These values are used with IS_ERR(), so it's more intuitive to define
them like a standard PTR_ERR() of a negative errno.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/146835e8-c086-4e85-7ece-bcba6795e6db@gmail.com
Quite some time ago the interrupt entry stubs for unused vectors in the
system vector range got removed and directly mapped to the spurious
interrupt vector entry point.
Sounds reasonable, but it's subtly broken. The spurious interrupt vector
entry point pushes vector number 0xFF on the stack which makes the whole
logic in __smp_spurious_interrupt() pointless.
As a consequence any spurious interrupt which comes from a vector != 0xFF
is treated as a real spurious interrupt (vector 0xFF) and not
acknowledged. That subsequently stalls all interrupt vectors of equal and
lower priority, which brings the system to a grinding halt.
This can happen because even on 64-bit the system vector space is not
guaranteed to be fully populated. A full compile time handling of the
unused vectors is not possible because quite some of them are conditonally
populated at runtime.
Bring the entry stubs back, which wastes 160 bytes if all stubs are unused,
but gains the proper handling back. There is no point to selectively spare
some of the stubs which are known at compile time as the required code in
the IDT management would be way larger and convoluted.
Do not route the spurious entries through common_interrupt and do_IRQ() as
the original code did. Route it to smp_spurious_interrupt() which evaluates
the vector number and acts accordingly now that the real vector numbers are
handed in.
Fixup the pr_warn so the actual spurious vector (0xff) is clearly
distiguished from the other vectors and also note for the vectored case
whether it was pending in the ISR or not.
"Spurious APIC interrupt (vector 0xFF) on CPU#0, should never happen."
"Spurious interrupt vector 0xed on CPU#1. Acked."
"Spurious interrupt vector 0xee on CPU#1. Not pending!."
Fixes: 2414e021ac ("x86: Avoid building unused IRQ entry stubs")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jan Beulich <jbeulich@suse.com>
Link: https://lkml.kernel.org/r/20190628111440.550568228@linutronix.de
Since the rework of the vector management, warnings about spurious
interrupts have been reported. Robert provided some more information and
did an initial analysis. The following situation leads to these warnings:
CPU 0 CPU 1 IO_APIC
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
clear_vector()
do_IRQ()
-> vector is clear
Before the rework the vector entries of legacy interrupts were statically
assigned and occupied precious vector space while most of them were
unused. Due to that the above situation was handled silently because the
vector was handled and the core handler of the assigned interrupt
descriptor noticed that it is shut down and returned.
While this has been usually observed with legacy interrupts, this situation
is not limited to them. Any other interrupt source, e.g. MSI, can cause the
same issue.
After adding proper synchronization for level triggered interrupts, this
can only happen for edge triggered interrupts where the IO-APIC obviously
cannot provide information about interrupts in flight.
While the spurious warning is actually harmless in this case it worries
users and driver developers.
Handle it gracefully by marking the vector entry as VECTOR_SHUTDOWN instead
of VECTOR_UNUSED when the vector is freed up.
If that above late handling happens the spurious detector will not complain
and switch the entry to VECTOR_UNUSED. Any subsequent spurious interrupt on
that line will trigger the spurious warning as before.
Fixes: 464d12309e ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>-
Tested-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.459647741@linutronix.de
BAU uses the old alloc_initr_gate90 method to setup its interrupt. This
fails silently as the BAU vector is in the range of APIC vectors that are
registered to the spurious interrupt handler. As a consequence BAU
broadcasts are not handled, and the broadcast source CPU hangs.
Update BAU to use new idt structure.
Fixes: dc20b2d526 ("x86/idt: Move interrupt gate initialization to IDT code")
Signed-off-by: Andrew Banman <abanman@hpe.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: Dimitri Sivanich <sivanich@hpe.com>
Cc: Russ Anderson <rja@hpe.com>
Cc: stable@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/1522188546-196177-1-git-send-email-abanman@hpe.com
There are no in-tree callers of ht_create_irq(), the driver interface for
HyperTransport interrupts, left. Remove the unused entry point and all the
supporting code.
See 8b955b0ddd ("[PATCH] Initial generic hypertransport interrupt
support").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pci@vger.kernel.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: https://lkml.kernel.org/r/20171122221337.3877.23362.stgit@bhelgaas-glaptop.roam.corp.google.com
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vector management state is not required to live in irq_cfg. irq_cfg is
only relevant for the depending irq domains (IOAPIC, DMAR, MSI ...).
The seperation of the vector management status allows to direct a shut down
interrupt to a special shutdown vector w/o confusing the internal state of
the vector management.
Preparatory change for the rework of managed interrupts and the global
vector reservation scheme.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.683712356@linutronix.de
Initialize the matrix allocator and add the proper accounting points to the
code.
No functional change, just preparation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.108410660@linutronix.de
No more users of the tracing IDT. All exception tracepoints have been moved
into the regular handlers. Get rid of the mess which shouldn't have been
created in the first place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170828064957.378851687@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's worth to avoid the extra irq_enter()/irq_exit() pair in the case that
the reschedule interrupt tracepoints are disabled.
Use the static key which indicates that exception tracing is enabled. For
now this key is global. It will be optimized in a later step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170828064957.299808677@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Two NOP5s are really a good tradeoff vs. the unholy IDT switching mess,
which duplicates code all over the place. The rescheduling interrupt gets
optimized in a later step.
Make the ordering of function call and statistics increment the same as in
other places. Calculate stats first, then do the function call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170828064957.222101344@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Machine checks are not really high frequency events. The extra two NOP5s for
the disabled tracepoints are noise vs. the heavy lifting which needs to be
done in the MCE handler.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170828064957.144301907@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Two NOP5s are a reasonable tradeoff to avoid duplicated code and the
requirement to switch the IDT.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/20170828064957.064746737@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The error and the spurious interrupt are really rare events and not at all
performance sensitive: two NOP5s can be tolerated when tracing is disabled.
Remove the complication.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170828064956.986009402@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Two NOP5s are really a good tradeoff vs. the unholy IDT switching mess,
which duplicates code all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170828064956.907209383@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The two NOP5s are noise in the rest of the work which is done by the timer
interrupt and modern CPUs are pretty good in optimizing NOPs anyway.
Get rid of the interrupt handler duplication and move the tracepoints into
the regular handler.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20170828064956.751247330@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are using the same vector for nested/non-nested posted
interrupts delivery, this may cause interrupts latency in
L1 since we can't kick the L2 vcpu out of vmx-nonroot mode.
This patch introduces a new vector which is only for nested
posted interrupts to solve the problems above.
Signed-off-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Harry reported, that he's able to trigger a system freeze with cpu hot
unplug. The freeze turned out to be a live lock caused by recent changes in
irq_force_complete_move().
When fixup_irqs() and from there irq_force_complete_move() is called on the
dying cpu, then all other cpus are in stop machine an wait for the dying cpu
to complete the teardown. If there is a move of an interrupt pending then
irq_force_complete_move() sends the cleanup IPI to the cpus in the old_domain
mask and waits for them to clear the mask. That's obviously impossible as
those cpus are firmly stuck in stop machine with interrupts disabled.
I should have known that, but I completely overlooked it being concentrated on
the locking issues around the vectors. And the existance of the call to
__irq_complete_move() in the code, which actually sends the cleanup IPI made
it reasonable to wait for that cleanup to complete. That call was bogus even
before the recent changes as it was just a pointless distraction.
We have to look at two cases:
1) The move_in_progress flag of the interrupt is set
This means the ioapic has been updated with the new vector, but it has not
fired yet. In theory there is a race:
set_ioapic(new_vector) <-- Interrupt is raised before update is effective,
i.e. it's raised on the old vector.
So if the target cpu cannot handle that interrupt before the old vector is
cleaned up, we get a spurious interrupt and in the worst case the ioapic
irq line becomes stale, but my experiments so far have only resulted in
spurious interrupts.
But in case of cpu hotplug this should be a non issue because if the
affinity update happens right before all cpus rendevouz in stop machine,
there is no way that the interrupt can be blocked on the target cpu because
all cpus loops first with interrupts enabled in stop machine, so the old
vector is not yet cleaned up when the interrupt fires.
So the only way to run into this issue is if the delivery of the interrupt
on the apic/system bus would be delayed beyond the point where the target
cpu disables interrupts in stop machine. I doubt that it can happen, but at
least there is a theroretical chance. Virtualization might be able to
expose this, but AFAICT the IOAPIC emulation is not as stupid as the real
hardware.
I've spent quite some time over the weekend to enforce that situation,
though I was not able to trigger the delayed case.
2) The move_in_progress flag is not set and the old_domain cpu mask is not
empty.
That means, that an interrupt was delivered after the change and the
cleanup IPI has been sent to the cpus in old_domain, but not all CPUs have
responded to it yet.
In both cases we can assume that the next interrupt will arrive on the new
vector, so we can cleanup the old vectors on the cpus in the old_domain cpu
mask.
Fixes: 98229aa36c "x86/irq: Plug vector cleanup race"
Reported-by: Harry Junior <harryjr@outlook.fr>
Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Joe Lawrence <joe.lawrence@stratus.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.11.1603140931430.3657@nanos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/include/asm/hw_irq.h contains declarations for the C-level handlers
called into directly from the IDT-referenced assembly stubs. These
declarations are never used as they are referenced from assembly only.
Furthermore, these declarations got their attributes wrong: there is no
'__irqentry' (parameter passing via stack) attached to them.
Also, the list of declarations isn't complete: none of the tracing-capable
variants is declared, for example.
Purge the handler declarations.
Signed-off-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Intel Volume Management Device (VMD) is a Root Complex Integrated
Endpoint that acts as a host bridge to a secondary PCIe domain. BIOS can
reassign one or more Root Ports to appear within a VMD domain instead of
the primary domain. The immediate benefit is that additional PCIe domains
allow more than 256 buses in a system by letting bus numbers be reused
across different domains.
VMD domains do not define ACPI _SEG, so to avoid domain clashing with host
bridges defining this segment, VMD domains start at 0x10000, which is
greater than the highest possible 16-bit ACPI defined _SEG.
This driver enumerates and enables the domain using the root bus
configuration interface provided by the PCI subsystem. The driver provides
configuration space accessor functions (pci_ops), bus and memory resources,
an MSI IRQ domain with irq_chip implementation, and DMA operations
necessary to use devices through the VMD endpoint's interface.
VMD routes I/O as follows:
1) Configuration Space: BAR 0 ("CFGBAR") of VMD provides the base
address and size for configuration space register access to VMD-owned
root ports. It works similarly to MMCONFIG for extended configuration
space. Bus numbering is independent and does not conflict with the
primary domain.
2) MMIO Space: BARs 2 and 4 ("MEMBAR1" and "MEMBAR2") of VMD provide the
base address, size, and type for MMIO register access. These addresses
are not translated by VMD hardware; they are simply reservations to be
distributed to root ports' memory base/limit registers and subdivided
among devices downstream.
3) DMA: To interact appropriately with an IOMMU, the source ID DMA read
and write requests are translated to the bus-device-function of the VMD
endpoint. Otherwise, DMA operates normally without VMD-specific address
translation.
4) Interrupts: Part of VMD's BAR 4 is reserved for VMD's MSI-X Table and
PBA. MSIs from VMD domain devices and ports are remapped to appear as
if they were issued using one of VMD's MSI-X table entries. Each MSI
and MSI-X address of VMD-owned devices and ports has a special format
where the address refers to specific entries in the VMD's MSI-X table.
As with DMA, the interrupt source ID is translated to VMD's
bus-device-function.
The driver provides its own MSI and MSI-X configuration functions
specific to how MSI messages are used within the VMD domain, and
provides an irq_chip for independent IRQ allocation to relay interrupts
from VMD's interrupt handler to the appropriate device driver's handler.
5) Errors: PCIe error message are intercepted by the root ports normally
(e.g., AER), except with VMD, system errors (i.e., firmware first) are
disabled by default. AER and hotplug interrupts are translated in the
same way as endpoint interrupts.
6) VMD does not support INTx interrupts or IO ports. Devices or drivers
requiring these features should either not be placed below VMD-owned
root ports, or VMD should be disabled by BIOS for such endpoints.
[bhelgaas: add VMD BAR #defines, factor out vmd_cfg_addr(), rework VMD
resource setup, whitespace, changelog]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de> (IRQ-related parts)
We can spare the irq_desc lookup in the interrupt entry code if we
store the descriptor pointer in the vector array instead the interrupt
number.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/20150802203609.717724106@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
VECTOR_UNDEFINED is a misnomer. The vector is defined, but unused.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: http://lkml.kernel.org/r/20150802203609.477282494@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently, we use a global vector as the Posted-Interrupts
Notification Event for all the vCPUs in the system. We need
to introduce another global vector for VT-d Posted-Interrtups,
which will be used to wakeup the sleep vCPU when an external
interrupt from a direct-assigned device happens for that vCPU.
[ tglx: Removed a gazillion of extra newlines ]
Signed-off-by: Feng Wu <feng.wu@intel.com>
Cc: jiang.liu@linux.intel.com
Link: http://lkml.kernel.org/r/1432026437-16560-4-git-send-email-feng.wu@intel.com
Suggested-by: Yang Zhang <yang.z.zhang@intel.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This routine has been around for over a decade, but with EISA
being dead and abandoned for about twice that long, the name can
be kind of confusing. The function is going at the PIC Edge/Level
Configuration Registers (ELCR), so rename it as such and mentally
decouple it from the long since dead EISA bus.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/1431217657-934-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Deferred errors indicate error conditions that were not corrected, but
require no action from S/W (or action is optional).These errors provide
info about a latent UC MCE that can occur when a poisoned data is
consumed by the processor.
Processors that report these errors can be configured to generate APIC
interrupts to notify OS about the error.
Provide an interrupt handler in this patch so that OS can catch these
errors as and when they happen. Currently, we simply log the errors and
exit the handler as S/W action is not mandated.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1430913538-1415-5-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Now we have dedicated asm/irqdomain.h, so move irqdomain specific
code into it.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/1428978610-28986-33-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Several fields in struct irq_cfg are private to vector.c, so move it
into dedicated data structure. This helps to hide implementation
details.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428978610-28986-27-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1416901802-24211-35-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Joerg Roedel <jroedel@suse.de>
Now there's no user of apic_set_affinity(), so remove it. Also rename
vector_set_affinity() to apic_set_affinity() for consistency.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428978610-28986-25-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Function {assign|clear}_irq_vector() and apic_retrigger_irq() are only
used in vector.c, so make them static.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428978610-28986-24-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now there is no user of irq_cfg.irq_remapped, so remove it.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: iommu@lists.linux-foundation.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Joerg Roedel <joro@8bytes.org>
Link: http://lkml.kernel.org/r/1428978610-28986-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enhance UV code to support hierarchical irqdomain, it helps to make
the architecture more clear.
We construct hwirq based on mmr_blade and mmr_offset, but mmr_offset
has type unsigned long, it may exceed the range of irq_hw_number_t. So
help about the way to construct hwirq based on mmr_blade and
mmr_offset is welcomed!
Folded a patch from Dimitri Sivanich <sivanich@sgi.com> to fix a bug
on UV platforms, please refer to:
http://lkml.org/lkml/2014/12/16/351
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russ Anderson <rja@sgi.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428905519-23704-23-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have slightly changed the architecture interfaces to support htirq
PCI driver. It's safe because currently Hypertransport interrupt is
only enabled on x86 platforms.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428905519-23704-22-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enhance DMAR code to support hierarchical irqdomain, it helps to make
the architecture more clear.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428905519-23704-21-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Enhance MSI code to support hierarchical irqdomains, it helps to make
the architecture more clear.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: iommu@lists.linux-foundation.org
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Joerg Roedel <joro@8bytes.org>
Link: http://lkml.kernel.org/r/1428905519-23704-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Introduce new interfaces for interrupt remapping drivers to support
hierarchical irqdomains:
1) irq_remapping_get_ir_irq_domain(): get irqdomain associated with an
interrupt remapping unit. IOAPIC/HPET drivers use this interface to
get parent interrupt remapping irqdomain.
2) irq_remapping_get_irq_domain(): get irqdomain for an IRQ allocation.
This is mainly used to support MSI irqdomain. We must build one MSI
irqdomain for each interrupt remapping unit. MSI driver calls this
interface to get MSI irqdomain associated with an IR irqdomain which
manages the PCI devices. In a further step we will store the irqdomain
pointer in the device struct to avoid this call in the irq allocation
path.
Architecture specific hooks:
1) arch_get_ir_parent_domain(): get parent irqdomain for IR irqdomain,
which is x86_vector_domain on x86 platforms.
2) arch_create_msi_irq_domain(): create an MSI irqdomain associated with
the interrupt remapping unit.
We also add following callbacks into struct irq_remap_ops:
struct irq_domain *(*get_ir_irq_domain)(struct irq_alloc_info *);
struct irq_domain *(*get_irq_domain)(struct irq_alloc_info *);
Once all clients of IR have been converted to the new hierarchical irqdomain
interfaces, we will:
1) Remove set_ioapic_entry, set_affinity, free_irq, compose_msi_msg,
msi_alloc_irq, msi_setup_irq, setup_hpet_msi from struct remap_osp
2) Remove setup_ioapic_remapped_entry, free_remapped_irq,
compose_remapped_msi_msg, setup_hpet_msi_remapped, setup_remapped_irq.
3) Simplify x86_io_apic_ops and x86_msi.
We can achieve a way clearer architecture with all these changes
applied.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: iommu@lists.linux-foundation.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Joerg Roedel <joro@8bytes.org>
Link: http://lkml.kernel.org/r/1428905519-23704-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Abstract CPU local APIC as an interrupt controller and create an
irqdomain for it to manage CPU interrupt vectors. It's the base to
enable hierarchical irqdomains on x86 systems.
The final irqdomain hierarchy will look like this:
IOAPIC domain ----|
MSI/MSI-x domain ----> [Interrupt Remapping domain] -> CPU vector domain
HPET_IRQ domain ----| ^
|
DMAR domain ----------------------------------------------|
HT_IRQ domain ----------------------------------------------|
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1428905519-23704-3-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cache destination CPU APIC ID into struct irq_cfg when assigning vector
for interrupt. Upper layer just needs to read the cached APIC ID instead
of calling apic->cpu_mask_to_apicid_and(), it helps to hide APIC driver
details from IOAPIC/HPET/MSI drivers..
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Link: http://lkml.kernel.org/r/1428905519-23704-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Interrupt entry points are handled with the following code,
each 32-byte code block contains seven entry points:
...
[push][jump 22] // 4 bytes
[push][jump 18] // 4 bytes
[push][jump 14] // 4 bytes
[push][jump 10] // 4 bytes
[push][jump 6] // 4 bytes
[push][jump 2] // 4 bytes
[push][jump common_interrupt][padding] // 8 bytes
[push][jump]
[push][jump]
[push][jump]
[push][jump]
[push][jump]
[push][jump]
[push][jump common_interrupt][padding]
[padding_2]
common_interrupt:
And there is a table which holds pointers to every entry point,
IOW: to every push.
In cold cache, two jumps are still costlier than one, even
though we get the benefit of them residing in the same
cacheline.
This change replaces short jumps with near ones to
'common_interrupt', and pads every push+jump pair to 8 bytes. This
way, each interrupt takes only one jump.
This change replaces ".p2align CONFIG_X86_L1_CACHE_SHIFT" before
dispatch table with ".align 8" - we do not need anything
stronger than that.
The table of entry addresses (the interrupt[] array) is no
longer necessary, the address of entries can be easily
calculated as (irq_entries_start + i*8).
text data bss dec hex filename
12546 0 0 12546 3102 entry_64.o.before
11626 0 0 11626 2d6a entry_64.o
The size decrease is because 1656 bytes of .init.rodata are
gone. That's initdata, though. The resident size does go up a
bit.
Run-tested (32 and 64 bits).
Acked-and-Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Will Drewry <wad@chromium.org>
Link: http://lkml.kernel.org/r/1428090553-7283-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Clean up code by moving IOAPIC related declarations from hw_irq.h into
io_apic.h.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Aubrey <aubrey.li@linux.intel.com>
Cc: Ryan Desfosses <ryan@desfo.org>
Cc: Quentin Lambert <lambert.quentin@gmail.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1414397531-28254-14-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create arch/x86/kernel/apic/vector.c to host local APIC related code,
prepare for making MSI/HT_IRQ independent of IOAPIC.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change irq_cfg() from static to extern, also introduce helper function
irqd_cfg(). Later we can rewrite these two helpers when enabling
hierarchy irqdomain.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Grant Likely <grant.likely@linaro.org>
Link: http://lkml.kernel.org/r/1414397531-28254-9-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
