Interface configuration table is used to configure PCI PHY that are
normally decided by design or bootstrap pin, and driver can do additional
settings by this table.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-9-yhchuang@realtek.com
DIG sets only one IG register for most chips, but 8723D need to set
additional register for CCK rate.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-8-yhchuang@realtek.com
This ops is used to do statistics of false alarm periodically, and then
fine tune RX initial gain to adaptive different circumstance.
There are three steps, hold/get/reset counter, to retrieve false alarm
counters that consist of CCK and OFDM. In addition to false alarm
counters, it also collects CRC ok/error counters of CCK, OFDM and HT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-7-yhchuang@realtek.com
Some chips are not able to receive LDPC packets. Add an attribute
to rtw_chip_info to determine if the LDPC capability in [ht/vht]_cap
should be advertised or not.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-6-yhchuang@realtek.com
TX status report of 8723D differs from 8822B/8822C, it uses
C2H_CCX_TX_RPT (0x03) with different format. With sequence number
and TX status, driver can know if certain packet was transmitted
successfully.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-5-yhchuang@realtek.com
Set MAC/BB/RF register according to specified channel. The function
rtw_set_channel_mac() is used to set MAC registers, but 8723D only need
some of them.
For channel 14, we need to set different CCK DFIR values, so restore the
values when channel 1 to 13 is selected.
Spur calibration is needed in channel 13 and 14, and we do notch if spur
is over threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-4-yhchuang@realtek.com
This ops is used to parse RX descriptor to know the length of received
packet and containing PHY status. If PHY status is existing, the order is
RX descriptor, PHY status and then packet.
There are two types of PHY status, named CCK and OFDM. Their size are the
same, but formats are different.
struct ieee80211_rx_status is also filled depends on above information.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-3-yhchuang@realtek.com
To improve user experience in field, we need DIG to adjust RX initial gain
depends on field situation. Since each chip has its own register address,
this commit defines 8723d specific address.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504105010.10780-2-yhchuang@realtek.com
Fix the following coccicheck warning:
drivers/net/wireless/ray_cs.c:2797:5-14: WARNING: Comparison of 0/1 to
bool variable
drivers/net/wireless/ray_cs.c:2798:2-11: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426103709.6730-1-yanaijie@huawei.com
The 'blocked' is a bool variable, and '==' expression itself is bool
too. So no need to convert it to 0/1.
This fixes the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/base.c:508:13-41: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200426094115.23294-1-yanaijie@huawei.com
Axe a memory allocation failure log message. This message is useless and
incorrect (vmalloc is not used here for the memory allocation)
This has been like that since the very beginning of this driver in
commit 43f66a6ce8 ("Add ipw2200 wireless driver.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424154527.27309-1-christophe.jaillet@wanadoo.fr
It's incorrect to use usleep in atomic context.
Switch to a macro which uses udelay instead of usleep to prevent the issue.
Fixes: 6343a6d4b2 ("rtw88: Add delay on polling h2c command status bit")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200423073007.3566-1-kai.heng.feng@canonical.com
Like read_poll_timeout, an atomic variant for multiple parameter read
function can be useful.
Will be used by a later patch.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200424184918.30360-1-kai.heng.feng@canonical.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504201224.GA32282@embeddedor
Some devices like TP-Link TL-WN722N produces this kind of messages
frequently.
kernel: ath: phy0: Short RX data len, dropping (dlen: 4)
This warning is useful for developers to recognize that the device
(Wi-Fi dongle or USB hub etc) is noisy but not for general users. So
this patch make this warning to debug message.
Reported-By: Denis <pro.denis@protonmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207539
Fixes: cd486e627e ("ath9k_htc: Discard undersized packets")
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504214443.4485-1-masashi.honma@gmail.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504200838.GA31974@embeddedor
This patch add supports to reset the per peer htt stats.
Usage:
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/<peer MAC addr>/htt_peer_stats_reset
While doing so, sync the wmi services between FW and host.
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588610147-20231-1-git-send-email-tamizhr@codeaurora.org
This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
* Avoid loading asus-nb-wmi module on selected laptop models
* Fix S0ix debug support for Jasper Lake PMC
* Few fixes which have been reported by Hulk bot and others
The following is an automated git shortlog grouped by driver:
asus-nb-wmi:
- Do not load on Asus T100TA and T200TA
intel_pmc_core:
- avoid unused-function warnings
- Change Jasper Lake S0ix debug reg map back to ICL
platform/x86/intel-uncore-freq:
- make uncore_root_kobj static
surface3_power:
- Fix a NULL vs IS_ERR() check in probe
thinkpad_acpi:
- Remove always false 'value < 0' statement
wmi:
- Make two functions static
-----BEGIN PGP SIGNATURE-----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=u8gZ
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.7-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- Avoid loading asus-nb-wmi module on selected laptop models
- Fix S0ix debug support for Jasper Lake PMC
- Few fixes which have been reported by Hulk bot and others
* tag 'platform-drivers-x86-v5.7-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: thinkpad_acpi: Remove always false 'value < 0' statement
platform/x86: intel_pmc_core: avoid unused-function warnings
platform/x86: asus-nb-wmi: Do not load on Asus T100TA and T200TA
platform/x86: intel_pmc_core: Change Jasper Lake S0ix debug reg map back to ICL
platform/x86/intel-uncore-freq: make uncore_root_kobj static
platform/x86: wmi: Make two functions static
platform/x86: surface3_power: Fix a NULL vs IS_ERR() check in probe
When a new neighbor entry has been added, event is generated but it does not
include protocol, because its value is assigned after the event notification
routine has run, so move protocol assignment code earlier.
Fixes: df9b0e30d4 ("neighbor: Add protocol attribute")
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to have build configuration which will force PTP_1588_CLOCK=m
and so TI_K3_AM65_CPTS=m while still have TI_K3_AM65_CPSW_NUSS=y. This will
cause build failures:
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.o: in function `am65_cpsw_init_cpts':
../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685: undefined reference to `am65_cpts_create'
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685:(.text+0x2e20):
relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `am65_cpts_create'
Fix it by adding dependencies from CPTS in TI_K3_AM65_CPSW_NUSS as below:
config TI_K3_AM65_CPSW_NUSS
...
depends on TI_K3_AM65_CPTS || !TI_K3_AM65_CPTS
Note. This will create below dependencies and for NFS boot + CPTS all of them
have to be built-in.
PTP_1588_CLOCK -> TI_K3_AM65_CPTS -> TI_K3_AM65_CPSW_NUSS
While here, clean up TI_K3_AM65_CPTS definition.
Fixes: b1f66a5bee ("net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Type I ERSPAN frame format is based on the barebones
IP + GRE(4-byte) encapsulation on top of the raw mirrored frame.
Both type I and II use 0x88BE as protocol type. Unlike type II
and III, no sequence number or key is required.
To creat a type I erspan tunnel device:
$ ip link add dev erspan11 type erspan \
local 172.16.1.100 remote 172.16.1.200 \
erspan_ver 0
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to cast a typed pointer to a void pointer when calling
a function that accepts the latter. Remove it, as the cast prevents
further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul says:
====================
smc: log state changes and cleanup
Patch 1 adds the logging of important state changes to enable SMC-R
users to detect SMC-R link groups that are not redundant and require
user actions. Patch 2 is a contribution to clean up an unused inline
function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bac6de7b63 ("net/smc: eliminate cursor read and write calls")
left behind this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print to system log when SMC links are available or go down, link group
state changes or pnetids are applied to and removed from devices.
The log entries are triggered by either user configuration actions or
adapter activation/deactivation events and are not expected to happen
often. The entries help SMC users to keep track of the SMC link group
status and to detect when actions are needed (like to add replacements
for failed adapters).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix dt_binding_check fail:
Fix Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/net/ti,k3-am654-cpts.yaml#
Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.6/dist-packages/dtschema/schemas/net/ti,am654-cpts.yaml'
Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/net/ti,k3-am654-cpts.yaml#
Unknown file referenced: [Errno 2] No such file or directory: '/usr/local/lib/python3.6/dist-packages/dtschema/schemas/net/ti,am654-cpts.yaml'
Cc: Rob Herring <robh@kernel.org>
Fixes: 6e87ac748e ("dt-binding: ti: am65x: document common platform time sync cpts module")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 05cc5a39dd ("bnx2x: add vlan filtering offload")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no callers in-tree anymore since commit 5952fde10c ("net:
sched: choke: remove dead filter classify code")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 4ca3221fe4 ("myri10ge: Convert from LRO to GRO")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no caller in-tree since
commit 2af6106ae9 ("net: stmmac: Introducing support for Page Pool")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 84411f73b8 ("net: mv643xx_eth: Avoid setting the initial TCP checksum")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/ti/cpsw_new.c:1924:2-17: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/ti/cpsw_new.c:1231:1-16: WARNING: Assignment of
0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1991:5-46: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:1993:10-54: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnxt/bnxt_ethtool.c:2380:5-38: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/agere/et131x.c:717:3-22: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/agere/et131x.c:721:1-20: WARNING: Assignment of
0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to convert '==' expression to bool. This fixes the following
coccicheck warning:
drivers/net/ethernet/atheros/atl1c/atl1c_main.c:1189:63-68: WARNING:
conversion to bool not needed here
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/qlogic/qede/qede_main.c:1717:5-19: WARNING:
Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c:1548:17-31: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c:1148:16-24: WARNING:
Comparison to bool
drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c:1158:30-38: WARNING:
Comparison to bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:1585:3-25:
WARNING: Assignment of 0/1 to bool variable
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:1588:3-25:
WARNING: Assignment of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
