Update VDD_SOC voltage to 1.25V for 900MHz operating point
according to datasheet Rev. 1.3, 08/2018, 25mV is added to
the minimum allowed values to cover power supply ripple.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This board, as well as some other boards with i.MX6 and a PMIC, uses a
"PMIC_STBY_REQ" line to notify the PMIC about a state change.
The PMIC is programmed for a specific state change before triggering the
line.
In this case, PMIC_STBY_REQ can be used for stand by, sleep
and power off modes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinctrl properties on the IOMUXC node get overwritten by the
carrier board level device tree, hence the pinctrl_reset_moci
pinctrl does not get applied.
Associate the pinctrl_reset_moci pinctrl with the PCIe node where
we also make use of the pin as a reset GPIO.
Since the pin is muxed as a GPIO by default not muxing it explicitly
worked fine in practise.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to keep the PMU disabled.
Enable it like it is done in the other i.MX dtsi files.
With this change applied we see:
[ 1.338866] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board typically has 2 populated SFF interfaces. The mv88e6xxx
driver currently supports SFF modules connected to ports 9 and 10 of
the mv88e6390. Add support for sff2, which is connected to port 9.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The switch has an SFF attached to port 5. Add the SFF device, the
pinmux for its GPIOs, and list the port in the switch configuration.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
NOR and IFC controller connectivity is big-endian.
So add big-endian field in nor device tree node allowing
IFC controller to read/write data from/to the flash correctly.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6ULL is a lite version of i.MX6UL, its full name
is i.MX6 UltraLiteLite, NOT UlltraLite.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SLL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signals available on both i.MX6UL and i.MX6ULL should have the same name
because it is the case of all others common signals, it avoids to make
mistakes (use the wrong ones) and it makes writing device tree files
less complicated. For example:
imx6ul-imx6ull-board.dtsi:
...
pinctrl_uart5: uart5grp {
fsl,pins = <
MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX 0x1b0b1
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX 0x1b0b1
>;
};
imx6ul-board.dts:
#include <imx6ul.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
imx6ull-board.dts:
#include <imx6ull.dtsi>
#include <imx6ul-imx6ull-board.dtsi>
...
Without this patch, the imx6ull-board.dtb will use
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX instead of
MX6ULL_PAD_UART5_RX_DATA__UART5_DCE_RX and the uart5 will be
misconfigured.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Setting a stdout-path in the .dtb is convenient because then the user
gets a serial console on the RS-232 connector without any extra effort
of figuring out the relevant 'console=' boot parameter.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WaRP7 has one mikroBUS socket on the back to plug click boards.
This patch allows to interact with some of these
i2c modules (EEPROM, RTC and so on).
Signed-off-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "EDIMM STARTER KIT i.Core 1.5 MIPI Evaluation" is based on the 1.5 version
of the i.Core MX6 cpu module. The 1.5 version differs from the original one for
a few details, including the ethernet PHY interface clock provider.
With this commit, the ethernet interface works properly:
SMSC LAN8710/LAN8720 2188000.ethernet-1:00: attached PHY driver
While before using the 1.5 version, ethernet failed to startup do to un-clocked
PHY interface:
fec 2188000.ethernet eth0: could not attach to PHY
Fixes: 3fe0883577 ("ARM: dts: imx6q: Add Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit support")
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 1.5 version of Engicam's i.Core MX6 CPU module features a different clock
provider for the ethernet's PHY interface. Adjust the FEC ptp clock to
reference CLK_ENET_REF clock source, and set SION bit of
MX6QDL_PAD_GPIO_16__ENET_REF_CLK to adjust the input path of that pin.
The newly introduced imx6ql-icore-1.5.dtsi allows to collect in a single
place differences between version '1.0' and '1.5' of the module.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move usdhc2 and gpmi along with pinctrl nodes on
imx6ul-isiot.dtsi from dts files and mark it as 'disabled'
and the relevant dts will enable the status as 'okay'
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Define the Messaging Unit (MU) for i.MX7 in the processor's dtsi.
The respective driver is added in the next commit.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7ULP B0 chip has some pin changes for USB and VIU
module, update pinfunc header file accordingly.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The MC13892 Analog-to-Digital input pins (ADIN5-7) are exposed on the
imx51-babbage board.
Pass the "fsl,mc13xxx-uses-adc" property so that the MC13892 ADC
block can work.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX6SLL pinctrl driver, for details, please refer to
Documentation/devicetree/bindings/gpio/gpio.txt of "gpio-ranges"
property.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
-----BEGIN PGP SIGNATURE-----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=CHc2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants against v4.19-rc1
These are mostly fixes related to using ti-sysc interconnect target module
driver for accessing right register offsets for sgx and cpsw and for
no_console_suspend regression.
There is also a droid4 emmc fix where emmc may not get detected for some
models, and vibrator dts mismerge fix.
And we have a file permission fix for am335x-osd3358-sm-red.dts that
just got added. And we must tag RTC as system-power-controller for
am437x for PMIC to shut down during poweroff.
* tag 'omap-for-v4.19/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Fix emmc errors seen on some devices
ARM: dts: Fix file permission for am335x-osd3358-sm-red.dts
arm: dts: am4372: setup rtc as system-power-controller
ARM: dts: omap4-droid4: fix vibrations on Droid 4
bus: ti-sysc: Fix no_console_suspend handling
bus: ti-sysc: Fix module register ioremap for larger offsets
ARM: OMAP2+: Fix module address for modules using mpu_rt_idx
ARM: OMAP2+: Fix null hwmod for ti-sysc debug
Signed-off-by: Olof Johansson <olof@lixom.net>
Otherwise we can get the following errors occasionally on some devices:
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 14329
...
I have one device that hits this error almost on every boot, and another
one that hits it only rarely with the other ones I've used behave without
problems. I'm not sure if the issue is related to a particular eMMC card
model, but in case it is, both of the machines with issues have:
# cat /sys/class/mmc_host/mmc1/mmc1:0001/manfid \
/sys/class/mmc_host/mmc1/mmc1:0001/oemid \
/sys/class/mmc_host/mmc1/mmc1:0001/name
0x000045
0x0100
SEM16G
and the working ones have:
0x000011
0x0100
016G92
Note that "ti,non-removable" is different as omap_hsmmc_reg_get() does not
call omap_hsmmc_disable_boot_regulators() if no_regulator_off_init is set.
And currently we set no_regulator_off_init only for "ti,non-removable" and
not for "non-removable". It seems that we should have "non-removable" with
some other mmc generic property behave in the same way instead of having to
use a non-generic property. But let's fix the issue first.
Fixes: 7e2f8c0ae6 ("ARM: dts: Add minimal support for motorola droid 4
xt894")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix wrong mode for dts file added by commit bb3e3fbbac
("ARM: dts: Add DT support for Octavo Systems OSD3358-SM-RED
based on TI AM335x").
Signed-off-by: Neeraj Dantu <neeraj.dantu@octavosystems.com>
CC: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
imx23-evk board has a Seiko 43WVF1G parallel display.
Instead of hardcoding the display timings in the device tree, use
the "sii,43wvf1g" compatible instead.
This aligns with the new mxsfb bindings scheme documented at:
Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended to place regulators outside simple-bus, so move them
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx28-evk board has a Seiko 43WVF1G parallel display.
Instead of hardcoding the display timings in the device tree, use
the "sii,43wvf1g" compatible instead.
This aligns with the new mxsfb bindings scheme documented at:
Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended to place regulators outside simple-bus, so move them
accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 1c86c9dd82.
That commit followed the reference manual but unfortunately the imx7d
manual is incorrect.
Tested with ath9k pcie card and confirmed internally.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 1c86c9dd82 ("ARM: dts: imx7d: Invert legacy PCI irq mapping")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Merge yet more updates from Andrew Morton:
- the rest of MM
- various misc fixes and tweaks
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
mm: Change return type int to vm_fault_t for fault handlers
lib/fonts: convert comments to utf-8
s390: ebcdic: convert comments to UTF-8
treewide: convert ISO_8859-1 text comments to utf-8
drivers/gpu/drm/gma500/: change return type to vm_fault_t
docs/core-api: mm-api: add section about GFP flags
docs/mm: make GFP flags descriptions usable as kernel-doc
docs/core-api: split memory management API to a separate file
docs/core-api: move *{str,mem}dup* to "String Manipulation"
docs/core-api: kill trailing whitespace in kernel-api.rst
mm/util: add kernel-doc for kvfree
mm/util: make strndup_user description a kernel-doc comment
fs/proc/vmcore.c: hide vmcoredd_mmap_dumps() for nommu builds
treewide: correct "differenciate" and "instanciate" typos
fs/afs: use new return type vm_fault_t
drivers/hwtracing/intel_th/msu.c: change return type to vm_fault_t
mm: soft-offline: close the race against page allocation
mm: fix race on soft-offlining free huge pages
namei: allow restricted O_CREAT of FIFOs and regular files
hfs: prevent crash on exit from failed search
...
Almost all files in the kernel are either plain text or UTF-8 encoded. A
couple however are ISO_8859-1, usually just a few characters in a C
comments, for historic reasons.
This converts them all to UTF-8 for consistency.
Link: http://lkml.kernel.org/r/20180724111600.4158975-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms@verge.net.au> [IPVS portion]
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> [IIO]
Acked-by: Michael Ellerman <mpe@ellerman.id.au> [powerpc]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----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=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
RTC alarm2 is connected to pmic_en line and hence can be used to control
the pmic enabling/disabling. Hence add the system-power-controller for rtc
node.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Vibration GPIOs don't have anything to do with wakeup. Move it to
normal section; this fixes vibrations on Droid 4.
Fixes: a5effd9683 ("ARM: dts: omap4-droid4: Add vibrator")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
- New support for the ASPEED USB host controller and USB vhub (device)
support
- Descriptions for the ColdFire processor that is part of the ASPEED
SoC
- Small fixes:
* pwm/tach clock
-----BEGIN PGP SIGNATURE-----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=aigP
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.19-devicetree-no-fsi' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
ASPEED device tree updates for 4.19
- New support for the ASPEED USB host controller and USB vhub (device)
support
- Descriptions for the ColdFire processor that is part of the ASPEED
SoC
- Small fixes:
* pwm/tach clock
* tag 'aspeed-4.19-devicetree-no-fsi' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: aspeed: Add coprocessor interrupt controller
ARM: dts: aspeed: Use 24MHz fixed clock for pwm
ARM: dts: aspeed: Fix Romulus VGA frame buffer
ARM: dts: aspeed: Enable vhub on port A of AST2500 EVB
ARM: dts: aspeed: Add G5 USB Virtual Hub
ARM: dts: aspeed: Add G4 USB Virtual Hub
ARM: dts: aspeed: Add G5 USB host pinmux
ARM: dts: aspeed: Add G4 USB pinmux
Signed-off-by: Olof Johansson <olof@lixom.net>
Our usual bunch of changes shared between arm and arm64.
This time, we have:
- eMMC support for the ALL-H3-CC boards
- EMAC support for the Beelink X2
-----BEGIN PGP SIGNATURE-----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=Blyi
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 changes for 4.19
Our usual bunch of changes shared between arm and arm64.
This time, we have:
- eMMC support for the ALL-H3-CC boards
- EMAC support for the Beelink X2
* tag 'sunxi-h3-h5-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi-h3-h5: Remove unused address-cells/size-cells of dwmac-sun8i
ARM: dts: sunxi: libretech-all-h3-cc: Enable eMMC module
ARM: sun8i: h3: add SY8113B regulator on Banana Pi M2 Zero board
ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2
ARM: dts: sun8i-h3: Add missing cooling device properties for CPUs
Signed-off-by: Olof Johansson <olof@lixom.net>
