Use an ELF HWCAP flag to indicate to the process that the CPU provides LL/SC
equivalent atomic operations unit support in addition to BSET/BCLR.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The AM34 processor has an atomic operation that's the equivalent of LL/SC on
other architectures. However, rather than being done through a pair of
instructions, it's driven by writing to a pair of memory-mapped CPU control
registers.
One set of these registers (AARU/ADRU/ASRU) is available for use by userspace,
but for userspace to access them a PTE must be set up to cover the region.
This is done by dedicating the first vmalloc region page to this purpose,
setting the permissions on its PTE such that userspace can access the page.
glibc is hardcoded to expect the registers to be there.
The way atomic ops are done through these registers is straightforward:
(1) Write the address of the word you wish to access into AARU. This causes
the CPU to go and fetch that word and load it into ADRU. The status bits
are also cleared in ASRU.
(2) The current data value is read from the ADRU register and modified.
(3) To alter the data in RAM, the revised data is written back to the ADRU
register, which causes the CPU to attempt to write it back.
(4) The ASRU.RW flag (ASRU read watch), ASRU.LW flag (bus lock watch),
ASRU.IW (interrupt watch) and the ASRU.BW (bus error watch) flags then
must be checked to confirm that the operation wasn't aborted. If any of
the watches have been set to true, the operation was aborted.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement the Panasonic MN10300 AM34 CPU subarch and implement SMP support for
MN10300. Also implement support for the MN2WS0060 processor and the ASB2364
evaluation board which are AM34 based.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the settings of interrupt priorities used by various services configurable
at run time.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Optimise do_csum() to gang up the loads so they're less likely to get
interruptions between.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement atomic ops using the atomic ops unit available in the AM34 CPU. This
allows the equivalent of the LL/SC instructions to be found on other CPUs.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the FPU operate in non-lazy mode under SMP so that when the process that
is currently using the FPU migrates to a different CPU, we don't have to ping
its previous CPU to flush the FPU context.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement global TLB flushing for MN10300. This will be used by the AM34 which
is SMP capable.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Use the [ID]PTEL2 registers rather than [ID]PTEL for TLB control as the bits
are a more suitable layout.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make controllable the use of the PIDR register to mark TLB entries as belonging
to particular processes.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Rename __flush_tlb*() to local_flush_tlb*() as it's more appropriate, and ready
to differentiate local from global TLB flushes when SMP is introduced.
Whilst we're at it, get rid of __flush_tlb_global() and make
local_flush_tlb_page() take an mm_struct pointer rather than VMA pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
An AM34 erratum requires MMUCTR read and write on entry to certain exceptions,
prior to EPSW.NMID being cleared to allow NMIs to happen.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the boot wrapper able to use writeback caching, including flushing the
cache before jumping to the main kernel.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Implement SMP global cache flushing for MN10300. This will be used by the AM34
which is SMP capable.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The AM34 CPU core provides an automated way of purging the cache rather than
manually iterating over all the tags in the cache. Make it possible to use
these.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Differentiate local cache flushing from global cache flushing so that they can
be done differently on SMP systems.
Rename the cache functions from:
mn10300_[id]cache_*()
to:
mn10300_[id]_localcache_*()
and on a UP system, assign the global labels to the local labels.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The functions that perform cache flushing should take addresses of unsigned
long type, not unsigned int.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The current cache flush and invalidate routines operate by controlling the
cache tag registers. Rename the files and add config items to select them.
This makes it easier to support the use of other cache flush methods instead,
such as the use of AM34's area purge registers, if available.
Signed-off-by: David Howells <dhowells@redhat.com>
Reorder asm/cacheflush.h to put arch primitives first, before the main
functions so that the main functions can be inline asm rather than #defines
when non-trivial.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide a MN10300_CACHE_ENABLED config option as inverted logic of
MN10300_CACHE_DISABLED to make things simpler.
Signed-off-by: David Howells <dhowells@redhat.com>
Remove the monitor trap function and the set_jtag_stub function as they're not
really necessary.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Add CPU register declarations for the AM34 subarch.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Don't hard code the cacheline size in the cache control register definitions.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Move the DMA engine control register definitions to the MN103E010 processor
directory so that the MN2WS0050 processor can have its own.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Differentiate AM33_2 and AM33_3 CPU cores in configuration. The MN103E010
processor contains an AM33_2 core.
Whilst we're at it, prepare for AM34-based stuff by declaring AM34_2 too.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The local_irq_disable() function and co. merely raise the interrupt mask on the
MN10300 arch to exclude normal interrupts. This still lets other, higher
priority maskable interrupts through, such as are used to service gdbstub's
serial port and the MN10300 on-chip serial port virtual FIFOs.
Provide functions to allow the maskable interrupts to be fully disabled, which
will exclude those interrupts.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Don't cast away the volatile in test_bit()'s parameter when we change its type
from const volatile void * so that we can dereference it.
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Prevent cnt32_to_63() from being preempted in sched_clock() because it may
read its internal counter, get preempted, get delayed for more than the half
period of the 'TSC' and then write the internal counter, thus corrupting it.
Whilst some callers of sched_clock() have interrupts disabled or hold
spinlocks, not all do, and so preemption must be held here.
Note that sched_clock() is called from lockdep, but that shouldn't be a problem
because although preempt_disable() calls into lockdep, lockdep has a recursion
counter to deal with this.
Signed-off-by: David Howells <dhowells@redhat.com>
Instead of open-coding pci_find_parent_resource and request_resource,
just call pci_claim_resource.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Change the index to unsigned long in all bitops for [mn10300]
Signed-off-by: Justin Chen <justin.chen@hp.com>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
The percpu allocator cannot handle alignments larger than one
page. Allocate the irq stacks seperately, and only keep the
pointers as percpu data.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tj@kernel.org
LKML-Reference: <1288158182-1753-1-git-send-email-brgerst@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86 has finally arrived in the embedded nightmare and will rapidly
grow SoC platform support in various flavours. So we need a place for
the platform support files. That also allows us to clean up the
dumpground which arch/x86/kernel has become over time.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Presently with hardware counter support disabled the backtrace op never
gets initialized. This is a regression over the previous behaviour, so
simply add it back in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For the backtrace code its assumed that the stack pointer is 32-bits,
which is not the case with the sh64 registers. Use the shared
kernel_stack_pointer() helper to get at the actual register, which
already takes care of the necessary typecasting.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
op_name_from_perf_id() currently returns a local variable, which isn't
terribly productive. As we only handle a single PMU case for now, simply
allocate and free the string from the arch init/exit context and have
op_name_from_perf_id() hand back the cached string.
This also takes UTS_MACHINE in to account, given that we build for
multiple architectures.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that sh64 has grown extended page flag support we finally have a free
bit for _PAGE_SPECIAL. Wire it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that all of the controllers have been fixed up, we can finally select
GENERIC_HARDIRQS_NO_DEPRECATED.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the irq chip is found through the irq_desc, but as this is
going away convert over to an irq_data lookup instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
irq_32.c was updated for the new API, while irq_64.c was overlooked. This
syncs them up and gets things building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The introduction of MAX_PHYSMEM_BITS in to the initial cpuinfo struct
causes a build error when sparsemem is disabled and asm/sparsemem.h is
not brought in by other means. Include it explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'upstream/xenfs' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen/privcmd: make privcmd visible in domU
xen/privcmd: move remap_domain_mfn_range() to core xen code and export.
privcmd: MMAPBATCH: Fix error handling/reporting
xenbus: export xen_store_interface for xenfs
xen/privcmd: make sure vma is ours before doing anything to it
xen/privcmd: print SIGBUS faults
xen/xenfs: set_page_dirty is supposed to return true if it dirties
xen/privcmd: create address space to allow writable mmaps
xen: add privcmd driver
xen: add variable hypercall caller
xen: add xen_set_domain_pte()
xen: add /proc/xen/xsd_{kva,port} to xenfs
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen: (29 commits)
xen: include xen/xen.h for definition of xen_initial_domain()
xen: use host E820 map for dom0
xen: correctly rebuild mfn list list after migration.
xen: improvements to VIRQ_DEBUG output
xen: set up IRQ before binding virq to evtchn
xen: ensure that all event channels start off bound to VCPU 0
xen/hvc: only notify if we actually sent something
xen: don't add extra_pages for RAM after mem_end
xen: add support for PAT
xen: make sure xen_max_p2m_pfn is up to date
xen: limit extra memory to a certain ratio of base
xen: add extra pages for E820 RAM regions, even if beyond mem_end
xen: make sure xen_extra_mem_start is beyond all non-RAM e820
xen: implement "extra" memory to reserve space for pages not present at boot
xen: Use host-provided E820 map
xen: don't map missing memory
xen: defer building p2m mfn structures until kernel is mapped
xen: add return value to set_phys_to_machine()
xen: convert p2m to a 3 level tree
xen: make install_p2mtop_page() static
...
Fix up trivial conflict in arch/x86/xen/mmu.c, and fix the use of
'reserve_early()' - in the new memblock world order it is now
'memblock_x86_reserve_range()' instead. Pointed out by Jeremy.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (53 commits)
ACPI: install ACPI table handler before any dynamic tables being loaded
ACPI / PM: Blacklist another machine that needs acpi_sleep=nonvs
ACPI: Page based coalescing of I/O remappings optimization
ACPI: Convert simple locking to RCU based locking
ACPI: Pre-map 'system event' related register blocks
ACPI: Add interfaces for ioremapping/iounmapping ACPI registers
ACPI: Maintain a list of ACPI memory mapped I/O remappings
ACPI: Fix ioremap size for MMIO reads and writes
ACPI / Battery: Return -ENODEV for unknown values in get_property()
ACPI / PM: Fix reference counting of power resources
Subject: [PATCH] ACPICA: Fix Scope() op in module level code
ACPI battery: support percentage battery remaining capacity
ACPI: Make Embedded Controller command timeout delay configurable
ACPI dock: move some functions to .init.text
ACPI: thermal: remove unused limit code
ACPI: static sleep_states[] and acpi_gts_bfs_check
ACPI: remove dead code
ACPI: delete dedicated MAINTAINERS entries for ACPI EC and BATTERY drivers
ACPI: Only processor needs CPU_IDLE
ACPICA: Update version to 20101013
...
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile: convert a BUG_ON to BUILD_BUG_ON
arch/tile: make ptrace() work properly for TILE-Gx COMPAT mode
arch/tile: support new info op generated by compiler
arch/tile: minor whitespace/naming changes for string support files
arch/tile: enable single-step support for TILE-Gx
arch/tile: parameterize system PLs to support KVM port
arch/tile: add Tilera's <arch/sim.h> header as an open-source header
arch/tile: Bomb C99 comments to C89 comments in tile's <arch/sim_def.h>
arch/tile: prevent corrupt top frame from causing backtracer runaway
arch/tile: various top-level Makefile cleanups
arch/tile: change lower bound on syscall error return to -4095
arch/tile: properly export __mb_incoherent for modules
arch/tile: provide a definition of MAP_STACK
kmemleak: add TILE to the list of supported architectures.
char: hvc: check for error case
arch/tile: Add a warning if we try to allocate too much vmalloc memory.
arch/tile: update some comments to clarify register usage.
arch/tile: use better "punctuation" for VMSPLIT_3_5G and friends
arch/tile: Use <asm-generic/syscalls.h>
tile: replace some BUG_ON checks with BUILD_BUG_ON checks
Silly though it is, completions and wait_queue_heads use foo_ONSTACK
(COMPLETION_INITIALIZER_ONSTACK, DECLARE_COMPLETION_ONSTACK,
__WAIT_QUEUE_HEAD_INIT_ONSTACK and DECLARE_WAIT_QUEUE_HEAD_ONSTACK) so I
guess workqueues should do the same thing.
s/INIT_WORK_ON_STACK/INIT_WORK_ONSTACK/
s/INIT_DELAYED_WORK_ON_STACK/INIT_DELAYED_WORK_ONSTACK/
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Long ago, PT_TRACESYS_OFF and friends were introduced as hard defines to
avoid straight constants in assembler parts of linux m68k. They are not
used anymore, and were not updated to follow changes in linux kernel.
Remove them. When similar constants are needed, they are now generated
using asm-offsets.c.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new {max,min}3 macros to save some cycles and bytes on the stack.
This patch substitutes trivial nested macros with their counterpart.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Cc: Joe Perches <joe@perches.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes __do_IRQ() from user mode linux. __do_IRQ is deprecated.
Signed-off-by: Richard Weinberger <richard@nod.at>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With glibc 2.11 or later that was built with --enable-multi-arch, the UML
link fails with undefined references to __rel_iplt_start and similar
symbols. In recent binutils, the default linker script defines these
symbols (see ld --verbose). Fix the UML linker scripts to match the new
defaults for these sections.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I think that it's better to detect DMA misuse at build time rather than
calling BUG_ON. Architectures that can't do DMA need to define
CONFIG_NO_DMA.
Thanks to Sam Ravnborg for explaining how CONFIG_NO_DMA and CONFIG_HAS_DMA
work:
http://marc.info/?l=linux-kernel&m=128359913825550&w=2
HAS_DMA is defined like this:
config HAS_DMA
boolean
depends on !NO_DMA
default y
So to set HAS_DMA to true an arch should do:
1) Do not define NO_DMA
2) Define NO_DMA abd set it to 'n'
Must archs - including um - used principle 1).
In the um case we want to say that we do NOT have any DMA.
This can be done in two ways.
a) define NO_DMA and set it to 'y'
b) redefine HAS_DMA and set it to 'n'.
The patch you provided used principle b) where other archs use principle a).
So I suggest you should use principle a) for um too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
T2 are the only alpha SMP systems that do HAE switching at runtime, which
is fundamentally racy on SMP. This patch limits MMIO space on T2 to HAE0
only, like we did on MCPCIA (rawhide) long ago. This leaves us with only
112 Mb of PCI MMIO (128 Mb HAE aperture minus 16 Mb reserved for EISA),
but since linux PCI allocations are reasonably tight, it should be enough
for sane hardware configurations.
Also, fix a typo in MCPCIA_FROB_MMIO macro which shouldn't call set_hae()
if MCPCIA_ONE_HAE_WINDOW is defined. It's more for correctness, as
set_hae() is a no-op anyway in that case.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
access_error() already takes error_code as an argument, so there is
no need for an additional write flag.
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Ying Han <yinghan@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This change reduces mmap_sem hold times that are caused by waiting for
disk transfers when accessing file mapped VMAs.
It introduces the VM_FAULT_ALLOW_RETRY flag, which indicates that the call
site wants mmap_sem to be released if blocking on a pending disk transfer.
In that case, filemap_fault() returns the VM_FAULT_RETRY status bit and
do_page_fault() will then re-acquire mmap_sem and retry the page fault.
It is expected that the retry will hit the same page which will now be
cached, and thus it will complete with a low mmap_sem hold time.
Tests:
- microbenchmark: thread A mmaps a large file and does random read accesses
to the mmaped area - achieves about 55 iterations/s. Thread B does
mmap/munmap in a loop at a separate location - achieves 55 iterations/s
before, 15000 iterations/s after.
- We are seeing related effects in some applications in house, which show
significant performance regressions when running without this change.
[akpm@linux-foundation.org: fix warning & crash]
Signed-off-by: Michel Lespinasse <walken@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Reviewed-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Ying Han <yinghan@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the KM_type stuff is history, clean up the compiler warning.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we no longer need to provide KM_type, the whole pte_*map_nested()
API is now redundant, remove it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Keep the current interface but ignore the KM_type and use a stack based
approach.
The advantage is that we get rid of crappy code like:
#define __KM_PTE \
(in_nmi() ? KM_NMI_PTE : \
in_irq() ? KM_IRQ_PTE : \
KM_PTE0)
and in general can stop worrying about what context we're in and what kmap
slots might be appropriate for that.
The downside is that FRV kmap_atomic() gets more expensive.
For now we use a CPP trick suggested by Andrew:
#define kmap_atomic(page, args...) __kmap_atomic(page)
to avoid having to touch all kmap_atomic() users in a single patch.
[ not compiled on:
- mn10300: the arch doesn't actually build with highmem to begin with ]
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix up drivers/gpu/drm/i915/intel_overlay.c]
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Miller <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit df9ee292 ("Fix IRQ flag handling naming") changed the IRQ flag
handling naming scheme and broke UML:
In file included from arch/um/include/asm/fixmap.h:5,
from arch/um/include/shared/um_uaccess.h:10,
from arch/um/include/asm/uaccess.h:41,
from arch/um/include/asm/thread_info.h:13,
from include/linux/thread_info.h:56,
from include/linux/preempt.h:9,
from include/linux/spinlock.h:50,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/stat.h:60,
from include/linux/module.h:10,
from init/main.c:13:
arch/um/include/asm/system.h:11:1: warning: "local_save_flags" redefined
This patch brings the new scheme to UML and makes it work again.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The linker script cleanup that I did in commit 5d150a97f9 ("um: Clean up
linker script using standard macros.") (2.6.32) accidentally introduced an
ALIGN(PAGE_SIZE) when converting to use INIT_TEXT_SECTION; Richard
Weinberger reported that this causes the kernel to segfault with
CONFIG_STATIC_LINK=y.
I'm not certain why this extra alignment is a problem, but it seems likely
it is because previously
__init_begin = _stext = _text = _sinittext
and with the extra ALIGN(PAGE_SIZE), _sinittext becomes different from the
rest. So there is likely a bug here where something is assuming that
_sinittext is the same as one of those other symbols. But reverting the
accidental change fixes the regression, so it seems worth committing that
now.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Reported-by: Richard Weinberger <richard@nod.at>
Cc: Jeff Dike <jdike@addtoit.com>
Tested by: Antoine Martin <antoine@nagafix.co.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a issue which was introduced by fe2cc53e ("uml: track and make
up lost ticks").
timeval_to_ns() returns long long and not int. Due to that UML's timer
did not work properlt and caused timer freezes.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Request that allocate_resource() use available space from high addresses
first, rather than the default of using low addresses first.
The most common place this makes a difference is when we move or assign
new PCI device resources. Low addresses are generally scarce, so it's
better to use high addresses when possible. This follows Windows practice
for PCI allocation.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228#c42
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The iomem_resource map reflects the available physical address space.
We statically initialize the end to -1, i.e., 0xffffffff_ffffffff, but
of course we can only use as much as the CPU can address.
This patch updates the end based on the CPU capabilities, so we don't
mistakenly allocate space that isn't usable, as we're likely to do when
allocating from the top-down.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allocate from the end of a region, not the beginning.
For example, if we need to allocate 0x800 bytes for a device on bus
0000:00 given these resources:
[mem 0xbff00000-0xdfffffff] PCI Bus 0000:00
[mem 0xc0000000-0xdfffffff] PCI Bus 0000:02
the available space at [mem 0xbff00000-0xbfffffff] is passed to the
alignment callback (pcibios_align_resource()). Prior to this patch, we
would put the new 0x800 byte resource at the beginning of that available
space, i.e., at [mem 0xbff00000-0xbff007ff].
With this patch, we put it at the end, at [mem 0xbffff800-0xbfffffff].
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=16228#c41
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Enable Westmere support on SGI UV. The UV initialization code is dependent on
the APICID bits. Westmere-EX uses different APIC bit mapping than Nehalem-EX.
This code reads the apic shift value from a UV MMR to do the proper bit
decoding to determint the pnode.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20101026212728.GB15071@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pv guests don't have ACPI and need the cpu masks to be set
correctly as early as possible so we call xen_fill_possible_map from
xen_smp_init.
On the other hand the initial domain supports ACPI so in this case we skip
xen_fill_possible_map and rely on it. However Xen might limit the number
of cpus usable by the domain, so we filter those masks during smp
initialization using the VCPUOP_is_up hypercall.
It is important that the filtering is done before
xen_setup_vcpu_info_placement.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
* git://git.infradead.org/battery-2.6:
power_supply: Makefile cleanup
bq27x00_battery: Add missing kfree(di->bus) in bq27x00_battery_remove()
power_supply: Introduce maximum current property
power_supply: Add types for USB chargers
ds2782_battery: Fix units
power_supply: Add driver for TWL4030/TPS65950 BCI charger
bq20z75: Add support for more power supply properties
wm831x_power: Add missing kfree(wm831x_power) in wm831x_power_remove()
jz4740-battery: Add missing kfree(jz_battery) in jz_battery_remove()
ds2760_battery: Add missing kfree(di) in ds2760_battery_remove()
olpc_battery: Fix endian neutral breakage for s16 values
ds2760_battery: Fix W1 and W1_SLAVE_DS2760 dependency
pcf50633-charger: Add missing sysfs_remove_group()
power_supply: Add driver for TI BQ20Z75 gas gauge IC
wm831x_power: Remove duplicate chg mask
omap: rx51: Add support for USB chargers
power_supply: Add isp1704 charger detection driver
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91:
AT91: rtc: enable built-in RTC in Kconfig for at91sam9g45 family
at91/atmel-mci: inclusion of sd/mmc driver in at91sam9g45 chip and board
AT91: pm: make sure that r0 is 0 when dealing with cache operations
AT91: pm: use plain cpu_do_idle() for "wait for interrupt"
AT91: reset: extend alternate reset procedure to several chips
AT91: reset routine cleanup, remove not needed icache flush
AT91: trivial: align comment of at91sam9g20_reset with one more tab
AT91: Fix AT91SAM9G20 reset as per the errata in the data sheet
AT91: add board support for Pcontrol_G20
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
OMAP: DSS2: don't power off a panel twice
OMAP: DSS2: OMAPFB: Allow usage of def_vrfb only for omap2,3
OMAP: DSS2: OMAPFB: make VRFB depends on OMAP2,3
OMAP: DSS2: OMAPFB: Allow FB_OMAP2 to build without VRFB
arm/omap: simplify conditional
OMAP: DSS2: DSI: Remove extra iounmap in error path
OMAP: DSS2: Use dss_features framework on DSS2 code
OMAP: DSS2: Introduce dss_features files
video/omap: remove mux.h include
ARM: omap/fb: move get_fbmem_region() to .init.text
ARM: omap/fb: move omapfb_reserve_sram to .init.text
ARM: omap/fb: move omap_init_fb to .init.text
OMAP: DSS2: OMAPFB: swap front and back porches for both hsync and vsync
OMAP: DSS2: make filter coefficient tables human readable
OMAP: DSS2: Add SPI dependency to Kconfig of ACX565AKM panel
CC arch/sparc/kernel/irq_32.o
arch/sparc/kernel/irq_32.c: In function 'request_fast_irq':
arch/sparc/kernel/irq_32.c:370:25: error: conflicting types for 'trapbase_cpu1'
arch/sparc/include/asm/leon.h:366:22: note: previous declaration of 'trapbase_cpu1' was here
arch/sparc/kernel/irq_32.c:370:40: error: conflicting types for 'trapbase_cpu2'
arch/sparc/include/asm/leon.h:367:22: note: previous declaration of 'trapbase_cpu2' was here
arch/sparc/kernel/irq_32.c:370:55: error: conflicting types for 'trapbase_cpu3'
arch/sparc/include/asm/leon.h:368:22: note: previous declaration of 'trapbase_cpu3' was here
make[3]: *** [arch/sparc/kernel/irq_32.o] Error 1
make[2]: *** [arch/sparc/kernel] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove HAVE_PERF_EVENTS and PERF_USE_VMALLOC under config
SPARC because they're under SPARC64 too. Supporting
perf_event needs atomic64 operations but AFAIK sparc32
doesn't provide them, CMIIW. ;-) Also removes redundant
HAVE_IRQ_WORK line.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that #include <asm/system.h> makes a circular dependency
between kernel.h and bitmap.h which breaks allmodconfig build.
Removing the line makes no change because jump_label.h doesn't
need it actually AFAICS. Compile tested on sparc32 allmodconfig.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rett stack checking code sees the stack is unaligned (in both
the sun4c and srmmu cases) it jumps to the window fault-in path.
But that just tries to page the stack pages in, it doesn't do anything
special if the stack is misaligned.
Therefore we essentially just loop forever in the trap return path.
Fix this by emitting a SIGILL in the stack fault-in code if the stack
is mis-aligned.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analog of what commit 494486a1d2 had done
to alpha (another architecture with similar bug).
One note: in rtrap_32.S part clr %l6 has been a rudiment of left after
commit 28e6103665 (sparc: Fix debugger syscall
restart interactions) has killed %l6 use in there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add function definition for irq_chip.set_wake to enable GPIO to
wake-up the system.
This patch has been tested on a MX51 Babbage system that had suspend
code implemented. The set_wake implementation is necessary for a
GPIO to wake up a system from suspend.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add functionality for the power button on MX51 Babbage board.
Signed-off-by: Dinh Nguyen <Dinh.Nguyen@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The function mxc_expio_init returns 0 on success, so fix the logic for
printing the error case.
Also fixed the wording on the error message.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
When using CP15 cache operations (c7), we make sure that Rd (r0)
is actually 0 as ARM 926 TRM is saying.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For power management at91_pm_enter() routine, use the cpu_do_idle() for a
rock solid "wait for interrupt" implementation.
For AT91SAM9 ARM 926 based chips, we can exceed the cache line length as
we can access RAM even while in self-refresh mode.
We keep plain access to CP15 for at91rm9200 as this feature is not
available: instructions have to be in a single cache line.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Several at91sam9 chips need the alternate reset procedure to be sure to halt
SDRAM smoothly before resetting the chip.
This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips
affected.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Generalize assembler reset routine to allow use on several at91sam9 chips.
This patch replace double definitions of SDRAM controller registers and RSTC
registers with use of classical header files.
For this rework, we remove the not needed icache flush as it is already
done in the calling function: arm_machine_restart().
Rename at91sam9g20_reset.S to generalize to several chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
If the SDRAM is not cleanly shutdown before reset it can be left driving
the bus, which then stops the bootloader booting from NAND.
Signed-off-by: Peter Horton <phorton@bitbox.co.uk>
[nicolas.ferre@atmel.com: change file header line order]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Board is a carrier board for Stamp9G20, with additional peripherals
for a building automation system
Signed-off-by: Peter Gsellmann <pgsellmann@portner-elektronik.at>
[nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Now that the genirq code provides an IRQ bitmap of its own and the
necessary API to manipulate it, there's no need to keep our own version
around anymore.
In the process we kill off some unused IRQ reservation code, with future
users now having to tie in to the genirq API as normal.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The generic version of l2x0_inv_all is only called just after disabling
the L2 cache and is surrounded by a spinlock. However, we're not really
turning off the L2 cache right now, and the PL310 does not support
exclusive accesses (used to implement the spinlock). So, the
invalidation needs to be done without the spinlock.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Hans-Juergen Koch <hjk@linutronix.de>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
For the big buffers which are in excess of cache size, the maintaince
operations by PA are very slow. For such buffers the maintainace
operations can be speeded up by using the WAY based method.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
The cache size is needed for to optimise range based
maintainance operations
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Replace tab with space after #define to be consisten with other
define in the file. Also move the bit mask below the register offsets.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
The machine_kexec() calls outer_disable which can crash on OMAP4
becasue of trustzone restrictions.
This patch overrides the default l2x0_disable with a OMAP4
specific implementation taking care of trustzone
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Add flush_all, inv_all and disable functions to the l2x0 code. These
functions are called from kexec code to prevent random crashes in the
new kernel.
Platforms like OMAP which control L2 enable/disable via SMI mode can
override the outer_cache.disable() function to implement their own.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
kexec does not disable the outer cache before disabling the inner
caches in cpu_proc_fin(). So L2 is enabled across the kexec jump. When
the new kernel enables chaches again, it randomly crashes.
Disabling L2 before calling cpu_proc_fin() cures the problem.
Disabling L2 requires the following new functions: flush_all(),
inv_all() and disable(). Add them to outer_cache_fns and call them
from the kexec code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
With this L2 cache controller, the cache maintenance by PA and sync
operations are atomic and do not require a "wait" loop. This patch
conditionally defines the cache_wait() function.
Since L2x0 cache controllers do not work with ARMv7 CPUs, the patch
automatically enables CACHE_PL310 when only CPU_V7 is defined.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
CPUs can be in either the legacy 29-bit or 32-bit physical addressing
modes. This follows the x86 approach of tracking the phys bits in cpuinfo
and exposing it to userspace through procfs.
This change was requested to permit kexec-tools to detect the physical
addressing mode in order to determine the appropriate address mangling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds to support ethernet for SMDKV310 and SMDKC210 board.
- define smc911x resources
- define configurations of smc911x platform data
- define platform device "smsc911x"
- initialize srom controller for lan9215 chip
Signed-off-by: Daein Moon <moon9124@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
In commit (c5d38f08): "mx31_3ds: revert 3ds debug board relate code"
the debug board definitions are placed in a separate file.
Remove the remaining debug board related define from mach-mx31_3ds.c.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits)
microblaze: Fix build with make 3.82
fbdev/xilinxfb: Microblaze driver support
microblaze: Support C optimized lib functions for little-endian
microblaze: Separate library optimized functions
microblaze: Support timer on AXI lite
microblaze: Add support for little-endian Microblaze
microblaze: KGDB little endian support
microblaze: Add PVR for endians plus detection
net: emaclite: Add support for little-endian platforms
microblaze: trivial: Add comment for AXI pvr
microblaze: pci-common cleanup
microblaze: Support early console on uart16550
microblaze: Do not compile early console support for uartlite if is disabled
microblaze: Setup early console dynamically
microblaze: Rename all uartlite early printk functions
microblaze: remove early printk uarlite console dependency from header
microblaze: Remove additional compatible properties
microblaze: Remove hardcoded asm instraction for PVR loading
microblaze: Use static const char * const where possible
microblaze: Define VMALLOC_START/END
...
This patch adds support SROMC for S5PV310 and S5PC210.
Signed-off-by: Daein Moon <moon9124@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the s3c_gpio_getpull() API that has been missed in the
plat-samsung/gpio-config.c and actullay there is its extern declaration
in plat/gpio-cfg.h.
Signed-off-by: Daein Moon <moon9124@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
CC arch/x86/xen/setup.o
arch/x86/xen/setup.c: In function 'xen_memory_setup':
arch/x86/xen/setup.c:161: error: implicit declaration of function 'xen_initial_domain'
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: lis3: Release resources in case of failure
hwmon: lis3: Short explanations of platform data fields
hwmon: lis3: Enhance lis3 selftest with IRQ line test
hwmon: lis3: use block read to access data registers
hwmon: lis3: Adjust fuzziness for 8 bit device
hwmon: lis3: New parameters to platform data
hwmon: lis3: restore axis enabled bits
hwmon: lis3: Power on corrections
hwmon: lis3: Update coordinates at polled device open
hwmon: lis3: Cleanup interrupt handling
hwmon: lis3: regulator control
hwmon: lis3: pm_runtime support
Kirkwood: add fan support for Network Space Max v2
hwmon: add generic GPIO fan driver
hwmon: (coretemp) fix reading of microcode revision (v2)
hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
hwmon: (pkgtemp) align driver initialization style with coretemp
hwmon: LTC4261 Hardware monitoring driver
hwmon: (lis3) add axes module parameter for custom axis-mapping
hwmon: (hp_accel) Add HP Mini 510x family support
...
In the MN10300 arch, we occasionally see an assertion being tripped in
alloc_cwqs() at the following line:
/* just in case, make sure it's actually aligned */
---> BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align));
return wq->cpu_wq.v ? 0 : -ENOMEM;
The values are:
wa->cpu_wq.v => 0x902776e0
align => 0x100
and align is calculated by the following:
const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS,
__alignof__(unsigned long long));
This is because the pointer in question (wq->cpu_wq.v) loses some of its
lower bits to control flags, and so the object it points to must be
sufficiently aligned to avoid the need to use those bits for pointing to
things.
Currently, 4 control bits and 4 colour bits are used in normal
circumstances, plus a debugging bit if debugging is set. This requires
the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512
bytes aligned with debugging).
PERCPU() alignment on MN13000, however, is only 32 bytes as set in
vmlinux.lds.S. So we set this to PAGE_SIZE (4096) to match most other
arches and stick a comment in alloc_cwqs() for anyone else who triggers
the assertion.
Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No one uses these MMRs so we didn't notice when the anomaly handling
logic was inverted.
Reported-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic). So punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
b40827fa72 added an include
directive which is needless and is taken care of by a previous
one. Remove it.
Caught-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Cc: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <20101025162523.GA4712@a1.tnic>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit b40827fa72 ("x86-32, mm: Add an initial page table for core
bootstrapping") added an include directive which is needless and is
taken care of by a previous one. Remove it.
Caught-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (44 commits)
eeepc-wmi: Add cpufv sysfs interface
eeepc-wmi: add additional hotkeys
panasonic-laptop: Simplify calls to acpi_pcc_retrieve_biosdata
panasonic-laptop: Handle errors properly if they happen
intel_pmic_gpio: fix off-by-one value range checking
IBM Real-Time "SMI Free" mode driver -v7
Add OLPC XO-1 rfkill driver
Move hdaps driver to platform/x86
ideapad-laptop: Fix Makefile
intel_pmic_gpio: swap the bits and mask args for intel_scu_ipc_update_register
ideapad: Add param: no_bt_rfkill
ideapad: Change the driver name to ideapad-laptop
ideapad: rewrite the sw rfkill set
ideapad: rewrite the hw rfkill notify
ideapad: use EC command to control camera
ideapad: use return value of _CFG to tell if device exist or not
ideapad: make sure we bind on the correct device
ideapad: check VPC bit before sync rfkill hw status
ideapad: add ACPI helpers
dell-laptop: Add debugfs support
...
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
Commit b0ae198113 ("security: remove unused parameter from
security_task_setscheduler()") broke the build of
arch/mips/kernel/mips-mt-fpaff.c. The function arguments were
unnecessary, not the semicolon ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
sh: i2c-sh7760: Replase from ctrl_* to __raw_*
sh: clkfwk: Shuffle around to match the intc split up.
sh: clkfwk: modify for_each_frequency end condition
sh: fix clk_get() error handling
sh: clkfwk: Fix fault in frequency iterator.
sh: clkfwk: Add a helper for rate rounding by divisor ranges.
sh: clkfwk: Abstract rate rounding helper.
sh: clkfwk: support clock remapping.
sh: pci: Convert to upper/lower_32_bits() helpers.
sh: mach-sdk7786: Add support for the FPGA SRAM.
sh: Provide a generic SRAM pool for tiny memories.
sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
sh: pci: Support slot 4 routing on SDK7786.
sh: Fix up PMB locking.
sh: mach-sdk7786: Add support for fpga gpios.
sh: use pr_fmt for clock framework, too.
sh: remove name and id from struct clk
sh: free-without-alloc fix for sh_mobile_lcdcfb
sh: perf: Set up perf_max_events.
sh: perf: Support SH-X3 hardware counters.
...
Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu: (21 commits)
m68knommu: convert to using tracehook_report_syscall_*
m68knommu: some boards use fixed phy for FEC ethernet
m68knommu: support the external GPIO based interrupts of the 5272
m68knommu: mask of vector bits in exception word properly
m68knommu: change to new flag variables
m68knommu: Fix MCFUART_TXFIFOSIZE for m548x.
m68knommu: add basic mmu-less m548x support
m68knommu: .gitignore vmlinux.lds
m68knommu: stop using __do_IRQ
m68knommu: rename PT_OFF_VECTOR to PT_OFF_FORMATVEC.
m68knommu: add support for Coldfire 547x/548x interrupt controller
m68k{nommu}: Remove unused DEFINE's from asm-offsets.c
m68knommu: whitespace cleanup in 68328/entry.S
m68knommu: Document supported chips in intc-2.c and intc-simr.c.
m68knommu: fix strace support for 68328/68360
m68knommu: fix default starting date
arch/m68knommu: Removing dead 68328_SERIAL_UART2 config option
arch/m68knommu: Removing dead RAM_{16,32}_MB config option
arch/m68knommu: Removing dead M68KFPU_EMU config option
arch/m68knommu: Removing dead RELOCATE config option
...
When system uses 36bit physical address, res.start is 36bit
physical address. But the function of in_be32 returns 32bit
physical address. Then both of them compared each other is
wrong. So by converting the address of res.start into
the right format fixes this issue.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move Freescale elbc interrupt from nand driver to elbc driver.
Then all elbc devices can use the interrupt instead of ONLY nand.
For former nand driver, it had the two functions:
1. detecting nand flash partitions;
2. registering elbc interrupt.
Now, second function is removed to fsl_lbc.c.
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Export the cpu configuration topology via sysinfo. Two new lines are
introduced:
CPU Topology HW: 0 0 0 4 6 4
CPU Topology SW: 0 0 0 0 4 24
The HW line describes the cpu topology nesting levels when the maximum
nesting level is used to get the corresponding SYSIB.
The SW line describes what Linux is actually using. In this case it
supports only two levels (CONFIG_SCHED_BOOK off) and therefore the
hardware folded the two lower levels in the SYSIB response block.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the topology sysinfo SYSIB definitions to the proper place in
asm/sysinfo.h where they should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cpu topology facility detection to early setup code where it
should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Store the facility list once at system startup with stfl/stfle and
reuse the result for all facility tests.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Enable PFPO, floating point extension, distinct-operands,
fast-BCR-serialization, high-word, interlocked-access, load/store-
on-condition, and population-count facilities for guests.
(bits 37, 44 and 45).
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 050eef364a
[S390] fix tlb flushing vs. concurrent /proc accesses
broke KVM on s390x. On every schedule a
Badness at include/asm/mmu_context.h:83 appears. s390_enable_sie
replaces the mm on the __running__ task, therefore, we have to
increase the attach count of the new mm.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Switch default value of the kernel parameter 'topology' from off to on.
Various performance measurements have finally shown that there are no
(known) regressions anywhere.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Up to now print_cpu_info() uses the cpu address stored in it's local
lowcore to print a message to the console. The cpu address in the
lowcore is (in this case) however not the physical cpu address of the
local cpu. It's the address of the cpu that issued the sigp restart
which started the local cpu.
Fix this by using the store cpu address instruction instead.
It's not that anybody really cares since this is broken since more than
ten years...
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ieee_instruction_pointer can not be read from user space anymore
since git commit 613e1def6b, the ptrace
interface always returns zero. Remove it from the thread_struct. It
is still present in the user_regs_struct for compatability reasons.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do the setup of the stack overflow argument for the sixth system
call parameter right before the branch to the system call function.
That simplifies the system call parameter access code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The store-cpu-id instruction has a minimum alignment of 8. Reflect
that in the definition of struct cpuid.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read external interrupts parameters from the lowcore in the first
level interrupt handler in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Read all required fields for program checks from the lowcore in the
first level interrupt handler in entry[64].S. If the context that
caused the fault was enabled for interrupts we can now re-enable the
irqs in entry[64].S.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All architectures besides s390 have pte_mkhuge() defined in pgtable.h.
So move the function to pgtable.h on s390 as well.
Fixes a compile error introduced with "hugetlb: hugepage migration core"
in linux-next which only happens on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Raise SIGBUS with a siginfo structure. Deliver BUS_ADRERR as si_code and
the address of the fault in the si_addr field.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch adds a notification mechanism to inform ccw drivers
about changes to channel paths, which occured while the device
is online.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the cmm module is compiled into the kernel it will crash when
writing to the R/O data section.
Reason is the lower to upper case conversion of the "sender" module
parameter which ignored the fact that the pointer is preinitialized.
Introduced with 41b42876 "cmm, smsgiucv_app: convert sender to
uppercase"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
schedule() makes sure that prev != next before calling switch_to().
Therefore remove the redundant check.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the previous task was a kernel thread there is no need to save the
contents of the fpu and access registers since they aren't used in
kernel mode.
For the same reason it is not necessary to restore these registers if
the next task is a kernel thread.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a kernel config option for the IBM zEnterprise 196. This will
produce faster code on newer compilers using the -march=z196 option.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Display machine capacity adjustment indicator and capacity
change reason if available in /proc/sysinfo.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve performance of the sske operation by using the nonquiescing
variant if the affected page has no mappings established. On machines
with no support for the new sske variant the mask bit will be ignored.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the store indication bit in the translation exception code on
page faults to avoid the protection faults that immediatly follow
the page fault if the access has been a write.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no difference if cpu_die is called from enabled or disabled
context. Except that the fast_gup code might be called via
cpu_die -> idle_task_exit -> __mm_drop -> crst_table_free. Which in
turn grabs and releases a spinlock using the _bh ops, which is not
allowed in irq disabled context, since spin_unlock_bh will
unconditionally enable interrupts again.
To get rid of the warning emitted by the softirq code just move the
code to enabled context.
In this case this doesn't fix a bug, we just get rid of a warning.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set ARCH_HAS_SG_CHAIN for scatter lists on s390. Without this flag the
SCSI code limits the maximum number of segments, so set it to make
proper use of the FCP channel hardware.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introducing this Kbuild file allow us to:
make arch/s390/
And thus building all the core part of s390.
Same as on other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the zero page is mapped to virtual user space addresses that differ
only in bit 2^12 or 2^13 we get L1 cache synonyms which can affect
performance. Follow the mips model and use multiple zero pages to avoid
the synonyms.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
- enable pm for ADI boards
- drop security option as no one uses it
- enable uninitialized mmap for everyone
- disable wireless by default as no one uses it
- disable cfq io sched as noop is fine
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Move all the pin settings out of the Kconfig and into the platform
resources (MII vs RMII). This clean up also lets us push out the
phy settings so that board porters may control the layout.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch changes VMALLOC_END from 0xE0000000 to 0xF6000000, because
some systems want to use more vmalloc()/ioremap() area and now don't use
from at 0xE0000000 to 0xF6000000 (the start of Samsung SoCs' VA space)
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes VMALLOC_END from 0xE0000000 to 0xF6000000, because
some systems want to use more vmalloc()/ioremap() area and now don't use
from at 0xE0000000 to 0xF6000000 (the start of Samsung SoCs' VA space)
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves the start address of Samsung SoCs' VA space so that
can use more vmalloc()/ioremap() space. Of course need to change the
VMALLOC_END for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds EINT(External Interrupt) support on S5PV310 and S5PC210.
All EINTs are transferred to GIC through interrupt combiner.
Signed-off-by: Jongsun Han <jongsun.han@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the definition for both IRQs and GPIO registers for
external interrupts.
Signed-off-by: Jongsun Han <jongsun.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds L2 cache initialization code in cpu.c of ARCH_S5PV310.
It includes TAG and Data latency, Prefetch, and Power configurations.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Basically, need L2 cache initialize function in ARCH_S5PV310. So it would
be better to move it into ARCH_S5PV310 common part. This patch removes L2
cache initialization code at the each board file.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds L2X0 Prefetch and Power control register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch moves DMA clock enable functionality into pl330_probe() of
plat-samsung/s3c_pl330.c (PL330 DMAC driver) and disable functionality
into pl330_remove().
For now according to clock policy of Samsung SoCs' mainline, clocks which
are used in the driver should be controlled by each own.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
[kgene.kim@samsung.com: minor title and comment edit]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is matched-up DMA platform device id to its clock id.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modify to DMA operation clock into disable list for default
clock setting.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMA operation clock which is disabled as default.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds DMA operation clock which is disabled as default.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Audio, Keypad and ADC inherit PCLKD1 clock source.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add cose related to regulator. To control powre consumeption
have registered the voltage consumer of WM8994 to the regulator framework.
Additionally, I explain the constraints of the regulator of WM8994 codec.
All these consumer supply of WM8994 codec connected the regulator(VCC_1.8V)
on a circuit diagram. "VCC_1.8V" regulator is always enabled, because it is
used to many devices on Goni/Aquila board. This is required especially
when there are many devices physically attached to "VCC_1.8V" and some of
they did not "register" as consumers to "VCC_1.8V". "VCC_1.8V" might be
turned off by those who are registered while "unregistered" are still active
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add initialization code of audio and I2S platform drivers
to Goni and Aquila board.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch the I2C board information for the WM8994 used in the Goni/Aquila
as audio codec and adds the I2C platform drivers.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds GPIOlib support for S5PV310 and S5PC210.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
[kgene.kim@samsung.com: Fix NR_IRQS]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds initial map for GPIO2 and GPIO3.
S5PV310/S5PC210 has separated GPIO1, GPIO2 and GPIO3.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch updates MAX_COMBINER_NR from 39 to 40 because
S5PV310 need 39th combiner for including EINT16_31.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds warning about changing EPLL rate to notice that other
driver that controls H/W, which is using EPLL, will has unknown effects
by this EPLL rate change.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5P Samsung SoCs has a EPLL to support various PLL clock sources for other
H/W blocks. Until now, to control EPLL, each of SoCs make their own functions
in 'mach-s5pxxx/clock.c'. But some of functions, 'xxx_epll_get_rate()' and
'xxx_epll_enable()', are exactly same in all S5P SoCs, so this patch move
these duplicated codes to common EPLL functions that use platform wide.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds audio clocks(SCLK_AUDIO{0,1,2} and SCLK_AUDIO) to be
initial as a sysclk on boot-time.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add SCLK_SPDIF clock to support source clock of S/PDIF
on S5PV210.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add S/PDIF platform device to support S/PDIF PCM audio
on S5PV210.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add SCLK_SPDIF clock to support source clock of S/PDIF
on S5PC100.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch modify SCLK_AUDIO{0,1,2} to be initial as sysclks
on boot-time.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch add S/PDIF platform device to support S/PDIF PCM audio
on S5PC100.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since it's exported we should make sure we're using the prototype
others see.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since it's exported we should make sure we're using the prototype
others see.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds ARCH_HAS_CPUFREQ in arch/arm/Kconfig for S5PV210,
and updates mach-s5pv210/Makefile for supporting build CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds CPUFREQ driver for supporting DFS(Dynamic Frequency Scaling).
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds some CMU(Clock Management Unit) registers for
supporting CPUFREQ and some drivers.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds MOUT_DMC0 and SCLK_DMC0 for checking the dmc0 clock
in CPUFREQ driver.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Current fout_apll has fixed rate value. So CPUFREQ driver gets
incorrect value when finding current CPU frequency. Because some
operation level need to change APLL.
Added get_rate function for fout_apll can give correct frequency
value when calling get_rate function.
Signed-off-by: Jaecheol Lee <jc.lee@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV310 and S5PC210 support more I2C devices than previous SoCs.
Add the device support code for them.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S5PV310 and S5PC210 support total 8 (+ 1 dedicated for HDMI) I2C devices.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The name of the I2C2 and I2C3 interrupt should be IIC2 and IIC3
instead of CAN0 and CAN1.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes I2C2 and I2C3 interrupt name from IRQ_CANX to IRQ_IICX
according other SoCs' I2C interrupt naming rule.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Basically S5P SoCs use the Samsung common VA address mapping where
plat-samsung and use plat-s5p's mapping also. The later is a little
mess. So this patch cleans it up.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Camera devices use the I2C0 and Gyro uese the I2C1 on universal board.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
OneNAND device support for Universal board.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clock types into platform data to support
external clock divider instead of internal clock divider.
It is defined that what kinds of clock type is used in machine.
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds to change bus width and host capability of HSMMC,
when HSMMC is only configured with another value of bus width
and host capability from default one.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC for S5PV310(SMDKV310) and
S5PC210(SMDKC210).
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds initialization HSMMC device information.
And HSMMC platform data like card detect, data bus width
and capability is configured.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC for S5PV310 and S5PC210 and
setup for HSMMC host controller and also related GPIO.
At most 4 channel can be used at the same time.
A user can configure SDHCI data bus as 8bit or 4bit.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch clean up the GPIO code and removes useless GPIO addresses.
It can be calculated with offset, the 'base' member of s3c_gpio_chip
is also initialized in the init function.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
When merged patches, missed IRQ_EINT_BIT() definition from commit ea31fd43
(ARM: S5PV210: Add Power Management Support). The IRQ_EINT_BIT() is used
in the Power Management operation (plat-samsung/pm.c).
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Stephen Rothwell reported this build warning:
arch/x86/oprofile/op_model_amd.c: In function 'ibs_eilvt_valid':
arch/x86/oprofile/op_model_amd.c:289: warning: 'offset' may be used uninitialized in this function
And correctly observed that indeed the variable is used uninitialized in
this function. The result of this bug can be a debug printk with a bogus
value.
Also fix a few more small details that made this function hard to read
and which probably contributed to the bug being introduced to begin with:
- Use more symmetric error conditions
- Remove the !0 obfuscation
- Add newlines to the printk output
- Remove bogus linebreaks in printk strings and elsewhere
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20101025115736.41d51abe.sfr@canb.auug.org.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add platform data, necessary to use Sony IMX074 camera sensor with AP4EVB.
Note: this does not work reliably without an API to reserve contiguous and
coherent memory for V4L DMA buffers. Such memory reservation has to be added as
soon as a suitable API becomes available.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just as it says, if this is merged along with the other patch, the
driver supports the U300 NAND flash interface.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
