Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b475d78 lacked two pairs of parenthesis, causing an overflow in the
congestion management.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A semantic patch, fixing style issues in the bnx2x's link code.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch revises the way by which rss are configured, removing
an unnecessary module paramater and unrequired modes.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The congestion management code has migrated into a common location,
allowing all fw writes controlling mf congestion to be made in a
single function in the code. This is a semantic change.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notice this patch includes lines with over 80 characters, as to not
break strings.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore remote-faule detection, which periodically checks for
remote-fault on the MAC layer. In case physical link appear to be
up but fault is set, it will provide a link down indication, and
when the fault is cleared, it will indicate link up again.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the bnx2x driver needed at least 2 available msix interrupt
vectors in order to use msix. This patch add the possibility of configuring
msix when only one interrupt vector is available.
Notice this patch contains lines with over 80 characters, as it keeps print
strings in a single line.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During boot-from-SAN, if msix interrupts are unavailable and inta
is requested, it is possible that inta would be disabled in the
pci bus. This patch enables inta when requested.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed uninformative debug prints, as well as two functions
which were hardly used in the code.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 621b4d6 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the bug that may prevent from mac to be configured,
while there is an empty slot for it.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously applied patch making the bnx2x statistics consistent
did not apply to old FWs. This remedies it, extending the consistent
behaviour to all drivers.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes changes in macros to better distinguish between the two
protocols, and slightly changed the way their macs are set.
Notice this file contains string print lines with more than 80 characters,
as to not break prints.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new error flags are supported by the bnx2x FW.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes were mostly made to enable back-to-back data flow with dcb.
Other changes were simply deemed as a better 'clean' initial configuration.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces sparse warnings in the bnx2x code,
mostly by changing functions into static and changing
initialization of structures.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've revised driver prints, changing the mask of existing prints
to allow better control over the debug messages, added prints to
error scenarios, removed unnecessary prints and corrected some spelling.
Please note that this patch contains lines with over 80 characters,
as string messages were kept in a single line.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.
Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, allocation used queue statistics directly in its calcualtion.
This change causes these calculations to be summed into the statistics,
without being affected by them.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, if autoneg failed, ethtool would return the achieved autoneg.
This patch corrects this, causing ethtool to return the requested autoneg
capabilities even if autoneg fails.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, unless both interface and link were up, ethtool returned
the requested speed/duplex when asked for the interface's settings.
This change will now enable the driver to answer correctly (i.e.,
return unknown as its answer).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables the FW to make more accurate decisions regarding the
active functions.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've used the object's function id instead of using the
input's value. This is remedied, as in other flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we used a hard-coded value as paramater, instead of using the
input's value. This is now remedied, as in other flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These definitions are united into the header.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCoE statistics ids were distinguished from the L2's statistics ids.
However, not all of the change was committed. This causes a possible
collision of indices when FCoE is present.
This patch fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DCB flags were updated using the flags' bit offsets instead of
the actual bits. This is now fixed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed endianess issue when passing arguments to FW.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pfc statistics were counted, the delta change from last count
was summed twice. This fixes the issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
{g|s}etnumtcs() today returns a u8 that is only used by the DCB code
to verify no error occurred. Today the driver implementations return
negative error codes which end up being non-zero so the logic works
out but triggers some sparse warnings.
To fix the sparse warnings convert the return value to an int.
CC: Eilon Greenstein <eilong@broadcom.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch provides workaround for BUG in FW 7.2.16,
which in GRO mode may miscalculate buffer and
place on SGE one frag less than it could.
It may happen only for some MTUs, we mark these MTUs
with gro_check flag during device initialization or
MTU change.
Next FW should include fix for the issue and the
patch could be reverted.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch integrates FW 7.2.16 HSI and implements driver
part of GRO flow.
FW 7.2.16 adds the ability to aggregate packets for GRO
(and not just LRO) and also fixes some bugs.
1. Added new aggregation mode: GRO. In this mode packets are aggregated
such that the original packets can be reconstructed by the OS.
2. 57712 HW bug workaround - initialized all CAM TM registers to 0x32.
3. Adding the FCoE statistics structures to the BNX2X HSI.
4. Wrong configuration of TX HW input buffer size may cause theoretical
performance effect. Performed configuration fix.
5. FCOE - Arrival of packets beyond task IO size can lead to crash.
Fix firmware data-in flow.
6. iSCSI - In rare cases of on-chip termination the graceful termination
timer hangs, and the termination doesn't complete. Firmware fix to MSL
timer tolerance.
7. iSCSI - Chip hangs when target sends FIN out-of-order or with isles
open at the initiator side. Firmware implementation corrected to drop
FIN received out-of-order or with isles still open.
8. iSCSI - Chip hangs when in case of retransmission not aligned to 4-bytes
from the beginning of iSCSI PDU. Firmware implementation corrected
to support arbitrary aligned retransmissions.
9. iSCSI - Arrival of target-initiated NOP-IN during intense ISCSI traffic
might lead to crash. Firmware fix to relevant flow.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8304859a "bnx2x: add fan failure event handling" made the function
bnx2x_close() non-static unnecessarily. The function is not called from
other sources. Make it static again.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy FW version is stored in regular memory, no MDC-MDIO access or
any special locks are required to read it in the current implementation.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Merav Sicron <meravs@broadcom.com>
Current ethtool self tests usesa large buffer on stack. This patch replaces
that array by dynamically allocated memory
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the changes in the ethtool source code, this patch enables
the bnx2x driver to publish the Link partner's capabilities s, when ethtool
is used on an interface which completed autoneg.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Yaniv Rosner <yaniv.rosner@broadcom.com>
Several boards require an additional HW bit written in-order to enable
half duplex.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently bnx2x statistics are reset by inner driver reload, e.g. by MTU
change. This patch fixes this issue - from now on statistics should only
be reset upon device closure.
Thanks to Michal Schmidt <mschmidt@redhat.com> for his initial patch
regarding this issue.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'poll' was a debugging option, but turning it on these days leads to
kernel panic. Remove it.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 619c5cb688 (New 7.0 FW: bnx2x, cnic, bnx2i, bnx2fc) added new
sparse warnings.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Vladislav Zolotarov <vladz@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allocate memory for 'new_data' with kmalloc(). If we get the memory
we then try to build_skb() and if that should fail (which it can) we
do not enter 'if (likely(skb)) {' and actually use 'new_data' but
instead fall through to the 'drop:' label and end up returning from
the function without ever assigning 'new'data' to anything or freeing
it. That leaks the memory allocated to 'new_data'.
This patch fixes the memory leak by doing a kfree(new_data) in the
case where build_skb() fails (or where allocation of 'new_data' itself
fails, but in taht case it's just a harmless kfree(NULL)).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics for tracking parity errors from which we successfully
recovered and those which were deemed unrecoverable.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Sample mcp pulse and mcp sequence in nic load instead of in init_one
as they may change by the time we want to use them.
2. Allow cnic to access device during nic load (by adding a new "LOADING" state
to recovery flow). This prevents the unnecessary cnic timeout which resulted
by cnic attempting to access because nic is loading, but being blocked because
of the Recovery state.
3. Issue 'fake' driver load command to mcp when last driver unloads to prevent
mcp from taking ownership. When recovery is complete unload fake driver to
allow mcp to initialize the hardware before first driver loads.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery register (to which a hardware lock has been added in previous
patch) is used amongst other things to track the active PFs. The old
implementation which used a per path counter is not viable in a virtualized
environment where a pf may increment the counter and then have the kernel
crash around it preventing the counter from ever reaching zero.
In the new implementation the scenario described will result in the PF timing
out against the mcp, which will clear the PF's bit in the bitmask allowing
recovery process to proceed.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use hardware locks to protect resources common to several Physical Functions. In
a virtualized environment the RTNL lock only protects a PF's driver against
the PFs sharing it's VMs with regard to device resources. Other PFs may reside
in other VMs under other OSs, and are not subject to the lock. Such resources
which were previously protected implicitly by the RTNL lock must now be
protected explicitly with dedicated HW locks.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a virtualized environment it is possible for a loading driver to discover
that Firmware is already loaded to the device, and that this FW does not match
its own. This can happen for example if different Physical Functions are
Assigned to different VMs in which different driver versions are loaded. The
code in this patch ensures that only drivers with matching FW are loaded over
the device, and that in the case described above where the Firmware version
doesn't match the driver load is aborted.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Fix bug where return value is ignored
2. Improve printouts
3. Fix typos
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BDF was obtained from kernel but since in virtualized environment
(e.g. physical device assigment in KVM) the function number may
not be the real one, the info must be obtained from the device.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In virtualized environments indirect access to the device may not be supported
(depending on the Hypervisor type). Indirect device access was used since in
some harware contexts (i.e. certain chipset and BIOS) every access the driver
makes across the pci is followed by a BIOS initiated Zero Length Read to the
same address. When accessing widebus registers this zero length read corrupts
the serialization of the read/write sequence resulting with errors. To avoid
this problem widebus registers are always accessed via the DMAE or the indirect
interface. However, the 57712x and 578xx devices intercept the zero length read
and so using the indirect interface with these devices is not necessary. Since
PDA is only supported for 57712x and 578xx the indirect access to device was
restricted to 57710 and 57711x.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the use of up to three hardware queues for transmission. The queues
are always dequed round robin (i.e. strict priority, PFC and ETS are not
supported). This does allow the allocation of a seperate HW queue for low
volume, high priority traffic which will be serviced more promptly.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduced a new return here but forgot to drop the lock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro `CHIP_IS_E1x' requires `bp' to be initialized.
As `bp' is not yet initialized during this phase of `bnx2x_init_dev',
it accessed uninitialized fields in the struct.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previosuly, in MF modes `ethtool -S' lacked some of the statistics
which appeared in non-MF modes. This has been fixed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon insertion of elements into the execution queue, it is validated
that there are enough credits to support additional vlan-macs,
and the credits are consumed. However, when removing a pending
command in `bnx2x_vland_mac_del_all' the consumed credits are not
released, which might cause leakage and eventually the inability to
add new vlan-macs in certain scenarios.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the work-around for the autoneg KR of the BCM57810 in case the Warpcore version is 0xD108 and above, which fixes this problem.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable the autoGrEEEn feature for BCM84833.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unsupported speed of 100Mb force for BCM84833 due to hardware
limitation.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles the second port of a path in a 4-port device of
BCM57840.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Super-Isolate mode comes to isolate the BCM84833 PHY from the
outside world. Not doing it correctly, made link partner see the link
before the driver was loaded.
This patch also involves SPIROM version fixes since it is used to
determine whether the common init of the PHY was already executed, and
the common init of this PHY is partially responsible for setting the
Super-Isolate mode.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that support modification of the RX flow hash indirection
table initialise it in the same way: RX rings are assigned to table
entries in rotation. Make that default policy explicit by having them
call a ethtool_rxfh_indir_default() function.
In the ethtool core, add support for a zero size value for
ETHTOOL_SRXFHINDIR, which resets the table to this default.
Partly-suggested-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new ethtool operation (get_rxfh_indir_size) to get the
indirectional table size. Use this to validate the user buffer size
before calling get_rxfh_indir or set_rxfh_indir. Use get_rxnfc to get
the number of RX rings, and validate the contents of the new
indirection table before calling set_rxfh_indir. Remove this
validation from drivers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit e52fcb2462 newly allocated
skb for small packets are not updated properly and dropped by stack.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is missing initialization of NO_FCOE_FLAG and NO_ISCSI*FLAGS
when CONFIG_CNIC is not selected.
This causes panic during driver load since commit
1d187b34da where NO_FCOE tested
unconditionally (outside #ifdef BCM_CNIC structure) and
accessed fp[FCOE_IDX] which is not allocated.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide FCoE and iSCSI statistics to management firmware if
CONFIG_CNIC is not set. Some needed structure fields are not defined
without CONFIG_CNIC.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2df1a70aaf "bnx2x: Support
for byte queue limits" has introduced an asymmetry in usage of
netdev_tx_completed_queue and netdev_tx_sent_queue. Missing
call to netdev_tx_sent_queue causes the crash during ethtool -t.
The patch adds the missing call.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to send driver capabilities, settings and statistics to
management firmware.
[ Redone using many local variables, removed many unnecessary inlines,
and put #defines at the left margin suggested by Joe Perches ]
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support copying MAC addresses to firmware query structure.
[ Fixed up style and formatting errors noted by DaveM and Joe Perches ]
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FCoE statistics support for FCoE capable devices.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Priority flow control counters for ethtool -S.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
in iSCSI SD mode to bnx2x device assigned single mac address
which is supposted to be iscsi mac. If this mode is recognized
bnx2x will disable LRO, decrease number of queues to 1 and rx ring
size to the minumum allowed by FW, this in order minimize memory use.
It will tranfer mac for iscsi usage and zero primary mac of the netdev.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to bnx2x to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change comparison order such that the variable will come before the compared value.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the MAC test of the 1G port of the BCM57800 to use the UMAC instead of the XMAC.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The populate function will fail in case an unknown external PHY is detected.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the usage of simpler MDC/MDIO work-around when accessing Warpcore registers.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contain several fixes for the BCM84833. This PHY is still not in bnx2x production, hence this patch can be considered as enhancement.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put Warpcore in low power mode in case of fan failure to reduce heat.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem when new traffic class is created with 0% BW, the ETS is not conforming.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change BRB to work in per class guaranteed mode and handle cases for BW 0%.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix port identify test on 5461x PHY by driving LEDs through MDIO.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_assign_pointer(ptr, NULL) can be safely replaced by
RCU_INIT_POINTER(ptr, NULL)
(old rcu_assign_pointer() macro was testing the NULL value and could
omit the smp_wmb(), but this had to be removed because of compiler
warnings)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forcedeth changes had a conflict with the conversion over
to atomic u64 statistics in net-next.
The libertas cfg.c code had a conflict with the bss reference
counting fix by John Linville in net-next.
Conflicts:
drivers/net/ethernet/nvidia/forcedeth.c
drivers/net/wireless/libertas/cfg.c
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-request fw from fs may fail for different reasons, once the fw was
loaded we won't release it until driver is removed.
This also resolves the boot problem when initial fw is located on initrd,
but rootfs is still unavailable, in this case device reset will fail due
to absence of fw files.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x uses following formula to compute its rx_buf_sz :
dev->mtu + 2*L1_CACHE_BYTES + 14 + 8 + 8 + 2
Then core network adds NET_SKB_PAD and SKB_DATA_ALIGN(sizeof(struct
skb_shared_info))
Final allocated size for skb head on x86_64 (L1_CACHE_BYTES = 64,
MTU=1500) : 2112 bytes : SLUB/SLAB round this to 4096 bytes.
Since skb truesize is then bigger than SK_MEM_QUANTUM, we have lot of
false sharing because of mem_reclaim in UDP stack.
One possible way to half truesize is to reduce the need by 64 bytes
(2112 -> 2048 bytes)
Instead of allocating a full cache line at the end of packet for
alignment, we can use the fact that skb_shared_info sits at the end of
skb->head, and we can use this room, if we convert bnx2x to new
build_skb() infrastructure.
skb_shared_info will be initialized after hardware finished its
transfert, so we can eventually overwrite the final padding.
Using build_skb() also reduces cache line misses in the driver, since we
use cache hot skb instead of cold ones. Number of in-flight sk_buff
structures is lower, they are recycled while still hot.
Performance results :
(820.000 pps on a rx UDP monothread benchmark, instead of 720.000 pps)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Tom Herbert <therbert@google.com>
CC: Jamal Hadi Salim <hadi@mojatatu.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: Thomas Graf <tgraf@infradead.org>
CC: Herbert Xu <herbert@gondor.apana.org.au>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The race may cause access of registers while MAC hw block is
in reset state. As a result syslog will show error messages.
We can prevent this by using state from local variable.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shut down the device in case of fan failure to prevent HW damage.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need propagate the DCBX results from PMF to other functions
on the same port, in order to properly update netdev structure
and allow following new ETS and PFC configurations.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FCoE license info must be initialized at probe(), but
iSCSI at open().
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW includes the following fixes:
1. (iSCSI) Arrival of un-solicited ASYNC message causes
firmware to abort the connection with RST.
2. (FCoE) There is a probability that truncated FCoE packet on
RX path won't get detected which might lead to FW assert.
3. (iSCSI) Arrival of target-initiated NOP-IN during intense
ISCSI traffic might lead to FW assert.
4. (iSCSI) Chip hangs when in case of retransmission not aligned
to 4-bytes from the beginning of iSCSI PDU.
5. (FCoE) Arrival of packets beyond task IO size can lead to crash.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem in which the host stops receiving data after
restarting the interface. This issue is caused by combination of incorrect
data path tap closure, along with missing MAC reset.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix solves a problem of no link on 578xx-KR by retrying to link up to
four timer using the periodic function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust blink rate on 578xx to fit its clock rate.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x allocates a full page per fragment.
We must account in skb->truesize, the size of the fragment, not the used
part of it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per comments from Ben Hutchings on a previous patch, sweep the floors
a little removing unnecessary assignments of zero to fields of struct
ethtool_ringparam in driver code supporting ethtool -g.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is after the break statement so it never gets used. The
"vlan_mac_obj" variable does get initialized properly, so we can just
delete this.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.
Add note that drivers must not use ethtool_rxnfc::rule_locs.
The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Mon, 2011-08-29 at 13:28 -0700, Randy Dunlap wrote:
> (on i386 or x86_64)
>
> drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:10148: error: 'bnx2x_fcoe_get_wwn' undeclared here (not in a function)
This should sync #define structures between definition and declaration
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54616 PHY is very similar to the 54618SE, only without EEE support, which will not be activated due to querying the actual PHY type.
This check is already done by reading a dedicated PHY register.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x used to be able to set rxhash, but this was lost in the conversion
to hw_features (commit 66371c441).
Restore it and enable it by default.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
CC: Vladislav Zolotarov <vladz@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Dmitry Kravkov <dmitry@broadcom.com>
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
