supply fwnodes for the external dependencies
platform/x86: intel_cht_int33fe: Provide fwnode for the USB connector
platform/x86: intel_cht_int33fe: Provide software nodes for the devices
platform/x86: intel_cht_int33fe: Remove unused fusb302 device property
platform/x86: intel_cht_int33fe: Register max17047 in its own function
usb: typec: Registering real device entries for the muxes
device connection: Find connections also by checking the references
device property: Introduce fwnode_find_reference()
ACPI / property: Don't limit named child node matching to data nodes
driver core: Add helper device_find_child_by_name()
software node: Add software_node_get_reference_args()
software node: Use kobject name when finding child nodes by name
software node: Add support for static node descriptors
software node: Simplify software_node_release() function
software node: Allow node creation without properties
- Update the ACPICA code in the kernel to upstream revision 20190703
including:
* Initial/defalut namespace creation simplification (Bob Moore).
* Object initialization sequence update (Bob Moore).
* Removal of legacy module-level (dead) code (Erik Schmauss).
* Table load object initialization update (Erik Schmauss, Nikolaus
Voss).
- Fix GPE enabling issue in ACPICA causing premature wakeups from
suspend-to-idle to occur (Rafael Wysocki).
- Allow ACPI AC and battery drivers to be built on non-X86 (Ard
Biesheuvel).
- Fix address space handler removal in the ACPI PMIC driver for
Intel platforms (Andy Shevchenko).
- Allow BGRT to be overridden via initrd or configfs (Andrea Oliveri).
- Fix object resolution on table loads via configfs (Nikolaus Voss).
- Clean up assorted pieces of ACPI code and tools (Colin Ian King,
Liguang Zhang, Masahiro Yamada).
- Fix documentation build warning, convert the extcon document to
ReST and add it to the ACPI documentation (Mauro Carvalho Chehab,
Qian Cai).
-----BEGIN PGP SIGNATURE-----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=4FCz
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20190703, fix up the handling of GPEs in ACPICA, allow some more ACPI
code to be built on ARM64 platforms, allow BGRT to be overridden, fix
minor issues and clean up assorted pieces of ACPI code.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20190703
including:
- Initial/default namespace creation simplification (Bob Moore).
- Object initialization sequence update (Bob Moore).
- Removal of legacy module-level (dead) code (Erik Schmauss).
- Table load object initialization update (Erik Schmauss,
Nikolaus Voss).
- Fix GPE enabling issue in ACPICA causing premature wakeups from
suspend-to-idle to occur (Rafael Wysocki).
- Allow ACPI AC and battery drivers to be built on non-X86 (Ard
Biesheuvel).
- Fix address space handler removal in the ACPI PMIC driver for Intel
platforms (Andy Shevchenko).
- Allow BGRT to be overridden via initrd or configfs (Andrea
Oliveri).
- Fix object resolution on table loads via configfs (Nikolaus Voss).
- Clean up assorted pieces of ACPI code and tools (Colin Ian King,
Liguang Zhang, Masahiro Yamada).
- Fix documentation build warning, convert the extcon document to
ReST and add it to the ACPI documentation (Mauro Carvalho Chehab,
Qian Cai)"
* tag 'acpi-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / APEI: Remove needless __ghes_check_estatus() calls
ACPICA: Update version to 20190703
ACPICA: Update table load object initialization
ACPICA: Update for object initialization sequence
ACPICA: remove legacy module-level code due to deprecation
ACPICA: Namespace: simplify creation of the initial/default namespace
ACPI / PMIC: intel: Drop double removal of address space handler
ACPI: APD: remove redundant assignment to pointer clk
docs: extcon: convert it to ReST and move to ACPI dir
ACPI: Make AC and battery drivers available on !X86
ACPICA: Clear status of GPEs on first direct enable
ACPI: configfs: Resolve objects on host-directed table loads
ACPI: tables: Allow BGRT to be overridden
ACPI: OSL: Make a W=1 kernel-doc warning go away
ACPI: tools: Exclude tools/* from .gitignore patterns
- Improve the handling of shared ACPI power resources in the PCI
bus type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec
into account as appropriate and avoid polling devices in D3cold
for PME (Mika Westerberg).
- Fix some corner case issues in ACPI device power management and
in the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210,
and armada-37xx cpufreq drivers (David Arcari, Florian Fainelli,
Paweł Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black).
-----BEGIN PGP SIGNATURE-----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=aBN3
-----END PGP SIGNATURE-----
Merge tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update PCI and ACPI power management (improved handling of ACPI
power resources and PCIe link delays, fixes related to corner cases,
hibernation handling rework), fix and extend the operating performance
points (OPP) framework, add new cpufreq drivers for Raspberry Pi and
imx8m chips, update some other cpufreq drivers, clean up assorted
pieces of PM code and documentation and update tools.
Specifics:
- Improve the handling of shared ACPI power resources in the PCI bus
type layer (Mika Westerberg).
- Make the PCI layer take link delays required by the PCIe spec into
account as appropriate and avoid polling devices in D3cold for PME
(Mika Westerberg).
- Fix some corner case issues in ACPI device power management and in
the PCI bus type layer, optimiza and clean up the handling of
runtime-suspended PCI devices during system-wide transitions to
sleep states (Rafael Wysocki).
- Rework hibernation handling in the ACPI core and the PCI bus type
to resume runtime-suspended devices before hibernation (which
allows some functional problems to be avoided) and fix some ACPI
power management issues related to hiberation (Rafael Wysocki).
- Extend the operating performance points (OPP) framework to support
a wider range of devices (Rajendra Nayak, Stehpen Boyd).
- Fix issues related to genpd_virt_devs and issues with platforms
using the set_opp() callback in the OPP framework (Viresh Kumar,
Dmitry Osipenko).
- Add new cpufreq driver for Raspberry Pi (Nicolas Saenz Julienne).
- Add new cpufreq driver for imx8m and imx7d chips (Leonard Crestez).
- Fix and clean up the pcc-cpufreq, brcmstb-avs-cpufreq, s5pv210, and
armada-37xx cpufreq drivers (David Arcari, Florian Fainelli, Paweł
Chmiel, YueHaibing).
- Clean up and fix the cpufreq core (Viresh Kumar, Daniel Lezcano).
- Fix minor issue in the ACPI system sleep support code and export
one function from it (Lenny Szubowicz, Dexuan Cui).
- Clean up assorted pieces of PM code and documentation (Kefeng Wang,
Andy Shevchenko, Bart Van Assche, Greg Kroah-Hartman, Fuqian Huang,
Geert Uytterhoeven, Mathieu Malaterre, Rafael Wysocki).
- Update the pm-graph utility to v5.4 (Todd Brandt).
- Fix and clean up the cpupower utility (Abhishek Goel, Nick Black)"
* tag 'pm-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (57 commits)
ACPI: PM: Make acpi_sleep_state_supported() non-static
PM: sleep: Drop dev_pm_skip_next_resume_phases()
ACPI: PM: Unexport acpi_device_get_power()
Documentation: ABI: power: Add missing newline at end of file
ACPI: PM: Drop unused function and function header
ACPI: PM: Introduce "poweroff" callbacks for ACPI PM domain and LPSS
ACPI: PM: Simplify and fix PM domain hibernation callbacks
PCI: PM: Simplify bus-level hibernation callbacks
PM: ACPI/PCI: Resume all devices during hibernation
cpufreq: Avoid calling cpufreq_verify_current_freq() from handle_update()
cpufreq: Consolidate cpufreq_update_current_freq() and __cpufreq_get()
kernel: power: swap: use kzalloc() instead of kmalloc() followed by memset()
cpufreq: Don't skip frequency validation for has_target() drivers
PCI: PM/ACPI: Refresh all stale power state data in pci_pm_complete()
PCI / ACPI: Add _PR0 dependent devices
ACPI / PM: Introduce concept of a _PR0 dependent device
PCI / ACPI: Use cached ACPI device state to get PCI device power state
ACPI: PM: Allow transitions to D0 to occur in special cases
ACPI: PM: Avoid evaluating _PS3 on transitions from D3hot to D3cold
cpufreq: Use has_target() instead of !setpolicy
...
Many updates in this development cycle are found in ASoC where it got
a wide range of changes for the continued refactoring.
Some highlights are below.
ASoC:
* Continued refactoring work by Morimoto-san toward the full
componentization; the changes are seen allover the places
* Support for force disconnecting muxes in DAPM
* Continued development of ASoC Intel SOF stuff
* New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90,
Conexant CX2072X, Realtek RT1011 and RT1308
HD-audio:
* More fixes and adjustments for ASoC SOF HD-audio
* Fix for resume problem on some Realtek codecs
USB-audio:
* A few fixes for the issues reported by syzbot USB fuzzer
* Fix for UAC2 extension unit parser
* Quirks for Line6 Helix, Emgaic Unitor 8
FireWire:
* Lots of code refactoring and fixes in most of its components
-----BEGIN PGP SIGNATURE-----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=H+RV
-----END PGP SIGNATURE-----
Merge tag 'sound-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Many updates in this development cycle are found in ASoC where it got
a wide range of changes for the continued refactoring.
Some highlights are below.
ASoC:
- Continued refactoring work by Morimoto-san toward the full
componentization; the changes are seen allover the places
- Support for force disconnecting muxes in DAPM
- Continued development of ASoC Intel SOF stuff
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308
HD-audio:
- More fixes and adjustments for ASoC SOF HD-audio
- Fix for resume problem on some Realtek codecs
USB-audio:
- A few fixes for the issues reported by syzbot USB fuzzer
- Fix for UAC2 extension unit parser
- Quirks for Line6 Helix, Emgaic Unitor 8
FireWire:
- Lots of code refactoring and fixes in most of its components"
* tag 'sound-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (626 commits)
ALSA: firewire-lib: code refactoring for local variables
ALSA: firewire-lib: code refactoring for post operation to data block counter
ALSA: firewire-lib: code refactoring for error path of parser for CIP header
ALSA: firewire-lib: fix different data block counter between probed event and transferred isochronous packet
ALSA: firewire-lib: fix initial value of data block count for IR context without CIP_DBC_IS_END_EVENT
ALSA: firewire-lib/fireface: fix initial value of data block counter for IR context with CIP_NO_HEADER
ALSA: firewire-lib: fix invalid length of rx packet payload for tracepoint events
ALSA: usb-audio: fix Line6 Helix audio format rates
firewire-motu: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: firewire-digi00x: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: dice: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: oxfw: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: fireworks: fix wrong reference count for stream functionality at error path of rawmidi interface
ALSA: bebob: fix wrong reference count for stream functionality at error path of rawmidi interface
ASoC: SOF: Intel: implement runtime idle for CNL/APL
ASoC: SOF: add runtime idle callback
ASoC: hdac_hdmi: report codec link up/down status to bus
ASoC: SOF: debug: fix possible memory leak in sof_dfsentry_write()
ASoC: sunxi: sun50i-codec-analog: Add earpiece
ASoC: rt5665: remove redundant assignment to variable idx
...
- remove fbdev notifier usage for fbcon (as prep work to clean up the fbcon
locking), add locking checks in vt/console code and make assorted cleanups
in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb, pvr2fb and
pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph Hellwig)
- add check for new BGRT status field rotation bits in efifb driver (Hans de
Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R. Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W1AD
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v5.3' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- remove fbdev notifier usage for fbcon (as prep work to clean up the
fbcon locking), add locking checks in vt/console code and make
assorted cleanups in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb,
pvr2fb and pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph
Hellwig)
- add check for new BGRT status field rotation bits in efifb driver
(Hans de Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R.
Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio
Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
* tag 'fbdev-v5.3' of git://github.com/bzolnier/linux: (62 commits)
video: fbdev: imxfb: fix a typo in imxfb_probe()
video: fbdev: s3c-fb: Mark expected switch fall-throughs
video: fbdev: s3c-fb: fix sparse warnings about using incorrect types
video: fbdev: don't print error message on framebuffer_alloc() failure
video: fbdev: intelfb: return -ENOMEM on framebuffer_alloc() failure
video: fbdev: s3c-fb: return -ENOMEM on framebuffer_alloc() failure
vga_switcheroo: Depend upon fbcon being built-in, if enabled
video: fbdev: omap2: remove rfbi
video: fbdev: atmel_lcdfb: remove redundant initialization to variable ret
video: fbdev-MMP: Use struct_size() in devm_kzalloc()
video: fbdev: controlfb: fix warnings about comparing pointer to 0
efifb: BGRT: Add check for new BGRT status field rotation bits
jz4740_fb: fix DMA API abuse
video: fbdev: pvr2fb: fix link error for pvr2fb_pci_exit
video: fbdev: s3c-fb: add COMPILE_TEST support
video: fbdev: imxfb: fix sparse warnings about using incorrect types
video: fbdev: pvr2fb: fix build warning when compiling as module
fbcon: Export fbcon_update_vcs
backlight: simplify lcd notifier
staging/olpc_dcon: Add drm conversion to TODO
...
-----BEGIN PGP SIGNATURE-----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=ABgl
-----END PGP SIGNATURE-----
Merge tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Atmel microship ISC driver
- coda has gained support for mpeg2 and mpeg4
- cxusb gained support for analog TV
- rockchip staging driver was split into two separate staging drivers
- added a new staging driver for Allegro DVT video IP core
- added a new staging driver for Amlogic Meson video decoder
- lots of improvements and cleanups
* tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (398 commits)
media: allegro: use new v4l2_m2m_ioctl_try_encoder_cmd funcs
media: doc-rst: Fix typos
media: radio-raremono: change devm_k*alloc to k*alloc
media: stv0297: fix frequency range limit
media: rc: Prefer KEY_NUMERIC_* for number buttons on remotes
media: dvb_frontend: split dvb_frontend_handle_ioctl function
media: mceusb: disable "nonsensical irdata" messages
media: rc: remove redundant dev_err message
media: cec-notifier: add new notifier functions
media: cec: add struct cec_connector_info support
media: cec-notifier: rename variables, check kstrdup and n->conn_name
media: MAINTAINERS: Add maintainers for Media Controller
media: staging: media: tegra-vde: Defer dmabuf's unmapping
media: staging: media: tegra-vde: Add IOMMU support
media: hdpvr: fix locking and a missing msleep
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
media: atmel: atmel-isc: fix i386 build error
media: v4l2-ctrl: Move compound control initialization
media: hantro: Use vb2_get_buffer
media: pci: cx88: Change the type of 'missed' to u64
...
-----BEGIN PGP SIGNATURE-----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=5hCV
-----END PGP SIGNATURE-----
Merge tag 'please-pull-for_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Tony Luck:
"All the bits that Boris had queued in his tree plus four patches to
add support for Intel Icelake Xeon and then fix a few corner cases"
* tag 'please-pull-for_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC: Fix global-out-of-bounds write when setting edac_mc_poll_msec
EDAC, skx, i10nm: Fix source ID register offset
EDAC, i10nm: Check ECC enabling status per channel
EDAC, i10nm: Add Intel additional Ice-Lake support
EDAC: Make edac_debugfs_create_x*() return void
EDAC/aspeed: Remove set but not used variable 'np'
EDAC/ie31200: Reformat PCI device table
EDAC/ie31200: Add Intel Coffee Lake CPU support
EDAC/sifive: Add EDAC platform driver for SiFive SoCs
EDAC/sb_edac: Remove redundant update of tad_base
arm64: dts: stratix10: Add SDMMC EDAC node
EDAC/altera: Add Stratix10 SDMMC support
arm64: dts: stratix10: Add OCRAM EDAC node
EDAC/altera: Add Stratix10 OCRAM ECC support
EDAC/sysfs: Drop device references properly
EDAC/sysfs: Fix memory leak when creating a csrow object
