dtc now gives the following warning:
arch/arm/boot/dts/kirkwood-t5325.dtb: Warning (sound_dai_property): /sound/simple-audio-card,cpu:sound-dai: property size (4) too small for cell size 1
The binding documentation gives no indication what the cell size should
be (which should be fixed too), so just assume 0 is fine as that is what
the consumer has.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Replace sdio2 rcc hard coded clock value by its macro.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f769-disco board.
broken-cd property is needed as it misses a pullup on board
(resistor R76 is missing).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Adds SDIO related DT nodes for stm32f746-eval board.
broken-cd property is needed as card detect signal is
connected to a GPIO expander which is not yet supported
in kernel linux.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds all SPI instances of the STM32H743 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add sound support to Motorola Droid 4 using simple-soundcard
and CPCAP's audio codec. This does not yet correctly represent
the whole audio routing, since McBSP3 is also connected to
Bluetooth and MDM6600 modem (and probably also 4G modem).
These extra DAI links are not yet supported and have not been
tested.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for audio-codec to its DT file.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dtc now gives the following warnings:
arch/arm/boot/dts/omap3-gta04a3.dtb: Warning (sound_dai_property): /sound_telephony/simple-audio-card,cpu: Missing property '#sound-dai-cells' in node /ocp@68000000/mcbsp@49026000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/omap3-gta04a4.dtb: Warning (sound_dai_property): /sound_telephony/simple-audio-card,cpu: Missing property '#sound-dai-cells' in node /ocp@68000000/mcbsp@49026000 or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/omap3-gta04a5.dtb: Warning (sound_dai_property): /sound_telephony/simple-audio-card,cpu: Missing property '#sound-dai-cells' in node /ocp@68000000/mcbsp@49026000 or bad phandle (referred from sound-dai[0])
Add the missing #sound-dai-cells property.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The EMIF instance on am43xx supports interrupts, so add the info for
completeness sake. Right now, the driver does not use this for anything,
but it is possible it would be used in future.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The EMIF instance on am33xx supports interrupts, so add the info for
completeness sake. Right now, the driver does not use this for anything,
but it is possible it would be used in future.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since I2C1 and I2C4 have explicit pinmuxing set, let's be on the
safe side and set the pin muxing for I2C2 and I2C3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
This is specific to am57xx-idk (and not all dra72/dra74 based boards)
since mmc1_clk line in am57xx-idk is not connected to an external
pullup.
While at that change the order of header files in am571x-idk.dts and
am572x-idk.dts so that the modified pinctrl values in am57xx-idk-common
could take effect.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
This is specific only to dra71-evm (and not all dra72 based boards) since
mmc1_clk line in dra71-evm is not connected to an external pullup.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correct vpo_sd_1v8_3v3 regulator max voltage to 3.3V
Fixes: 9868bc585ae2 ("ARM: dts: Add support for dra718-evm")
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc specific pinmux is selected from dra74x-mmc-iodelay.dtsi, so remove
it in dra7-evm.dts
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add "vqmmc-supply" property for mmc2 to indicate the supply connected
to the IO lines.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SD card interface on DRA76x EVM can support
high speed SD cards. The eMMC onboard can support
upto HS200 mode.
Enable support for these higher speed modes in the
device-tree file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we have a device-tree include file with common
MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree
file to using that.
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a common device-tree include file with MMC/SD IOdelay data
for DRA76x SoC.
In the most common case, IOdelay data available in datamanual
can directly be used. This file caters to that common case.
Data is based on DRA76x datamanual, SPRS993A, revised July 2017.
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
4.16, please pull the following:
- Mathieu fixes leading 0x and 0's from bindings and Device Tree source
files, he has done this treewide and most of his changes are already in
4.16
- Stefan provides two changes to the BCM283x DTS files in order to fix
DTC warnings
- Florian fixes the amount of RAM on the BCM958625HR reference board to
properly limit to what is initialized by the bootloader
-----BEGIN PGP SIGNATURE-----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=9RVY
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.16/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
Pull "Broadcom devicetree fixes for 4.16" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
4.16, please pull the following:
- Mathieu fixes leading 0x and 0's from bindings and Device Tree source
files, he has done this treewide and most of his changes are already in
4.16
- Stefan provides two changes to the BCM283x DTS files in order to fix
DTC warnings
- Florian fixes the amount of RAM on the BCM958625HR reference board to
properly limit to what is initialized by the bootloader
* tag 'arm-soc/for-4.16/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Move arm-pmu out of soc node
ARM: dts: bcm283x: Fix unit address of local_intc
ARM: dts: NSP: Fix amount of RAM on BCM958625HR
ARM: BCM: dts: Remove leading 0x and 0s from bindings notation
- Fix i.MX GPC driver to remove power domains only when they are
initialized in imx_gpc_probe().
- Fix the broken Engicam i.CoreM6 DualLite/Solo RQS board DT to include
imx6dl.dtsi instead of imx6q.dtsi.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJalfO8AAoJEFBXWFqHsHzOPk4IALx0Gl07tgaTy2VgZJT2w0ud
ZoyeicSNxfM42auRHjC6QhYpQztw8+k4PCuGmUOutHc2Hbw21EXDxLiSwYgGarBR
3OuYShxBg6IExpUk7TM0kDFU0Z4GcpTjAovloM7yjLxCj88dzS+NIiUwPSl02kTp
iAGxVtTQOYLotJFZLQ+DGH3SuaEvOEzeQZz/v4v2/z1IsJRI5IQ2ILtSFEOYhMwh
vgagvvHopS2jIfLXd47PJJvUQuRjXH00FMvrEmBT2b31HJDU2uKn+y4BtMCJHzJV
cTaCwKcrJcLCH2tv5LVUg86VcbL7qbMGjqKQk4aSuEtMtJkpkD4palNG+y69N9g=
=NKMF
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "i.MX fixes for 4.16" from Shawn Guo:
- Fix i.MX GPC driver to remove power domains only when they are
initialized in imx_gpc_probe().
- Fix the broken Engicam i.CoreM6 DualLite/Solo RQS board DT to include
imx6dl.dtsi instead of imx6q.dtsi.
* tag 'imx-fixes-4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6 DualLite/Solo RQS
soc: imx: gpc: de-register power domains only if initialized
The ARM PMU doesn't have a reg address, so fix the following DTC warning
(requires W=1):
Node /soc/arm-pmu missing or empty reg/ranges property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.
The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.
Fixes: c53beb47f6 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
We can never idle the l3_main hwmod so mark the omap_l3_noc node
with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can never idle the emif hwmod from within the HLOS so mark the emif
node with ti,no-idle.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add soc node for am4372 with pm-sram phandle to both pm-sram-code and
pm-sram-data regions.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a phandle to point to both the pm-sram-code and pm-sram-data nodes
so that the pm code can locate the sram regions needed to copy low level
PM code.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am4372 PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we will use ti-emif-sram driver for am335x PM, update the
emif DT node with the required sram property.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a 'pm_sram_code' reserved region to the ocmcram node to be exposed
by the mmio-sram driver as a pool but also mark it protect-exec so that
it can run code copied to it using sram_exec_copy.
Add another 'pm_sram_data' reserved region to the ocmcram node to act as
the data space for any code running from the 'pm_sram_code' region that
is exposed as a regular pool.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for RTC on STM32H743 SoC.
It also adds dt-bindings/interrupt-controller/irq.h include and uses it to
configure RTC alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32h743i-eval in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS and FS on STM32H743 SoC:
-USB OTG HS controller is the same than the one used on STM32F7 SoCs.
-USB OTG FS controller is the same than the one used on STM32F4 SoCs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32f749-disco in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure USB OTG HS in OTG (DRD) mode on STM32746G_eval.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
USB OTG HS on STM32F746 can also be used as Peripheral (gadget), so
this patch adds DWC2 gadget mode fifo sizes bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The HSE oscillator frequency was wrongly set to 125MHz instead of 25MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 9273083a15 ("usb: dwc2: Fix TxFIFOn sizes and total TxFIFO
size issues") we could use the OTG mode again.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add BCM43438 (bluetooth) as a serdev slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on patched userspace helpers (hciattach).
In order to keep a debug UART we need to switch to uart1.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Instead of keeping the firmware's pull settings, we better apply
them via the devicetree pin control. Start with the RPi Zero W relevant
first to keep the effort low.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This stops the driver from trying to probe the ATA slave
interface. The vendor code enables the slave interface
but the driver in the vendor tree does not make use of
it.
Setting it to muxmode 0 disables the slave interface:
the hardware only has the master interface connected
to the one harddrive slot anyways.
Without this change booting takes excessive time, so it
is very annoying to end users.
Fixes: dd5c0561db ("ARM: dts: Add basic devicetree for D-Link DNS-313")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
PMIC node requires external interrupts for proper operation, but property
defining them was missing. This was probably caused by a limited support
for interrupts from more than one parent, which was not possible to define
when support for this board was added. Fix this by adding
'interrupt-extended' property and properly define interrupt lines for PMIC
node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Fix the unit addresses of PDMA nodes in Exynos5410 (the reg property is
correct) to get rid of DTC warnings like:
arch/arm/boot/dts/exynos5410-odroidxu.dtb: Warning (simple_bus_reg):
Node /soc/amba/pdma@12680000 simple-bus unit address format error, expected "121a0000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Typo in unit address of PPMU ACP caused DTC warnings:
arch/arm/boot/dts/exynos4412-odroidu3.dtb:
Warning (simple_bus_reg): Node /soc/ppmu_acp@10ae0000 simple-bus unit address format error, expected "106e0000"
PPMU ACP (under 0x10ae0000 address) is present only in Exynos4210 so
move this node to exynos4210.dtsi with fixing the reg address to proper
one.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch will add the chosen container to point stdout-path to serial2
and set the alias for spi0 to spi1 since the SPI NOR flash exists on SPI1.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now require all at24 users to use the "atmel,<model>" fallback in
device tree for different manufacturers.
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch fixes the wrongly included dtsi file which
was breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
As per the board name, the correct file should be imx6dl.dtsi instead
of imx6q.dtsi
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fixes: 7a9caba55a ("ARM: dts: imx6dl: Add Engicam i.CoreM6 DualLite/Solo RQS initial support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a new node for reboot modes on LEGO MINDSTORMS EV3. The EV3's
bootloader looks for a magic number in the ARM local RAM and if found,
it will boot into a special firmware update mode where the flash memory
can be written via USB.
This has been testing working using the command:
# systemctl reboot loader
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a description of the RPi3 GPIO expander that the VC4 firmware controls.
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This allows adding devices for which the firmware exposes control interface
via the mailbox. An example of such device is the GPIO expander.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
the bcm2835-i2s requires a clock as DT property. Unfortunately
the necessary DT change has never been applied. While we are at it
also fix the first PCM register range to cover the PCM_GRAY register.
Fixes: 517e7a1537 ("ASoC: bcm2835: move to use the clock framework")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13
carry altenate function, ALT5 for ARM JTAG
Fixes: 21ff843931 ("ARM: dts: bcm283x: Define standard pinctrl groups in the gpio node.")
Signed-off-by: Henry Zhang <henryzhang62@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Device nodes in device tree should use generic names, so rename
all existing power domains to "power-domain". To keep readable domain
names in debug logs, use label property, which has been introduce by
commit b13b2330aa ("soc: samsung: pm_domains: Read domain name from
the new label property");
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This adds support for the MMS152 found on N710x boards.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlqHdYgQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWwyCACeLElOaIYbFWectAjRvpYhOBMwk4mk/qA+
R5MLVhYRBshyb7KcTG4aBuP/FjrY68BllkxR5ANSF0GZCvvxTGgW3/XCouTRtRjd
YLIMlVKZZPokXEYxN1lqwgJjPx0pHBmDjwWcmU1cJ0gr6z5+/lPwYQW1x43S/yqd
T01vP7TsltG7U5Ai+prQfnWkjcKbPZUEqxDtWIRHqNeudJbcIoiWCOC4H+kYbygN
/w9UvaqGdD97Zs//v3jSxxB9CDdX3EScbPPSLhwFjj5Zckm6GJBRSbO2TWnsPv/H
Ed83duV1eSfIePbRIu2Qk6XrUdFU37GKlNA9SNDE58nphYTW7y2R
=Rdqg
-----END PGP SIGNATURE-----
Merge tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes
Pull "Rockchip dts32 fixes for 4.16" from Heiko Stübner:
Fix wrong dwmmc tuning clocks that may make probing HS cards fail to
probe and removal of special opps from the phycore boards that may
run the cpu outside the soc-vendor specs.
* tag 'v4.16-rockchip-dts32fixes-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Fix DWMMC clocks
ARM: dts: rockchip: Remove 1.8 GHz operation point from phycore som
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
-----BEGIN PGP SIGNATURE-----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=cN4I
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.16-rc cycle
This is mostly SoC related fixes for clocks, interconnect, and PM with few
board specifc dts related fixes:
- Fix quirk handling for ti-sysc to check all quirk flags instead of just
the first one
- Fix LogicPD boards for i2c1 muxing to avoid intermittent PMIC errors
- Fix debounce-interval use for omap5-uevm
- Fix debugfs_create_*() usage for omap1
- Fix sar_base initialization for HS omaps
- Fix omap3 prm wake interrupt for resume
- Fix kmemleak for omap_get_timer_dt()
- Enable optional clocks before main clock to prevent interconnect target
module from being stuck in transition
* tag 'omap-for-v4.16/fixes-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Fix checking of no-reset-on-init quirk
ARM: dts: LogicPD SOM-LV: Fix I2C1 pinmux
ARM: dts: LogicPD Torpedo: Fix I2C1 pinmux
ARM: dts: OMAP5: uevm: Fix "debounce-interval" property misspelling
ARM: OMAP1: clock: Fix debugfs_create_*() usage
ARM: OMAP2+: Fix sar_base inititalization for HS omaps
ARM: OMAP3: Fix prm wake interrupt for resume
ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt
ARM: OMAP2+: hwmod_core: enable optional clocks before main clock
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"Midas" is the codename for a family of smartphones released by Samsung
Mobile. It includes the Galaxy S3 (GT-I9300/I9305) and the Galaxy
Note 2 (GT-N7100/N7105). The boards largely have the same peripherals:
the main differences are touchscreen, display panel and cellular modem.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Midas boards share a lot with Trats2. Split the common parts
out of Trats2 into a common Midas DTSI and a common "Galaxy S3" DTS.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently, same stm32f746-pinctrl driver is used for stm32f746 and
stm32f769 MCU. As pin map is different between those 2 MCUs,
a stm32f769-pinctrl driver has been recently added.
This patch
-allows to use stm32f769-pinctrl driver for stm32f769 boards
-reworks stm32 devicetree files to fit with stm32f746 / stm32f769
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.
This error has propagated across the 32-bit DTs too, so fix those up.
Fixes: 187d7967a5 ("ARM: dts: rockchip: add the sdio/sdmmc node for rk3036")
Fixes: faea098e18 ("ARM: dts: rockchip: add core rk3036 dtsi")
Fixes: 9848ebeb95 ("ARM: dts: rockchip: add core rk3228 dtsi")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip recommends to run the CPU cores only with operations points of
1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default
values instead.
Fixes: 903d31e346 ("ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update the Droid 4 devicetree to properly describe the reset
GPIO. Also rename the node to touchscreen instead of tsp,
which seems to be commonly used for touchscreens.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the PDU001 board from EETS GmbH.
The board is built around the byteENGINE module AM335X from
bytes at work AG which in turn is built around a Sitara SoC
from TI.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds dts support for magnetometer on Nokia N9.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: fix missing bracket]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti) on
all gpio ports of stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds system config support for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti)
for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4412 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Soc nodes are used in other exynos DTS. Exynos4210 boards should use
them as well.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
