This is a leftover from back when a recovery action didn't go through
dev_close(), and was meant to shoot down all remaining af_iucv sockets
on the interface.
Now that the offline path always calls dev_close(), the
NETDEV_GOING_DOWN event from __dev_close_many() is sufficient and this
hack can be removed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inet_make_mask() to replace some complicated bit-fiddling.
Also use the right data types to replace some raw memcpy calls with
proper assignments.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate some duplicated code for adding RXIP/VIPA addresses, and
move the locking to where it's actually needed.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code that dumps the RXIP/VIPA/IPATO addresses via sysfs
first checks whether the buffer still provides sufficient space to hold
another formatted address.
But the maximum length of an formatted IPv4 address is 15 characters,
not 12. So we underestimate the max required length and if the buffer
was previously filled to _just_ the right level, a formatted address can
end up being truncated.
Revamp these code paths to use the _actually_ required length of the
formatted IP address, and while at it suppress a gratuitous newline.
Also use scnprintf() to format the output. In case of a truncation, this
would allow us to return the number of characters that were actually
written.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
card->wait_q is shared by different users, for different wake-up
conditions. qeth_irq() can potentially trigger multiple of these
conditions:
1) A change to channel->irq_pending, which qeth_send_control_data() is
waiting for.
2) A change to card->state, which qeth_clear_channel() and
qeth_halt_channel() are waiting for.
As qeth_irq() does only a single wake_up(), we might miss to wake up
a second eligible waiter. Luckily all waiters are guarded with a
timeout, so this situation should recover on its own eventually.
To make things work robustly, add an additional wake_up() for changes
to channel->state. And extract a helper that updates
channel->irq_pending along with the needed wake_up().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A qeth device that's offline should not be receiving any IRQs - all
pending IOs have been terminated, and we avoid starting any new ones.
So rather than immediately registering the IRQ handler when the device
is probed, only register it while the device is online.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: TSN support using TAPRIO API
This series adds TSN support (EST and Frame Preemption) for stmmac driver.
1) Adds the HW specific support for EST in GMAC5+ cores.
2) Adds the HW specific support for EST in XGMAC3+ cores.
3) Integrates EST HW specific support with TAPRIO scheduler API.
4) Adds the Frame Preemption suppor on stmmac TAPRIO implementation.
5) Adds the HW specific support for Frame Preemption in GMAC5+ cores.
6) Adds the HW specific support for Frame Preemption in XGMAC3+ cores.
7) Adds support for HW debug counters for Frame Preemption available in
GMAC5+ cores.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be useful for debug. Add these counters on GMAC5+ cores just
like we did for XGMAC.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the HW specific support for Frame Preemption on XGMAC3+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the HW specific support for Frame Preemption on GMAC5+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for Frame Preemption using TAPRIO API. This works along
with EST feature and allows to select if preemptable traffic shall be
sent during specific queues opening time.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the EST code for XGMAC and QoS we can use it with the
TAPRIO scheduler. Integrate it into the main driver and use the API to
configure the EST feature.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for EST in XGMAC cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for EST in GMAC5+ cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Improvements for -next
Misc improvements for stmmac.
1) Adds more information regarding HW Caps in the DebugFS file.
2) Allows interrupts to be independently enabled or disabled so that we don't
have to schedule both TX and RX NAPIs.
3) Stops using a magic number in coalesce timer re-arm.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have pending packets we re-arm the TX timer with a magic value.
This changes the re-arm of the timer from 10us to the user-defined
coalesce value. As we support different speeds, having a magic value of
10us can be either too short or to large depending on the speed so we
let user configure it. The default value of the timer is 1ms but it can
be reconfigured by ethtool.
Changes from v1:
- Reword commit message (Jakub)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By using this mechanism we can get rid of the not so nice method of
scheduling TX NAPI when the RX was scheduled. No bandwidth reduction was
seen with this change.
Changes from v1:
- Remove useless comment (Jakub)
- Do not bind the TX clean to NAPI budget (Jakub)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA Capabilites have grown but the DebugFS that shows this info has not
been updated. Lets add the missing information.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Fixes for -net
Fixes for stmmac.
1) Fixes the filtering selftests (again) for cases when the number of multicast
filters are not enough.
2) Fixes SPH feature for MTU > default.
3) Fixes the behavior of accepting invalid MTU values.
4) Fixes FCS stripping for multi-descriptor packets.
5) Fixes the change of RX buffer size in XGMAC.
6) Fixes RX buffer size alignment.
7) Fixes the 16KB buffer alignment.
8) Fixes the enabling of 16KB buffer size feature.
9) Always arm the TX coalesce timer so that missed interrupts do not cause
a TX queue timeout.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If TX Coalesce timer is enabled we should always arm it, otherwise we
may hit the case where an interrupt is missed and the TX Queue will
timeout.
Arming the timer does not necessarly mean it will run the tx_clean()
because this function is wrapped around NAPI launcher.
Fixes: 9125cdd1be ("stmmac: add the initial tx coalesce schema")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to align the RX buffer size to at least 16 byte so that IP
doesn't mis-behave. This is required by HW.
Changes from v2:
- Align UP and not DOWN (David)
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching between buffer sizes we need to clear the previous value.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the last received buffer contains the FCS field. Check for end of
packet before trying to strip the FCS field.
Fixes: 88ebe2cf7f ("net: stmmac: Rework stmmac_rx()")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU value is determined by the maximum size of TX FIFO so
that a full packet can fit in the FIFO. Add a check for this in the MTU
change callback.
Also check if provided and rounded MTU does not passes the maximum limit
of 16K.
Changes from v2:
- Align MTU before checking if its valid
Fixes: 7ac6653a08 ("stmmac: Move the STMicroelectronics driver")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split Header feature needs to know the size of RX buffer but current
code is determining it too late. Fix this by moving the RX buffer
computation to earlier stage.
Changes from v2:
- Do not try to align already aligned buffer size
Fixes: 67afd6d1cf ("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running the MC and UC filter tests we setup a multicast address
that its expected to be blocked. If the number of available multicast
registers is zero, driver will always pass the multicast packets which
will fail the test.
Check if available multicast addresses is enough before running the
tests.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
net/nfc/nci/uart.c, 349:
nci_skb_alloc in nci_uart_default_recv_buf
net/nfc/nci/uart.c, 255:
(FUNC_PTR)nci_uart_default_recv_buf in nci_uart_tty_receive
net/nfc/nci/uart.c, 254:
spin_lock in nci_uart_tty_receive
nci_skb_alloc(GFP_KERNEL) can sleep at runtime.
(FUNC_PTR) means a function pointer is called.
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC for
nci_skb_alloc().
This bug is found by a static analysis tool STCheck written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've been chasing a weird and obscure crash that was userspace stack
corruption, and finally narrowed it down to a bit flip that made a
stack address invalid. io_wq_submit_work() unconditionally flips
the req->rw.ki_flags IOCB_NOWAIT bit, but since it's a generic work
handler, this isn't valid. Normal read/write operations own that
part of the request, on other types it could be something else.
Move the IOCB_NOWAIT clear to the read/write handlers where it belongs.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In ezusb_init, if upriv is NULL, the code crashes. However, the caller
in ezusb_probe can handle the error and print the failure message.
The patch replaces the BUG_ON call to error return.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
NVIDIA Tegra SoCs do not like when OOB wake is enabled and WiFi interface
is in DOWN state during suspend. This results in a CPU hang on programming
OOB wake-up state of the GPIO controller during of system's suspend.
The solution is trivial: don't enable wake for the OOB interrupt when it
should be disabled.
This fixes hang on Tegra20 (Acer A500) and Tegra30 (Nexus 7) devices which
are using BCM4329 and BCM4330 WiFi chips respectively.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_usbdev_qinit() the allocated memory for
reqs is leaking if usb_alloc_urb() fails. Release reqs in the error
handling path.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With RSDB mode, FMAC and firmware are able to create 2 or more AP,
so we should not set mbss in vif structure if firmware does not
support MBSS feature.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With firmware RSDB feature
1. The maximum support interface is four.
2. The maximum difference channel is two.
3. The maximum interfaces of {station/p2p client/AP} are two.
4. The maximum interface of p2p device is one.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM4359 is a 2x2 802.11 abgn+ac Dual-Band HT80 combo chip and it
supports Real Simultaneous Dual Band feature.
Based on a similar patch by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4359 dongles do not support setting roaming parameters (error -52).
Do not fail the 80211 configuration in this case.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer 4359 chip revisions need a different rambase address.
This fixes firmware download on such devices which fails otherwise.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4359. Also
enable and configure F1 MesBusyCtrl. It fixes DMA error while having
UDP bi-directional traffic.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
[slightly adapted for rebase on mainline linux]
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two D11 cores in RSDB chips like 4359. We have to reset two
D11 cores simutaneously before firmware download, or the firmware may
not be initialized correctly and cause "fw initialized failed" error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92de_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92de_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92c_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92ce_signal_scale_mapping is identical to the generic
version rtl_signal_scale_mapping. Remove _rtl92ce_signal_scale_mapping
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92d_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92c_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_query_rxpwrpercentage is identical to the generic
version rtl_query_rxpwrpercentage. Remove _rtl92c_query_rxpwrpercentage
and use the generic function.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
storage interface descriptors to avoid submitting an URB to an invalid
endpoint.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: a1030e92c1 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device")
Cc: stable <stable@vger.kernel.org> # 2.6.19
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: dad0d04fa7 ("rsi: Add RS9113 wireless driver")
Cc: stable <stable@vger.kernel.org> # 3.15
Cc: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Cc: stable <stable@vger.kernel.org> # 4.4
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 9afac70a73 ("orinoco: add orinoco_usb driver")
Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
