A lot of stuff in spitz/akita/etc. depends on corgi_ssp to be initialised
early. However corgi_ssp initialisation fails, because at that time pxa*-ssp
devices don't have drivers. Move ssp earlier in the makefile so they are
registered before corgi-ssp.
Also move sleep/suspend and cpu-freq to more logical places
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up Orion's addr-map.c a bit after all peripheral
window programming code has been moved out into the relevant drivers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Pass the Orion TCLK tick rate into the ethernet driver.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make the Orion 5x platform code use the mbus window handling code
that's in the mv643xx_eth driver, instead of programming the GigE
block's mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
net: Added ASSERT_RTNL() to dev_open() and dev_close().
can: Fix can_send() handling on dev_queue_xmit() failures
netns: Fix arbitrary net_device-s corruptions on net_ns stop.
netfilter: Kconfig: default DCCP/SCTP conntrack support to the protocol config values
netfilter: nf_conntrack_sip: restrict RTP expect flushing on error to last request
macvlan: Fix memleak on device removal/crash on module removal
net/ipv4: correct RFC 1122 section reference in comment
tcp FRTO: SACK variant is errorneously used with NewReno
e1000e: don't return half-read eeprom on error
ucc_geth: Don't use RX clock as TX clock.
cxgb3: Use CAP_SYS_RAWIO for firmware
pcnet32: delete non NAPI code from driver.
fs_enet: Fix a memory leak in fs_enet_mdio_probe
[netdrvr] eexpress: IPv6 fails - multicast problems
3c59x: use netstats in net_device structure
3c980-TX needs EXTRA_PREAMBLE
fix warning in drivers/net/appletalk/cops.c
e1000e: Add support for BM PHYs on ICH9
uli526x: fix endianness issues in the setup frame
uli526x: initialize the hardware prior to requesting interrupts
...
This reverts commit 9f8daccaa0, which was
reported to break X startup (xf86-video-ati-6.8.0). See
http://bugs.freedesktop.org/show_bug.cgi?id=15523
for details.
Reported-by: Laurence Withers <l@lwithers.me.uk>
Cc: Gary Hade <garyhade@us.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: "Jun'ichi Nomura" <j-nomura@ce.jp.nec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix allmodconfig build bug introduced in latest -git by commit
7c91f0624a ("V4L/DVB(7767): Move tuners to common/tuners"):
LD kernel/built-in.o
LD drivers/built-in.o
ld: drivers/media/built-in.o: No such file: No such file or directory
which happens if all media drivers are modular:
http://redhat.com/~mingo/misc/config-Wed_Apr_30_09_24_48_CEST_2008.bad
In that case there's no obj-y rule connecting all the built-in.o files and
the link tree breaks.
The fix is to add a guaranteed obj-y rule for the core vmlinux to build.
(which results in an empty object file if all media drivers are modular)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Wait for async events to finish before destroying QP
IB/ipath: Fix SDMA error recovery in absence of link status change
IB/ipath: Need to always request and handle PIO avail interrupts
IB/ipath: Fix count of packets received by kernel
IB/ipath: Return the correct opcode for RDMA WRITE with immediate
IB/ipath: Fix bug that can leave sends disabled after freeze recovery
IB/ipath: Only increment SSN if WQE is put on send queue
IB/ipath: Only warn about prototype chip during init
RDMA/cxgb3: Fix severe limit on userspace memory registration size
RDMA/cxgb3: Don't add PBL memory to gen_pool in chunks
Make cpu_relax() invoke barrier() to be the same as other arches.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Revert "relay: fix splice problem"
docbook: fix bio missing parameter
block: use unitialized_var() in bio_alloc_bioset()
block: avoid duplicate calls to get_part() in disk stat code
cfq-iosched: make io priorities inherit CPU scheduling class as well as nice
block: optimize generic_unplug_device()
block: get rid of likely/unlikely predictions in merge logic
vfs: splice remove_suid() cleanup
cfq-iosched: fix RCU race in the cfq io_context destructor handling
block: adjust tagging function queue bit locking
block: sysfs store function needs to grab queue_lock and use queue_flag_*()
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-udf-2.6:
udf: Fix memory corruption when fs mounted with noadinicb option
udf: Make udf exportable
udf: fs/udf/partition.c:udf_get_pblock() mustn't be inline
alpha:
drivers/scsi/dpt_i2o.c:1997: error: implicit declaration of function 'adpt_alpha_info'
drivers/scsi/dpt_i2o.c: At top level:
drivers/scsi/dpt_i2o.c:2032: warning: conflicting types for 'adpt_alpha_info'
drivers/scsi/dpt_i2o.c:2032: error: static declaration of 'adpt_alpha_info' follows non-static declaration
drivers/scsi/dpt_i2o.c:1997: error: previous implicit declaration of 'adpt_alpha_info' was here
Due to a copy-n-paste error in drivers/scsi/dpti.h.
Fix that up and remove some of the many daft static-declarations-in-a-header
which this driver enjoys.
Cc: Miquel van Smoorenburg <miquels@cistron.nl>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to a merge conflict, the sched_relax_domain_level control file was marked
as being handled by cpuset_read/write_u64, but the code to handle it was
actually in cpuset_common_file_read/write.
Since the value being written/read is in fact a signed integer, it should be
treated as such; this patch adds cpuset_read/write_s64 functions, and uses
them to handle the sched_relax_domain_level file.
With this patch, the sched_relax_domain_level can be read and written, and the
correct contents seen/updated.
Signed-off-by: Paul Menage <menage@google.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
any_slab_objects() does an atomic_read on an atomic_long_t, this
fixes it to use atomic_long_read instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remember to close the files if copy_to_user() failed.
Spotted by dm.n9107@gmail.com.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: DM <dm.n9107@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For e.g. proper TTY canonical support, IUTF8 termios flag has to be set as
appropriate. Linux used to not care about setting that flag for VT TTYs.
This patch fixes that by activating it according to the current mode of the
VT, and sets the default value according to the vt.default_utf8 parameter.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Willy Tarreau <w@1wt.eu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The USB net adapter Buffalo LUA-U2-GT (0411:006e) carries a AX88178 chip.
Tested on the above HW.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Acked-off-by: David Hollis <dhollis@davehollis.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/sx.c: In function 'sx_set_real_termios':
drivers/char/sx.c:973: warning: format '%u' expects type 'unsigned int', but argument 2 has type 'long unsigned int'
drivers/char/sx.c:999: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'tcflag_t'
drivers/char/sx.c:1012: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'tcflag_t'
sparc32 seems to use weird types for its tty things.
[ Fine by me but this is ancient debug and most of the debug in sx just
wants deleting eventually. - Alan ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'put_char' of 'struct tty_operations' has changed from 'void' into 'int'.
This can also shut up compiler warnings.
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: WANG Cong <wangcong@zeuux.org>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/md/raid10.c:889:17: warning: Using plain integer as NULL pointer
drivers/media/video/cx18/cx18-driver.c:616:12: warning: Using plain integer as NULL pointer
sound/oss/kahlua.c:70:12: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file drivers/usb/serial/iuu_phoenix.c uses "int" for flags. This can
cause hard to find bugs on some architectures. This patch converts the flags
to use "long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file in drivers/rtc/rtc-ds1551.c uses "int" for flags. This can cause
hard to find bugs on some architectures. This patch converts the flags to use
"long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some files in the drivers/media/video/saa7134 directory uses "int" for flags.
This can cause hard to find bugs on some architectures. This patch converts
the flags to use "long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A file in the net/mac80211 directory uses "int" for flags. This can cause
hard to find bugs on some architectures. This patch converts the flags to use
"long" instead.
This bug was discovered by doing an allyesconfig make on the -rt kernel where
checks are done to ensure all flags are of size sizeof(long).
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that
static void uart_flush_buffer(struct tty_struct *tty)
{
struct uart_state *state = tty->driver_data;
struct uart_port *port = state->port;
unsigned long flags;
/*
* This means you called this function _after_ the port was
* closed. No cookie for you.
*/
if (!state || !state->info) {
WARN_ON(1);
return;
}
is too late for checking state != NULL.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a small explanation of what accessibility is.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Related to d3930614e6.
RCSR is only present on PXA2xx CPUs, not on PXA3xx CPUs. Therefore,
we should not be unconditionally writing to RCSR from generic code.
Since we now clear the RCSR status from the SoC specific PXA PM code
and before reset in the arch_reset() function, the duplication in
the corgi, poodle, spitz and tosa code can be removed.
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The conversion between virtual and real time is as follows:
dvt = rw/w * dt <=> dt = w/rw * dvt
Since we want the fair sleeper granularity to be in real time, we actually
need to do:
dvt = - rw/w * l
This bug could be related to the regression reported by Yanmin Zhang:
| Comparing with kernel 2.6.25, sysbench+mysql(oltp, readonly) has lots
| of regressions with 2.6.26-rc1:
|
| 1) 8-core stoakley: 28%;
| 2) 16-core tigerton: 20%;
| 3) Itanium Montvale: 50%.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yanmin Zhang reported:
| Comparing with kernel 2.6.25, AIM7 (use tmpfs) has more th
| regression under 2.6.26-rc1 on my 8-core stoakley, 16-core tigerton,
| and Itanium Montecito. Bisect located the patch below:
|
| 64ac24e738 is first bad commit
| commit 64ac24e738
| Author: Matthew Wilcox <matthew@wil.cx>
| Date: Fri Mar 7 21:55:58 2008 -0500
|
| Generic semaphore implementation
|
| After I manually reverted the patch against 2.6.26-rc1 while fixing
| lots of conflicts/errors, aim7 regression became less than 2%.
i reproduced the AIM7 workload and can confirm Yanmin's findings that
-.26-rc1 regresses over .25 - by over 67% here.
Looking at the workload i found and fixed what i believe to be the real
bug causing the AIM7 regression: it was inefficient wakeup / scheduling
/ locking behavior of the new generic semaphore code, causing suboptimal
performance.
The problem comes from the following code. The new semaphore code does
this on down():
spin_lock_irqsave(&sem->lock, flags);
if (likely(sem->count > 0))
sem->count--;
else
__down(sem);
spin_unlock_irqrestore(&sem->lock, flags);
and this on up():
spin_lock_irqsave(&sem->lock, flags);
if (likely(list_empty(&sem->wait_list)))
sem->count++;
else
__up(sem);
spin_unlock_irqrestore(&sem->lock, flags);
where __up() does:
list_del(&waiter->list);
waiter->up = 1;
wake_up_process(waiter->task);
and where __down() does this in essence:
list_add_tail(&waiter.list, &sem->wait_list);
waiter.task = task;
waiter.up = 0;
for (;;) {
[...]
spin_unlock_irq(&sem->lock);
timeout = schedule_timeout(timeout);
spin_lock_irq(&sem->lock);
if (waiter.up)
return 0;
}
the fastpath looks good and obvious, but note the following property of
the contended path: if there's a task on the ->wait_list, the up() of
the current owner will "pass over" ownership to that waiting task, in a
wake-one manner, via the waiter->up flag and by removing the waiter from
the wait list.
That is all and fine in principle, but as implemented in
kernel/semaphore.c it also creates a nasty, hidden source of contention!
The contention comes from the following property of the new semaphore
code: the new owner owns the semaphore exclusively, even if it is not
running yet.
So if the old owner, even if just a few instructions later, does a
down() [lock_kernel()] again, it will be blocked and will have to wait
on the new owner to eventually be scheduled (possibly on another CPU)!
Or if another task gets to lock_kernel() sooner than the "new owner"
scheduled, it will be blocked unnecessarily and for a very long time
when there are 2000 tasks running.
I.e. the implementation of the new semaphores code does wake-one and
lock ownership in a very restrictive way - it does not allow
opportunistic re-locking of the lock at all and keeps the scheduler from
picking task order intelligently.
This kind of scheduling, with 2000 AIM7 processes running, creates awful
cross-scheduling between those 2000 tasks, causes reduced parallelism, a
throttled runqueue length and a lot of idle time. With increasing number
of CPUs it causes an exponentially worse behavior in AIM7, as the chance
for a newly woken new-owner task to actually run anytime soon is less
and less likely.
Note that it takes just a tiny bit of contention for the 'new-semaphore
catastrophy' to happen: the wakeup latencies get added to whatever small
contention there is, and quickly snowball out of control!
I believe Yanmin's findings and numbers support this analysis too.
The best fix for this problem is to use the same scheduling logic that
the kernel/mutex.c code uses: keep the wake-one behavior (that is OK and
wanted because we do not want to over-schedule), but also allow
opportunistic locking of the lock even if a wakee is already "in
flight".
The patch below implements this new logic. With this patch applied the
AIM7 regression is largely fixed on my quad testbox:
# v2.6.25 vanilla:
..................
Tasks Jobs/Min JTI Real CPU Jobs/sec/task
2000 56096.4 91 207.5 789.7 0.4675
2000 55894.4 94 208.2 792.7 0.4658
# v2.6.26-rc1-166-gc0a1811 vanilla:
...................................
Tasks Jobs/Min JTI Real CPU Jobs/sec/task
2000 33230.6 83 350.3 784.5 0.2769
2000 31778.1 86 366.3 783.6 0.2648
# v2.6.26-rc1-166-gc0a1811 + semaphore-speedup:
...............................................
Tasks Jobs/Min JTI Real CPU Jobs/sec/task
2000 55707.1 92 209.0 795.6 0.4642
2000 55704.4 96 209.0 796.0 0.4642
i.e. a 67% speedup. We are now back to within 1% of the v2.6.25
performance levels and have zero idle time during the test, as expected.
Btw., interactivity also improved dramatically with the fix - for
example console-switching became almost instantaneous during this
workload (which after all is running 2000 tasks at once!), without the
patch it was stuck for a minute at times.
There's another nice side-effect of this speedup patch, the new generic
semaphore code got even smaller:
text data bss dec hex filename
1241 0 0 1241 4d9 semaphore.o.before
1207 0 0 1207 4b7 semaphore.o.after
(because the waiter.up complication got removed.)
Longer-term we should look into using the mutex code for the generic
semaphore code as well - but i's not easy due to legacies and it's
outside of the scope of v2.6.26 and outside the scope of this patch as
well.
Bisected-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Found these two bugs while browsing through the code. The first one is
a cut-n-paste bug, instead of disabling the clock when request_irq()
fails, it enabled it once more. The second one fixes a debug printout,
AT91_SSC_IER is write only, AT91_SSC_IMR is readable (the printed string
actually says imr).
Frank Mandarino was busy so he asked me to send these to this list.
/Patrik
Signed-off-by: Patrik Sevallius <patrik.sevallius@enea.com>
Acked-by: Frank Mandarino <fmandarino@endrelia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's more checkpatch stuff to fix in the driver, this just fixes the
minimum required for the following patch to be clean.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
arch/arm/mach-pxa/lubbock.c:399: error: expected '}' before ';' token
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dev_open() and dev_close() must be called holding the RTNL, since they
call device functions and netdevice notifiers that are promised the RTNL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx packet counting and the local loopback of CAN frames should
only happen in the case that the CAN frame has been enqueued to the
netdevice tx queue successfully.
Thanks to Andre Naujoks <nautsch@gmail.com> for reporting this issue.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Urs Thuermann <urs@isnogud.escape.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a net namespace is destroyed, some devices (those, not killed
on ns stop explicitly) are moved back to init_net.
The problem, is that this net_ns change has one point of failure -
the __dev_alloc_name() may be called if a name collision occurs (and
this is easy to trigger). This allocator performs a likely-to-fail
GFP_ATOMIC allocation to find a suitable number. Other possible
conditions that may cause error (for device being ns local or not
registered) are always false in this case.
So, when this call fails, the device is unregistered. But this is
*not* the right thing to do, since after this the device may be
released (and kfree-ed) improperly. E. g. bridges require more
actions (sysfs update, timer disarming, etc.), some other devices
want to remove their private areas from lists, etc.
I. e. arbitrary use-after-free cases may occur.
The proposed fix is the following: since the only reason for the
dev_change_net_namespace to fail is the name generation, we may
give it a unique fall-back name w/o %d-s in it - the dev<ifindex>
one, since ifindexes are still unique.
So make this change, raise the failure-case printk loglevel to
EMERG and replace the unregister_netdevice call with BUG().
[ Use snprintf() -DaveM ]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When conntrack and DCCP/SCTP protocols are enabled, chances are good
that people also want DCCP/SCTP conntrack and NAT support.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Inovaphone PBXs exhibit very stange behaviour: when dialing for
example "123", the device sends INVITE requests for "1", "12" and
"123" back to back. The first requests will elicit error responses
from the receiver, causing the SIP helper to flush the RTP
expectations even though we might still see a positive response.
Note the sequence number of the last INVITE request that contained a
media description and only flush the expectations when receiving a
negative response for that sequence number.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Ben Greear, macvlan crashes the kernel when unloading the
module. The reason is that it tries to clean up the macvlan_port pointer
on the macvlan device itself instead of the underlying device. A non-NULL
pointer is taken as indication that the macvlan_handle_frame_hook is
valid, when receiving the next packet on the underlying device it tries
to call the NULL hook and crashes.
Clean up the macvlan_port on the correct device to fix this.
Signed-off-by; Patrick McHardy <kaber@trash.net>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 1122 does not have a section 3.1.2.2. The requirement to silently
discard datagrams with a bad checksum is in section 3.2.1.2 instead.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=10611
Signed-off-by: J.H.M. Dassen (Ray) <jdassen@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: there's actually another bug in FRTO's SACK variant, which
is the causing failure in NewReno case because of the error
that's fixed here. I'll fix the SACK case separately (it's
a separate bug really, though related, but in order to fix that
I need to audit tp->snd_nxt usage a bit).
There were two places where SACK variant of FRTO is getting
incorrectly used even if SACK wasn't negotiated by the TCP flow.
This leads to incorrect setting of frto_highmark with NewReno
if a previous recovery was interrupted by another RTO.
An eventual fallback to conventional recovery then incorrectly
considers one or couple of segments as forward transmissions
though they weren't, which then are not LOST marked during
fallback making them "non-retransmittable" until the next RTO.
In a bad case, those segments are really lost and are the only
one left in the window. Thus TCP needs another RTO to continue.
The next FRTO, however, could again repeat the same events
making the progress of the TCP flow extremely slow.
In order for these events to occur at all, FRTO must occur
again in FRTOs step 3 while the key segments must be lost as
well, which is not too likely in practice. It seems to most
frequently with some small devices such as network printers
that *seem* to accept TCP segments only in-order. In cases
were key segments weren't lost, things get automatically
resolved because those wrongly marked segments don't need to be
retransmitted in order to continue.
I found a reproducer after digging up relevant reports (few
reports in total, none at netdev or lkml I know of), some
cases seemed to indicate middlebox issues which seems now
to be a false assumption some people had made. Bugzilla
#10063 _might_ be related. Damon L. Chesser <damon@damtek.com>
had a reproducable case and was kind enough to tcpdump it
for me. With the tcpdump log it was quite trivial to figure
out.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be more liberal about the alignment of the buffer given to
us by sigaltstack(). The user should not need to be mindful of all of
the alignment constraints we have for the stack frame.
This mirrors how we handle this situation in clone() as well.
Also, we align the stack even in non-SA_ONSTACK cases so that signals
due to bad stack alignment can be delivered properly. This makes such
errors easier to debug and recover from.
Finally, add the sanity check x86 has to make sure we won't overflow
the signal stack.
This fixes glibc testcases nptl/tst-cancel20.c and
nptl/tst-cancelx20.c
Signed-off-by: David S. Miller <davem@davemloft.net>
