Display WA #1178 is meant to fix Aux channel voltage swing too low with
some type C dongles. It applies to external ports on combo phy. On
Icelake this is port A and B when those are not eDP.
v2: follow the spec to the letter: include Aux A and just check if it's
not eDP instead of checking only for Aux B.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181012215758.25342-1-lucas.demarchi@intel.com
Right now RESET_PCH_HANDSHAKE_ENABLE is enabled all the times inside
of intel_power_domains_init_hw() and if PCH is NOP it is unsed in
i915_gem_init_hw().
So making skl_pch_reset_handshake() handle both cases and calling
it for the missing gens in intel_power_domains_init_hw().
Ivybridge have a different register and bits but with the same
objective so moving it too.
v2(Rodrigo):
- handling IVYBRIDGE case inside intel_pch_reset_handshake()
v4(Rodrigo and Ville):
- moving the enable/disable decision to callers
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918204714.27306-2-jose.souza@intel.com
Instead of have the same code spread into 4 platforms lets share it.
BXT do not have a PCH so here also handling this case by unseting
RESET_PCH_HANDSHAKE_ENABLE.
v2(Rodrigo):
- renamed to intel_pch_reset_handshake()
- added comment about why BXT need the bit to be unset
v3(Rodrigo and Ville):
- added bool have_pch to intel_pch_reset_handshake()
- added back BXT comment
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918204714.27306-1-jose.souza@intel.com
PSR requires AUX IO power well to be enabled. This was already in place
for CNL, extend this for ICL too. Not enabling the power well results in
the aux error interrupts when the hardware exits PSR.
Reported-by: Casey G Bowman <casey.g.bowman@intel.com>
Reported-by: Jyoti R Yadav <jyoti.r.yadav@intel.com>
Cc: Matt Atwood <matthew.s.atwood@intel.com>
Cc: Jyoti R Yadav <jyoti.r.yadav@intel.com>
Cc: Casey G Bowman <casey.g.bowman@intel.com>
Tested-by: Casey G Bowman <casey.g.bowman@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180914001822.2503-1-dhinakaran.pandiyan@intel.com
Add Support to load DMC on Icelake.
While at it, also add support to load the firmware
during system resume.
v2: load firmware during system resume.(Imre)
v3: enable has_csr for icelake.(Jyoti)
v4: Only load the firmware in this patch
Cc: Jyoti Yadav <jyoti.r.yadav@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828003844.4682-2-anusha.srivatsa@intel.com
During power domains initialization we acquire power well references for
power wells in the INIT power domain. The rest of power wells - which
BIOS could have left enabled - we can only acquire references as needed
during display HW readout and so must defer sanitization until then
(also implying that we must always do HW readout to cleanup unused power
wells).
Thus during initialization these latter power wells can have a refcount
of 0 while still being enabled. To avoid the false-positive state
mismatch error this causes remove the check from
intel_power_domains_init_hw() and rely on the state check in
intel_power_domains_enable() which follows the HW readout.
v2:
- Add comment to log and code clarifying how unused power wells get
disabled. (Chris)
Fixes: 6dfc4a8f13 ("drm/i915: Verify power domains after enabling them")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: https://bugs.freedesktop.org/show_bug.cgi?id=107411
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180828122231.14336-1-imre.deak@intel.com
None of the current lookup_power_well() callers are actually checking
for NULL return values, they all just use the pointer right away. The
first idea was to replace these theoretical segfaults with a BUG()
since this would at least make our code a little more explicit to the
reader. It was suggested that just converting the BUG() to a WARN()
and returning any power well would probably be better since it would
still keep the system running while at the same time exposing the
driver bug.
We can only hit this NULL/BUG()/WARN() condition if we try to lookup a
power well that isn't defined on a given platform. If that ever
happens, we have to fix our code, making it lookup the correct power
well. Because of this, I don't think it's worth trying to implement
error checking in every caller. Improving our CI system will be a
better use of our time once a bug is found in the wild.
v2: Avoid the BUG() with a WARN() return a random PW (Michal).
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180820233139.11936-2-paulo.r.zanoni@intel.com
For S0ix we want to deinit power domains (and so deactivate the DMC
firmware) exactly when the platform supports the DC9 state. To reach
S0ix we need DC9 on these platforms (for which the DMC FW needs to be
deactivated) while to reach S0ix on the rest of the DMC platforms we
need DC6 (which needs the DMC FW to stay active).
Simplify the condition accordingly so it will be automatically
correct for upcoming DC9 platforms like ICL.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180822112602.27543-1-imre.deak@intel.com
After
commit 2cd9a689e9 ("drm/i915: Refactor intel_display_set_init_power() logic")
it makes more sense to check the power domain/well refcounts after
enabling the power domains functionality. Before that it's guaranteed
that most power wells (in the INIT domain) will have a reference held,
so not an interesting state.
While at it also add the check after the init_hw/fini_hw, disable and
suspend/resume steps. Make the test optional on a Kconfig option since
it may add substantial overhead: on VLV/CHV the corresponding PUNIT reg
access for each power well may take up to 20ms.
v2:
- Add the state check to more spots. (Chris)
v3:
- During suspend check the state before deiniting display core.
Afterwards DC states are disabled (and so the dc_off power well is
enabled) even though we don't hold a reference on it.
- Do the test conditionally based on a new Kconfig option. (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Add DRM_I915_DEBUG_RUNTIME_PM to welcome messages]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180817145837.26592-1-imre.deak@intel.com
The device global init_power_on flag is somewhat arbitrary and makes
debugging power refcounting problems difficult. Instead arrange things
so that all display power domain get has a corresponding put call. After
this change we have the following sequences:
driver loading:
intel_power_domains_init_hw();
<other init steps>
intel_power_domains_enable();
driver unloading:
intel_power_domains_disable();
<other uninit steps>
intel_power_domains_fini_hw();
system suspend:
intel_power_domains_disable();
<other suspend steps>
intel_power_domains_suspend();
system resume:
intel_power_domains_resume();
<other resume steps>
intel_power_domains_enable();
at other times while the driver is loaded:
intel_display_power_get();
...
intel_display_power_put();
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-2-imre.deak@intel.com
Currently, we cancel the extra wakeref we have for !runtime-pm devices
inside power_wells_fini_hw. However, this is not strictly paired with
the acquisition of that wakeref in runtime_pm_enable (as the fini_hw may
be called on errors paths before we even call runtime_pm_enable). Make
the symmetry more explicit and include a check that we do release all of
our rpm wakerefs.
v2: Fixup transfer of ownership back to core whilst keeping our wakeref
count balanced.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180816123757.3286-1-imre.deak@intel.com
There is no need for separate IDs for power wells on a new platform with
the same functionality as an other power well on a previous platform, we
can just reuse the ID from the previous platform. This is only possible
after the previous patches where we removed dependence on the actual
enum values.
This also fixes a problem on ICL where in assert_can_enable_dc5/9() we
would've failed to look up the PW#2 power well.
v2:
- Keep an ID assigned for the ICL PW#2 power well too. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Added comment about the ICL PW#2 fix to the commit log]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-10-imre.deak@intel.com
The format for the ID names is <platform>_DISP_PW_* so rename the IDs
not following this accordingly. Leave BXT_DPIO_CMN_BC as-is since we'll
change that to use another existing ID in the next patch.
v2:
- Fix line over 80 chars checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-9-imre.deak@intel.com
Now that we removed dependence on the power well IDs to determine the
control register and request/status flag offsets the only purpose of
power well IDs is to look up power wells directly bypassing the power
domains framework. However this direct lookup isn't needed for most of
the exisiting power wells and hopefully won't be needed for any new
power wells in the future. To make maintenance of the power well ID enum
easier, don't require a unique ID for each power well, only if it's
necessary. Remove the IDs becoming redundant this way and assign to all
the corresponding power wells a new DISP_PW_ID_NONE ID.
After the previous two patches the IDs don't need to have a fixed value,
so remove the explicit initializers and adjust the enum's code comment
accordingly.
v2:
- Keep required ID assignments for HSW_DISP_PW_GLOBAL and ICL_DISP_PW_2.
(Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-8-imre.deak@intel.com
Similarly to the previous patch use a separate request/status HW flag
index defined right after the corresponding control registers instead of
depending for this on the power well IDs. Since the set of
control/status registers varies among the different power wells (on a
single platform), also add a new i915_power_well_registers struct that
we populate and assign to each DDI power well as needed.
Also clarify a bit the code comment describing the function and layout
of the control registers.
This also fixes a problem on ICL, where we incorrectly read the KVMR
control register in hsw_power_well_requesters() even for DDI and AUX
power wells.
v2:
- Clarify platform range tags in code comments. (Paulo)
- Fix line over 80 chars checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-7-imre.deak@intel.com
Atm, we determine the control/status flag offsets within the PUNIT
control/status registers based on the power well's ID. Since the power
well ID enum is global across all platforms, the associated macros to
get the flag offsets involves some magic. This makes checking the
register/bit definitions against the specification more difficult than
necessary. Also the values in the power well ID enum must stay fixed,
making code maintenance of the enum cumbersome.
To solve the above define the control/status flag indices right after
the corresponding registers and use these to derive the control/status
flag values by storing the indices in the i915_power_well_desc struct.
Initializing anonymous union fields require the preceding field in the
struct to be explicitly initialized - even when using named
initializers - and the initialization to be done right before the union
initialization, hence the reordering of the .id fields.
v2:
- Clarify commit log message about anonymous union initializers. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-6-imre.deak@intel.com
It makes sense to keep unchanging data const. Extract such fields from
the i915_power_well struct into a new i915_power_well_desc struct that
we initialize during compile time. For the rest of the dynamic
fields allocate an array of i915_power_well objects in i915 dev_priv,
and link to each of these objects their corresponding
i915_power_well_desc object.
v2:
- Fix checkpatch warnings about missing param name in fn declaration and
lines over 80 chars. (Paulo)
- Move check for unique IDs to __set_power_wells().
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Fixed checkpatch warn in __set_power_wells()]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-5-imre.deak@intel.com
The callbacks these asserts are called from are used from a single power
well, so not much point in checking that. The check also requires a unique
power well ID that we would need to keep around only for this purpose.
(A follow-up patch removes power well IDs not needed for direct power
well access).
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-4-imre.deak@intel.com
intel_power_domains_fini() rolls back what was done in
intel_power_domains_init_hw(), so rename and move it accordingly. This
allows us adding a cleanup function later for intel_power_domains_init()
in a cleaner way.
No functional change.
v2:
- Fix checkpatch error adding missing param name to function
declaration. (Paulo)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-3-imre.deak@intel.com
Similarly to commit 0a445945be
("drm/i915: Work around GCC anonymous union initialization bug")
we need to initialize anonymous unions inside extra braces to work
around a GCC4.4 build error.
v2:
- Fix checkpatch errors in commit log. (Paulo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806095843.13294-2-imre.deak@intel.com
The new recommendation from the spec is to simply not set this bit
anymore. Not setting the bit would prevent some hangs that our driver
manages to avoid since commit c8af5274c3 ("drm/i915: enable the
pipe/transcoder/planes later on HSW+"), and the theoretical downside
of not setting the bit doesn't seem realistic according to the HW
team. Let's follow their recommendation.
BSpec: 20233
References: commit c8af5274c3 ("drm/i915: enable the
pipe/transcoder/planes later on HSW+")
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180726001229.13791-1-paulo.r.zanoni@intel.com
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 141432
Addresses-Coverity-ID: 141433
Addresses-Coverity-ID: 141434
Addresses-Coverity-ID: 141435
Addresses-Coverity-ID: 141436
Addresses-Coverity-ID: 1357360
Addresses-Coverity-ID: 1357403
Addresses-Coverity-ID: 1357433
Addresses-Coverity-ID: 1392622
Addresses-Coverity-ID: 1415273
Addresses-Coverity-ID: 1435752
Addresses-Coverity-ID: 1441500
Addresses-Coverity-ID: 1454596
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180628223541.GA17665@embeddedor.com
Add the definition for ICL power wells and their mapping to power
domains. On ICL there are 3 power well control registers, we'll select
the correct one based on higher bits of the power well ID. The offset
for the control and status flags within this register is based on the
lower bits of the ID as on older platforms.
As the DC state programming is also the same as on old platforms we can
reuse the corresponding helpers. For this we mark here the DC-off power
well as shared among multiple platforms.
Other than the above the delta between old platforms and ICL:
- Pipe C has its own power well, so we can save some additional power in the
pipe A+B and (non-eDP) pipe A configurations.
- Power wells for port E/F DDI/AUX IO and Thunderbolt 1-4 AUX IO
v2:
- Rebase on drm-tip after prep patch for this was merged there as
requested by Paulo.
- Actually add the new AUX and DDI power well control regs (Rakshmi)
v3:
- Fix power well register names in code comments
- Add TBT AUX->power well 3 dependency
v4:
- Rebase
v5:
- Detach AUX power wells from the INIT power domain. These power wells
can only be enabled in a TC/TBT connected state and otherwise not
needed during driver initialization.
v6:
- Use _MMIO_PORT(...) instead _MMIO(_PICK(...)) (Paulo)
Fix checkpatch warnings.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rakshmi Bhatia <rakshmi.bhatia@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com> (v1)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180626142232.22361-1-imre.deak@intel.com
So far we got an AUX power domain reference only for the duration of DP
AUX transfers. However, the following suggests that we also need these
for main link functionality:
- The specification doesn't state whether it's needed or not for main
link functionality, but suggests that these power wells need to be
enabled already during display core initialization (Sequences to
Initialize Display).
- For PSR we need to keep the AUX power well enabled.
- On ICL combo PHY ports (non-TC) the AUX power well is needed for
link training too: while the port is enabled with a DP link training
test pattern trying to toggle the AUX power well will time out.
- On ICL MG PHY ports (TC) the AUX power well is needed also for main
link functionality (both in DP and HDMI modes).
- Windows enables these power wells both for main and AUX lane
functionality.
Based on the above take an AUX power reference for main link
functionality too. This makes a difference only on GEN10+ (GLK+)
platforms, where we have separate port specific AUX power wells.
For PSR we still need to distinguish between port A and the other
ports, since on port A DC states must stay enabled for main link
functionality, but DC states must be disabled for driver initiated
AUX transfers. So re-use the corresponding helper from intel_psr.c.
Since we take now a reference for main link functionality on all DP
ports we can forgo taking the separate power ref for PSR functionality.
v2:
- Make sure DC states stay enabled when taking the ref on port A.
(Ville)
v3: (Ville)
- Fix comment about logic for encoders without a crtc state and
add FIXME note for a simplification to avoid calling get_power_domains
in such cases.
- Use intel_crtc_has_dp_encoder() instead !intel_crtc_has_type(HDMI).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
[Clarified code comments in intel_ddi_main_link_aux_domain() and
intel_ddi_get_power_domains() (Imre)]
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180621184449.26634-1-imre.deak@intel.com
Add support for DP_AUX_E. Here we also introduce the bits for the AUX
power well E, however ICL power well support is still not enabled yet,
so the power well is not used.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180612002512.29783-2-paulo.r.zanoni@intel.com
Add documentation to gen9_set_dc_state() on what enabling a given DC
state means and at what point HW/DMC actually enters/exits these states.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180417113147.25120-1-imre.deak@intel.com
ICL has two slices of DBuf, each slice of size 1024 blocks.
We should not always enable slice-2. It should be enabled only if
display total required BW is > 12GBps OR more than 1 pipes are enabled.
Changes since V1:
- typecast total_data_rate to u64 before multiplication to solve any
possible overflow (Rodrigo)
- fix where skl_wm_get_hw_state was memsetting ddb, resulting
enabled_slices to become zero
- Fix the logic of calculating ddb_size
Changes since V2:
- If no-crtc is part of commit required_slices will have value "0",
don't try to disable DBuf slice.
Changes since V3:
- Create a generic helper to enable/disable slice
- don't return early if total_data_rate is 0, it may be cursor only
commit, or atomic modeset without any plane.
Changes since V4:
- Solve checkpatch warnings
- use kernel types u8/u64 instead of uint8_t/uint64_t
Changes since V5:
- Rebase
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-3-mahesh1.kumar@intel.com
This patch adds support to start tracking status of DBUF slices.
This is foundation to introduce support for enabling/disabling second
DBUF slice dynamically for ICL.
Changes Since V1:
- use kernel type u8 over uint8_t
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180426142517.16643-2-mahesh1.kumar@intel.com
One is outright unused, other can be made static.
Drive-by cleanup while accidentally reading dc code.
Cc: Imre Deak <imre.deak@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180417100225.12286-1-daniel.vetter@ffwll.ch
The DMC FW specific part of display WA#1183 is supposed to be enabled
whenever enabling DC5 or DC6, so move it to the DC6 enable function
from the DC6 disable function.
I noticed this after Daniel's patch to remove the unused
skl_disable_dc6() function.
Fixes: 53421c2fe9 ("drm/i915: Apply Display WA #1183 on skl, kbl, and cfl")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419155109.29451-1-imre.deak@intel.com
PSR on CNL requires AUX IO wells to be kept on and the existing AUX domain
for AUX-A enables DC_OFF well too. This is not required, so add a new
AUX_IO_A domain for AUX-A to allow DC states to remain enabled. Other AUX
channels re-use the existing AUX domains.
v4: Reword comment (Rodrigo and Ville)
Rename _get and _put functions to include aux_io substring(Rodrigo)
Remove unnecessary diff that got included.
v3: Extract aux domain selection into a function (Ville)
v2: Add AUX IO domain only for AUX-A
Rebased on top of Ville's AUX series.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223221520.18464-1-dhinakaran.pandiyan@intel.com
This patch initializes MBus during display initialization.
Changes since V2 (from Paulo):
- Don't forget to remove the WARN_ON(1) call.
Changes since V1:
- Rebase to use function like Macros
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-6-paulo.r.zanoni@intel.com
ICL has 2 slices of DBuf, enable both the slices during display init.
Ideally we should only enable the second slice when needed in order to
save power, but while we're not there yet, adopt the simpler solution
to keep us bug-free.
v2 (from Paulo):
- Add the TODO comment.
- Reorganize where things are defined.
- Fix indentation.
- Remove unnecessary POSTING_READ() calls.
- Improve the commit message.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-5-paulo.r.zanoni@intel.com
This code is similar enough to the CNL code that I considered just
adding ICL support to the CNL function, but I think it's still
different enough, and having a function specific to ICL allows us to
more easily adapt code in case the spec changes more later.
We're still missing the power wells and the mbus code, so leave those
pieces with a FIXME comment while they're not here yet.
v2: Don't use _PICK, don't WARN_ON(1), don't forget the chicken bits.
v3: Use _MMIO_PORT() (Ville).
Reviewed-by: James Ausmus <james.ausmus@intel.com> (v2)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-4-paulo.r.zanoni@intel.com
On ICL we have two sets of registers: one for port A and another for
port B. The set of port A registers is the same as the CNL registers.
Since the procmon table on ICL is the same we want to reuse the CNL
function. To do that we add a port argument and make CNL always call
the function passing port A. This way, we'll be able to easily reuse
the function on ICL when we add icl_display_core_init().
v2: Don't use _PICK() when you can use a ternary operator.
v3: Don't use a ternary operation when you can use _MMIO_PORT (Ville).
Add an extra comment about why we're passing PORT_A (James).
Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205154046.11485-2-paulo.r.zanoni@intel.com
Now let's finish the Port-F support by adding the
proper port F detection, irq and power well support.
v2: Rebase
v3: Use BIT_ULL
v4: Cover missed case on ddi init.
v5: Update commit message.
v6: Rebase on top of display headers rework.
v7: Squash power-well handling related to DDI F to this
patch to avoid warns as pointed out by DK.
v8: Introduce DDI_F_LANES to PG2. (DK)
v9: Squash in the PORT_F case for enabling DP MST encoder. (DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-9-rodrigo.vivi@intel.com
On some Cannonlake SKUs we have a dedicated Aux for port F,
that is only the full split between port A and port E.
There is still no Aux E for Port E, as in previous platforms,
because port_E still means shared lanes with port A.
v2: Rebase.
v3: Add couple missed PORT_F cases on intel_dp.
v4: Rebase and fix commit message.
v5: Squash Imre's "drm/i915: Add missing AUX_F power well string"
v6: Rebase on top of display headers rework.
v7: s/IS_CANNONLAKE/IS_CNL_WITH_PORT_F (DK)
v8: Fix Aux bits for Port F (DK)
v9: Fix VBT definition of Port F (DK).
v10: Squash power well addition to this patch to avoid
warns as pointed by DK.
v11: Clean up squashed commit message. (David)
v12: Remove unnecessary handling for older platforms (DK)
Adding AUX_F to PG2 following other existent ones. (DK)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180129232223.766-2-rodrigo.vivi@intel.com
Display WA #1178 is meant to fix Aux channel voltage swing too low with
some type C dongles. Although it is for type C, HW engineers reported
that it can be applied to all external ports even if they are not going
to type C.
For CNL we apply the workaround every time Aux B, C and D are powering
up since they will lose the configuration when powered down.
v2: Use common tag for WA
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171128220553.22435-1-lucas.demarchi@intel.com
With firmware 1.07 having fixed the state corruption issue, we can enable
the headless GT performance workaround for CNL as well. (Equivalent to
b68763741a ("drm/i915: Restore GT performance in headless mode with DMC
loaded") on other affected platforms.)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180111082417.795-1-tvrtko.ursulin@linux.intel.com
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
It seems that the DMC likes to transition between the DC states a lot when
there are no connected displays (no active power domains) during command
submission.
This activity on DC states has a negative impact on the performance of the
chip with huge latencies observed in the interrupt handlers and elsewhere.
Simple tests like igt/gem_latency -n 0 are slowed down by a factor of
eight.
Work around it by introducing a new power domain named,
POWER_DOMAIN_GT_IRQ, associtated with the "DC off" power well, which is
held for the duration of command submission activity.
CNL has the same problem which will be addressed as a follow-up. Doing
that requires a fix for a DC6 context corruption problem in the CNL DMC
firmware which is yet to be released.
v2:
* Add commit text as comment in i915_gem_mark_busy. (Chris Wilson)
* Protect macro body with braces. (Jani Nikula)
v3:
* Add dedicated power domain for clarity. (Chris, Imre)
* Commit message and comment text updates.
* Apply to all big-core GEN9 parts apart for Skylake which is pending DMC
firmware release.
v4:
* Power domain should be inner to device runtime pm. (Chris)
* Simplify NEEDS_CSR_GT_PERF_WA macro. (Chris)
* Handle async DMC loading by moving the GT_IRQ power domain logic into
intel_runtime_pm. (Daniel, Chris)
* Include small core GEN9 as well. (Imre)
v5
* Special handling for async DMC load is not needed since on failure the
power domain reference is kept permanently taken. (Imre)
v6:
* Drop the NEEDS_CSR_GT_PERF_WA macro since all firmwares have now been
deployed. (Imre, Chris)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100572
Testcase: igt/gem_exec_nop/headless
Cc: Imre Deak <imre.deak@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dmitry Rogozhkin <dmitry.v.rogozhkin@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v5)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[Imre: Add note about applying the WA on CNL as a follow-up]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205132854.26380-1-tvrtko.ursulin@linux.intel.com
For CNL we'll need to start considering the port clocks when we select
the voltage level for the system agent. To that end start tracking the
voltage in the cdclk state (since that already has to adjust it).
v2: s/voltage/voltage_level/ (Rodrigo)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-3-ville.syrjala@linux.intel.com
In order to separate GT PM related functionality into new structure
we are updating rps structure. hw_lock in it is used for display
related PCU communication too hence move it to dev_priv.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Radoslaw Szwichtenberg <radoslaw.szwichtenberg@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/1507360055-19948-8-git-send-email-sagar.a.kamble@intel.com
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010213010.7415-7-chris@chris-wilson.co.uk
