Fix a crash during boot reported by Jeff Moyer. Fix the issue of accessing
cfqq after freeing it.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@carl.(none)>
After the merge of the IO controller patches, booting on my megaraid
box ran much slower. Vivek Goyal traced it down to megaraid discovery
creating tons of devices, each suffering a grace period when they later
kill that queue (if no device is found).
So lets use call_rcu() to batch these deferred frees, instead of taking
the grace period hit for each one.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o One of the goals of block IO controller is that it should be able to
support mulitple io control policies, some of which be operational at
higher level in storage hierarchy.
o To begin with, we had one io controlling policy implemented by CFQ, and
I hard coded the CFQ functions called by blkio. This created issues when
CFQ is compiled as module.
o This patch implements a basic dynamic io controlling policy registration
functionality in blkio. This is similar to elevator functionality where
ioschedulers register the functions dynamically.
o Now in future, when more IO controlling policies are implemented, these
can dynakically register with block IO controller.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o blkio controller is inside the kernel and cfq makes use of interfaces
exported by blkio. CFQ can be a module too, hence export symbols used
by CFQ.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cfq_arm_slice_timer() has logic to disable idle window for SSD device. The same
thing should be done at cfq_select_queue() too, otherwise we will still see
idle window. This makes the nonrot check logic consistent in cfq.
Tests in a intel SSD with low_latency knob close, below patch can triple disk
thoughput for muti-thread sequential read.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o rq_noidle() is supposed to tell cfq that do not expect a request after this
one, hence don't idle. But this does not seem to work very well. For example
for direct random readers, rq_noidle = 1 but there is next request coming
after this. Not idling, leads to a group not getting its share even if
group_isolation=1.
o The right solution for this issue is to scan the higher layers and set
right flag (WRITE_SYNC or WRITE_ODIRECT). For the time being, this single
line fix helps. This should not have any significant impact when we are
not using cgroups. I will later figure out IO paths in higher layer and
fix it.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o If a group is running only a random reader, then it will not have enough
traffic to keep disk busy and we will reduce overall throughput. This
should result in better latencies for random reader though. If we don't
idle on random reader service tree, then this random reader will experience
large latencies if there are other groups present in system with sequential
readers running in these.
o One solution suggested by corrado is that by default keep the random readers
or sync-noidle workload in root group so that during one dispatch round
we idle only once on sync-noidle tree. This means that all the sync-idle
workload queues will be in their respective group and we will see service
differentiation in those but not on sync-noidle workload.
o Provide a tunable group_isolation. If set, this will make sure that even
sync-noidle queues go in their respective group and we wait on these. This
provides stronger isolation between groups but at the expense of throughput
if group does not have enough traffic to keep the disk busy.
o By default group_isolation = 0
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Async queues are not per group. Instead these are system wide and maintained
in root group. Hence their workload slice length should be calculated
based on total number of queues in the system and not just queues in the
root group.
o As root group's default weight is 1000, make sure to charge async queue
more in terms of vtime so that it does not get more time on disk because
root group has higher weight.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o If a queue consumes its slice and then gets deleted from service tree, its
associated group will also get deleted from service tree if this was the
only queue in the group. That will make group loose its share.
o For the queues on which we have idling on and if these have used their
slice, wait a bit for these queues to get backlogged again and then
expire these queues so that group does not loose its share.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o If a task changes cgroup, drop reference to the cfqq associated with io
context and set cfqq pointer stored in ioc to NULL so that upon next request
arrival we will allocate a new queue in new group.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Do not allow following three operations across groups for isolation.
- selection of co-operating queues
- preemtpions across groups
- request merging across groups.
o Async queues are currently global and not per group. Allow preemption of
an async queue if a sync queue in other group gets backlogged.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Export disk time and sector used by a group to user space through cgroup
interface.
o Also export a "dequeue" interface to cgroup which keeps track of how many
a times a group was deleted from service tree. Helps in debugging.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o One can choose to change elevator or delete a cgroup. Implement group
reference counting so that both elevator exit and cgroup deletion can
take place gracefully.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Nauman Rafique <nauman@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Determine the cgroup IO submitting task belongs to and create the cfq
group if it does not exist already.
o Also link cfqq and associated cfq group.
o Currently all async IO is mapped to root group.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o This patch introduces the functionality to do the accounting of group time
when a queue expires. This time used decides which is the group to go
next.
o Also introduce the functionlity to save and restore the workload type
context with-in group. It might happen that once we expire the cfq queue
and group, a different group will schedule in and we will lose the context
of the workload type. Hence save and restore it upon queue expiry.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o So far we had 300ms soft target latency system wide. Now with the
introduction of cfq groups, divide that latency by number of groups so
that one can come up with group target latency which will be helpful
in determining the workload slice with-in group and also the dynamic
slice length of the cfq queue.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Bring in the per cfq group weight and how vdisktime is calculated for the
group. Also bring in the functionality of updating the min_vdisktime of
the group service tree.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o So far we just had one cfq_group in cfq_data. To create space for more than
one cfq_group, we need to have a service tree of groups where all the groups
can be queued if they have active cfq queues backlogged in these.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Currently cfqq deletes a queue from service tree if it is empty (even if
we might idle on the queue). This patch keeps the queue on service tree
hence associated group remains on the service tree until we decide that
we are not going to idle on the queue and expire it.
o This just helps in time accounting for queue/group and in implementation
of rest of the patches.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o Implement a macro to traverse each service tree in the group. This avoids
usage of double for loop and special condition for idle tree 4 times.
o Macro is little twisted because of special handling of idle class service
tree.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o This patch introduce the notion of cfq groups. Soon we will can have multiple
groups of different weights in the system.
o Various service trees (prioclass and workload type trees), will become per
cfq group. So hierarchy looks as follows.
cfq_groups
|
workload type
|
cfq queue
o When an scheduling decision has to be taken, first we select the cfq group
then workload with-in the group and then cfq queue with-in the workload
type.
o This patch just makes various workload service tree per cfq group and
introduce the function to be able to choose a group for scheduling.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
o must_dispatch flag should be set only if we decided not to run the queue
and dispatch the request.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Since commit 2f5cb7381b, each queue can send
up to 4 * 4 requests if only one queue exists. I wonder why we have such limit.
Device supports tag can send more requests. For example, AHCI can send 31
requests. Test (direct aio randread) shows the limits reduce about 4% disk
thoughput.
On the other hand, since we send one request one time, if other queue
pop when current is sending more than cfq_quantum requests, current queue will
stop send requests soon after one request, so sounds there is no big latency.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This reverts commit 3586e917f2.
Corrado Zoccolo <czoccolo@gmail.com> correctly points out, that we need
consistency of rb_key offset across groups. This means we cannot properly
use the per-service_tree service count. Revert this change.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Idling logic was disabled in some corner cases, leading to unfair share
for noidle queues.
* the idle timer was not armed if there were other requests in the
driver. unfortunately, those requests could come from other workloads,
or queues for which we don't enable idling. So we will check only
pending requests from the active queue
* rq_noidle check on no-idle queue could disable the end of tree idle if
the last completed request was rq_noidle. Now, we will disable that
idle only if all the queues served in the no-idle tree had rq_noidle
requests.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Seeky sync queues with large depth can gain unfairly big share of disk
time, at the expense of other seeky queues. This patch ensures that
idling will be enabled for queues with I/O depth at least 4, and small
think time. The decision to enable idling is sticky, until an idle
window times out without seeing a new request.
The reasoning behind the decision is that, if an application is using
large I/O depth, it is already optimized to make full utilization of
the hardware, and therefore we reserve a slice of exclusive use for it.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
An incoming no-idle queue should preempt the active no-idle queue
only if the active queue is idling due to service tree empty.
Previous code was buggy in two ways:
* it relied on service_tree field to be set on the active queue, while
it is not set when the code is idling for a new request
* it didn't check for the service tree empty condition, so could lead to
LIFO behaviour if multiple queues with depth > 1 were preempting each
other on an non-NCQ device.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
CFQ's detection of queueing devices initially assumes a queuing device
and detects if the queue depth reaches a certain threshold.
However, it will reconsider this choice periodically.
Unfortunately, if device is considered not queuing, CFQ will force a
unit queue depth for some workloads, thus defeating the detection logic.
This leads to poor performance on queuing hardware,
since the idle window remains enabled.
Given this premise, switching to hw_tag = 0 after we have proved at
least once that the device is NCQ capable is not a good choice.
The new detection code starts in an indeterminate state, in which CFQ behaves
as if hw_tag = 1, and then, if for a long observation period we never saw
large depth, we switch to hw_tag = 0, otherwise we stick to hw_tag = 1,
without reconsidering it again.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cfq_should_idle returns false for no-idle queues that are not the last,
so the control flow will never reach the removed code in a state that
satisfies the if condition.
The unreachable code was added to emulate previous cfq behaviour for
non-NCQ rotational devices. My tests show that even without it, the
performances and fairness are comparable with previous cfq, thanks to
the fact that all seeky queues are grouped together, and that we idle at
the end of the tree.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
For the moment, different workload cfq queues are put into different
service trees. But CFQ still uses "busy_queues" to estimate rb_key
offset when inserting a cfq queue into a service tree. I think this
isn't appropriate, and it should make use of service tree count to do
this estimation. This patch is for for-2.6.33 branch.
Signed-off-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Use HZ-independent calculation of milliseconds.
Add jiffies.h where it was missing since functions or macros
from it are used.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cfq has a bug in computation of next_rq, that affects transition
between multiple sequential request streams in a single queue
(e.g.: two sequential buffered writers of the same priority),
causing the alternation between the two streams for a transient period.
8,0 1 18737 0.260400660 5312 D W 141653311 + 256
8,0 1 20839 0.273239461 5400 D W 141653567 + 256
8,0 1 20841 0.276343885 5394 D W 142803919 + 256
8,0 1 20843 0.279490878 5394 D W 141668927 + 256
8,0 1 20845 0.292459993 5400 D W 142804175 + 256
8,0 1 20847 0.295537247 5400 D W 141668671 + 256
8,0 1 20849 0.298656337 5400 D W 142804431 + 256
8,0 1 20851 0.311481148 5394 D W 141668415 + 256
8,0 1 20853 0.314421305 5394 D W 142804687 + 256
8,0 1 20855 0.318960112 5400 D W 142804943 + 256
The fix makes sure that the next_rq is computed from the last
dispatched request, and not affected by merging.
8,0 1 37776 4.305161306 0 D W 141738087 + 256
8,0 1 37778 4.308298091 0 D W 141738343 + 256
8,0 1 37780 4.312885190 0 D W 141738599 + 256
8,0 1 37782 4.315933291 0 D W 141738855 + 256
8,0 1 37784 4.319064459 0 D W 141739111 + 256
8,0 1 37786 4.331918431 5672 D W 142803007 + 256
8,0 1 37788 4.334930332 5672 D W 142803263 + 256
8,0 1 37790 4.337902723 5672 D W 142803519 + 256
8,0 1 37792 4.342359774 5672 D W 142803775 + 256
8,0 1 37794 4.345318286 0 D W 142804031 + 256
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We need to rework this logic post the cooperating cfq_queue merging,
for now just get rid of it and Jeff Moyer will fix the fall out.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
CFQ has an optimization for cooperated applications. if several
io-context have close requests, they will get boost. But the
optimization get abused. Considering thread a, b, which work on one
file. a reads sectors s, s+2, s+4, ...; b reads sectors s+1, s+3, s
+5, ... Both a and b are sequential read, so they can open idle window.
a reads a sector s and goes to idle window and wakeup b. b reads sector
s+1, since in current implementation, cfq_should_preempt() thinks a and
b are cooperators, b will preempt a. b then reads sector s+1 and goes to
idle window and wakeup a. for the same reason, a will preempt b and
reads s+2. a and b will continue the circle. The circle will be very
long, and a and b will occupy whole disk queue. Other applications will
nearly have no chance to run.
Fix this limiting coop preempt until a queue is scheduled normally
again.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Commit a6151c3a5c inadvertently reversed
a preempt condition check, potentially causing a performance regression.
Make the meta check correct again.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Currently no-idle queues in cfq are not serviced fairly:
even if they can only dispatch a small number of requests at a time,
they have to compete with idling queues to be serviced, experiencing
large latencies.
We should notice, instead, that no-idle queues are the ones that would
benefit most from having low latency, in fact they are any of:
* processes with large think times (e.g. interactive ones like file
managers)
* seeky (e.g. programs faulting in their code at startup)
* or marked as no-idle from upper levels, to improve latencies of those
requests.
This patch improves the fairness and latency for those queues, by:
* separating sync idle, sync no-idle and async queues in separate
service_trees, for each priority
* service all no-idle queues together
* and idling when the last no-idle queue has been serviced, to
anticipate for more no-idle work
* the timeslices allotted for idle and no-idle service_trees are
computed proportionally to the number of processes in each set.
Servicing all no-idle queues together should have a performance boost
for NCQ-capable drives, without compromising fairness.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cfq can disable idling for queues in various circumstances.
When workloads of different priorities are competing, if the higher
priority queue has idling disabled, lower priority queues may steal
its disk share. For example, in a scenario with an RT process
performing seeky reads vs a BE process performing sequential reads,
on an NCQ enabled hardware, with low_latency unset,
the RT process will dispatch only the few pending requests every full
slice of service for the BE process.
The patch solves this issue by always performing idle on the last
queue at a given priority class > idle. If the same process, or one
that can pre-empt it (so at the same priority or higher), submits a
new request within the idle window, the lower priority queue won't
dispatch, saving the disk bandwidth for higher priority ones.
Note: this doesn't touch the non_rotational + NCQ case (no hardware
to test if this is a benefit in that case).
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We use different service trees for different priority classes.
This allows a simplification in the service tree insertion code, that no
longer has to consider priority while walking the tree.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We embed a pointer to the service tree in each queue, to handle multiple
service trees easily.
Service trees are enriched with a counter.
cfq_add_rq_rb is invoked after putting the rq in the fifo, to ensure
that all fields in rq are properly initialized.
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When the number of processes performing I/O concurrently increases,
a fixed time slice per process will cause large latencies.
This patch, if low_latency mode is enabled, will scale the time slice
assigned to each process according to a 300ms target latency.
In order to keep fairness among processes:
* The number of active processes is computed using a special form of
running average, that quickly follows sudden increases (to keep latency low),
and decrease slowly (to have fairness in spite of rapid decreases of this
value).
To safeguard sequential bandwidth, we impose a minimum time slice
(computed using 2*cfq_slice_idle as base, adjusted according to priority
and async-ness).
Signed-off-by: Corrado Zoccolo <czoccolo@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If active queue hasn't enough requests and idle window opens, cfq will not
dispatch sufficient requests to hardware. In such situation, current code
will zero hw_tag. But this is because cfq doesn't dispatch enough requests
instead of hardware queue doesn't work. Don't zero hw_tag in such case.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cfq_queues are merged if they are issuing requests within the mean seek
distance of one another. This patch detects when the coopearting stops and
breaks the queues back up.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
