Only the ad778x have the 'gain' status bit. Check it before updating
through a new variable is_ad778x in chip_info.
Signed-off-by: Giuliano Belinassi <giuliano.belinassi@usp.br>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The RD/WR pin and CONVST pin are logical inputs to the AD78xx
chip as per the datasheet. Hence convert them to outputs.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
AD7818 does not support busy_pin functionality as per datasheet.
Hence drop busy_pin when AD7818 is used.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Channel 6 of the SAR ADC can be switched between two inputs:
SAR_ADC_CH6 input (an actual pad on the SoC) and the signal from the
temperature sensor inside the SoC.
To get usable results from the temperature sensor we need to read the
corresponding calibration data from the eFuse and pass it to the SAR ADC
registers. If the temperature sensor is not calibrated (the eFuse data
contains a bit for this) then the driver will only register the
iio_chan_spec's for voltage measurements.
This only enables the temperature sensor for the Meson8 SoC. Meson8b and
Meson8m2 SoCs can be supported in the future as well but we first need
a way to pass the fifth TSC (temperature sensor coefficient) bit to the
HHI register area (apart from that the infrastructure as already
implemented for Meson8 can be used). On the 64-bit SoCs (GXBB, GXL and
GXM) the temperature sensor inside SAR ADC is firmware-controlled (by
BL30, we can simply use the SCPI hwmon driver to get the chip
temperature).
To keep the devicetree interface backwards compatible we simply skip the
temperature sensor initialization if no eFuse nvmem cell is passed via
devicetree.
The public documentation for the SAR ADC IP block does not explain how
to use the registers to read the temperature. The logic from this patch
is based on reading and understanding Amlogic's GPL kernel sources.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 32-bit Meson8 SoC can use the SAR ADC to read the chip temperature.
This requires setting the correct TSC (temperature sensor coefficient),
which is programmed into the eFuse during the manufacturing process.
Meson8b and Meson8m2 are not supported yet because they have a 5-bit TSC
and only the first four bits are stored inside the SAR ADC registers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds a channel type check at the beginning of the
ad2s90_read_raw function. Since ad2s90 has only one channel, it just
checks if the given channel is the expected one and if not, return
-EINVAL.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds the IIO_CHAN_INFO_SCALE mask to ad2s90_chan and
implements the relative read behavior at ad2s90_read_raw.
Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously, devm_iio_device_register was being called before the
spi_setup call and the spi_device's max_speed_hz and mode assignments.
This could lead to a race condition since the driver was still being
set up after it was already made ready to use. To fix it, this patch
moves the device registration to the end of ad2s90_probe.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch removes an initial assignment to the variable ret at probe,
that was always overwritten.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously, ad2s90_probe ignored the return code from spi_setup, not
handling its possible failure. This patch makes ad2s90_probe check if
the code is an error code and, if so, do the following:
- Call dev_err with an appropriate error message.
- Return the spi_setup's error code.
Note: The 'return ret' statement could be out of the 'if' block, but
this whole block will be moved up in the function in the patch:
'staging:iio:ad2s90: Move device registration to the end of probe'.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously, when spi_read returned an error code inside ad2s90_read_raw,
the code was ignored and IIO_VAL_INT was returned. This patch makes the
function return the error code returned by spi_read when it fails.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Variable val subtracted an uninitialized value on IIO_CHAN_INFO_OFFSET.
This was fixed by assigning the correct value instead.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add device tree table for matching vendor ID.
Note that as the driver is still heavily in flux and there are some
non obvious aspects to a comprehensive binding, that binding will
be submitted at a later date (before leaving staging!)
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop gpioin flag which decides how the GPIOs
are controlled as the GPIOs must be outputs
for the host as per the datasheet.
Removes need for platform data so that is dropped as well.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the gpiod interface instead of the deprecated old non-descriptor
interface.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Report the step range of the respective potentiometers that are
possible to userspace.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Description how to invoke ti-dac7311 driver from device tree file.
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It is a driver for Texas Instruments 8/10/12-bit 1-channel
compatible with DAC6311 and DAC5311 chips.
Datasheet of this chip:
http://www.ti.com/lit/ds/symlink/dac7311.pdf
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add DT binding documentation for the LSM9DS1 magnetometer.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The type promotion will kick in, so the comparison will work.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LIS3MDL and LSM9DS1 are missing BDU settings in their register maps, so add
them. I don't have a LIS3MDL sensor to test, but this works correctly on
the LSM9DS1, which has the same register map.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Update the sensor settings to support the LSM9DS1 sensor. Although the
LSM9DS1 accelerometer and gyroscope are coupled together to use the same
FIFO, the magnetometer is separate and can be cleanly supported without
refactoring the existing driver.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a comment clarifying better when to use <device_name> vs
<device_name>-magn in compatibility strings.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
More concise to have a pointer to tpl0102_cfg struct in the iio_priv
data than an integer to an index of an array.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Reviewed-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Description how to invoke ad7949 driver from device tree file.
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Compatible with AD7682 and AD7689 chips.
It is a Analog Devices ADC driver 14/16 bits 4/8 channels
with SPI protocol
Datasheet of the device:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD7949.pdf
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the checkpatch.pl warning:
WARNING: Blank lines aren't necessary before a close brace '}'
Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes the checkpatch.pl warning:
WARNING: No space is necessary after a cast
Signed-off-by: Victor Colombo <victorcolombo@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This updates the ti-adc128s052.c file to use SPDX-License-Identifier
instead of more verbose license text.
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI _HID AANT1280 matches an ADC124S101 present on E3940 SKUs of the UP
Squared board.
Add it to the driver.
Signed-off-by: Nicola Lunghi <nicola.lunghi@emutex.com>
[javier@emutex.com: fix up commit message and one checkpatch warning]
Signed-off-by: Javier Arteaga <javier@emutex.com>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The datasheets for ADC122S021 and ADC124S021 list two more
pin-compatible alternatives for each device.
Add their IDs as compatible strings.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Javier Arteaga <javier@emutex.com>
Signed-off-by: Dan O'Donovan <dan@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the gpiod interface for rdwr_pin, convert_pin and busy_pin
instead of the deprecated old non-descriptor interface.
Note that Phil Reid identified that some of this code would never
have worked. A follow up patch can fix that as this is just
a direct change of interface.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Static analysis with CoverityScan is throwing warnings that specific
case statements are missing breaks. Rather than adding breaks, add
return -EINVAL to the specific case statements to clarify the
error return paths. Fix also saves 50 bytes.
Before:
text data bss dec hex filename
21418 4936 128 26482 6772 drivers/iio/adc/ina2xx-adc.o
After:
dec hex filename
21370 4936 128 26434 6742 drivers/iio/adc/ina2xx-adc.o
(gcc 8.2, x86-64)
Detected by CoverityScan, CID#1462408 ("Missing break in switch")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Change close parenthesis alignment to match respective open parenthesis at
iio/drivers/staging/iio/adc/ad7606.c line 379.
This makes the file more compliant with the preferred coding style for the
linux kernel.
Signed-of-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Miscellaneous cleanup to fix minor consistency, grammar, and spelling
issues.
Signed-off-by: Martin Kelly <martin@martingkelly.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The custom build function ad7280_crc8_build_table is not needed. The
crc8_populate_msb function from linux/crc8.h will build the same crc
table.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Inside __ad7280_read32(), the spi_sync_transfer() can fail with negative
error code. This change will ensure that this error is being passed up
in the call stack, so it can be handled.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
So user could specify outside CFLAGS values.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add KIOX0009 ACPI HID, this is used e.g. on the Acer One 10.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes most "Alignment should match open parenthesis" check
warnings found by checkpatch.pl in the addac/adt7316 driver.
Signed-off-by: Renato Lui Geh <renatogeh@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced "...and fall through."
with the specific string "fall through", which is what GCC is
expecting to find thus supressing this false positive.
As Peter has observed this breaks the nice English flow, which is
less than ideal, but short of teaching GCC to read English, there
isn't a lot that we can do about it.
Addresses-Coverity-ID: 1462408 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fixes all "Assignment operator '=' should be on the previous
line" checks found in ad2s1210.c with checkpatch.pl.
Signed-off-by: Matheus Tavares <matheus.bernardino@usp.br>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These lines were misaligned, but the checkpatch.pl didn't indicate them
as such.
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
By using the copy of channel attribute, we can now make the lines short
enough to eliminate the checkpatch.pl problem:
CHECK: Alignment should match open parenthesis
Signed-off-by: Slawomir Stepien <sst@poczta.fm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The charme of devm_* functions is that you don't need to care about them
in the error path. In this case it is valid to just return NULL which makes
the device fail to probe and then the two gpios and the allocated memory
are freed automatically by the driver core.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The checkpatch script doesn't like camel-case names.
Renamed the variable.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix the F: entry in MAINTAINERS file, point it to the correct file.
While at it, add DT binding doc F: entry too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This satisfies a checkpatch warning and is the preferred
method for notating the license.
The SPDX identifier is a legally binding shorthand, which
can be used instead of the full boiler plate text.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replacing all occurrences of (1<<x) with BIT(x) to fix checkpatch issue.
CHECK:Prefer using the BIT macro
Signed-off-by: Mamta Shukla <mamtashukla555@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
