The NIC has a limited number of offloaded VXLAN UDP ports (usually 4).
Instead of letting the firmware fail when trying to add more ports than
it can handle, let the driver check it on its own.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The hardware offloads 4789 UDP port (default VXLAN port) automatically.
Add it to the software database as well in order to reflect the hardware
state appropriately.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In case a chain is empty and not explicitly created by a user,
such chain should not exist. The only exception is if there is
an action "goto chain" pointing to it. In that case, don't show the
chain in the dump. Track the chain references held by actions and
use them to find out if a chain should or should not be shown
in chain dump.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-07-27
1) Extend the output_mark to also support the input direction
and masking the mark values before applying to the skb.
2) Add a new lookup key for the upcomming xfrm interfaces.
3) Extend the xfrm lookups to match xfrm interface IDs.
4) Add virtual xfrm interfaces. The purpose of these interfaces
is to overcome the design limitations that the existing
VTI devices have.
The main limitations that we see with the current VTI are the
following:
VTI interfaces are L3 tunnels with configurable endpoints.
For xfrm, the tunnel endpoint are already determined by the SA.
So the VTI tunnel endpoints must be either the same as on the
SA or wildcards. In case VTI tunnel endpoints are same as on
the SA, we get a one to one correlation between the SA and
the tunnel. So each SA needs its own tunnel interface.
On the other hand, we can have only one VTI tunnel with
wildcard src/dst tunnel endpoints in the system because the
lookup is based on the tunnel endpoints. The existing tunnel
lookup won't work with multiple tunnels with wildcard
tunnel endpoints. Some usecases require more than on
VTI tunnel of this type, for example if somebody has multiple
namespaces and every namespace requires such a VTI.
VTI needs separate interfaces for IPv4 and IPv6 tunnels.
So when routing to a VTI, we have to know to which address
family this traffic class is going to be encapsulated.
This is a lmitation because it makes routing more complex
and it is not always possible to know what happens behind the
VTI, e.g. when the VTI is move to some namespace.
VTI works just with tunnel mode SAs. We need generic interfaces
that ensures transfomation, regardless of the xfrm mode and
the encapsulated address family.
VTI is configured with a combination GRE keys and xfrm marks.
With this we have to deal with some extra cases in the generic
tunnel lookup because the GRE keys on the VTI are actually
not GRE keys, the GRE keys were just reused for something else.
All extensions to the VTI interfaces would require to add
even more complexity to the generic tunnel lookup.
So to overcome this, we developed xfrm interfaces with the
following design goal:
It should be possible to tunnel IPv4 and IPv6 through the same
interface.
No limitation on xfrm mode (tunnel, transport and beet).
Should be a generic virtual interface that ensures IPsec
transformation, no need to know what happens behind the
interface.
Interfaces should be configured with a new key that must match a
new policy/SA lookup key.
The lookup logic should stay in the xfrm codebase, no need to
change or extend generic routing and tunnel lookups.
Should be possible to use IPsec hardware offloads of the underlying
interface.
5) Remove xfrm pcpu policy cache. This was added after the flowcache
removal, but it turned out to make things even worse.
From Florian Westphal.
6) Allow to update the set mark on SA updates.
From Nathan Harold.
7) Convert some timestamps to time64_t.
From Arnd Bergmann.
8) Don't check the offload_handle in xfrm code,
it is an opaque data cookie for the driver.
From Shannon Nelson.
9) Remove xfrmi interface ID from flowi. After this pach
no generic code is touched anymore to do xfrm interface
lookups. From Benedict Wong.
10) Allow to update the xfrm interface ID on SA updates.
From Nathan Harold.
11) Don't pass zero to ERR_PTR() in xfrm_resolve_and_create_bundle.
From YueHaibing.
12) Return more detailed errors on xfrm interface creation.
From Benedict Wong.
13) Use PTR_ERR_OR_ZERO instead of IS_ERR + PTR_ERR.
From the kbuild test robot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
net/xfrm/xfrm_interface.c:692:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes: 44e2b838c2 ("xfrm: Return detailed errors from xfrmi_newlink")
CC: Benedict Wong <benedictwong@google.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This series from Tariq adds the support for device-out XDP redirect.
Start with a simple RX and XDP cleanups:
- Replace call to MPWQE free with dealloc in interface down flow
- Do not recycle RX pages in interface down flow
- Gather all XDP pre-requisite checks in a single function
- Restrict the combination of large MTU and XDP
Since now XDP logic is going to be called from TX side as well,
generic XDP TX logic is not RX only anymore, for that Tariq creates
a new xdp.c file and moves XDP related code into it, and generalizes
the code to support XDP TX for XDP redirect, such as the xdp tx sq
structures and xdp counters.
XDP redirect support:
Add implementation for the ndo_xdp_xmit callback.
Dedicate a new set of XDP-SQ instances to satisfy the XDP_REDIRECT
requests. These instances are totally separated from the existing
XDP-SQ objects that satisfy local XDP_TX actions.
Performance tests:
xdp_redirect_map from ConnectX-5 to ConnectX-5.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet-rate of 64B packets.
Single queue: 7 Mpps.
Multi queue: 55 Mpps.
-Saeed.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbWk7YAAoJEEg/ir3gV/o+b+4H/RKfHrDgqRcz+qw2hYqMc/0Q
N/s6SaZm/AZi63lOwUeeSGORJSGYxxbwcWFNuI6CZrHEupi0zQivDko+E3fTPeDQ
3Y7jAaLjB0ZsWwEukcgZ1PG1QIYUg2/EBijG+aah9q/TuUfsFYJDRImlXRi5zvSe
34yuLls6ctuoxoet5S5SVWFssdQZ2YpmmMNqVmQIRGDSmd03dhE1WUGUGmPhR5mK
vxUBL5X3ucb1lcqxpFnZqsrIZphxkimX0q8qUK1yHk7VU4JXZgikPkRFM1mnlNt0
YosvDlnDqJugBvYspBUx+9au8wxgPwpHEbnGKdS/npsIuNXa0ZFnEky1tp6CzV0=
=3CNK
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-07-26 (XDP redirect)
This series from Tariq adds the support for device-out XDP redirect.
Start with a simple RX and XDP cleanups:
- Replace call to MPWQE free with dealloc in interface down flow
- Do not recycle RX pages in interface down flow
- Gather all XDP pre-requisite checks in a single function
- Restrict the combination of large MTU and XDP
Since now XDP logic is going to be called from TX side as well,
generic XDP TX logic is not RX only anymore, for that Tariq creates
a new xdp.c file and moves XDP related code into it, and generalizes
the code to support XDP TX for XDP redirect, such as the xdp tx sq
structures and xdp counters.
XDP redirect support:
Add implementation for the ndo_xdp_xmit callback.
Dedicate a new set of XDP-SQ instances to satisfy the XDP_REDIRECT
requests. These instances are totally separated from the existing
XDP-SQ objects that satisfy local XDP_TX actions.
Performance tests:
xdp_redirect_map from ConnectX-5 to ConnectX-5.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet-rate of 64B packets.
Single queue: 7 Mpps.
Multi queue: 55 Mpps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The root directories of netdevsim should only be used by the core
to create per-device subdirectories, so limit their visibility to
the core file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tobin C. Harding says:
====================
docs: net: Convert netdev-FAQ to RST
Jon answered all the tree questions on v1 so if you will please take
this through your tree that would be awesome.
v2:
- Fix typo 'canonical_path_format' (thanks Edward)
- Add patch fixing references netdev-FAQ
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
File 'Documentation/networking/netdev-FAQ.txt' has been converted to RST
format. We should update all links/references to point to the new file.
Update references to netdev-FAQ
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preferred kernel docs format is now restructured text. Convert
netdev-FAQ.txt to restructured text.
- Add SPDX license identifier.
- Change file heading 'Information you need to know about netdev' to
'netdev FAQ' to better suit displayed index (in HTML).
- Change question/answer layout to suit rst. Copy format in
Documentation/bpf/bpf_devel_QA.rst
- Fix indentation of code snippets
- If multiple consecutive URLs appear put them in a list (to maintain
whitespace).
- Use uniform spelling of 'bug fix' throughout document (not bugfix or
bug-fix).
- Add double back ticks to 'net' and 'net-next' when referring to the
trees.
- Use rst references for Documentation/ links.
- Add rst label 'netdev-FAQ' for referencing by other docs files.
- Remove stale entry from Documentation/networking/00-INDEX
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to convert Documentation/network/netdev-FAQ.rst to
restructured text format. We would like to be able to reference 'the
canonical patch format' section.
Add rest label: 'the_canonical_patch_format'.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
starfire_init_one() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hisax_cs_new() and hisax_cs_setup() are never called in atomic context.
They call kmalloc() and kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
init_PStack() is never called in atomic context.
It calls kmalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nj_probe() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hfc_probe() is never called in atomic context.
It calls kzalloc() with GFP_ATOMIC, which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hns_dsaf_roce_reset is exported and used in hns_roce_hw_v1.c
In commit 336a443bd9 ("net: hns: Make many functions static") I make
it static wrongly.
drivers/infiniband/hw/hns/hns_roce_hw_v1.o: In function `hns_roce_v1_reset':
hns_roce_hw_v1.c:(.text+0x37ac): undefined reference to `hns_dsaf_roce_reset'
hns_roce_hw_v1.c:(.text+0x37cc): undefined reference to `hns_dsaf_roce_reset'
Fixes: 336a443bd9 ("net: hns: Make many functions static")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use designated function mlx5e_dma_get() to get
the mlx5e_sq_dma object to be pushed into fifo.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pointers in DB are static, move them to read-only area so they
do not share a cacheline with fields modified in datapath.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A loaded XDP program might write to the xdp_frame data area,
prefetchw() it to avoid a potential cache miss.
Performance tests:
ConnectX-5, XDP_TX packet rate, single ring.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Before: 13,172,976 pps
After: 13,456,248 pps
2% gain.
Fixes: 22f4539881 ("net/mlx5e: Support XDP over Striding RQ")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add implementation for the ndo_xdp_xmit callback.
Dedicate a new set of XDP-SQ instances to satisfy the XDP_REDIRECT
requests. These instances are totally separated from the existing
XDP-SQ objects that satisfy local XDP_TX actions.
Performance tests:
xdp_redirect_map from ConnectX-5 to ConnectX-5.
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet-rate of 64B packets.
Single queue: 7 Mpps.
Multi queue: 55 Mpps.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the downstream patch that adds support to XDP_REDIRECT-out,
the XDP xmit frame function doesn't share the same run context as
the NAPI that polls the XDP-SQ completion queue.
Hence, need to re-order the XDP-SQ fields to avoid cacheline
false-sharing.
Take redirect_flush and doorbell out of DB, into separated
cachelines.
Add a cacheline breaker within the stats struct.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Separate the XDP counters into two sets:
(1) One set reside in the RQ stats, and they monitor XDP stats
in the RQ side.
(2) Another set is per XDP-SQ, and they monitor XDP stats that
are related to XDP transmit flow.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Convert the XDP xmit functions to use the generic xdp_frame API
in XDP_TX flow.
Same functions will be used later in this series to transmit
the XDP redirect-out packets as well.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add per-ring and total stats for received packets that
goes into XDP redirection.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Take XDP code out of the general EN header and RX file into
new XDP files.
Currently, XDP-SQ resides only within an RQ and used from a
single flow (XDP_TX) triggered upon RX completions.
In a downstream patch, additional type of XDP-SQ instances will be
presented and used for the XDP_REDIRECT flow, totally unrelated to
the RX context.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add checks in control path upon an MTU change or an XDP program set,
to prevent reaching cases where large MTU and XDP are set simultaneously.
This is to make sure we allow XDP only with the linear RX memory scheme,
i.e. a received packet is not scattered to different pages.
Change mlx5e_rx_get_linear_frag_sz() accordingly, so that we make sure
the XDP configuration can really be set, instead of assuming that it is.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Dedicate a function to all checks done when setting an XDP program.
Take indications from priv instead of netdev features.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
No need to expose the MPWQE free function to control path.
The dealloc function already exposed, use it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-07-26
This series contains updates to ixgbe and igb.
Tony fixes ixgbe to add checks to ensure jumbo frames or LRO get enabled
after an XDP program is loaded.
Shannon Nelson adds the missing security configuration registers to the
ixgbe register dump, which will help in debugging.
Christian Grönke fixes an issue in igb that occurs on SGMII based SPF
mdoules, by reverting changes from 2 previous patches. The issue was
that initialization would fail on the fore mentioned modules because the
driver would try to reset the PHY before obtaining the PHY address of
the SGMII attached PHY.
Venkatesh Srinivas replaces wmb() with dma_wmb() for doorbell writes,
which avoids SFENCEs before the doorbell writes.
Alex cleans up and refactors ixgbe Tx/Rx shutdown to reduce time needed
to stop the device. The code refactor allows us to take the completion
time into account when disabling queues, so that on some platforms with
higher completion times, would not result in receive queues disabled
messages.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Once user manually deletes the chain using "chain del", the chain cannot
be marked as explicitly created anymore.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: David S. Miller <davem@davemloft.net>
The zerocopy path ultimately calls iov_iter_get_pages, which defines the
step function for ITER_KVECs as simply, return -EFAULT. Taking the
non-zerocopy path for ITER_KVECs avoids the unnecessary fallback.
See https://lore.kernel.org/lkml/20150401023311.GL29656@ZenIV.linux.org.uk/T/#u
for a discussion of why zerocopy for vmalloc data is not a good idea.
Discovered while testing NBD traffic encrypted with ktls.
Fixes: c46234ebb4 ("tls: RX path for ktls")
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code at line 1850 is unreachable. Fix this by removing the break
statement above it, so the code for case RTM_GETCHAIN can be
properly executed.
Addresses-Coverity-ID: 1472050 ("Structurally dead code")
Fixes: 32a4f5ecd7 ("net: sched: introduce chain object to uapi")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tunnel reception hook is only used by l2tp_ppp for skipping PPP
framing bytes. This is a session specific operation, but once a PPP
session sets ->recv_payload_hook on its tunnel, all frames received by
the tunnel will enter pppol2tp_recv_payload_hook(), including those
targeted at Ethernet sessions (an L2TPv3 tunnel can multiplex PPP and
Ethernet sessions).
So this mechanism is wrong, and uselessly complex. Let's just move this
functionality to the pppol2tp rx handler and drop ->recv_payload_hook.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
when tipc_own_id failed to obtain node identity,dev_put should
be call before return -EINVAL.
Fixes: 682cd3cf94 ("tipc: confgiure and apply UDP bearer MTU on running links")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed checks against non-NULL before calling kfree_skb() and
crypto_free_aead(). These functions are safe to be called with NULL
as an argument.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to install a child qdisc under cbs. The main use case
is to install ETF (Earliest TxTime First) qdisc under cbs, so there's
another level of control for time-sensitive traffic.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:73:20: warning: symbol 'hns_ae_get_handle' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:332:6: warning: symbol 'hns_ae_stop' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:360:6: warning: symbol 'hns_ae_toggle_ring_irq' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:580:6: warning: symbol 'hns_ae_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:663:6: warning: symbol 'hns_ae_get_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:695:6: warning: symbol 'hns_ae_get_strings' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:728:5: warning: symbol 'hns_ae_get_sset_count' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:774:6: warning: symbol 'hns_ae_update_led_status' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:786:5: warning: symbol 'hns_ae_cpld_set_led_id' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:798:6: warning: symbol 'hns_ae_get_regs' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ae_adapt.c:823:5: warning: symbol 'hns_ae_get_regs_len' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c:342:6: warning: symbol 'hns_gmac_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:934:12: warning: symbol 'hns_mac_get_vaddr' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_mac.c:953:5: warning: symbol 'hns_mac_get_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:343:6: warning: symbol 'hns_dsaf_srst_chns' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:366:1: warning: symbol 'hns_dsaf_srst_chns_acpi' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:373:6: warning: symbol 'hns_dsaf_roce_srst' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:387:6: warning: symbol 'hns_dsaf_roce_srst_acpi' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:571:5: warning: symbol 'hns_mac_get_sfp_prsnt' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_misc.c:589:5: warning: symbol 'hns_mac_get_sfp_prsnt_acpi' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:31:12: warning: symbol 'g_dsaf_mode_match' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:45:5: warning: symbol 'hns_dsaf_get_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:962:6: warning: symbol 'hns_dsaf_tcam_addr_get' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2087:6: warning: symbol 'hns_dsaf_port_work_rate_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:2837:5: warning: symbol 'hns_dsaf_roce_reset' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:76:5: warning: symbol 'hns_ppe_common_get_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:107:6: warning: symbol 'hns_ppe_common_free_cfg' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_ppe.c:340:6: warning: symbol 'hns_ppe_uninit_ex' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c:708:5: warning: symbol 'hns_rcb_get_ring_num' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_rcb.c:744:14: warning: symbol 'hns_rcb_common_get_vaddr' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:314:6: warning: symbol 'hns_xgmac_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1303:6: warning: symbol 'hns_nic_update_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1585:6: warning: symbol 'hns_nic_poll_controller' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1938:6: warning: symbol 'hns_set_multicast_list' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1960:6: warning: symbol 'hns_nic_set_rx_mode' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:661:6: warning: symbol 'hns_get_ringparam' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:811:6: warning: symbol 'hns_get_channels' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:828:6: warning: symbol 'hns_get_ethtool_stats' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:886:6: warning: symbol 'hns_get_strings' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:976:5: warning: symbol 'hns_get_sset_count' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:1010:5: warning: symbol 'hns_phy_led_set' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:1032:5: warning: symbol 'hns_set_phys_id' was not declared. Should it be static?
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:1106:6: warning: symbol 'hns_get_regs' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the tls binary to .gitignore
Fixes: 7f657d5bf5 ("selftests: tls: add selftests for TLS sockets")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to allow us to take completion time into account when
disabling queues. Previously we were just working with hard coded values
for how long we should wait. This worked fine for the standard case where
completion timeout was operating in the 50us to 50ms range, however on
platforms that have higher completion timeout times this was resulting in
Rx queues disable messages being displayed as we weren't waiting long
enough for outstanding Rx DMA completions.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to help reduce the time needed to shutdown the
transmit and receive paths for the device. Specifically what we now do
after this patch is disable the transmit path first at the netdev level,
and then work on disabling the Rx. This way while we are waiting on the Rx
queues to be disabled the Tx queues have an opportunity to drain out.
In addition I have dropped the 10ms timeout that was left in the ixgbe_down
function that seems to have been carried through from back in e1000 as far
as I can tell. We shouldn't need it since we don't actually disable the Tx
until much later and we have additional logic in place for verifying the Tx
queues have been disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
igb writes to doorbells to post transmit and receive descriptors;
after writing descriptors to memory but before writing to doorbells,
use dma_wmb() rather than wmb(). wmb() is more heavyweight than
necessary before doorbell writes.
On x86, this avoids SFENCEs before doorbell writes in both the
tx and rx refill paths.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reverts two previous applied patches to fix an issue
that appeared when using SGMII based SFP modules. In the current
state the driver will try to reset the PHY before obtaining the
phy_addr of the SGMII attached PHY. That leads to an error in
e1000_write_phy_reg_sgmii_82575. Causing the initialization to
fail:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of ????:??:??.? failed with error -3
The patches being reverted are:
commit 1827853354
Author: Aaron Sierra <asierra@xes-inc.com>
Date: Tue Nov 29 10:03:56 2016 -0600
igb: reset the PHY before reading the PHY ID
commit 440aeca4b9
Author: Matwey V Kornilov <matwey@sai.msu.ru>
Date: Thu Nov 24 13:32:48 2016 +0300
igb: Explicitly select page 0 at initialization
The first reverted patch directly causes the problem mentioned above.
In case of SGMII the phy_addr is not known at this point and will
only be obtained by 'igb_get_phy_id_82575' further down in the code.
The second removed patch selects forces selection of page 0 in the
PHY. Something that the reset tries to address as well.
As pointed out by Alexander Duzck, the patch below fixes the same
issue but in the proper location:
commit 4e684f59d7
Author: Chris J Arges <christopherarges@gmail.com>
Date: Wed Nov 2 09:13:42 2016 -0500
igb: Workaround for igb i210 firmware issue
Reverts: 440aeca4b9.
Reverts: 1827853354.
Signed-off-by: Christian Grönke <c.groenke@infodas.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ixgbe's security configuration registers into
the register dump.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
XDP does not support jumbo frames or LRO. These checks are being made
outside the driver when an XDP program is loaded, however, there is
nothing preventing these from changing after an XDP program is loaded.
Add the checks so that while an XDP program is loaded, do not allow MTU
to be changed or LRO to be enabled.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, code at label *out* is unreachable. Fix this by updating
variable *ret* with -EINVAL, so the jump to *out* can be properly
executed instead of directly returning from function.
Addresses-Coverity-ID: 1472059 ("Structurally dead code")
Fixes: 1e2b44e78e ("rds: Enable RDS IPv6 support")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build error, implicit declaration of function __inet6_ehashfn shows up
When RDS is enabled but not IPV6.
net/rds/connection.c: In function ‘rds_conn_bucket’:
net/rds/connection.c:67:9: error: implicit declaration of function ‘__inet6_ehashfn’; did you mean ‘__inet_ehashfn’? [-Werror=implicit-function-declaration]
hash = __inet6_ehashfn(lhash, 0, fhash, 0, rds_hash_secret);
^~~~~~~~~~~~~~~
__inet_ehashfn
Current code adds IPV6 as a depends on in config RDS.
Fixes: eee2fa6ab3 ("rds: Changing IP address internal representation to struct in6_addr")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: patches 2018-07-25
here are 4 more patches for SMC: The first one is just a small
code cleanup in preparation for patch 2. Patch 2 switches to the
use of the vlan-gid for VLAN traffic. Patch 3 improves diagnosis
when creating SMC connections. Patch 4 improves synchronization
between local and remote link groups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
