The chain structure and functions are widely used by the qed* modules,
both for configuration and datapath.
E.g., qede's Tx has one such chain and its Rx has two.
Currently, the strucutre's fields which are required for datapath
related functions [produce/consume] are intertwined with fields which
are required only for configuration purposes [init/destroy/etc.].
This patch re-arranges the chain structure so that all the fields which
are required for datapath usage could reside in a single cacheline instead
of the two which are required today.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver needs to maintain a structure per-each concurrent possible
open aggregation, but the structure storing that metadata is far from
being optimized - biggest waste in it is that there are 2 buffer metadata,
one for a replacement buffer when the aggregation begins and the other for
holding the first aggregation's buffer after it begins [as firmware might
still update it]. Those 2 can safely be united into a single metadata
structure.
struct qede_agg_info changes the following:
/* size: 120, cachelines: 2, members: 9 */
/* sum members: 114, holes: 1, sum holes: 4 */
/* padding: 2 */
/* paddings: 2, sum paddings: 8 */
/* last cacheline: 56 bytes */
-->
/* size: 48, cachelines: 1, members: 9 */
/* paddings: 1, sum paddings: 4 */
/* last cacheline: 48 bytes */
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory for netdev private data is allocated using kzalloc/vzalloc in
alloc_netdev_mqs, thus there is no need to zero the stats portion of it
again in the driver's probe function.
In any case, the size for the memset is wrong as the stats member is of
type rtnl_link_stats64, not net_device_stats.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...
Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.
Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.
Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces printk() with netdev_err() for macvtap device.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_fdb_append may return error, so add the proper check,
otherwise it will cause memory leak.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Changes in v2:
- Unnecessary to initialize rc to zero.
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF initialization and destroy resources.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF interrupt processing.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for VF mailbox setup.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for initializing softcommand, dispatch and
instructions queues for VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF device register access.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for configuring VF input/output queues.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for setting up VF configuration.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for cn23xx VF probe and registration.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for CN23xx VF registers.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Rasesh Mody <Rasesh.Mody@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom BCM7xxx internal PHYs can leverage the Broadcom PHY library
module PHY error counters helper functions, just implement the
appropriate PHY driver function calls to do so. We need to allocate some
storage space for our PHY statistics, and provide it to the Broadcom PHY
library, so do this in a specific probe function, and slightly wrap the
get_stats function call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom PHYs expose a number of PHY error counters: receive errors,
false carrier sense, SerDes BER count, local and remote receive errors.
Add support code to allow retrieving these error counters. Since the
Broadcom PHY library code is used by several drivers, make it possible
for them to specify the storage for the software copy of the statistics.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool's '-r' command. Restarting
N-WAY negotiation can be useful to activate newly changed EEE
settings etc.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to query and set Energy Efficient Ethernet parameters
via ethtool for applicable devices.
This patch doesn't activate full EEE support in cpsw driver, but it
enables reading and writing EEE advertising settings. This way one
can disable advertising EEE for certain speeds.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Rami Rosen <roszenrami@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Also remember to put the of-node reference on probe errors.
Fixes: 1bb6aa56bb ("net: davinci_emac: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 077742dac2 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet
QoS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on initialisation errors and on device
close after having disconnected the PHY.
Fixes: b4bc88a868 ("ravb: Add fixed-link support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on initialisation errors and on uninit.
Fixes: 0c72c50f6f ("net-next: mediatek: add fixed-phy support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 83895bedee ("net: mvneta: add support for fixed links")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: bb74d9a4a8 ("fs_enet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 407066f8f3 ("net: fec: Support phys probed from devicetree and
fixed-link")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Note that we're still leaking any fixed-link PHY registered in the
non-OF probe path.
Fixes: 9abf0c2b71 ("net: bcmgenet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 186534a3f8 ("net: systemport: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: c7dfe3abf4 ("net: ethernet: nb8800: support fixed-link DT
node")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 7cdbc6f74f ("altera tse: add support for fixed-links.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we change MTU or the number of channels on a netvsc device we get the
following logged:
hv_netvsc bf5edba8...: net device safe to remove
hv_netvsc: hv_netvsc channel opened successfully
hv_netvsc bf5edba8...: Send section size: 6144, Section count:2560
hv_netvsc bf5edba8...: Device MAC 00:15:5d:1e:91:12 link state up
This information is useful as debug at most.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We call bus->init() before allocating 'lag.mapping'. Change the order of
operations in removal path to reflect that.
This makes the error path of mlxsw_core_bus_device_register() symmetric
with mlxsw_core_bus_device_unregister().
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this rollback, the thermal zone is still registered during the
error path, whereas its private data is freed upon the destruction of
the underlying bus device due to the use of devm_kzalloc(). This results
in use after free.
Fix this by calling mlxsw_thermal_fini() from the appropriate place in
the error path.
Fixes: a50c1e3565 ("mlxsw: core: Implement thermal zone")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The shared buffer pools are containers whose size is used to calculate
the maximum usage for packets from / to a specific port / {port, PG/TC},
when dynamic threshold is employed.
While it's perfectly fine for the sum of the pools to exceed the maximum
size of the shared buffer, a single pool cannot.
Add a check when the pool size is set and forbid sizes larger than the
maximum size of the shared buffer.
Without the patch:
$ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype
dynamic
// No error is returned
With the patch:
$ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype
dynamic
devlink answers: Invalid argument
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to limit the size of shared buffer pools, so query
the maximum size from the device during init.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added switchib driver fails to link if MLXSW_PCI=m:
drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function^Cmlxsw_sib_module_exit':
switchib.c:(.exit.text+0x8): undefined reference to `mlxsw_pci_driver_unregister'
switchib.c:(.exit.text+0x10): undefined reference to `mlxsw_pci_driver_unregister'
drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function `mlxsw_sib_module_init':
switchib.c:(.init.text+0x28): undefined reference to `mlxsw_pci_driver_register'
switchib.c:(.init.text+0x38): undefined reference to `mlxsw_pci_driver_register'
switchib.c:(.init.text+0x48): undefined reference to `mlxsw_pci_driver_unregister'
The other two such sub-drivers have a dependency, so add the same one
here. In theory we could allow this driver if MLXSW_PCI is disabled,
but it's probably not worth it.
Fixes: d1ba526384 ("mlxsw: switchib: Introduce SwitchIB and SwitchIB silicon driver")
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device_release_driver(&phydev->mdio.dev) is called, it releases all
resources belonging to the PHY device. Hence the subsequent call to
phy_led_triggers_unregister() will access already freed memory when
unregistering the LEDs.
Move the call to phy_led_triggers_unregister() before the possible call
to device_release_driver() to fix this.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a hardware issue happened as described by inline comments, the register
write pattern looks like the following:
<write ~MACB_BIT(RE)>
+ wmb();
<write MACB_BIT(RE)>
There might be a memory barrier between these two write operations, so add wmb
to ensure an flip from 0 to 1 for NCR.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On macb only (not gem), when a RX queue corruption was detected from
macb_rx(), the RX queue was reset: during this process the RX ring
buffer descriptor was initialized by macb_init_rx_ring() but we forgot
to also set bp->rx_tail to 0.
Indeed, when processing the received frames, bp->rx_tail provides the
macb driver with the index in the RX ring buffer of the next buffer to
process. So when the whole ring buffer is reset we must also reset
bp->rx_tail so the driver is synchronized again with the hardware.
Since macb_init_rx_ring() is called from many locations, currently from
macb_rx() and macb_init_rings(), we'd rather add the "bp->rx_tail = 0;"
line inside macb_init_rx_ring() than add the very same line after each
call of this function.
Without this fix, the rx queue is not reset properly to recover from
queue corruption and connection drop may occur.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 9ba723b081 ("net: macb: remove BUG_ON() and reset the queue to handle RX errors")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix comments, add some new, and make debugfs output consistent.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an option to disable EEE advertisement in the generic PHY
by providing a mask of prohibited modes corresponding to the value found in
the MDIO_AN_EEE_ADV register.
On some platforms, PHY Low power idle seems to be causing issues, even
breaking the link some cases. The patch provides a convenient way for these
platforms to disable EEE advertisement and work around the issue.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac4 IP can synthesized with 1-8 number of tx queues.
On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled
by default. For these IPs, the bitfield TXQEN is R/W.
Always enable tx queue 0. The write will have no effect on IPs synthesized
with DWC_EQOS_NUM_TXQ == 1.
The driver does still not utilize more than one tx queue in the IP.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dependencies on the architectures that support these devices and
add compile test to ensure ongoing code build coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 stats are chaotic because a deferred work queue is responsible
to update them every 250 ms.
Even sampling stats every one second with "sar -n DEV 1" gives
variations like the following :
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:39:22 eth0 146877.00 3265554.00 9467.15 4828168.50
07:39:23 eth0 146587.00 3260329.00 9448.15 4820445.98
07:39:24 eth0 146894.00 3259989.00 9468.55 4819943.26
07:39:25 eth0 110368.00 2454497.00 7113.95 3629012.17 <<>>
07:39:26 eth0 146563.00 3257502.00 9447.25 4816266.23
07:39:27 eth0 145678.00 3258292.00 9389.79 4817414.39
07:39:28 eth0 145268.00 3253171.00 9363.85 4809852.46
07:39:29 eth0 146439.00 3262185.00 9438.97 4823172.48
07:39:30 eth0 146758.00 3264175.00 9459.94 4826124.13
07:39:31 eth0 146843.00 3256903.00 9465.44 4815381.97
Average: eth0 142827.50 3179259.70 9206.30 4700578.16
This patch allows rx/tx bytes/packets counters being folded at the
time we need stats.
We now can fetch stats every 1 ms if we want to check NIC behavior
on a small time window. It is also easier to detect anomalies.
lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65
07:42:50 eth0 142915.00 3177696.00 9212.06 4698270.42
07:42:51 eth0 143741.00 3200232.00 9265.15 4731593.02
07:42:52 eth0 142781.00 3171600.00 9202.92 4689260.16
07:42:53 eth0 143835.00 3192932.00 9271.80 4720761.39
07:42:54 eth0 141922.00 3165174.00 9147.64 4679759.21
07:42:55 eth0 142993.00 3207038.00 9216.78 4741653.05
07:42:56 eth0 141394.06 3154335.64 9113.85 4663731.73
07:42:57 eth0 141850.00 3161202.00 9144.48 4673866.07
07:42:58 eth0 143439.00 3180736.00 9246.05 4702755.35
07:42:59 eth0 143501.00 3210992.00 9249.99 4747501.84
Average: eth0 142835.66 3182165.93 9206.98 4704874.08
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5ffbe0a19 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mt7601u_mac_stop_hw should stop polling the rxq once it remains empty
but instead continues polling after the rxq status stays clear; bringing
down the interface takes about six seconds from this alone.
Speed up path by exiting rxq loop once status repeatedly polls empty.
Signed-off-by: Anthony Romano <anthony.romano@coreos.com>
Reviewed-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The scan results for scheduled scan as retrieved from the device
have changed. A field has been added which is not needed. However,
the appended info is. Luckily they are versioned so check that to
find out the location of the appended data.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can specify the interval for the scheduled scan. This
interval is found in scheduled scan plan. The driver supports only
one plan, which is legacy behaviour.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the .sched_scan_start() callback a condition was checked whether a
normal scan was ongoing. However, there is no need for this check as
it is ok to start the scheduled scan irrespective whether or not a
normal scan is ongoing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
User-space can provide list of channels in the schedule scan request.
This was ignored so all channels supported and allowed by the device
were used. This patch configures the device to use the channels as
listed in the request.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework .sched_scan_start() callback moving actual configuration of
the device in pno source file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmf_pno_config() function handles two configurations in
firmware. Split it and have caller sort out what is needed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For scheduled scan we initiate an escan in firmware to obtain more
info missing from the scheduled scan notification we get from firmware.
For upcoming functionality this is also required so make it a bit
more generic.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the number of parameters as the removed ones can be obtained
through struct brcmf_if parameter.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ssids list in the scheduled scan request were not properly taken
into account when configuring in firmware. The hidden bit was set for
any ssid resulting in active scanning for all. Only set it for ssids
that are in the ssids list.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introducing new source file for pno related functionality. Moving
existing pno functions.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This chip was already supported, but seems a device came up giving
a different chip identifier. So adding that effectively mapping to
the same firmware file as for 43340 chip.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rev6 of pcie host dongle interface protocol, host needs to maximum
supported ring number from dongle shared memory and set up ring buffer
and ring indices offset accordingly.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell Wifi PCIe modules don't always behave nicely for PCIe power
management when their firmware hasn't been loaded, particularly after
suspending the PCIe link one or more times. When this happens, we might
end up spinning forever in this status-polling tight loop. Let's make
this less tight by adding a timeout and by sleeping a bit in between
reads, as we do with the other similar loops.
This prevents us from hogging a CPU even in such pathological cases, and
allows the FW initialization to just fail gracefully instead.
I chose the same polling parameters as the earlier loop in this
function, and empirically, I found that this loop never makes it more
than about 12 cycles in a sane FW init sequence. I had no official
information on the actual intended latency for this portion of the
download.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_usb_probe() defines and sets bcd_usb but does not use it,
Compiling with W=1 gives the following warning, fix it.
mwifiex/usb.c: In function ‘mwifiex_usb_probe’:
mwifiex/usb.c:383:41: warning: variable ‘bcd_usb’ set but not used [-Wunused-but-set-variable]
The unused variable seems to be present since 4daffe3543 which introduced
mwifiex_usb_probe().
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 92263a841b introduced mwifiex_deaggr_sdio_pkt which initializes
variable pkt_type but does not use it. Compiling with W=1 gives the following
warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_deaggr_sdio_pkt’:
mwifiex/sdio.c:1198:6: warning: variable ‘pkt_type’ set but not used [-Wunused-but-set-variable]
Fixes: 92263a841b ("mwifiex: add SDIO rx single port aggregation")
Cc: Zhaoyang Liu <liuzy@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_sdio_resume() intializes pm_flag, just like
mwifiex_sdio_suspend(), but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sdio.c: In function ‘mwifiex_sdio_resume’:
mwifiex/sdio.c:234:16: warning: variable ‘pm_flag’ set but not used [-Wunused-but-set-variable]
sdio_get_host_pm_caps() is just an acessor, so the call to it is safe
to remove. The unused variable seems to be present since
5e6e3a92b9 which introduced mwifiex_sdio_resume().
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 3935ccc14d introduced mwifiex_tm_cmd() which initializes
struct mwifiex_adapter* adapter, but doesn't use it.
Compiling with W=1 gives the following warning, fix it.
mwifiex/cfg80211.c: In function ‘mwifiex_tm_cmd’:
mwifiex/cfg80211.c:3973:26: warning: variable ‘adapter’ set but not used [-Wunused-but-set-variable]
Fixes: 3935ccc14d ("mwifiex: add cfg80211 testmode support")
Cc: Xinming Hu <huxm@marvell.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 429d90d221 introduced mwifiex_cmd_tdls_oper() which initializes
struct mwifiex_sta_node* sta_ptr, but does not use it. Compiling with W=1 gives
the following warning, fix it.
mwifiex/sta_cmd.c: In function ‘mwifiex_cmd_tdls_oper’:
mwifiex/sta_cmd.c:1732:27: warning: variable ‘sta_ptr’ set but not used [-Wunused-but-set-variable]
Fixes: 429d90d221 ("mwifiex: add cfg80211 tdls_oper handler support")
Cc: Avinash Patil <patila@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b5413e6b22 removed all uses of chan_num in mwifiex_config_scan().
Compiling mwifiex with W=1 gives the following warning, fix it.
mwifiex/scan.c: In function ‘mwifiex_config_scan’:
mwifiex/scan.c:830:6: warning: variable ‘chan_num’ set but not used [-Wunused-but-set-variable]
Fixes: b5413e6b22 ("mwifiex: increase the number of nodes in command pool")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit bec568ff51 removed the last remaining usage of struct
mwifiex_private* priv in mwifiex_fw_dpc(), by removing the call to
mwifiex_del_virtual_intf().
Compiling mwifiex/ with W=1 gives the following warning, fix it.
mwifiex/main.c: In function ‘mwifiex_fw_dpc’:
mwifiex/main.c:520:26: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
Fixes: bec568ff51 ("mwifiex: failure path handling in mwifiex_add_virtual_intf()")
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It shold reserved sizeof(ipv6hdr) for geneve in ipv6 tunnel.
Fixes: c3ef5aa5e5 ('geneve: Merge ipv4 and ipv6 geneve_build_skb()')
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In procedure mlx4_flow_steer_promisc_add(), several fields
were left uninitialized in the rule structure.
Correctly initialize these fields.
Fixes: 592e49dda8 ("net/mlx4: Implement promiscuous mode with device managed flow-steering")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user can now override the automatic driver decision using the
rx_cqe_compress flag, which is the preference for CQE compression.
The flag is initialized with the automatic driver decision.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pflags is a configuration parameter for the netdev, naturally it belongs
to priv->params.
Also introduce MLX5E_GET_PFLAG
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the self diagnostic tests to support loopback test.
The loopback test doesn't require the offline flag, it will use the
generic dev_queue_xmit and a dedicated packet_type to capture and verify
mlx5e selftest loopback packets.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The self diagnostics test implementaion include the following features:
1. Link Test: Check that link is in up state.
2. Speed Test: Check that link was negotiated correctly.
3. Health Test: Check the device health.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setdcbx interface to set the DCBX mode to firmware or os.
If setdcbx is called with mode value of zero, the DCBX mode
is set to firmware.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DBCX by default is controlled by firmware where dcbx capability bit
is set. In this mode, firmware is responsible for reading/sending the
TLV packets from/to the remote partner.
This patch sets up the infrastructure to move between HOST/FW DCBX
control mode.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add set/query commands for DCBX_PARAM register
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue description:
Current implementation saves the ETS settings from user in
a temporal soft copy and returns this settings when user
queries the ETS settings.
With the new DCBX firmware, the ETS settings can be changed
by firmware when the DCBX is in firmware controlled mode. Therefore,
user will obtain wrong values from the temporal soft copy.
Solution:
1. Read the ETS settings directly from firmware.
2. For tc_tsa:
a. Initialize tc_tsa to vendor IEEE_8021QAZ_TSA_VENDOR at netdev
creation.
b. When reading ETS setting from FW, if the traffic class bandwidth
is less than 100, set tc_tsa to IEEE_8021QAZ_TSA_ETS. This
implementation solves the scenarios when the DCBX is in FW control
and willing bit is on which means the ETS setting is dictated
by remote switch.
Also check ETS capability where needed.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCBX CEE API interface for ConnectX-4. Configurations are stored in
a temporary structure and are applied to the card's firmware when
the CEE's setall callback function is called.
Note:
priority group in CEE is equivalent to traffic class in ConnectX-4
hardware spec.
bw allocation per priority in CEE is not supported because ConnectX-4
only supports bw allocation per traffic class.
user priority in CEE does not have an equivalent term in ConnectX-4.
Therefore, user priority to priority mapping in CEE is not supported.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure firmware supports qos before exposing the DCB API.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use single queue even if multiqueue is enabled and let admin to
enable it through ethtool later. This is used to avoid possible
regression (small packet TCP stream transmission). But looks like an
overkill since:
- single queue user can disable multiqueue when launching qemu
- brings extra troubles for the management since it needs extra admin
tool in guest to enable multiqueue
- multiqueue performs much better than single queue in most of the
cases
So this patch enables multiqueue by default: if #queues is less than or
equal to #vcpu, enable as much as queue pairs; if #queues is greater
than #vcpu, enable #vcpu queue pairs.
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Marko Myllynen <myllynen@redhat.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
drivers/net/ethernet/amd/xgbe/xgbe-main.c:835:12: warning: ‘xgbe_suspend’ defined
but not used [-Wunused-function]
drivers/net/ethernet/amd/xgbe/xgbe-main.c:855:12: warning: ‘xgbe_resume’ defined
but not used [-Wunused-function]
I see it during randconfig builds here.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The old logic always enabled the TX-delay when the phy-mode was set to
PHY_INTERFACE_MODE_RGMII. There are dedicated phy-modes which tell the
PHY driver to enable the RX and/or TX delays:
- PHY_INTERFACE_MODE_RGMII should disable the RX and TX delay in the
PHY (if required, the MAC should add the delays in this case)
- PHY_INTERFACE_MODE_RGMII_ID should enable RX and TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_TXID should enable the TX delay in the PHY
- PHY_INTERFACE_MODE_RGMII_RXID should enable the RX delay in the PHY
(currently not supported by RTL8211F)
With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID
and PHY_INTERFACE_MODE_RGMII_TXID.
Additionally we now explicity disable the TX-delay, which seems to be
enabled automatically after a hard-reset of the PHY (by triggering it's
reset pin) to get a consistent state (as defined by the phy-mode).
This fixes a compatibility problem with some SoCs where the TX-delay was
also added by the MAC. With the TX-delay being applied twice the TX
clock was off and TX traffic was broken or very slow (<10Mbit/s) on
1000Mbit/s links.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the dev_info call that attempts to show the rate used before it is set.
Signed-off-by: Barry Day <briselec@gmail.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Barry Day <briselec@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since long already bpf_func is not only about struct sk_buff * as
input anymore. Make it generic as void *, so that callers don't
need to cast for it each time they call BPF_PROG_RUN().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use ->heap_buf after commit 46d1efd852 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The macvtap_newlink registers the netdev rx_handler firstly, but it
does not unregister the handler if macvlan_common_newlink failed.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() during
probe on probe errors and on driver unbind.
Also drop the of_node reference taken by of_parse_phandle() in the same
path.
Fixes: b9b17debc6 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() when
looking up a fixed-link phydev during probe.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() during
initialisation when later freeing the struct fman_mac.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_phy_find_device() when
initialising MOCA PHYs.
Fixes: 6ac9de5f65 ("net: bcmgenet: Register link_update callback for
all MoCA PHYs")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
irda_get_mtt() returns a hardcoded '10000' in some cases,
and with gcc-7, we get a build error because this triggers a
compile-time check in udelay():
drivers/net/irda/w83977af_ir.o: In function `w83977af_hard_xmit':
w83977af_ir.c:(.text.w83977af_hard_xmit+0x14c): undefined reference to `__bad_udelay'
Older compilers did not run into this because they either did not
completely inline the irda_get_mtt() or did not consider the
10000 value a constant expression.
The code has been wrong since the start of git history.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ipvlan_link_new fails and creates one ipvlan port, it does not
destroy the ipvlan port created. It causes mem leak and the physical
device contains invalid ipvlan data.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on commit d8d2635419 ("ptp: Introduce a high
resolution frequency adjustment method.")
The gianfar devices offer a frequency resolution of about 0.46 ppb
(depends on actual value of tmr_add, for the calculation assumed
0x80000000). This patch lets users of the device benefit from the increased
frequency resolution when tuning the clock. Thanks to the rounding the
maximum error between the requested frequency and the applied frequency
will then be about 0.23 ppb.
Tested on a v3.3.8 kernel on a real gianfar device. Verified compilation
on net-next (currently at v4.9-rc5).
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per RX ring packets/bytes counters are not protected by global
priv->stats_lock.
Better not confuse the reader, and use READ_ONCE() to show we read
these counters without surrounding synchronization.
Interrupt moderation is best effort, and we do not really care of
ultra precise counters.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure policers and connect them to trap groups.
While many trap groups share policer's configuration they don't share
the actual policer because each trap group represents a different
flow / protocol and we don't want one of them to be able to exceed its
rate on behalf of another.
For example, if STP and LLDP gets to send 128 packets/sec each, if we
put them in one 256 packets/sec policer, one can send 200 packets while
the other only 50.
Note that IP2ME covers lots of flows, so it's limit is set to match the
cpu ability to handle data.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPCR register is used to create and control policers.
A policer can discard or change the color of packets that are
trapped by a specific trap.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new resource to resources query: max cpu policers which tells us how
many policers can be used to limit the data rate to the cpu port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups can be used to control traps priority, both in terms of
which trap "wins" if a packet matches two traps (priority) and in terms
of packets from which trap group will be scheduled to the cpu first (tc).
They can also be used to set rate limiters (policers) on them (will be
added in the next patches).
Currently, we support two trap groups. In Spectrum we want a better
resolution, so every protocol / flow will have a different trap group,
so we can control its parameters separately. Once the policers will be
implemented, it will also allow us limit the rate of each protocol by
itself.
This patch change the trap group list to include:
* the emad trap group, which is shared for all the devices.
* Switchx2's trap groups, which are a copy of the current trap groups.
* Spectrum's new trap groups, in order to match the above guidelines.
(Switchib is using only the emad trap group, so it require no changes).
This patch also includes new configuration for Spectrum's trap groups,
with primary priority order within them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trap for BGP protocol that was previously trapped by the generic trap
for IP2ME. This trap will allow us to have better control (over priority
and rate) of the traffic.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trap groups have many options which we currently set to default values.
In the next patches we will use many of them with non-default values.
Some of these options have no default value, so this patch sets them as
params for the trap group set function. Others almost always use the same
values, so the set function will use this default values. In the rare cases
when they will need to be with other values, these values can be set
directly (using the macros for fields in registers).
Parameters without default value:
TC - the traffic class for packets that hit this trap group.
(old default is the max tc)
priority - if one packet hits multiple trap groups, the group with the
higher priority will "catch" it. (old default is 0)
policer - limit rate policer (old default is disabled)
Default parameters:
swid - switch id, relevant for the emad trap only, ignored on Spectrum.
(new default is 0)
rdq - CPU receive descriptor queue (new default is identical to trap
group id)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the max number of trap groups to resource query.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the emad trap init was done in the core. In the future we will
want to add some changes to the traps groups, according to device type.
This commit create a driver function to create the trap group for the
emad, so later it can be changed by devices. It also changes the emad
registration to use the new generic functions.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we set the trap group to pre-determined option, based on whether
it is an rx or event trap.
This commit adds a possibility to chose the trap group, so it can be set
to different values in the following patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change trap setting function so instead of determining the trap group by
trap id, it gets it as a parameter (so later we can have different trap
groups for Spectrum and Switchx2).
Add "is_ctrl" parameter to the trap setting function. It control whether
the trapped packets wait in a designated control buffer or in their
default one. This parameter is ignored by Switchx2 and Switchib.
Add these parameters to the traps array in Spectrum, Switchx2 and
Switchib.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the event handling in Switchib to be comptible with Spectrum and
Switchx2.
Use the generic listener struct for the events. Init and fini them by loop
(and not by calling each event by its name).
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the events to use the generic listener struct.
Merge the event list into the trap list, so the same functions will
handle both.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a macro for creating the generic listener struct for events,
similar to the one for rx traps.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorganize the traps to use the new generic listener struct and
functions. Use macros to shorten the traps list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the old rx listener struct definitions by the generic ones.
Use the new generic registering / unregistering functions for them.
Add some macros to organize the trap list.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum, there is a macro to arrange the traps list.
This macro is useful for everyone who is using rx traps.
Create a similar macro in core.h for creating the generic listener struct
for rx traps.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have 2 types of HW traps to handle, rx traps and events.
The registration workflow for both is very similar. So it only make
sense to create one function to handle both.
This patch creates a struct to hold the data for both cases. It also
creates a registration and an un-registration functions that get this
generic struct as input.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 99724c18fc ("mlxsw: spectrum: Introduce support for
router interfaces") we no longer rely on flooding traffic to the CPU in
order to trap packets intended for the host itself. Therefore, the FDB
MC trap can be removed.
Remove traps for protocols that are not supported yet.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-7 detects a short memset in mvpp2, introduced in the original
merge of the driver:
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init':
drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size]
The result seems to be that we write uninitialized data into the
flow table registers, although we did not get any warning about
that uninitialized data usage.
Using sizeof() lets us initialize then entire array instead.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header delay.h from mlx5/core/main.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Matan Barak <matanb@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header delay.h from adf7242.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate header seq_file.h from ibmvnic.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set "tgec->cfg" to NULL before passing it to kfree(). There is no
need to set it to NULL at all. Let's just delete it.
Fixes: 57ba4c9b56 ("fsl/fman: Add FMan MAC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We verified that MLX5_FLOW_CONTEXT_ACTION_COUNT was set on the first
line of the function so we don't need to check again here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable pause frames on both Rx and Tx side, configure pause
interval e.t.c. Also support for enable/disable pause frames
on Rx/Tx via ethtool has been added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables moving average calculation of Rx pkt's resources
and configures RED and backpressure levels for both CQ and RBDR.
Also initialize SQ's CQ_LIMIT properly.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 80xx only one lane of DLM0 and DLM1 (of BGX0) can be used
, so even though lmac count may be 2 but LMAC1 should use
serdes lane of DLM1. Since it's not possible to distinguish
80xx from 81xx as PCI devid are same, this patch adds this
config support by replying on what firmware configures the
lmacs with.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy_init_hw() fails at phy_attach_direct();
- phy_detach() calls phy_led_triggers_unregister() without
previous call of phy_led_triggers_register().
- still call phy_led_triggers_register() and cause memory leak.
Fixes: 2e0bc452f4 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver advertises it supports IFF_UNICAST_FLT. However, it
actually does not. The hardware probably does support it, but there is
no code to configure the filter. As a quick and simple fix, remove the
flag. This will cause the core to fall back to promiscuous mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: b50b72de2f ("net: mvneta: enable features before registering the driver")
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop duplicate headers types.h and delay.h from dwc_eth_qos.c.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if txq_info->uldtxq cannot be allocated then
txq_info->txq is being kfree'd (which is redundant because it
is NULL) instead of txq_info. Fix this by instead kfree'ing
txq_info.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I get the following UBSAN warning during boot on my laptop:
================================================================================
UBSAN: Undefined behaviour in drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:280:21
index 32 is out of range for type 's16 [32]'
CPU: 0 PID: 879 Comm: NetworkManager Not tainted 4.9.0-rc4 #28
Hardware name: LENOVO Lenovo IdeaPad N581/INVALID, BIOS 5ECN96WW(V9.01) 03/14/2013
ffff8800b74a6478 ffffffff828e59d2 0000000041b58ab3 ffffffff8398330c
ffffffff828e5920 ffff8800b74a64a0 ffff8800b74a6450 0000000000000020
1ffffffff845848c ffffed0016e94bf1 ffffffffc22c2460 000000006b9c0514
Call Trace:
[<ffffffff828e59d2>] dump_stack+0xb2/0x110
[<ffffffff828e5920>] ? _atomic_dec_and_lock+0x150/0x150
[<ffffffff82968c9d>] ubsan_epilogue+0xd/0x4e
[<ffffffff82969875>] __ubsan_handle_out_of_bounds+0xfa/0x13e
[<ffffffff8296977b>] ? __ubsan_handle_shift_out_of_bounds+0x241/0x241
[<ffffffffc0d48379>] ? bcma_host_pci_read16+0x59/0xa0 [bcma]
[<ffffffffc0d48388>] ? bcma_host_pci_read16+0x68/0xa0 [bcma]
[<ffffffffc212ad78>] ? read_phy_reg+0xe8/0x180 [brcmsmac]
[<ffffffffc2184714>] qm_log10+0x2e4/0x350 [brcmsmac]
[<ffffffffc2142eb8>] wlc_phy_init_lcnphy+0x538/0x1f20 [brcmsmac]
[<ffffffffc2142980>] ? wlc_lcnphy_periodic_cal+0x5c0/0x5c0 [brcmsmac]
[<ffffffffc1ba0c93>] ? ieee80211_open+0xb3/0x110 [mac80211]
[<ffffffff82f73a02>] ? sk_busy_loop+0x1e2/0x840
[<ffffffff82f7a6ce>] ? __dev_change_flags+0xae/0x220
...
The report is valid: doing the math in this function, with an input value
N=63 the variable s16tableIndex gets a value of 31. This value is used as
an index in the array log_table with 32 entries. But the next line is:
s16errorApproximation = (s16) qm_mulu16(u16offset,
(u16) (log_table[s16tableIndex + 1] -
log_table[s16tableIndex]));
With s16tableIndex + 1 we are trying an out-of-bounds access to the array.
The log_table array provides log2 values in q.15 format and the above
statement tries an error approximation with the next value. To fix this
issue add the next value to the array and update the comment accordingly.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will read fw_cap_info filled by firmware to check whether to
skip ADHOC related commands or not. Also, IBSS_COALESCING_STATUS
command has been moved from init path to adhoc network creation
path.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_8192e.c:1559:6: warning:
symbol 'rtl8192eu_power_off' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to obtain retry count for a given rate we need to pass the
full struct ieee80211_tx_info to the function setting the rate in he
TX descriptor.
This uncovered a huge bug where the old code would use struct
ieee80211_rate.flags to test for rate parameters, which is always
zero, instead of the flags value from struct ieee80211_tx_rate.
Time to find a brown paper bag :(
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the mac80211 provided rate for RTS rather than the hard coded
24Mbps as suggested by the vendor drivers.
Reported-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu suffered from two issues when reloading the driver.
The same problems as with the 8723bu where REG_RX_WAIT_CCA bits 22 and
23 didn't get set in rtl8192e_enable_rf().
In addition it also seems prone to issues when setting REG_RF_CTRL to
0 intead of just disabling the RF_ENABLE bit. Similar to what was
causing issues with the 8188eu.
With this patch I can successfully reload the driver and reassociate
to an APi with an 8192eu dongle.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The generic disable_rf() function clears bits 22 and 23 in
REG_RX_WAIT_CCA, however we did not re-enable them again in
rtl8723b_enable_rf()
This resolves the problem for me with 8723bu devices not working again
after reloading the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The full RX descriptor is converted so converting tsfl again would
return it to it's original endian value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A device running without RX package aggregation could return more data
in the USB packet than the actual network packet. In this case the
could would clone the skb but then determine that that there was no
packet to handle and exit without freeing the cloned skb first.
This has so far only been observed with 8188eu devices, but could
affect others.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have a race where the wakeup IRQ might be in flight while we're
calling mwifiex_disable_wake() from resume(). This can leave us
disabling the IRQ twice.
Let's disable the IRQ and enable it in case if we have double-disabled
it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't want to leave the wake IRQ enabled.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit power level in a channel is determined based on the dfs region.
To support regulatory rules dfs region should be configured to device during
set channel request. Also antenna gain values are taken from the mac80211
channel parameters instead of fixed values.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RSI 9113 device supports single antenna for tx and rx. Support for using
external is added. This can be configured from user space using iw.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TX power can be configured from iwconfig, iw or from mac80211 when
regulatory changes are done. Hence support for configuring tx power
to device is added using the RADIO_PARAMS_UPDATE command frame.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Filtering rx frames after connection in station mode avoids the
overhead of processing un-necessary frames. Hence rx filter frame
is added which can be configured to device at suitable times.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After commit 1576d98605 ("tun: switch to use skb array for tx"),
sk_receive_queue was not used any more. So remove the uncessary
sk_receive_queue length check during xmit.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY drivers should be able to rely on the caller of {get,set}_tunable to
have acquired the PHY device mutex, in order to both serialize against
concurrent calls of these functions, but also against PHY state machine
changes. All ethtool PHY-level functions do this, except
{get,set}_tunable, so we make them consistent here as well.
We need to update the Microsemi PHY driver in the same commit to avoid
introducing either deadlocks, or lack of proper locking.
Fixes: 968ad9da7e ("ethtool: Implements ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE")
Fixes: 310d9ad57a ("net: phy: Add downshift get/set support in Microsemi PHYs driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A flow should be offloaded only if the matches are
allowed according to min inline mode.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement devlink show and set of HW inline-mode.
The supported modes: none, link, network, transport.
We currently support one mode for all vports so set is done on all vports.
When eswitch is first initialized the inline-mode is queried from the FW.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also move the inline capablities enum to a shared header vport.h
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflect the administative link changes done on the VF representor to the
VF e-switch vport. This means that doing ip link set down/up commands on
the VF rep will modify the e-switch vport state which in turn will make
proper VF drivers to set their carrier accordingly.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switchdev driver net-device port statistics should follow the model introduced
in commit a5ea31f573 'Merge branch net-offloaded-stats'.
For VF reps we return the SRIOV eswitch vport stats as the usual ones and SW stats
if asked. For the PF, if we're in the switchdev mode, we return the uplink stats
and SW stats if asked, otherwise as before. The uplink stats are implemented using
the PPCNT 802_3 counters which are already being read/cached by the driver.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.
Fixes: 450b05c15f ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When busy polling while a link is down (during a link-flap test), TX
timeouts were observed as well as the following messages in the ring
buffer:
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free tx failed. rc:-1
bnxt_en 0008:01:00.2 enP8p1s0f2d2: Resp cmpl intr err msg: 0x51
bnxt_en 0008:01:00.2 enP8p1s0f2d2: hwrm_ring_free rx failed. rc:-1
These were resolved by checking for link status and returning if link
was not up.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Rob Miller <rob.miller@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure mlx4_en_free_resources is called under the netdev state lock.
This is needed since RCU dereference of XDP prog should be protected.
Fixes: 326fe02d1e ("net/mlx4_en: protect ring->xdp_prog with rcu_read_lock")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Sagi Grimberg <sagi@grimberg.me>
CC: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Knowing that:
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_VXLAN (0x1UL << 0)
#define TUNNEL_DST_PORT_FREE_REQ_TUNNEL_TYPE_GENEVE (0x5UL << 0)
and that 'bnxt_hwrm_tunnel_dst_port_alloc()' is only called with one of
these 2 constants, the TUNNEL_DST_PORT_ALLOC_REQ_TUNNEL_TYPE_GENEVE can not
trigger.
Replace the bit test that overlap by an equality test, just as in
'bnxt_hwrm_tunnel_dst_port_free()' above.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_set_promiscuity failed in macvlan_open, it always invokes
dev_set_allmulti without checking if necessary.
Now check the IFF_ALLMULTI flag firstly before rollback the multicast
setting in the error handler.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix setting of SUPPORTED_FIBRE bit as it was not present in features
of KSZ8041.
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to receive other BSS entries in mesh mode, Monitor vdev
is created whenever filter flag is set with OTHER_BSS. Recently
it is root caused that setting promisc filter for Mesh interface
is causing performance and stability issues. To fix this issue,
firmware will configure appropriate rxfilters by default for mesh
vdev during vdev creation. This change fixes monitor vdev creation
based on firmware IE
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per STA tx bitrate info is filled from peer stats.
Export per sta txrate info to cfg80211/nl80211
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Per peer tx stats are part of 'HTT_10_4_T2H_MSG_TYPE_PEER_STATS'
event, Firmware sends one HTT event for every four PPDUs.
HTT payload has success pkts/bytes, failed pkts/bytes, retry
pkts/bytes and rate info per ppdu.
Peer stats are enabled through 'WMI_SERVICE_PEER_STATS',
which are nowadays enabled by default.
Parse peer stats and update the tx rate information per STA.
tx rate, Peer stats are tested on QCA4019 with Firmware version
10.4-3.2.1-00028.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sending frames in CCK rates on HT can cause performance problems.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use RTS/CTS protection for TXOP on all rates modes as default and
disable CCK rates (this cause performance problems).
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.
On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialize AUTO_RSP_CFG register to similar value as vendor driver does.
Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should not reset USB_DMA_CFG on rt2800usb_init_registers() as this
function is called indirectly from rt2800_enable_radio(). If we
do so, we wipe out USB_DMA_CFG settings from rt2800usb_enable_radio().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware doesn't update beacon/Probe Response vendor IEs correctly when
bss is down, so we move brcmf_config_ap_mgmt_ie after BSS up. And host
driver should clear IEs when AP stopped so that the IEs in host side will
be synced with in firmware side.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB"
will not cover the case when it is configured as module. This will
omit the entire if-block which does cleanup of URBs and cancellation
of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for setting retry limit for short frames,
using NL80211_CMD_SET_WIPHY with the attribute
NL80211_ATTR_WIPHY_RETRY_SHORT.
Update wiphy->retry_short from the FW default when interface
is brought up.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Align to latest version of the auto generated wmi file
describing the interface with FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Implement cfg80211 abort_scan op to allow the upper layer to
abort an ongoing scan request.
In addition, notify wil6210 device on scan abort request instead
of just ignoring the scan response.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When FW crashes with no_fw_recovery option, driver
waits for manual recovery with wil->mutex held, this
can easily create deadlocks.
Fix the problem by moving the wait outside the lock.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
New power management wmi commands provide the ability to change
the device power save profile (enable / disable power save).
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver calls to netif_tx_stop_all_queues/netif_tx_wake_all_queues are
inconsistent. In several cases, driver can get to a situation where net
queues are stopped forever and data cannot be sent.
The fix is to stop net queues if there is at least one vring which is
"full" and to wake net queues if all vrings are not "full".
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit b2d70d4944 ("ath9k: make GPIO API to support both of WMAC and
SOC") refactored ath9k_hw_gpio_get() to support both WMAC and SOC GPIOs,
changing the return on success from 1 to BIT(gpio). This broke some callers
like ath_is_rfkill_set(). This doesn't fix any known bug in mainline at the
moment, but should be fixed anyway.
Instead of fixing all callers, change ath9k_hw_gpio_get() back to only
return 0 or 1.
Fixes: b2d70d4944 ("ath9k: make GPIO API to support both of WMAC and SOC")
Cc: <stable@vger.kernel.org> # v4.7+
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
[kvalo@qca.qualcomm.com: mention that doesn't fix any known bug]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Command structure and event flow doesn't seem to
be any different compared to existing
implementation for other firmware branches.
This patch effectively adds in-driver support for
spectral scanning on QCA61x4 and QCA9377.
Tested QCA9377 w/ WLAN.TF.1.0-00267-1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Neither of these did the right thing:
- get_tsf just returned 0
- set_tsf assumed a simple offset was applied against
get_tsf(), which works, except in the case of
calculating TSF from rx_mactime (actual TSF).
Just remove them for now. We can reimplement set_tsf in
terms of TSF increment/decrement in the future if get_tsf
is ever supported by FW.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
