[Why]
link_stream is never NULL here as we've dereferenced it a couple lines before
and have done so for a couple months now.
[How]
- Drop the NULL check.
- Initialize where we know link_stream is non-NULL
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Do not fill Null packet in the blank period for new packet gen
This is based on HW IP team recommended default setting change.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When the system is going into suspend, set_backlight gets called
after the eDP got blanked. Since smooth brightness is enabled,
the driver will make a call into the DMCU to ramp the brightness.
The DMCU would try to enable ABM to do so. But since the display is
blanked, this ends up causing ABM1_ACE_DBUF_REG_UPDATE_PENDING to
get stuck at 1, which results in a dead lock in the DMCU firmware.
[how]
Disable brightness ramping when the eDP display is blanked.
Signed-off-by: Zi Yu Liao <ziyu.liao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When we recover from hang, we do not want to skip the audio enable call.
[How]
Disable audio in dc_reinitialize_hardware
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DSC should be powered-on only on as-needed basis, i.e. if the mode
requires it
[how]
Loop over all the DSCs at driver init time and power-gate each
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current default is sufficient for a flag that does not change.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When launch D10.2, driver will write DPCD 0x107 with 0x00
[How]
Read MAX_DOWNSPREAD (0x0003h) then keep in current
link settings
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A hubp pointer was being passed to DCN1 functions, which
expect the enclosing structure (for the purpose of container_of macros)
to be dcn10_hubp, but the actual type was dcn20_hubp.
[How]
Copy existing DCN1 functions and alter them slightly for use with
dcn20_hubp.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before accessing it's vtable, check that stream_encoder is non-null.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to implement register programming for HDR dynamic
metadata transmission and tests.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to check the pipe crc source through debugfs for bypass mode test.
[How]
add implementation of amdgpu_dm_crtc_get_crc_sources and hook into drm_crtc
callback get_crc_sources.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to compare DPRX CRCs with framebuffer CRCs for digital bypass mode.
[How]
Hook into DRM to grab DP receiver CRCs through drm_dp_start_crc.
Signed-off-by: Dingchen Zhang <dingchen.zhang@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware docs state that we must wait until the GPUVM context is ready
after programming it.
[How]
Poll until the valid bit of PAGE_TABLE_BASE_ADDR_LO32 is set to 1 after
programming it.
v2: fix include for udelay (Alex)
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Specifically to one panel,
TCON is able to accept active video signal quickly, but
the Source Driver requires 2-3 frames of extra time.
It is a Panel issue since TCON needs to take care of
all Sink requirements including Source Driver. But in
this case it does not.
Customer is asking to add fixed T7 delay as panel
workaround.
[How]
Add monitor specific patch to add T7 delay
Signed-off-by: Anthony Koo <anthony.koo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This change adds EMP packet programming for enabling dsc with
hdmi. The packets are structured according to VESA HDMI 2.1x
r2 spec, section 10.10.2.2.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for 2 purposes:
1. get raw register value dumped on the log, which will make it easier
to talk to other team who only knows about the register
2. enable other HW to be able to use the same interface as raven to log
clock register data
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The current code will not wait for the entire frame
after global unlock.
This causes dsc dynamic target bpp update corruption when
there is a surface update immediately happens after this.
[how]
Wait for the entire whole frame after unlock before continuing
the rest of stream and surface update.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Pass and use pixel clock in 100 Hz to Audio for HDMI
audio DTO for Audio wall clock programming so audio DTO gets
increased precision for timings with /1001 factor.
-For HDMI TMDS for N and CTS ACR tables are based on 10 KHz
units, these does not need to be modified as N and CTS values
are still valid using current tables.
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DCE110, DCE112 and DCE120 the max_clks_by_state for the clk_mgr are
copied from their respective table before the call to
dce_clk_mgr_construct, but then dce_clk_mgr_construct overwrites
these with the dce80_max_clks_by_state.
[How]
Copy these after we call dce_clk_mgr_construct so we're using the
right tables.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We reset the optimized_required in atomic_plane_disable
flag immediately after it is set in atomic_plane_disconnect, causing us to
never have flag set during next flip in UpdatePlanes.
[how]
Optimize directly after each time plane is removed.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
TRAINING_AUX_RD_INTERVAL (DPCD 000Eh) modifies the read interval
for the EQ training sequence. CR read interval should remain 100 us.
Currently, the CR interval is also being modified.
[HOW]
lt_settings->cr_pattern_time should always be 100 us.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are shared regs and code across DCN generations. Pull them out
into a shared common location.
Also, expose some dcn20 init functions.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fixes issue when we have a display connected using a passive
dongle and then emulate over it using a DP connection at 1 x 1.62 Ghz.
System hangs because register bus returns back 0xFFFFFFFF for all
register reads after setting register DIG_BE_CNTL in
dcn10_link_encoder_connect_dig_be_to_fe(). Hang occurs later
when trying to do a register read.
[How]
At the start of the emulation, dc_link_set_preferred_link_settings()
and dp_retrain_link_dp_test() is called, even though it is connected
using a passive dongle.
Add an extra condition in dp_retrain_link_dp_test() to check for
link->dongle_max_pix_clk > 0. This is the only way we know if the
connection is using passive dongle so we don't retrain DP.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently logical values are swapped in HW, causing
system aperture to be undefined, so VA and PA cannot co-exist
[how]
program values correctly
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
'second_line_offset_adj' was mistakenly left at zero, even though DSC spec
v1.2a recommends setting this field to 512 for 4:2:0.
[how]
Set 'second_line_offset_adj' to 512 for 4:2:0 and leave at zero otherwise
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We're not expected to enter the default case, but not returning a
default value here is incorrect.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unintentionally introduced behaviour change from previous refactor,
which causes clks to be 0 in no stream cases, which will cause
divide by 0.
[How]
Skip calculation of clocks when no stream. Which is the same as old
behaviour.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some parts of the DSC spec relating to 4.2.0 were not reflected in
drm_dsc_compute_rc_parameters, causing unexpected config failures
[How]
Add nsl_bpg_offset and rbs_min computation
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dce was re-arch'd, therefore adding aux tracing log into new dce
[How]
The porting from submit_channel_request/process_channel_reply of aux_engine_dce110.c
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <tong.cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are certain MST displays (i.e. Dell P2715Q)
that although have the MST feature set to off may still
report it is a branch device and a non-zero
value for downstream port present.
This can lead to us incorrectly classifying a
dp dongle connection as being active and
disabling the audio endpoint for the display.
[How]
Modified the placement and
condition used to assign
the is_branch_dev bit.
Signed-off-by: Harmanprit Tatla <harmanprit.tatla@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Due to limitation in SMU/PPLIB, it is not possible to know Fmax @ Vmin for DCFCLK.
This causes issues at high display configurations where extra headroom of DCFCLK
can enable P-state switching
[how]
Use existing override logic. If override not defined, then force
min = 507
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For better readability and reusability
[How]
Move snippets of BW calculation code into helpers.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A regression caused dsc to never get disabled in certain situations.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some values were not being converted or bit-shifted properly for
HW registers, causing black screen
[how]
Fix up the values before programming HW
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To add support for OS requirement to set preferred link training
parameters.
[HOW]
Create new structure of dp link training overrides. During link training
processes, these values should be used instead of the default training
parameters.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On some modes SMU will be in infinite loop state at boot, this is
because driver assumes p_state_support is false, but this is the
opposite of the assumed boot state by SMU. we optimize away
notifying SMU about no pstate, and so they will get stuck
[how]
when we init clk manager, init pstate to true, so it matches driver load
assumption
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we are using the signed FW now, and also using PSP firmware loading,
but it's still potential to break driver when loading FW directly
instead of PSP, so we should add offset.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In function __ttm_dma_alloc_page(), d_page->addr is allocated
by dma_alloc_attrs() but freed with use dma_free_coherent() in
__ttm_dma_free_page().
Use the correct dma_free_attrs() to free d_page->vaddr.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2:
set average clock value on level 1 when current clock equal
min or max clock (fine grained dpm support).
the navi10 gfxclk (sclk) support fine grained DPM,
so use level 1 to show current dpm freq in sysfs pp_dpm_xxx
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
this function is not needed any more. error injection is
the only way to validate ras but it can't be executed in
amdgpu_ras_init, where gpu is even not initialized
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
error injection to other IP blocks (except UMC) will be enabled
until RAS feature stablize on those IP blocks
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX RAS has not been stablized yet. disable GFX ras until
it is fully funcitonal.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With gfxclk or uclk dpm disabled, it's reasonable to report bootup clock
as the max supported.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The GDS and GWS blocks default to allowing all VMIDs to
access all entries. Graphics VMIDs can handle setting
these limits when the driver launches work. However,
compute workloads under HWS control don't go through the
kernel driver. Instead, HWS firmware should set these
limits when a process is put into a VMID slot.
Disable access to these devices by default by turning off
all mask bits (for OA) and setting BASE=SIZE=0 (for GDS
and GWS) for all compute VMIDs. If a process wants to use
these resources, they can request this from the HWS
firmware (when such capabilities are enabled). HWS will
then handle setting the base and limit for the process when
it is assigned to a VMID.
This will also prevent user kernels from getting 'stuck' in
GWS by accident if they write GWS-using code but HWS
firmware is not set up to handle GWS reset. Until HWS is
enabled to handle GWS properly, all GWS accesses will
MEM_VIOL fault the kernel.
v2: Move initialization outside of SRBM mutex
Signed-off-by: Joseph Greathouse <Joseph.Greathouse@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
