This patch (as1458) fixes a problem affecting ultra-reliable systems:
When hardware failover of an EHCI controller occurs, the data
structures do not get released correctly. This is because the routine
responsible for removing unused QHs from the async schedule assumes
the controller is running properly (the frame counter is used in
determining how long the QH has been idle) -- but when a failover
causes the controller to be electronically disconnected from the PCI
bus, obviously it stops running.
The solution is simple: Allow scan_async() to remove a QH from the
async schedule if it has been idle for long enough _or_ if the
controller is stopped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-Tested-by: Dan Duval <dan.duval@stratus.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During processing of bunch of eem frames if "echo" command is found
skb is cloned and the cloned version should be used to send reply.
Unfortunately, the data of the original skb were actually used and
the cloned skb is never freed.
Using the cloned skb and freeing the skb in the completion callback
for usb request.
Signed-off-by: Yauheni Kaliuta <yauheni.kaliuta@nokia.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added new ProdutIds for two devices from CTI GmbH Leipzig.
Signed-off-by: Christian Simon <simon@swine.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Because the disconnect function in the composite driver will call spin_lock,
this driver has to call spin_unlock before calling driver->disconnet().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig
Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ep_read() acquires data->lock mutex in get_ready_ep() and releases it on
all paths except for one: when usb_endpoint_xfer_isoc() failed. The
patch adds mutex_unlock(&data->lock) at that path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix printk format build warning and grammar typo on same line.
drivers/usb/host/isp1760-hcd.c:300: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-greg' of git://gitorious.org/usb/usb:
USB: musb: blackfin: work around anomaly 05000450
usb: musb: Fix the crash issue during reboot
usb: musb: gadget: check the correct list_head
usb: musb: temporarily make it bool
USB: musb: dereferencing an iomem pointer
USB: musb: silence printk format warning
USB: musb: using 0 instead of NULL
USB: musb: add missing unlock in cppi_interrupt()
usb: musb: ux500: copy dma mask from platform device to musb device
usb: musb: clear AUTOSET while clearing DMAENAB
In the function blk_register_queue(), var _dev_ is already assigned by
disk_to_dev().So use it directly instead of calling disk_to_dev() again.
Signed-off-by: Liu Yuan <tailai.ly@taobao.com>
Modified by me to delete an empty line in the same function while
in there anyway.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/avr32-2.6:
avr32: add ATAG_BOARDINFO
don't check platform_get_irq's return value against zero
avr32: init cannot ignore signals sent by force_sig_info()
avr32: fix deadlock when reading clock list in debugfs
avr32: Fix .size directive for cpu_enter_idle
avr32: At32ap: pio fix typo "))" on gpio_irq_unmask prototype
fix the wrong argument of the functions definition
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
Revert "i915: restore only the mode of this driver on lastclose"
Revert "ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set."
i915: select VIDEO_OUTPUT_CONTROL for ACPI_VIDEO
drm/radeon/kms: properly program vddci on evergreen+
drm/radeon/kms: add voltage type to atom set voltage function
drm/radeon/kms: fix pcie_p callbacks on btc and cayman
drm/radeon/kms: fix suspend on rv530 asics
drm/radeon/kms: clean up gart dummy page handling
drm/radeon/kms: make radeon i2c put/get bytes less noisy
drm/radeon/kms: pll tweaks for rv6xx
drm/radeon: Fix KMS legacy backlight support if CONFIG_BACKLIGHT_CLASS_DEVICE=m.
radeon: Fix KMS CP writeback on big endian machines.
i915: restore only the mode of this driver on lastclose
drm/nvc0: improve vm flush function
drm/nv50-nvc0: remove some code that doesn't belong here
drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
drm/nouveau: quirk for XFX GT-240X-YA
drm/nv50-nvc0: work around an evo channel hang that some people see
drm/nouveau: implement init table opcode 0x5c
drm/nouveau: fix oops on unload with disabled LVDS panel
...
We really only want to unplug the pending IO when the process actually
goes to sleep. So move the test for flushing the plug up to the place
where we actually deactivate the task - where we have properly checked
for preemption and for the process really sleeping.
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 982134ba62 ("mm: avoid wrapping vm_pgoff in mremap()") fixed
the case of a expanding mapping causing vm_pgoff wrapping when you used
mremap. But there was another case where we expand mappings hiding in
plain sight: the automatic stack expansion.
This fixes that case too.
This one also found by Robert Święcki, using his nasty system call
fuzzer tool. Good job.
Reported-and-tested-by: Robert Święcki <robert@swiecki.net>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ATAG_BOARDINFO is intended to hand over the information
bd->bi_board_number from u-boot to the kernel.
This piece of information can be used to implement some kind of board
identification while booting the kernel. Therefore it is placed in .initdata
section and can be accessed via the new symbol board_number only while
initializing the kernel.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
platform_get_irq returns -ENXIO on failure, so !int_irq was probably
always true. Better use (int)int_irq <= 0. Note that a return value of
zero is still handled as error even though this could mean irq0.
This is a followup to 305b3228f9 that
changed the return value of platform_get_irq from 0 to -ENXIO on error.
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
We can delete the code that checks to see if we're sending an ignored
signal to init because force_sig_info() already handles this case.
force_sig_info() will kill init even if the signal handler is SIG_DFL
and the scenario described in the comment where init might "generate
the same exception over and over again" cannot occur (force_sig_info()
clears SIGNAL_UNKILLABLE to ensure that init will die).
Also, the use of is_global_init() is not correct in the multhreaded
case, as Oleg Nesterov explains,
"is_global_init() is not right in theory, /sbin/init can be
multithreaded. And, this doesn't cover the sub-namespace
inits... I'd suggest to check SIGNAL_UNKILLABLE, but looking
closer I think you can simply remove this code."
It seems this code was copied from arch/powerpc in March 2007 in commit
623b0355d5 "[AVR32] Clean up exception handling code"
but the code was deleted from arch/powerpc in November 2009 in commit
a0592d42fe "powerpc: kill the obsolete code under is_global_init()"
So catch up with powerpc and delete the bogus code.
Signed-off-by: Matt Fleming <matt.fleming@linux.intel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
When writing out /sys/kernel/debug/at32ap_clk, clock list lock is being
held while clk_get() is called. clk_get() attempts to take the same
lock, which results in deadlock. Introduce and call lock free version,
__clk_get(), instead.
Signed-off-by: Ole Henrik Jahren <olehenja@alumni.ntnu.no>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
gas used to accept (and ignore?) .size directives which referred to
undefined symbols, as this does. In binutils 2.21 these are treated
as errors.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
The functions of eic_chip's memebers use the wrong argument .
Signed-off-by: Wanlong Gao <wanlong.gao@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
When compiling UBIFS with CONFIG_UBIFS_FS_DEBUG not set,
gcc-4.5.2 generates a slew of "warning: statement with no effect"
on references to non-void functions defined as 0.
To avoid these warnings, replace #defines with dummy inline functions.
Artem: massage the patch a bit, also remove the duplicate
'dbg_check_lprops()' prototype.
Signed-off-by: Maksim Rayskiy <maksim.rayskiy@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
DMA mode 1 data corruption anomaly on Blackfin systems. This issue is
specific to the Blackfin silicon as the bug appears to be related to the
connection of the musb ip to the bus/dma fabric.
Data corruption when using USB DMA mode 1. (Issue manager 17-01-0105)
DMA mode 1 allows large size transfers to generate a single interrupt
at the end of the entire transfer. The transfer is split up in packets
of length specified in the Maximum Packet Size field for that endpoint.
If the transfer size is not an integer multiple of the Maximum Packet
Size, a short packet will be present at the end of the transfer.
Under certain conditions this packet may be corrupted in the USB FIFO.
Workaround:
Use DMA mode 1 to transfer (n* Maximum Packet Size) and schedule DMA
mode 0 to transfer the short packet.
As an example if your transfer size is 33168 bytes and Maximum Packet
Size equals 512, schedule [33168 - (33168 mod 512)] in DMA mode 1 and
the remainder (33168 mod 512) in DMA mode 0.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Cc: stable@kernel.org # v2.6.38
Signed-off-by: Felipe Balbi <balbi@ti.com>
"tx_ram" points to io memory. We can't dereference it directly. Sparse
complains about this: "drivers/usb/musb/cppi_dma.c:1205:25: warning:
dereference of noderef expression"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gcc gives the following warnings:
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_tx_segment’:
drivers/usb/musb/cppi_dma.c:600: warning: format ‘%x’ expects type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_rx_segment’:
drivers/usb/musb/cppi_dma.c:822: warning: format ‘%x’ expects type ‘unsigned int’, but argument 9 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_rx_scan’:
drivers/usb/musb/cppi_dma.c:1042: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c:1114: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 7 has type ‘dma_addr_t’
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them
to unsigned long long for printk().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes severe UBIFS bug: UBIFS oopses when we 'fsync()' an
file on R/O-mounter file-system. We (the UBIFS authors) incorrectly
thought that VFS would not propagate 'fsync()' down to the file-system
if it is read-only, but this is not the case.
It is easy to exploit this bug using the following simple perl script:
use strict;
use File::Sync qw(fsync sync);
die "File path is not specified" if not defined $ARGV[0];
my $path = $ARGV[0];
open FILE, "<", "$path" or die "Cannot open $path: $!";
fsync(\*FILE) or die "cannot fsync $path: $!";
close FILE or die "Cannot close $path: $!";
Thanks to Reuben Dowle <Reuben.Dowle@navico.com> for reporting about this
issue.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: Reuben Dowle <Reuben.Dowle@navico.com>
Cc: stable@kernel.org
Add a new EV_SYN code, SYN_DROPPED, to inform the client when input
events have been dropped from the evdev input buffer due to a
buffer overrun. The client should use this event as a hint to
reset its state or ignore all following events until the next
packet begins.
Signed-off-by: Jeff Brown <jeffbrown@android.com>
[dtor@mail.ru: Implement Henrik's suggestion and drop old events in
case of overflow.]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This commit adds the file Documentation/input/event-codes.txt.
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Many media center remotes have buttons intended for jumping straight to
one type of media browser or another -- commonly, images/photos/pictures,
audio/music, television, and movies. At present, remotes with an images
or photos or pictures button use any number of different keycodes which
sort of maybe fit. I've seen at least KEY_MEDIA, KEY_CAMERA,
KEY_GRAPHICSEDITOR and KEY_PRESENTATION. None of those seem quite right.
In my mind, KEY_MEDIA should be something more like a media center
application launcher (and I'd like to standardize on that for things
like the windows media center button on the mce remotes). KEY_CAMERA is
used in a lot of webcams, and typically means "take a picture now".
KEY_GRAPHICSEDITOR implies an editor, not a browser. KEY_PRESENTATION
might be the closest fit here, if you think "photo slide show", but it
may well be more intended for "run application in full-screen
presentation mode" or to launch something like magicpoint, I dunno.
And thus, I'd like to have a KEY_IMAGES, which matches the HID Usage AL
Image Browser, the meaning of which I think is crystal-clear. I believe
AL Audio Browser is already covered by KEY_AUDIO, and AL Movie Browser
by KEY_VIDEO, so I'm also adding appropriate comments next to those
keys.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Call posix_acl_valid() to check if an acl is valid or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Link count of the inode is not decreased if btrfs_set_inode_index()
fails.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Singed-off-by: Li Zefan <lizf@cn.fujitsu.com>
btrfs_next_leaf() can return -errno, and we should propagate
it to userspace.
This also simplifies how we walk the btree path.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
btrfs_next_leaf() can return -errno, and we should propagate
it to userspace.
This also simplifies how we walk the btree path.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Reported-by: Nick Bane <nickbane1@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The extent_io code can take cached pointers into the extent state trees,
and these can make lookups much faster in common operations. The
caching only happens when specific bits are set that prevent merging
and splitting of the extent state.
A help function was added to uncache the state, and it was testing
the same set of conditionals. This can leak in very strange corner
cases where the lock bit goes away unexpectedly.
The uncaching should be unconditional. Once we have a ref on the
extent we should always give it up.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This reverts commit 0a0883c843.
this was in my tree by accident, I meant to rebase it out and
didn't realise in time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 69a07f0b11.
We've tracked a number of problems back to this, and Thomas
thinks we should redesign this for .40/41 anyways so I'm
happy to revert it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
fix Kconfig warning:
(DRM_I915 && STUB_POULSBO) selects ACPI_VIDEO which has unmet direct dependencies
(ACPI && X86 && BACKLIGHT_CLASS_DEVICE && VIDEO_OUTPUT_CONTROL && INPUT)
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
