This kills off the unrolled segment based flushers on SH-4 and switches
over to a generic unrolled approach derived from the writethrough segment
flusher.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PHYSADDR() runs in to issues in 32-bit mode when we do not have the
legacy P1/P2 areas mapped, as such, we need to use page_to_phys()
directly, which also happens to do the right thing in legacy 29-bit mode.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The i-cache flush in the case of VM_EXEC was added way back when as a
sanity measure, and in practice we only care about evicting aliases from
the d-cache. As a result, it's possible to drop the i-cache flush
completely here.
After careful profiling it's also come up that all of the work associated
with hunting down aliases and doing ranged flushing ends up generating
more overhead than simply blasting away the entire dcache, particularly
if there are many mm's that need to be iterated over. As a result of
that, just move back to flush_dcache_all() in these cases, which restores
the old behaviour, and vastly simplifies the path.
Additionally, on platforms without aliases at all, this can simply be
nopped out. Presently we have the alias check in the SH-4 specific
version, but this is true for all of the platforms, so move the check up
to a generic location. This cuts down quite a bit on superfluous cacheop
IPIs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was quite a lot of tab->space damage done here from a former patch,
clean it up once and for all.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This supported all DMA channels, and it was tested in SH7722,
SH7780, SH7785 and SH7763.
This can not use with SH DMA API.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Now that the cache purging is handled manually by all copy_page()
callers, we can kill off copy_page()'s on writeback. This optimizes the
non-aliasing case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up a number of outstanding issues observed with old mappings
on the same colour hanging around. This requires some more optimal
handling, but is a safe fallback until all of the corner cases have been
handled.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the kmap_coherent/kunmap_coherent() interface for recent
changes both in the page fault path and the shared cache flushers, as
well as adding in some optimizations.
One of the key things to note here is that the TLB flush itself is
deferred until the unmap, and the call in to update_mmu_cache() itself
goes away, relying on the regular page fault path to handle the lazy
dcache writeback if necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a keyctl to install a process's session keyring onto its parent. This
replaces the parent's session keyring. Because the COW credential code does
not permit one process to change another process's credentials directly, the
change is deferred until userspace next starts executing again. Normally this
will be after a wait*() syscall.
To support this, three new security hooks have been provided:
cred_alloc_blank() to allocate unset security creds, cred_transfer() to fill in
the blank security creds and key_session_to_parent() - which asks the LSM if
the process may replace its parent's session keyring.
The replacement may only happen if the process has the same ownership details
as its parent, and the process has LINK permission on the session keyring, and
the session keyring is owned by the process, and the LSM permits it.
Note that this requires alteration to each architecture's notify_resume path.
This has been done for all arches barring blackfin, m68k* and xtensa, all of
which need assembly alteration to support TIF_NOTIFY_RESUME. This allows the
replacement to be performed at the point the parent process resumes userspace
execution.
This allows the userspace AFS pioctl emulation to fully emulate newpag() and
the VIOCSETTOK and VIOCSETTOK2 pioctls, all of which require the ability to
alter the parent process's PAG membership. However, since kAFS doesn't use
PAGs per se, but rather dumps the keys into the session keyring, the session
keyring of the parent must be replaced if, for example, VIOCSETTOK is passed
the newpag flag.
This can be tested with the following program:
#include <stdio.h>
#include <stdlib.h>
#include <keyutils.h>
#define KEYCTL_SESSION_TO_PARENT 18
#define OSERROR(X, S) do { if ((long)(X) == -1) { perror(S); exit(1); } } while(0)
int main(int argc, char **argv)
{
key_serial_t keyring, key;
long ret;
keyring = keyctl_join_session_keyring(argv[1]);
OSERROR(keyring, "keyctl_join_session_keyring");
key = add_key("user", "a", "b", 1, keyring);
OSERROR(key, "add_key");
ret = keyctl(KEYCTL_SESSION_TO_PARENT);
OSERROR(ret, "KEYCTL_SESSION_TO_PARENT");
return 0;
}
Compiled and linked with -lkeyutils, you should see something like:
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
355907932 --alswrv 4043 -1 \_ keyring: _uid.4043
[dhowells@andromeda ~]$ /tmp/newpag
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: _ses
1055658746 --alswrv 4043 4043 \_ user: a
[dhowells@andromeda ~]$ /tmp/newpag hello
[dhowells@andromeda ~]$ keyctl show
Session Keyring
-3 --alswrv 4043 4043 keyring: hello
340417692 --alswrv 4043 4043 \_ user: a
Where the test program creates a new session keyring, sticks a user key named
'a' into it and then installs it on its parent.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
This board doesn't use trapped I/O for anything, so just kill off the
select. This was causing problems in the unhandled page fault die path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This builds on top of the previous reversion and implements a special
on_each_cpu() variant that simple disables preemption across the call
while leaving the interrupt state to the function itself. There were some
unintended consequences with IRQ disabling in some of these paths on UP
that ran in to a deadlock scenario with IRQs being missed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 64a6d72213.
Unfortunately we can't use on_each_cpu() for all of the cache ops, as
some of them only require preempt disabling. This seems to be the same
issue that impacts the mips r4k caches, where this code was based on.
This fixes up a deadlock that showed up in some IRQ context cases.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The kgdb stub has traditionally tied in to the NMI slot, and manually
handled debounce. Now that we have a generic way to do this instead, all
of the stub-specific debounce silliness can be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements support for NMI debugging that was shamelessly copied
from the avr32 port. A bit of special magic is needed in the interrupt
exception path given that the NMI exception handler is stubbed in to the
regular exception handling table despite being reported in INTEVT. So we
mangle the lookup and kick off an EXPEVT-style exception dispatch from
the INTEVT path for exceptions that do_IRQ() has no chance of handling.
As a result, we also drop the evt2irq() conversion from the do_IRQ() path
and just do it in assembly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adopts the special-cased 2-way write-through dcache flusher for
N-ways and moves it in to the generic path. Assignment is done at runtime
via the check for the CCR_CACHE_WT bit in the same path as the per-way
writeback flushers.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some unaligned accesses are completely expected. For example, the
trapped_io code uses the unaligned access fixup code path so there's no
need to warn about having to fixup the unaligned access.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The method of ETHER_LINK pin is board dependence.
This patch adding paramters are:
- no_ether_link : If set to 1, do not use ETHER_LINK
- ether_link_active_low : If set to 1, ETHER_LINK is active low.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is supposed to be the equivalent of __NR_syscalls, not
__NR_syscalls -1. The x86 code this was based on had simply fallen
out of sync at the time this was implemented. Fix it up now.
As a result, tracing of __NR_perf_counter_open works as advertised.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The recent commit "timekeeping: Increase granularity of
read_persistent_clock()" introduced read_persistent_clock()
rework which inadvertently broke the sh conversion:
arch/sh/kernel/time.c:45: error: passing argument 1 of 'rtc_sh_get_time' from incompatible pointer type
distcc[13470] ERROR: compile arch/sh/kernel/time.c on sprygo/32 failed
make[2]: *** [arch/sh/kernel/time.o] Error 1
This trivial fix gets it working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20090824223239.GB20832@linux-sh.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the way in which "multi-evt" interrups are handled.
The intc_evt2irq_table and related intc_evt2irq() have been removed and
the "redirecting" handler is installed for the coupled interrupts.
Thanks to that the do_IRQ() function don't have to use another level
of indirection for all the interrupts...
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sys_cacheflush should return with EINVAL if the cache parameter is not
one of ICACHE, DCACHE or BCACHE.
So, we need to include 0 in the first check.
It also adds the three definitions above as wrapper of the existent macros.
PS: ltp cacheflush01 test now passes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Change the method used to flush the cache in write-through mode to
avoid corrupted data being written back to memory.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow peripherals before the start of RAM to be remapped.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It is possible for the CPU to re-enable it's interrupt block bit
before the write to the interrupt controller has actually masked out
the external interupt at the controller. We get around this by
reading back from the interrupt controller which will ensure the
write has happened.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adds a system call to allow user code to flush code from the cache.
You can use instructions for the data side, but the iside can
only be done by a flush ROM which really only works with a direct
mapped cache. The later SH4's have 2 way Iside, so this call allows
a portable way to flush the cache.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is a pure documentation, to try to explain why the cache flushing code
for the SH4 is implemented the way it is.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Optimise memcpy_to/fromio. This is used extensivly by MTD, so is a
worthwhile performance gain. The main savings come from not repeatedly
calling readl/writel, and doing word instead of byte at a time
transfers. Also using "movca.l" on SH4 gives a small performance win.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
After performing the port2addr conversion, and checking that the data is
correctly aligned, simply call __raw_readsX/writesX. These have already been
optimised.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Reading from the ROM is not a good idea as it could disturb some
flash operation that it is in progress.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The SH instruction set has several instructions which accept an 8 bit
immediate operand. For logical instructions this operand is zero extended,
for arithmetic instructions the operand is sign extended. After adding an
option to the assembler to check this, it was found that several pieces
of assembly code were assuming this behaviour, and in one case
getting it wrong.
So this patch explicitly sign extends any immediate operands, which makes
it obvious what is happening, and fixes the one case which got it wrong.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
So far kernel command line arguments could be passed in by a bootloader
or defined as CONFIG_CMDLINE, which completely overwriting the first one.
This change allows a developer to declare selected kernel parameters in
a kernel configuration (eg. project-specific defconfig), retaining
possibility of passing others by a bootloader.
The obvious examples of the first type are MTD partition or
bigphysarea-like region definitions, while "debug" option or network
configuration should be given by a bootloader or a JTAG boot script.
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patches will trigger a reboot using the watchdog
timer instead of double fault. Unlike the previous
method, this one actually works in 32 bit mode.
Reset should also be cleaner.
Signed-off-by: Jon Frosdick <jon.frosdick@st.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Save the VBR allowing GDB to dump full registers set but do not reload it
as soon as the kgdb_handle_exception is invoked.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The synopsys PCI cell used in the later STMicro chips requires code to
be run in order to do IO cycles, rather than just memory mapping the IO
space. Rather than extending the existing SH infrastructure to allow
this, use the GENERIC_IOMAP implmentation to save re-inventing the
wheel.
This set of changes allows the SH to be built with GENERIC_IOMAP
enabled, it just ifdef's out the functions provided by the GENERIC_IOMAP
implementation, and provides a few required missing functions.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
GCC does not issue unwind information for function epilogues.
Unfortunately we can catch a signal during an epilogue. The signal
handler writes the current context and signal return code onto the stack
overwriting previous contents. During unwinding, libgcc can try to
restore registers from the stack and restores corrupted ones. This can
lead to segmentation, misaligned access and sigbus faults.
For example, consider the following code:
mov.l r12,@-r15
mov.l r14,@-r15
sts.l pr,@-r15
mov r15,r14
<do stuff>
mov r14, r15
lds.l @r15+, pr
<<< SIGNAL HERE
mov.l @r15+, r14
mov.l @r15+, r12
rts
Unwind is aware that pr was pushed to stack in prolog, so tries to
restore it. Unfortunately it restores the last word of the signal
handler code placed on the stack by the kernel.
This patch tries to avoid the problem by adding a guard region on the
stack between where the function pushes data and where the signal handler
pushes its return code. We probably don't see this problem often because
exception handling unwinding in an epilogue only occurs due to a pthread
cancel signal. Also the kernel signal stack handler alignment of 8 bytes
could hide the occurance of this problem sometimes as the stack may not
be trampled at a particular required word.
This is not guaranteed to always work. It relies on a frame pointer
existing for the function (so it can get the correct sp value) which is
not always the case for the SH4.
Modifications will also be made to libgcc for the case where there is no
fp.
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a few problems with the existing code in do_address_error().
a) the variable used to printk()d the offending instruction wasn't
initialized correctly. This is a fix to bug 5727
b) behaviour for CONFIG_CPU_SH2A wasn't correct
c) the 'ignore address error' behaviour didn't update the PC, causing an
infinite loop.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch brings the SH4 misaligned trap handler in line with what
happens on ARM:
Add a /proc/cpu/alignment which can be read from to get alignment
trap statistics and written to to influence the behaviour of the
alignment trap handling. The value to write is a bitfield, which
has the following meaning: 1 warn, 2 fixup, 4 signal
In addition, we add a /proc/cpu/kernel_alignment, to enable or
disable warnings in case of kernel code causing alignment errors.
Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure we see messages about unaligned access fixups
every now and then. Else especially userspace apps suffering from
bad programming won't ever be noticed...
Signed-off by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The Runtime PM patch for UIO driver implements coarse grained
dynamic power management for UIO devices. With that patch in
place we can get rid of the static clock configuration. Which
in turn makes it possible for cpuidle to enter deeper sleep.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the Runtime PM driver changes in place, we must have
Runtime PM support in place. Otherwise there is no way to
enable clocks to the Runtime PM enabled hardware blocks.
This patch makes Runtime PM mandatory on SuperH Mobile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The runtime PM for SH-Mobile code had platform_bus_notify() as __devinit,
which is rather bogus. Kill off the annotation, which subsequently
silences the section mismatch warnings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V3 of the SuperH Mobile Runtime PM platform bus
implentation matching Rafael's Runtime PM v16.
The code gets invoked from the SuperH specific Runtime PM
platform bus functions that override the weak symbols for:
- platform_pm_runtime_suspend()
- platform_pm_runtime_resume()
- platform_pm_runtime_idle()
This Runtime PM implementation performs two levels of power
management. At the time of platform bus runtime suspend the
clock to the device is stopped instantly. Later on if all
devices within the power domain has their clocks stopped
then the device driver ->runtime_suspend() callbacks are
used to save hardware register state for each device.
Device driver ->runtime_suspend() calls are scheduled from
cpuidle context using platform_pm_runtime_suspend_idle().
When all devices have been fully suspended the processor
is allowed to enter deep sleep from cpuidle.
The runtime resume operation turns on clocks and also
restores registers if needed. It is worth noting that the
devices start in a suspended state and the device driver
is responsible for calling runtime resume before accessing
the actual hardware.
In this particular platform bus implementation runtime
resume is not allowed from interrupt context. Runtime
suspend is however allowed from interrupt context as
long as the synchronous functions are avoided.
[ updated for v17 -- PFM. ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The CIE and FDE structs are big enough and accessed regularly enough in
certain configurations to make cacheline alignment useful.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh64 does not yet support GENERIC_BUG, but still wants unwinder support.
Alias UNWINDER_BUG and UNWINDER_BUG_ON to their BUG counterparts until
the conversion to GENERIC_BUG is completed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This simplifies the unwinder trap handling, dropping the use of the
special trapa vector and simply piggybacking on top of the BUG support. A
new BUGFLAG_UNWINDER is added for flagging the unwinder fault, before
continuing on with regular BUG dispatch.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If the oprofile code is built as a module, unwind_stack() as used by the
oprofile backtrace code is not available, causing build breakage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allow a DWARF register to have an undefined value. When applied to the
DWARF return address register this lets lets us label a function as
having no direct caller, e.g. kernel_thread_helper().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The 'end' member of struct dwarf_fde denotes one byte past the end of
the CFA instruction stream for an FDE. The value of 'end' was being
calcualted incorrectly, it was being set too high. This resulted in
dwarf_cfa_execute_insns() interpreting data past the end of valid
instructions, thus causing all sorts of weird crashes.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
When CONFIG_DWARF_UNWINDER is enabled setup r14 in handle_interrupt, so
that we can figure out what function was running when we were
interrupted.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
We can't assume that if we execute the unwinder code and the unwinder
was already running that it has faulted. Clearly two kernel threads can
invoke the unwinder at the same time and may be running simultaneously.
The previous approach used BUG() and BUG_ON() in the unwinder code to
detect whether the unwinder was incapable of unwinding the stack, and
that the next available unwinder should be used instead. A better
approach is to explicitly invoke a trap handler to switch unwinders when
the current unwinder cannot continue.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The handling of DW_CFA_val_offset ops was incorrectly using the
DWARF_REG_OFFSET flag but the register's value cannot be calculated
using the DWARF_REG_OFFSET method. Create a new flag to indicate that a
different method must be used to calculate the register's value even
though there is no implementation for DWARF_VAL_OFFSET yet; it's mainly
just a place holder.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Plug a memory leak in dwarf_unwinder_dump() where we didn't free the
memory that we had previously allocated for the DWARF frames and DWARF
registers.
Now is also a opportune time to implement our own mempool and kmem
cache. It's a good idea to have a certain number of frame and register
objects in reserve at all times, so that we are guaranteed to have our
allocation satisfied even when memory is scarce. Since we have pools to
allocate from we can implement the registers for each frame as a linked
list as opposed to a sparsely populated array. Whilst it's true that the
lookup time for a linked list is larger than for arrays, there's only
usually a maximum of 8 registers per frame. So the overhead isn't that
much of a concern.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
on_each_cpu() takes care of IRQ and preempt handling, the localized
handling in each of the called functions can be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of rework for making the cache flushers SMP-aware. The
function pointer-based flushers are renamed to local variants with the
exported interface being commonly implemented and wrapping as necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All CPU-specific overloads are done at runtime now, so this common header
can go away and simply be folded back in to asm/ version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the kfr2r09 defconfig with support for LCDC and USB gadget.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add romImage defconfig for the kfr2r09 board. This defconfig
should be used to build the kernel based boot loader.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a P1 jump to the the kfr2r09 romimage code. With this
patch applied the initial zImage assembly code will run
with instruction cache enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add instruction cache and TLB invalidation code for the
the kfr2r09 romimage target.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When get_mmu_context() runs out of new ASIDs it flushes the TLB and
wraps around. Despite the fact the ASIDs are tracked per-CPU, a global
TLB flush was being used. Switch this over to a local one, as matches
the intent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the only board that presently supports this rtc, so make sure it
is enabled by default to get some build coverage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:
- In the DSP restore case a0 needs to be popped off before a0g,
or the value of a0g is clobbered by the MSB of a0 in the case
of sign extension.
- Beyond that, the save and restore orders were out of sync,
so this fixes that up as well. At the same time, we switch over
to using movs.l for both the save and restore of the general DSP
registers as opposed to using sts.l (which was initially put in
place to work around a bug in ancient binutils versions which
the kernel no longer supports).
Reported-by: Chee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-tip can't be bothered keeping interfaces stable long enough for anyone
to use them without having their builds broken without notification, so
just ifdef around the problematic symbols until the new interfaces become
available upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port YC301 on the KFR2R09 board.
The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.
This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the clockevents broadcasting code as detailed in commit
ee348d5a1d ("[ARM] realview: fix broadcast
tick support"). This saves us from having to do strange ordering things
with the broadcast clockevent device, relying on the rating instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the build when caches are disabled, by linking in all of
the cache routines directly. This paves the way for splitting out
separate I and D cache disabling, similar to what sh64 had, and which
we want for SH-X3 anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While most platforms implement LED banks in sets of 8/16/32, some use
different configurations. This adds a LED mask to the heartbeat platform
data to allow platforms to constrain the bitmap, which is otherwise
derived from the register size.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the FRQCRA.IFC divisor values for SH7724. Despite
not being initially documented, the / 3 mode is also support for the IFC
division.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
FLLFRQ setting is needed to use correct PLL clock for kfr2409.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
save_regs contains an SR modification without an irqflags annotation,
which resulted in a missing TRACE_IRQS_OFF in the interrupt exception
path on SH-3/SH4.
I've also moved the TRACE_IRQS_OFF/ON annotation when returning from the
interrupt to just before we call __restore_all. This seems like the most
logical place to put this because the annotation is for when we restore
the SR register so we should delay the annotation until as last as
possible.
We were also missing a TRACE_IRQS_OFF in resume_kernel when
CONFIG_PREEMPT is enabled.
The end result is that this fixes up the lockdep engine debugging support
with CONFIG_PREEMPT enabled on all SH-3/4 parts.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds "SuperH Mobile Standby Mode [SF]" to the list
of cpuidle sleep modes. If the software latency requirements
from cpuidle are met together with fulfilled hardware
requirements then deep sleep modes can be entered.
Tested on sh7722 and sh7724 with "Sleep Mode", "Sleep Mode + SF"
and "Software Standby Mode + SF" together with a multimedia
work load and flood ping without packet drop.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the exception handling in the sleep code
for SuperH Mobile. With the patch applied the sleep code
always rewrites the VBR and resumes from the exception vector,
re-initializes hardware and jumps straight to the original
interrupt vector.
Tested on sh7722 and sh7724 with "Sleep Mode", "Sleep Mode + SF"
and "Software Standby Mode + SF" with CONFIG_SUSPEND.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the initialization over to an early_initcall(). This fixes up
some lockdep interaction issues. At the same time, kill off some
superfluous locking in the init path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Also, remove the "fix" to DW_CFA_def_cfa_register where we reset the
frame's cfa_offset to 0. This action is incorrect when handling
DW_CFA_def_cfa_register as the DWARF spec specifically states that the
previous contents of cfa_offset should be used with the new
register. The reason that I thought cfa_offset should be reset to 0 was
because it was being assigned a bogus value prior to executing the
DW_CFA_def_cfa_register op. It turns out that the bogus cfa_offset value
came from interpreting .cfi_escape pseudo-ops (those used by the GNU
extensions) as CFA_DW_def_cfa ops.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The previous hack for calculating the return address for the first frame
we unwind (dwarf_unwinder_dump) didn't always work. The problem was that
it assumed once it read the rule for calculating the return address,
there would be no new rules for calculating it. This isn't true because
the way in which the CFA is calculated can change as you progress
through a function and the return address is figured out using the
CFA. Therefore, the way to calculate the return address can change.
So, instead of using some offset from the beginning of
dwarf_unwind_stack which is just a flakey approach, and instead of
executing instructions from the FDE until the return address is setup,
we now figure out the pc in dwarf_unwind_stack() just before we call
dwarf_cfa_execute_insns().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Now that the SH-5 code is more or less behaving with the new cacheflush
interface, wire up the initialization code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These will be handled through the shared cache interface instead, and
they are presently undefined anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The caches enabled case needs more work, but is presently broken
regardless, so this can be done incrementally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The persistent clock of some architectures (e.g. s390) have a
better granularity than seconds. To reduce the delta between the
host clock and the guest clock in a virtualized system change the
read_persistent_clock function to return a struct timespec.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134811.013873340@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is superfluous, as the default CPU type and family are already
established by the initial cpuinfo definition. Given that we are still
able to probe for the CPU family even if we are not able to detect the
subtype, it's preferable to let the probing code fill out what it can and
leave the rest.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch simply adds LCDC hwblk_id data for the kfr2r09 board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.
Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.
Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.
Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This paves the way for allowing individual CPUs to overload the
individual flushing routines that they care about without having to
depend on weak aliases. SH-4 is converted over initially, as it wires
up pretty much everything. The majority of the other CPUs will simply use
the default no-op implementation with their own region flushers wired up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We use flush_cache_page() outright in copy_to_user_page(), and nothing
else needs it, so just kill it off. SH-5 still defines its own version,
but that too will go away in the same fashion once it converts over.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the flush_dcache_mmap_lock()/flush_dcache_mmap_unlock()
definitions are identical across all CPUs, so just provide them
generically in asm/cacheflush.h.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_dcache_all() is used internally by the SH-4 cache code, it is not
part of the exported cache API, so make it static and don't export it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This migrates the alias computation and printing of probed cache
parameters from the SH-4 code to the shared cpu_cache_init().
This permits other platforms with aliases to make use of the same
probe logic without having to roll their own, and also produces
consistent output regardless of platform.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a central point for CPU cache initialization routines.
This replaces the antiquated p3_cache_init() method, which the vast
majority of CPUs never cared about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a family member to struct sh_cpuinfo, which allows us to fall
back more on the probe routines to work out what sort of subtype we are
running on. This will be used by the CPU cache initialization code in
order to first do family-level initialization, followed by subtype-level
optimizations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were previous littered around tlb-nommu.c and pg-nommu.c, though at
this point there are more stubs than are strictly TLB or page op related,
so just consolidate them in a single nommu.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of reorganizing for allowing nommu to use the new
and generic cache.c, no functional changes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This builds in the newly created cache.c (renamed from pg-mmu.c) for both
MMU and NOMMU configurations. The kmap_coherent() stubs and alias
information recorded by each CPU family takes care of doing the right
thing while enabling the code to be commonly shared.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in kmap_coherent() for the non-SH4 cases to permit the
pg-mmu.c bits to be used generically across all CPUs. SH-5 is still in
the TODO state, but will move over to fixmap and the generic interface
gradually.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This kills off the ifdef from kmap_coherent_init() and just bails if
there are no cache aliases. This permits the kmap coherent code to be
used on other CPUs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The way that the CFA is calculated can change as we progress through a
function. If we see a DW_CFA_def_cfa_register op we need to reset the
frame's cfa_offset value which may have been previously setup.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements EXPMASK initialization code for SH-4A parts, where it is
possible to disable compat features that will go away in newer cores.
Presently this includes disabling support for non-nop instructions in the
rte delay slot, as well as a sleep instruction being placed in a delay
slot (neither of which the kernel does any longer). As a result of this,
any future offenders will have illegal slot exceptions generated for
them.
Associative writes for the memory-mapped cache array are still left
enabled, until such a point that special cache operations for SH-4A are
provided to move off of the current (and rather dated) SH-4 versions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Future SH parts do not support any instruction but a nop in the rte delay
slot, so make the change for all offending parts. SH-5 is excluded from
this, and already has its own set of restrictions with regards to rte
delay slot handling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This only bothers with the TLB entry flush in the case of the initial
page write exception, as it is unecessary in the case of the load/store
exceptions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a bit of rework to have the TLB protection violations skip the
TLB miss fastpath and go directly in to do_page_fault(), as these require
slow path handling.
Based on an earlier patch by SUGIOKA Toshinobu.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This optimizes for the cases when a CPU does not yet have a valid ASID
context associated with it, as in this case there is no work for any of
flush_cache_mm()/flush_cache_page()/flush_cache_range() to do. Based on
the the MIPS implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now with all of the prep work out of the way, kill off the SH-5 variants
and use the SH-4 version directly. This also takes advantage of the
unrolling that was previously done for the new version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in some register alignment helpers for the shared flushers,
allowing them to also be used on SH-5. The main rationale here is that
in the SH-5 case we have a variable ABI, where the pointer size may not
equal the register width. This register extension is taken care of by
the SH-5 code already today, and is otherwise unused on the SH-4 code.
This combines the two and allows us to kill off the SH-5 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This inserts a ULONG_MAX entry at the end of the valid entries in the
stack trace buffer so the default code doesn't need to scan to the end of
available slots. This also makes the trace buffer termination behaviour
consistent with the other architectures.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This flags the default unwinder as reliable, as it tends to be reliable
enough for the purposes of the stacktrace buffer. We leave the unreliable
cases for the unwind methods that we know to be completely broken.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adopts the reliability checks from the x86 stacktrace code so known
bad addresses are not recorded in the stack trace buffer.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
save_stack_trace_tsk() and friends can be called from atomic context (as
triggered by latencytop), and subsequently hit two problematic allocation
points that were using GFP_KERNEL (these were dwarf_unwind_stack() and
dwarf_frame_alloc_regs()). Convert these over to GFP_ATOMIC and get
latencytop working with the DWARF unwinder.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Conflicts:
arch/sparc/kernel/smp_64.c
arch/x86/kernel/cpu/perf_counter.c
arch/x86/kernel/setup_percpu.c
drivers/cpufreq/cpufreq_ondemand.c
mm/percpu.c
Conflicts in core and arch percpu codes are mostly from commit
ed78e1e078dd44249f88b1dd8c76dafb39567161 which substituted many
num_possible_cpus() with nr_cpu_ids. As for-next branch has moved all
the first chunk allocators into mm/percpu.c, the changes are moved
from arch code to mm/percpu.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Trying to figure out the best value for DWARF_ARCH_UNWIND_OFFSET is
tricky at best. Various things can change the size (and offset from the
beginning of the function) of the prologue. Notably, turning on ftrace
adds calls to mcount at the beginning of functions, thereby pushing the
prologue further into the function.
So replace DWARF_ARCH_UNWIND_OFFSET with some code that continues to
execute CFA instructions until the value of return address register is
defined. This is safe to do because we know that the return address must
have been pushed onto the frame before our first function call; we just
can't figure out where at compile-time.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The destination address might be unaligned, so set it with
put_unaligned() for safety. This restores the previous behaviour, albeit
through the proper API.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was using internal symbols for unaligned accesses, bypassing the
exposed interface for variable sized safe accesses. This converts all of
the __get_unaligned_cpuXX() users over to get_unaligned() directly,
relying on the cast to select the proper internal routine.
Additionally, the __put_unaligned_cpuXX() case is superfluous given that
the destination address is aligned in all of the current cases, so just
drop that outright.
Furthermore, this switches to the asm/unaligned.h header instead of the
asm-generic version, which was silently bypassing the SH-4A optimized
unaligned ops.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Annotate various assembly code paths with CFI assembler directives so
that DWARF unwind info is available for the unwinder.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In order to use DWARF unwinder info the frame register has to contain a
valid value. Whilst GCC takes care of this for C code, we have to do it
ourselves for assembly.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is a first cut at a generic DWARF unwinder for the kernel. It's
still lacking DWARF64 support and the DWARF expression support hasn't
been tested very well but it is generating proper stacktraces on SH for
WARN_ON() and NULL dereferences.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of implementing our own stack unwinder via dump_trace() we
should use the new stack unwinder API because it is more modular. This
change allows us to decouple the interface for generating stacktraces
from the implementation of a stack unwinder.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Provide an interface for registering stack unwinders, where each
unwinder is given a rating that describes its accuracy and
complexity. The more accurate an unwinder is, the more complex it is.
If a the current stack unwinder faults, then the stack unwinder with the
next highest accuracy will be used in its place (provided one is
available). For example, this allows unwinders, such as the DWARF
unwinder, to liberally sprinkle BUG()s to catch badly formed DWARF debug
info.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Copy the stacktrace ops code from x86 and provide a central function for
use by functions that need to dump a callstack.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves the Migo-R specific header file from
mach-common/ into mach-migor/ and removes unused cruft.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch moves all the romImage related header files into
the mach/ directory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for LED9, LED10 and LED11 on
the Solution Engine 7724 board. If CONFIG_PM is enabled
then these LEDs are used to show the hardware sleep
mode used by the processor. Useful to debug cpuidle.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the NAND flash chip
attached to CS4 on the KFR2R09 board. The device is
driven by the platform device driver "onenand-flash".
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the WQVGA LCD display used by
the KFR2R09 board. The LCD module is a TX07D34VM0AAA made
by Hitachi, and this module is made up by a R61517 chip
together with a 240x400 pixel display. The screen is
attached to the SuperH Mobile LCDC using a 18-bit SYS bus.
The register settings used by the SYS panel setup code are
based on an out-of-tree driver which apart from duplicating
all LCDC driver code and writing to non-existing hardware
registers also never was posted for upstream merge.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of unrolling for the SH-4 region flushers.
Based on an earlier patch by SUGIOKA Toshinobu.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the SH-4 __flush_xxx_region() functions and defines them
as weak symbols. This allows us to provide optimized versions without
having to ifdef cache-sh4.c to death.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This can use the now generic clear_page() implementation, which is backed
by the sh64 optimized memset routine. This also fixes up the case where
PAGE_SIZE != 4kB.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates all of the NEFF-based sign extension for SH-5.
In the future the other SH code will need to make use of this as well,
so make it generic in preparation for more 32/64 consolidation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a __flush_anon_page() that handles both the aliasing and
non-aliasing cases. This fixes up some crashes with heavy
get_user_pages() users.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in a BUG_ON() in kmap_coherent() for PG_dcache_dirty pages
to catch when things go horribly wrong. Copied from the MIPS
implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7724 board specific
on-chip sh7724 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to kfr2r09 board specific on-chip sh7724
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to AP325RXA board specific on-chip sh7723
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7722 board specific
on-chip sh7722 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Migo-R board specific on-chip sh7722
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These patches extend struct platform device data for a bunch of
SuperH Mobile processors and embedded boards. The patches simply
add hardware block ids to on-chip platform devices. Platform
devices off chip (such as external ethernet controllers or flash
chips) are left out which gives them a special case hardware block
id of zero.
Upcoming Runtime PM code will make use of the hardware block id
to group devices together. The hardware block id can also be used
to extend the SuperH Mobile clock framework implementation.
This series of patches depend on the following:
"Driver Core: Add platform device arch data V3".
This patch adds a hwblk_id member to struct pdev_archdata. This member
should be used to point out on-chip hardware block id.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was no big meaning in the support of SVGA,
but 720p support is necessary for ms7724se board.
So, this patch support 720p instead of SVGA.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the unused MSTPCRn register definitions
from the SuperH Mobile code for sh7722, sh7723 and sh7724.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds early printk support for SH770x (tested on SH7709 based hp6xx).
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is romImage support for the kfr2r09 board V2.
The partner-jet-setup.txt file is converted into assembly code
which becomes the first code to execute from the reset vector.
The file partner-jet-setup.txt can also be used to setup
the hardware using a JTAG debugger so booting from RAM can
be done without burning the code to flash.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains support for the romImage build target V2.
The resulting romImage file should be burned to rom
or flash and could be used as small boot loader.
Board code should keep their setup code in the file
romimage.h located in their mach include directory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This cleans up the irqflags tracing code quite a bit and ties it
in to various missing callsites that caused an imbalance when
CONFIG_PROVE_LOCKING was enabled.
Previously this was catching on:
987 #ifdef CONFIG_PROVE_LOCKING
988 DEBUG_LOCKS_WARN_ON(!p->hardirqs_enabled);
989 DEBUG_LOCKS_WARN_ON(!p->softirqs_enabled);
990 #endif
991 retval = -EAGAIN;
with hardirqs being doubly enabled, and subsequently bailing out
with the following call trace:
Call trace:
[<88035224>] __lock_acquire+0x616/0x6a6
[<88015a8c>] do_fork+0xf8/0x2b0
[<880331ec>] trace_hardirqs_on_caller+0xd4/0x114
[<88241074>] _spin_unlock_irq+0x20/0x64
[<88035224>] __lock_acquire+0x616/0x6a6
[<8800386c>] kernel_thread+0x48/0x70
[<88024ecc>] ____call_usermodehelper+0x0/0x110
[<88024ecc>] ____call_usermodehelper+0x0/0x110
[<88003894>] kernel_thread_helper+0x0/0x14
[<88024bac>] __call_usermodehelper+0x38/0x70
[<88025dc0>] worker_thread+0x150/0x274
[<88035b9c>] lock_release+0x0/0x198
[<88024b74>] __call_usermodehelper+0x0/0x70
[<88028cf0>] autoremove_wake_function+0x0/0x30
[<88028bf2>] kthread+0x3e/0x70
[<88025c70>] worker_thread+0x0/0x274
[<8800389c>] kernel_thread_helper+0x8/0x14
[<88028bb4>] kthread+0x0/0x70
[<88003894>] kernel_thread_helper+0x0/0x14
Reported-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 1d29ebebcb.
Bumping up the earlytimer initialization causes IRQs to be enabled too
early, which blows up lockdep:
...
NR_IRQS:256 nr_irqs:256
------------[ cut here ]------------
Badness at kernel/lockdep.c:2128
Pid : 0, Comm: swapper
CPU : 0 Not tainted (2.6.31-rc3-00205-g3ed6e12-dirty #2443)
PC is at trace_hardirqs_on_caller+0x48/0x10c
PR is at trace_hardirqs_on_caller+0x3c/0x10c
...
Revert it back to late_time_init time, which fixes up lockdep.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The TLB miss fast-path presently calls in to update_mmu_cache() to
set up the entry, and does so with a NULL vma. Check for vma validity
in the __update_tlb() ptrace checks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out a separate __update_cache()/__update_tlb() for
update_mmu_cache() to wrap in to. This lets us share the common
__update_cache() bits while keeping special __update_tlb() handling
broken out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Those definitions are already provided by asm-generic
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the SH-4 page clear/copy ops are generic, they can be used for
all platforms with CONFIG_MMU=y. SH-5 remains the odd one out, but it too
will gradually be converted over to using this interface.
SH-3 platforms which do not contain aliases will see no impact from this
change, while aliasing SH-3 platforms will get the same interface as
SH-4.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wires up clear_user_highpage() on SH-4 and subsequently converts the
SH7705 32kB cache mode over to using it. Now that the SH-4 implementation
handles all of the dcache purging directly in the aliasing case, there is
no need to do this in the default clear_page() implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a defconfig and a mach-types entry for
the kfr2r09 board.
At this point only a few devices like SCIF, KEYSC and
NOR Flash are supported together with sh7724 devices
such as IIC0, IIC1 and the multimedia blocks exported
via UIO.
Kexec is supported, but booting from flash is not (yet).
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds KEYSC keypad support to the kfr2r09 board.
The keys driven by the sh7724 on-chip KEYSC block are
described as a platform device and platform data for
the sh_keysc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds NOR flash support to the kfr2r09 board.
NOR flash support is added by describing the NOR flash
chip hooked up to CS0 as platform device data for the
physmap-flash MTD driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the m66592-udc driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_BUILT_IN_M66592 ugliness.
This makes the code cleaner and also allows us to support
both external and internal m66592 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip m66592 without modifying the Kconfig.
The patch adds a m66592 header file for platform data
and ties in platform data to the existing m66592 devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This inverts the delayed dcache flush a bit to be more in line with other
platforms. At the same time this also gives us the ability to do some
more optimizations and cleanup. Now that the update_mmu_cache() callsite
only tests for the bit, the implementation can gradually be split out and
made generic, rather than relying on special implementations for each of
the peculiar CPU types.
SH7705 in 32kB mode and SH-4 still need slightly different handling, but
this is something that can remain isolated in the varying page copy/clear
routines. On top of that, SH-X3 is dcache coherent, so there is no need
to bother with any of these tests in the PTEAEX version of
update_mmu_cache(), so we kill that off too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Allocate one of the unused PTE bits for _PAGE_SPECIAL directly. This is
prep work for fast gup and the zero page revival.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This builds on the bzip2/lzma zImage support change and wires it up for
uImages. Based on the blackfin implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the r8a66597-hcd driver to use the on_chip flag
from platform data to enable on chip behaviour instead
of relying on CONFIG_SUPERH_ON_CHIP_R8A66597 ugliness.
This makes the code cleaner and also allows us to support
both external and internal r8a66597 with the same kernel.
It also makes the Kconfig part more future proof since
we with this patch can add support for new processors
with on-chip r8a66597 without modifying the Kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the SuperH hwblk code to support more than one counter.
Contains ground work for the future Runtime PM implementation.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The last commit changed the behaviour on kernel faults when we were
doing something other than syncing the page tables. vmalloc_sync_one()
needs to return NULL if the page tables are up to date, because the
reason for the fault was not a missing/inconsitent page table entry. By
returning NULL if the page tables are sync'd we signal to the calling
function that further work must be done to resolve this fault.
Also, remove the superfluous __va() around the first argument to
vmalloc_sync_one(). The value of pgd_k is already a virtual address and
using it wth __va() causes a NULL dereference.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This brings the zImage handling in to the current century, in preparation
for handling the other compression types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the STACK_CHECK() code is called in to multiple times, although
it's only necessary from the mcount entry. The code still attempts to
treat the nop case as an ftrace path resulting in superfluous code flow
for the case where ftrace is disabled. And finally, this also fixes up
references to a few undefined symbols when FUNCTION_TRACER=n.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the closest reference to function_trace_stop is within a
CONFIG_STACK_DEBUG block. When this is turned off, the build bails out
with a pcrel too far error. Reorder things a bit to handle the various
combinations.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The function prototype for mcount is not defined if we are not building
with ftrace support enabled, so use DECLARE_EXPORT() to stub one in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
STACK_DEBUG ties in to mcount in order to do function-granular stack
overflow checks as opposed to lazily checking from IRQ context. As the
default is nohz, the frequency of overflow checking is too irregular to
catch much useful information, and so the mcount approach employed by
sparc64 is adopted instead.
This kills off the old check entirely from the do_IRQ() path and now
adopts CONFIG_MCOUNT instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a general CONFIG_MCOUNT in order to permit mcount generation
without ftrace support. This is primarily for allowing platforms to
enable aggressive stack overflow checking without having to enable ftrace
support. Based on the sparc64 implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Annotate __switch_to() so that the function graph tracer does not try to
trace it. Use __notrace_funcgraph, as opposed to notrace, so that other
tracers can continue to trace __switch_to().
The reason that we don't want to trace __switch_to() with the function
graph tracer is because of how the return address stack in task_struct
is implemented. When we enter __switch_to we store the real return
address on prev's ret_stack. When we return from __switch_to() we've
patched the return address on the kernel stack to be
return_to_handler. Calling return_to_handler we do,
-> ftrace_return_to_handler()
-> ftrace_pop_return_ftrace()
Which tries to pop the real return address from current->ret_stack. The
problem being that we stored the return address on prev->ret_stack, but
current now points to next, and next->ret_stack doesn't contain the
correct return address (and is possibly even empty).
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add both dynamic and static function graph tracer support for sh.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable kernel stack checking code in both the dynamic ftrace and mcount
code paths. Check the stack to see if it's overflowing and make sure
that the stack pointer contains an address that's either in init_stack
or after the bss.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts the sh architecture to use the new linker script
macros in include/asm-generic/vmlinux.lds.h.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Discarded sections in different archs share some commonality but have
considerable differences. This led to linker script for each arch
implementing its own /DISCARD/ definition, which makes maintaining
tedious and adding new entries error-prone.
This patch makes all linker scripts to move discard definitions to the
end of the linker script and use the common DISCARDS macro. As ld
uses the first matching section definition, archs can include default
discarded sections by including them earlier in the linker script.
ia64 is notable because it first throws away some ia64 specific
subsections and then include the rest of the sections into the final
image, so those sections must be discarded before the inclusion.
defconfig compile tested for x86, x86-64, powerpc, powerpc64, ia64,
alpha, sparc, sparc64 and s390. Michal Simek tested microblaze.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Michal Simek <monstr@monstr.eu>
Cc: linux-arch@vger.kernel.org
Cc: Michal Simek <monstr@monstr.eu>
Cc: microblaze-uclinux@itee.uq.edu.au
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Tony Luck <tony.luck@intel.com>
Now that I've added TIF_SYSCALL_FTRACE the thread flags do not fit into
a single byte any more. Code testing them now needs to be aware of the
upper and lower bytes.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable HAVE_FUNCTION_TRACE_MCOUNT_TEST and test the value of
function_trace_stop from our assembly code as opposed to using the
generic C function. This should optimise our mcount/ftrace code path.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It seems that MCOUNT_INSN_OFFSET was calculating the distance between
the wrong functions. The value that should have actually been computed
is the distance between ftrace_call and ftrace_stub. I discovered this
when I added some code to ftrace_caller.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rewrites the vmalloc fault handling as per x86, which subsequently
allows for easy future tie-in for vmalloc_sync_all().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
