Although not strictly necessary, it is customary to reverse the order in
which we release locks that we acquire. This helps preserve lock
ordering during future refactors, which can help avoid potential
deadlock situations.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop overloading the __I40EVF_IN_CRITICAL_TASK bit lock to protect the
mac_filter_list and vlan_filter_list. Instead, implement a spinlock to
protect these two lists, similar to how we protect the hash in the i40e
PF code.
Ensure that every place where we access the list uses the spinlock to
ensure consistency, and stop holding the critical section around blocks
of code which only need access to the macvlan filter lists.
This refactor helps simplify the locking behavior, and is necessary as
a future refactor to the __I40EVF_IN_CRITICAL_TASK would cause
a deadlock otherwise.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In i40evf_reset_task we use netif_running() to determine whether or not
the device is currently up. This allows us to properly free queue memory
and shut down things before we request the hardware reset.
It turns out that we cannot be guaranteed of netif_running() returning
false until the device is fully up, as the kernel core code sets
__LINK_STATE_START prior to calling .ndo_open. Since we're not holding
the rtnl_lock(), it's possible that the driver's i40evf_open handler
function is currently being called while we're resetting.
We can't simply hold the rtnl_lock() while checking netif_running() as
this could cause a deadlock with the i40evf_open() function.
Additionally, we can't avoid the deadlock by holding the rtnl_lock()
over the whole reset path, as this essentially serializes all resets,
and can cause massive delays if we have multiple VFs on a system.
Instead, lets just check our own internal state __I40EVF_RUNNING state
field. This allows us to ensure that the state is correct and is only
set after we've finished bringing the device up.
Without this change we might free data structures about device queues
and other memory before they've been fully allocated.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Display some more stats that were already being counted, to help users
understand when priority xon/xoff packets are being sent/received
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The commit e817f85652 ("xdp: generic XDP handling of xdp_rxq_info")
removed some ifdef CONFIG_SYSFS in net/core/dev.c, but forgot to
remove the corresponding ifdef's in include/linux/netdevice.h.
Fixes: e817f85652 ("xdp: generic XDP handling of xdp_rxq_info")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHYs in the mv88e6390 switch have a temperature sensor.
It uses a different register layout to other PHY currently supported.
It also has an errata, in that some reads of the sensor result in bad
values. So a number of reads need to be made, and the average taken.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Gospodarek says:
====================
net: create dynamic software irq moderation library
This converts the dynamic interrupt moderation library from the mlx5e
driver into a library so it can be used by any driver. The penultimate
patch in this set adds support for this new dynamic interrupt moderation
library in the bnxt_en driver and the last patch creates an entry in the
MAINTAINERS file for this library.
The main purpose of this code is to allow an administrator to make sure
that default coalesce settings are optimized for low latency, but
quickly adapt to handle high throughput/bulk traffic by altering how
much time passes before popping an interrupt.
For any new driver the following changes would be needed to use this
library:
- add elements in ring struct to track items needed by this library
- create function that can be called to actually set coalesce settings
for the driver
Credit to Rob Rice and Lee Reed for doing some of the initial proof of
concept and testing for this patch and Tal Gilboa and Or Gerlitz for
their comments, etc on this set.
v4: Fix build breakage for VF representers noticed by kbuild test robot.
Thanks for being so courteous, kbuild test robot!
v3: bnxt_en fix from Michael Chan, comment suggestion from Vasundhara
Volam, and small mlx5e header file fix from Tal Gilboa.
v2: Spelling fixes from Stephen Hemminger, bnxt_en suggestions from
Michael Chan, spelling and formatting fixes from Or Gerlitz, and
spelling and mlx5e changes suggested by Tal Gilboa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the changes needed for the bnxt_en driver to add support
for dynamic interrupt moderation per ring.
This does add additional counters in the receive path, but testing shows
that any additional instructions are offset by throughput gain when the
default configuration is for low latency.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the arguments net_dim() by formatting them into a struct
net_dim_sample before calling the function.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Suggested-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This move allows drivers to add private structure elements to track the
number of packets, bytes, and interrupts events per ring. A driver
also defines a workqueue handler to act on this collected data once per
poll and modify the coalescing parameters per ring.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change all appropriate mlx5_am* and MLX5_AM* references to net_dim and
NET_DIM, respectively, in code that handles dynamic interrupt
moderation. Also change all references from 'am' to 'dim' when used as
local variables and add generic profile references.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions were identified as ones that could be made generic and
used by multiple drivers. Most of the contents of en_rx_am.c are moved
to net_dim.c.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More movement to help make this code more generic.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes mlx5e_am_sample more generic so that it can be called easily
from a driver that does not use the same data structure to store these
values in a single structure.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move these to newly created file to prepare to move these functions to a
library.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create new header file to prepare to move code that handles irq
moderation to a library that lives in a header file.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Tal Gilboa <talgi@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
ipv6: Add support for non-equal-cost multipath
This set aims to add support for IPv6 non-equal-cost multipath routes.
The first three patches convert multipath selection to use the
hash-threshold method (RFC 2992) instead of modulo-N. The same method is
employed by the IPv4 routing code since commit 0e884c78ee ("ipv4: L3
hash-based multipath").
Unlike modulo-N, with hash-threshold only the flows near the region
boundaries are affected when a nexthop is added or removed. In addition,
it allows us to easily add support for non-equal-cost multipath in the
last patch by sizing the different regions according to the provided
weights.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of hash-threshold instead of modulo-N makes it trivial to add
support for non-equal-cost multipath.
Instead of dividing the multipath hash function's output space equally
between the nexthops, each nexthop is assigned a region size which is
proportional to its weight.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that each nexthop stores its region boundary in the multipath hash
function's output space, we can use hash-threshold instead of modulo-N
in multipath selection.
This reduces the number of checks we need to perform during lookup, as
dead and linkdown nexthops are assigned a negative region boundary. In
addition, in contrast to modulo-N, only flows near region boundaries are
affected when a nexthop is added or removed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hash thresholds assigned to IPv6 nexthops are in the range of
[-1, 2^31 - 1], where a negative value is assigned to nexthops that
should not be considered during multipath selection.
Therefore, in a similar fashion to IPv4, we need to use the upper
31-bits of the multipath hash for multipath selection.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we convert IPv6 to use hash-threshold instead of modulo-N, we
first need each nexthop to store its region boundary in the hash
function's output space.
The boundary is calculated by dividing the output space equally between
the different active nexthops. That is, nexthops that are not dead or
linkdown.
The boundaries are rebalanced whenever a nexthop is added or removed to
a multipath route and whenever a nexthop becomes active or inactive.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tries to batched used ring update during RX. This is pretty
fit for the case when guest is much faster (e.g dpdk based
backend). In this case, used ring is almost empty:
- we may get serious cache line misses/contending on both used ring
and used idx.
- at most 1 packet could be dequeued at one time, batching in guest
does not make much effect.
Update used ring in a batch can help since guest won't access the used
ring until used idx was advanced for several descriptors and since we
advance used ring for every N packets, guest will only need to access
used idx for every N packet since it can cache the used idx. To have a
better interaction for both batch dequeuing and dpdk batching,
VHOST_RX_BATCH was used as the maximum number of descriptors that
could be batched.
Test were done between two machines with 2.40GHz Intel(R) Xeon(R) CPU
E5-2630 connected back to back through ixgbe. Traffic were generated
on one remote ixgbe through MoonGen and measure the RX pps through
testpmd in guest when do xdp_redirect_map from local ixgbe to
tap. RX pps were increased from 3.05 Mpps to 4.00 Mpps (about 31%
improvement).
One possible concern for this is the implications for TCP (especially
latency sensitive workload). Result[1] does not show obvious changes
for most of the netperf test (RR, TX, and RX). And we do get some
improvements for RX on some specific size.
Guest RX:
size/sessions/+thu%/+normalize%
64/ 1/ +2%/ +2%
64/ 2/ +2%/ -1%
64/ 4/ +1%/ +1%
64/ 8/ 0%/ 0%
256/ 1/ +6%/ -3%
256/ 2/ -3%/ +2%
256/ 4/ +11%/ +11%
256/ 8/ 0%/ 0%
512/ 1/ +4%/ 0%
512/ 2/ +2%/ +2%
512/ 4/ 0%/ -1%
512/ 8/ -8%/ -8%
1024/ 1/ -7%/ -17%
1024/ 2/ -8%/ -7%
1024/ 4/ +1%/ 0%
1024/ 8/ 0%/ 0%
2048/ 1/ +30%/ +14%
2048/ 2/ +46%/ +40%
2048/ 4/ 0%/ 0%
2048/ 8/ 0%/ 0%
4096/ 1/ +23%/ +22%
4096/ 2/ +26%/ +23%
4096/ 4/ 0%/ +1%
4096/ 8/ 0%/ 0%
16384/ 1/ -2%/ -3%
16384/ 2/ +1%/ -4%
16384/ 4/ -1%/ -3%
16384/ 8/ 0%/ -1%
65535/ 1/ +15%/ +7%
65535/ 2/ +4%/ +7%
65535/ 4/ 0%/ +1%
65535/ 8/ 0%/ 0%
TCP_RR:
size/sessions/+thu%/+normalize%
1/ 1/ 0%/ +1%
1/ 25/ +2%/ +1%
1/ 50/ +4%/ +1%
64/ 1/ 0%/ -4%
64/ 25/ +2%/ +1%
64/ 50/ 0%/ -1%
256/ 1/ 0%/ 0%
256/ 25/ 0%/ 0%
256/ 50/ +4%/ +2%
Guest TX:
size/sessions/+thu%/+normalize%
64/ 1/ +4%/ -2%
64/ 2/ -6%/ -5%
64/ 4/ +3%/ +6%
64/ 8/ 0%/ +3%
256/ 1/ +15%/ +16%
256/ 2/ +11%/ +12%
256/ 4/ +1%/ 0%
256/ 8/ +5%/ +5%
512/ 1/ -1%/ -6%
512/ 2/ 0%/ -8%
512/ 4/ -2%/ +4%
512/ 8/ +6%/ +9%
1024/ 1/ +3%/ +1%
1024/ 2/ +3%/ +9%
1024/ 4/ 0%/ +7%
1024/ 8/ 0%/ +7%
2048/ 1/ +8%/ +2%
2048/ 2/ +3%/ -1%
2048/ 4/ -1%/ +11%
2048/ 8/ +3%/ +9%
4096/ 1/ +8%/ +8%
4096/ 2/ 0%/ -7%
4096/ 4/ +4%/ +4%
4096/ 8/ +2%/ +5%
16384/ 1/ -3%/ +1%
16384/ 2/ -1%/ -12%
16384/ 4/ -1%/ +5%
16384/ 8/ 0%/ +1%
65535/ 1/ 0%/ -3%
65535/ 2/ +5%/ +16%
65535/ 4/ +1%/ +2%
65535/ 8/ +1%/ -1%
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVF5WAAoJEEg/ir3gV/o+fRkH/0PxjwJRA3REqhi/H8HOdH9f
cBLrOzFdqTCYQWQFCLFbMQ/Zgoel3KglpJ0iQMjuVFfjMbybVXOe8FAEVdbWHnfL
C+2HRMe8dplKrsq5UkxJhbyKhFKhl2XeMFYWonw9dSM7Nz5DyowQ1y1r5SgMlMAv
t3mYAIa4kZHK18BjDoIsCoAXXwsHiztR2irMp5+DwataTGP7vC7AsrucDxLA/qFf
I3E15DZk9s1f53PUuY7CYnUnJfMMP3VJdxpyx4k6xt9J2IMuilF4YyD6wpAKsVQU
/LzRkWI9x/6QindffqlrACeeidimOeY4pC4txIhS5uXgFXulugDHq1/Ih1sgZS8=
=g5vr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2018-01-08
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Peng Li says:
====================
code improvements in HNS3 driver
This patchset fixes 2 comments for community review.
[patch 1/2] reverts "net: hns3: Add packet statistics of netdev"
reported by Jakub Kicinski and David Miller.
[patch 2/2] reports the function type the same line with
hns3_nic_get_stats64, reported by Andrew Lunn.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function type should be on the same line with the function
name, or it may cause display error if a patch edit the
function. There is am example following:
https://www.spinics.net/lists/netdev/msg476141.html
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8491000754.
It is duplicate to add statistics of netdev for ethtool -S.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jassi Brar says:
====================
Socionext Synquacer NETSEC driver
Changes since v5
# Removed helper macros
# Removed 'inline' qualifier
# Changed multiline empty comment to single line
# Added 'clock-names' property in DT binding example
# Ignore 'clock-names' property in driver until f/ws in the wild are
upgraded or we support instance that take in more than one clock.
# Rebased the patchset onto net-next
Changes since v4
# Fixed ucode indexing as a word, instead of byte
# Removed redundant clocks, keep only phy rate reference clock
and expect it to be 'phy_ref_clk'
Changes since v3
# Discard 'socionext,snq-mdio', and simply use 'mdio' subnode.
# Use ioremap on ucode region as well, instead of memremap.
Changes since v2
# Use 'mdio' subnode in DT bindings.
# Use phy_interface_mode_is_rgmii(), instead of open coding the check.
# Use readl/b with eeprom_base pointer.
# Unregister mdio bus upon failure in probe.
Changes since v1
# Switched from using memremap to ioremap
# Implemented ndo_do_ioctl callback
# Defined optional 'dma-coherent' DT property
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entry for the Socionext Netsec controller driver and DT bindings.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver adds support for Socionext "netsec" IP Gigabit
Ethernet + PHY IP used in the Synquacer SC2A11 SoC.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for Device-Tree bindings for the
Socionext NetSec Controller driver.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-01-09
This series contains updates to ixgbe and ixgbevf only.
Emil fixes an issue with "wake on LAN"(WoL) where we need to ensure we
enable the reception of multicast packets so that WoL works for IPv6
magic packets. Cleaned up code no longer needed with the update to
adaptive ITR.
Paul update the driver to advertise the highest capable link speed
when a module gets inserted. Also extended the displaying of firmware
version to include the iSCSI and OEM block in the EEPROM to better
identify firmware versions/images.
Tonghao Zhang cleans up a code comment that no longer applies since
InterruptThrottleRate has been removed from the driver.
Alex fixes SR-IOV and MACVLAN offload interaction, where the MACVLAN
offload was incorrectly configuring several filters with the wrong
pool value which resulted in MACLVAN interfaces not being able to
receive traffic that had to pass over the physical interface. Fixed
transmit hangs and dropped receive frames when the number of VFs
changed. Added support for RSS on MACVLAN pools for X550 devices.
Fixed up the MACVLAN limitations so we can now support 63 offloaded
devices. Cleaned up MACVLAN code that is no longer needed with the
recent changes and fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
r8169: improve runtime pm
On my system with two network ports I found that runtime PM didn't
suspend the unused port. Therefore I checked runtime pm in this driver
in somewhat more detail and this series improves runtime pm in general
and solves the mentioned issue.
Tested on a system with RTL8168evl (MAC version 34).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
So far rpm doesn't cover cases like unused ports which are never
brought up. If they are active at probe time they remain in this state.
Included in this patch:
- Let the idle notification check whether we can suspend and let it
schedule the suspend. This way we don't need to have calls to
pm_schedule_suspend in different places.
- At the end of rtl_open and rtl_init_one send an idle notification
to allow suspending if the link is down. If a cable is plugged in
aneg is finished before the suspend timer expires and the suspend
request is cancelled.
- Change rtl8169_runtime_suspend to power down the chip if the
interface is down.
Successfully tested on a RTL8168evl (mac version 34).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch partially reverts commit e4fbce740f "r8169: Fix runtime
power management" from 2010. At that time the suspend delay was 100ms
and therefore suspending happened during initial aneg. Currently
suspend delay is 5s, so suspend starts after aneg and the issue
doesn't exist any longer. On my system aneg takes almost 3s, to be on
the safe side let's increase the suspend delay to 10s.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 2a15cd2ff4 "r8169: runtime resume before
shutdown" from 2012. Few months after this change the underlying issue
was solved in the PCI core with commit 3ff2de9ba1 "PCI/PM: Resume
device before shutdown".
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Maloy says:
====================
tipc: improvements to group messaging
We make a number of simplifications and improvements to the group
messaging service. They aim at readability/maintainability of the code
as well as scalability.
The series is based on commit f9c935db80 ("tipc: fix problems with
multipoint-to-point flow control) which has been applied to 'net' but
not yet to 'net-next'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current criteria for returning POLLOUT from a group member socket is
too simplistic. It basically returns POLLOUT as soon as the group has
external destinations, something obviously leading to a lot of spinning
during destination congestion situations. At the same time, the internal
congestion handling is unnecessarily complex.
We now change this as follows.
- We introduce an 'open' flag in struct tipc_group. This flag is used
only to help poll() get the setting of POLLOUT right, and *not* for
congeston handling as such. This means that a user can choose to
ignore an EAGAIN for a destination and go on sending messages to
other destinations in the group if he wants to.
- The flag is set to false every time we return EAGAIN on a send call.
- The flag is set to true every time any member, i.e., not necessarily
the member that caused EAGAIN, is removed from the small_win list.
- We remove the group member 'usr_pending' flag. The size of the send
window and presence in the 'small_win' list is sufficient criteria
for recognizing congestion.
This solution seems to be a reasonable compromise between 'anycast',
which is normally not waiting for POLLOUT for a specific destination,
and the other three send modes, which are.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a member joins a group, it also indicates a binding scope. This
makes it possible to create both node local groups, invisible to other
nodes, as well as cluster global groups, visible everywhere.
In order to avoid that different members end up having permanently
differing views of group size and memberhip, we must inhibit locally
and globally bound members from joining the same group.
We do this by using the binding scope as an additional separator between
groups. I.e., a member must ignore all membership events from sockets
using a different scope than itself, and all lookups for message
destinations must require an exact match between the message's lookup
scope and the potential target's binding scope.
Apart from making it possible to create local groups using the same
identity on different nodes, a side effect of this is that it now also
becomes possible to create a cluster global group with the same identity
across the same nodes, without interfering with the local groups.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a user is subscribing for binding table publications,
he will receive a PUBLISH event for all already existing matching items
in the binding table.
However, a group socket making a subscriptions doesn't need this initial
status update from the binding table, because it has already scanned it
during the join operation. Worse, the multiplicatory effect of issuing
mutual events for dozens or hundreds group members within a short time
frame put a heavy load on the topology server, with the end result that
scale out operations on a big group tend to take much longer than needed.
We now add a new filter option, TIPC_SUB_NO_STATUS, for topology server
subscriptions, so that this initial avalanche of events is suppressed.
This change, along with the previous commit, significantly improves the
range and speed of group scale out operations.
We keep the new option internal for the tipc driver, at least for now.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a socket is joining a group, we look up in the binding table to
find if there are already other members of the group present. This is
used for being able to return EAGAIN instead of EHOSTUNREACH if the
user proceeds directly to a send attempt.
However, the information in the binding table can be used to directly
set the created member in state MBR_PUBLISHED and send a JOIN message
to the peer, instead of waiting for a topology PUBLISH event to do this.
When there are many members in a group, the propagation time for such
events can be significant, and we can save time during the join
operation if we use the initial lookup result fully.
In this commit, we eliminate the member state MBR_DISCOVERED which has
been the result of the initial lookup, and do instead go directly to
MBR_PUBLISHED, which initiates the setup.
After this change, the tipc_member FSM looks as follows:
+-----------+
---->| PUBLISHED |-----------------------------------------------+
PUB- +-----------+ LEAVE/WITHRAW |
LISH |JOIN |
| +-------------------------------------------+ |
| | LEAVE/WITHDRAW | |
| | +------------+ | |
| | +----------->| PENDING |---------+ | |
| | |msg/maxactv +-+---+------+ LEAVE/ | | |
| | | | | WITHDRAW | | |
| | | +----------+ | | | |
| | | |revert/maxactv| | | |
| | | V V V V V
| +----------+ msg +------------+ +-----------+
+-->| JOINED |------>| ACTIVE |------>| LEAVING |--->
| +----------+ +--- -+------+ LEAVE/+-----------+DOWN
| A A | WITHDRAW A A A EVT
| | | |RECLAIM | | |
| | |REMIT V | | |
| | |== adv +------------+ | | |
| | +---------| RECLAIMING |--------+ | |
| | +-----+------+ LEAVE/ | |
| | |REMIT WITHDRAW | |
| | |< adv | |
| |msg/ V LEAVE/ | |
| |adv==ADV_IDLE+------------+ WITHDRAW | |
| +-------------| REMITTED |------------+ |
| +------------+ |
|PUBLISH |
JOIN +-----------+ LEAVE/WITHDRAW |
---->| JOINING |-----------------------------------------------+
+-----------+
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the changes in the previous commit the group LEAVE sequence
can be simplified.
We now let the arrival of a LEAVE message unconditionally issue a group
DOWN event to the user. When a topology WITHDRAW event is received, the
member, if it still there, is set to state LEAVING, but we only issue a
group DOWN event when the link to the peer node is gone, so that no
LEAVE message is to be expected.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current implementation, a group socket receiving topology
events about other members just converts the topology event message
into a group event message and stores it until it reaches the right
state to issue it to the user. This complicates the code unnecessarily,
and becomes impractical when we in the coming commits will need to
create and issue membership events independently.
In this commit, we change this so that we just notice the type and
origin of the incoming topology event, and then drop the buffer. Only
when it is time to actually send a group event to the user do we
explicitly create a new message and send it upwards.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analysis reveals that the member state MBR_QURANTINED in reality is
unnecessary, and can be replaced by the state MBR_JOINING at all
occurrencs.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle a corner case in the function tipc_group_update_rcv_win().
During extreme pessure it might happen that a message receiver has all
its active senders in RECLAIMING or REMITTED mode, meaning that there
is nobody to reclaim advertisements from if an additional sender tries
to go active.
Currently we just set the new sender to ACTIVE anyway, hence at least
theoretically opening up for a receiver queue overflow by exceeding the
MAX_ACTIVE limit. The correct solution to this is to instead add the
member to the pending queue, while letting the oldest member in that
queue revert to JOINED state.
In this commit we refactor the code for handling message arrival from
a JOINED member, both to make it more comprehensible and to cover the
case described above.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- We remove the 'reclaiming' member list in struct tipc_group, since
it doesn't serve any purpose.
- We simplify the GRP_REMIT_MSG branch of tipc_group_protocol_rcv().
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
ethtool ringparam upper bound
This patchset by Jenny adds sanity checks in ethtool ringparam
operation for input upper bounds, similarly to what's done in
ethtool_set_channels.
The checks are added in patch 1, using a call to get_ringparam
prior to calling set_ringparam NDO.
Patch 2 changes the function's behavior in mlx4_en, so that
it returns an error for out-of-range input, instead of rounding
it to closest valid, similar to mlx5e.
Patch 3 removes the upper bound checks in mlx5e_ethtool_set_ringparam
as it becomes redundant.
Series generated against net-next commit:
f66faae2f8 Merge branch 'ipv6-ipv4-nexthop-align'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the checks are done in upper layer ethtool code,
checks in driver are not needed any more.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current implementation, any requested RX/TX ring size value
that is less than minimum is silently casted to nearest valid value.
Update this behavior to align with mlx5 behavior by printing warning
in dmesg and remaining the size unchanged.
Kernel is responsible for verifying against the maximum.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a sanity check to ensure that all requested ring parameters
are within bounds, which should reduce errors in driver implementation.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
