dwmmc driver deprecated num-slots and plan to get rid
of it finally. Just move a step to cleanup it from DT.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
During my research I found that some of the requirements for the memory
buffers for MFC v6+ devices were blindly copied from the previous (v5)
version and simply turned out to be excessive. The relaxed requirements
are applied by the recent patches to the MFC driver and the driver is
now fully functional even without the reserved memory blocks for all
v6+ variants. This patch removes those reserved memory nodes from all
boards having MFC v6+ hardware block.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Smitha T Murthy <smitha.t@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There's a cognitive load to figure out which mmc device node corresponds
to the eMMC flash, uSD card and WiFI SDIO module on the Snow, Peach Pi
and Pit boards.
So it's better to have comments in the DTS to make this more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
[krzk: Squashed three patches into one]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NN8A
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Pull "Topic branch for Samsung DeviceTree cleanup for 4.9" from Krzysztof Kozłowski:
Replace in DT sources hard-coded values for pinctrl configuration like pull
up/down, drive strength and function. This makes the DTS easier to read,
especially that some drive strengths values are quite non-obvious.
* tag 'samsung-dt-pinctrl-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
ARM: dts: exynos: Fix mismatched values of SD drive strengh configuration on exynos4415
ARM: dts: exynos: Fix mismatched value for SD4 pull up/down configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos542x/exynos5800
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5410
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5260
ARM: dts: exynos: Use macros for pinctrl configuration on exynos5250
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4415
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4x12
ARM: dts: exynos: Use macros for pinctrl configuration on exynos4210
ARM: dts: exynos: Use macros for pinctrl configuration on exynos3250
ARM: dts: exynos: Use common macros for pinctrl configuration
pinctrl: dt-bindings: samsung: Update documentation with new macros
pinctrl: dt-bindings: samsung: Add header with values used for configuration
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sS8p
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves assigning reserved memory regions from each board dts
to common exynos-mfc-reserved-memory.dtsi file, where those regions are
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch replaces custom properties for defining reserved memory
regions with generic reserved memory bindings for MFC video codec
device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
[k.kozlowski: Add Samsung copyrights]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The Exynos5800 Peach Pi and Exynos5420 Peach Pit Chromebooks have the
LDO10 1.8V output connected to the VDD18_TS{01,23,4} Exynos SoC pins.
Add this regulator as the input supply of the Thermal Management Unit
channels and also remove the always-on property since all the devices
using LDO10 as input supply are now defined.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The regulator always-on property should only be used for regulators
that either can't be disabled or the drivers for the client devices
are not enabling the regulator and so being disabled due to unused.
There are some max77802 regulators in the Peach Pit and Pi boards
that are always-on but shouldn't since they are enabled by drivers:
BUCK5 is max77802 inl1 supply
BUCK7 is max77802 inl{2,10} supply
BUCK9 is max77802 inl{3,4,5,7} supply
BUCK10 is mmc1 vqmmc supply
LDO9 is adc vdd supply
This patch removes the always-on property for these regulators.
Some regulators should remain always-on even when they are used as
input supplies, because these regulators are also used by other
components that are not described in the DT, for example:
LDO10 is hdmi vdd_osc supply but it's also used as input supply for
the Exynos5420 temperature sensor.
LDO8 is hdmi vdd and vdd_pll supply but it's also used as supply for
the Exynos5420 Display port.
BUCK2 and BUCK6 are the vdd supplies for the EAGLE and KFC clusters.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
The MFC nodes with the memory regions reserved for memory allocations
are missing in the Exynos5420 Peach Pit and Exynos5800 Peach Pi DTS.
This causes the s5p-mfc driver probe to fail with the following error:
[ 4.140647] s5p_mfc_alloc_memdevs:1072: Failed to declare coherent memory for MFC device
[ 4.216163] s5p-mfc: probe of 11000000.codec failed with error -12
Add the missing nodes so the driver probes and the {en,de}coder video
nodes are registered correctly:
[ 4.096277] s5p-mfc 11000000.codec: decoder registered as /dev/video4
[ 4.102282] s5p-mfc 11000000.codec: encoder registered as /dev/video5
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This pull request want to land the analogix_dp driver into drm/bridge directory,
which reused the Exynos DP code, and add Rockchip DP support. And those
patches have been:
* 'drm-next-analogix-dp-v2' of github.com:yakir-Yang/linux:
drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable time
drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time
drm: bridge: analogix/dp: add edid modes parse in get_modes method
drm: bridge: analogix/dp: move hpd detect to connector detect function
drm: bridge: analogix/dp: try force hpd after plug in lookup failed
drm: bridge: analogix/dp: add max link rate and lane count limit for RK3288
drm: bridge: analogix/dp: add some rk3288 special registers setting
dt-bindings: add document for rockchip variant of analogix_dp
drm: rockchip: dp: add rockchip platform dp driver
ARM: dts: exynos/dp: remove some properties that deprecated by analogix_dp driver
dt-bindings: add document for analogix display port driver
drm: bridge: analogix/dp: dynamic parse sync_pol & interlace & dynamic_range
drm: bridge: analogix/dp: remove duplicate configuration of link rate and link count
drm: bridge: analogix/dp: fix some obvious code style
drm: bridge: analogix/dp: rename register constants
drm/exynos: dp: rename implementation specific driver part
drm: bridge: analogix/dp: split exynos dp driver to bridge directory
After exynos_dp have been split the common IP code into analogix_dp driver,
the analogix_dp driver have deprecated some Samsung platform properties which
could be dynamically parsed from EDID/MODE/DPCD message, so this is an update
for Exynos DTS file for dp-controller.
Beside the backward compatibility is fully preserved, so there are no
bisectability break that make this change in a separate patch.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add cluster regulator supply properties as a preparation to
adding generic cpufreq-dt driver support for Exynos542x and
Exynos5800 based boards.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Exynos5420 and Exynos5800 boards boot from big core (A15) but
Exynos5422 boards choose otherwise: LITTLE core (A7) (on Exynos5422 this
is property of the board - configurable by pulling up/down gpg2-1).
To make user-visible CPU ordering more consistent the 'cpus' node was
overridden by exynos5422-cpus.dtsi.
However this is a little bit ugly and error-prone. Overriding the CPU
child nodes requires to basically reverse what was done initially in
exynos5420.dtsi.
Instead, split CPU configuration entirely to separate files which should
be included by board DTS.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanho Park <parkch98@gmail.com>
As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a crisp
overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XDLa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, the bulk of this release is again DT file contents.
There's a huge number of changes here, and it's challenging to give a
crisp overview of just what is in here. To start with:
New boards:
- TI-based DM3730 from LogicPD (Torpedo)
- Cosmic+ M4 (nommu) initial support (Freescale Vybrid)
- Raspberry Pi 2 DT files
- Watchdog on Meson8b
- Veyron-mickey (ASUS Chromebit) DTS
- Rockchip rk3228 SoC and eval board
- Sigma Designs Tango4
Improvements:
- Improved support for Qualcomm APQ8084, including Sony Xperia Z DT files
- Misc new devices for Rockchip rk3036 and rk3288
- Allwinner updates for misc SoCs and systems
... and a _large_ number of other changes across the field. Devices
added to SoC DTSI and board DTS files for a number of SoC vendors, new
product boards on already-supported SoCs, cleanups and refactorings of
existing DTS/DTSI files and a bunch of other changes"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (469 commits)
ARM: dts: compulab: add new board description
ARM: versatile: add the syscon LEDs to the DT
dts: vt8500: Fix errors in SDHC node for WM8505
ARM: dts: imx6q: clean up unused ipu2grp
ARM: dts: silk: Add compatible property to "partitions" node
ARM: dts: gose: Add compatible property to "partitions" node
ARM: dts: porter: Add compatible property to "partitions" node
ARM: dts: koelsch: Add compatible property to "partitions" node
ARM: dts: lager: Add compatible property to "partitions" node
ARM: dts: bockw: Add compatible property to "partitions" node
ARM: dts: meson8b: Add watchdog node
Documentation: watchdog: Add new bindings for meson8b
ARM: meson: Add status LED for Odroid-C1
ARM: dts: uniphier: fix a typo in comment block
ARM: bcm2835: Add the auxiliary clocks to the device tree.
ARM: bcm2835: Add devicetree for bcm2836 and Raspberry Pi 2 B
ARM: bcm2835: Move the CPU/peripheral include out of common RPi DT.
ARM: bcm2835: Split the DT for peripherals from the DT for the CPU
ARM: realview: set up cache correctly on the PB11MPCore
ARM: dts: Unify G2D device node with other devices on exynos4
...
The eMMC is non-removable so is marked with the non-removable DT
property to avoid having to redetect it after a suspend/resume.
But it also has the broken-cd property which is wrong since only
one of the DT properties for card detection should be used.
Also remove the card-detect-delay property that is not needed with
non-removable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The Exynos5800 Peach Pi Chromebook has a Marvell WiFi SDIO chip which
can't neither be removed nor be detected. But the node isn't marked
as non-removable and instead has the broken-cd DT property.
This causes the device to be removed when the system enters into a
suspend state and the following warnings is shown after a resume:
[ 181.944636] mmc2: error -2 during resume (card was removed?)
Also remove the card-detect-delay property that is not needed with
non-removable.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The DT binding for the Exynos DRM Display Port (DP) driver isn't consistent
since it uses a phandle to describe the connection between the DP port and
the display panel but uses the OF graph ports and endpoints to describe the
connection betwen the DP port, a bridge chip and the panel.
The Exynos DP driver and the DT binding have been changed to allow also to
describe the DP port to panel connection using ports / endpoints (OF graph)
so this patch changes the Exynos5800 Peach Pi DT to make it consistent with
the Exynos5420 Peach Pit that has a eDP to LVDS chip and uses OF graph too.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Peach boards use the EC to store the vboot context information,
so add the corresponding properties on the EC node to indicate so.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Emilio Lopez <emilio.lopez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Marvell mwifiex driver prevents the system to enter into a suspend
state if the card power is not preserved during a suspend/resume cycle.
So Suspend-to-RAM and Suspend-to-idle is failing on Exynos5800 Peach Pi
and Exynos5420 Peach Pit Chromebooks.
Add the keep-power-in-suspend Power Management property to the SDIO/MMC
node so the mwifiex suspend handler doesn't fail and the system is able
to enter into a suspend state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
HS400 timing values are added for SMDK5420, exynos5420-peach-pit
and exynos5800-peach-pi boards. This also adds RCLK GPIO line,
this gpio should be in pull-down state.
This also enables HS400 on peach-pi and this updates the clock
frequency to 800MHz to be set as input clock to controller.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
[alim.akhtar@samsung.com: addressed review comments]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The kernel can use as the default console a serial port if is defined
as stdout device in the Device Tree.
This allows a board to be booted without the need of having a console
parameter in the kernel command line.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
On Peach Pit and Pi boards, the Exynos SoC XCLKOUT pin provides
master clock (mclk) to the codec. So make it a clock consumer.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Peach Pit and Pi boards have a WiFi module that is always powered
but needs toggling an enable pin and ungating a 32kHz reference
clock as part of their power sequencing.
Add a dev node for the SDIO slot and a MMC power sequence provider.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The regulator core now has support to choose if a regulator
has to be enabled or disabled during system suspend and also
supports changing the regulator operating mode during runtime
and when the system enters into sleep mode.
To lower power during suspend, configure the regulators state
using the same configuration found in the ChromeOS 3.8 kernel
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam whose power supply is the tps65090 fet5
regulator. Since the camera uses the generic USB Video Class driver and
this does not grab a regulator, mark the regulator as always on so the
USB device is enumerated and usable.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have both
a power and lid GPIO keys but only the former was defined in the
DTS. Add DTS snippets for the lid GPIO key too. These were taken
from the downstream ChromeOS 3.8 kernel tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
MMC capability for HS200 is parsed in mmc/core/host.c as
dts string "mmc-hs200-1_8v".
This patch corrects the dts string for Exynos5420 based peach-pit
and Exynos5800 based peach-pi boards.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
commit 546b117fdf17 ("rtc: s3c: add support for RTC of Exynos3250 SoC")
added an "rtc_src" DT property for the Samsung's S3C Real Time Clock
controller that specifies the 32.768 kHz clock that uses the RTC as
its source clock. In the case of the Peach Pit and Pi machines, the
Maxim 77802 32kHz AP clock is used as the source clock.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Arc+
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
In case the optional dr_mode property isn't set in the dwc3 nodes the
the controller will go into OTG mode if both USB host and USB gadget
functionality are enabled in the kernel configuration. Unfortunately
this results in USB not working on exynos5420-peach-pit and
exynos5800-peach-pi with such a kernel configuration unless manually
change the mode. To resolve that explicitly configure the dual role
mode as host.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT nodes for panel-simple "auo,b133htn01" panel.
Add backlight enable pin and backlight power supply for pwm-backlight.
Also, add panel phandle needed by dp to enable display on peach_pi.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Peach Pi board has an Atmel maXTouch trackpad device.
Add the needed Device Tree nodes to support it.
This Device Tree change is based on the Chrome OS 3.8 tree
but adapted to use the mainline Atmel maXTouch DT binding.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The downstream ChromeOS 3.8 kernel sets the clock frequency
for the I2C bus 7 at 400kHz. Do the same change in mainline.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Exynos5420 based Peach Pit and the Exynos5800 based Peach Pi
machines have an i2c ISL29018 light sensor. This patch adds the
device nodes needed to support this device.
These DTS snippets were taken from the downstream Chrome OS 3.8
kernel Device Tree for Peach Pit and Pi boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch creates a thermistor fragment carrying the NTC
Thermistor nodes as children of the IIO based ADC.
This fragment is included in exynos5420-peach-pit.dts and
exynos5800-peach-pi.dts.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding regulators for HDMI for Peach-pi board.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Exynos5420 based Peach Pit and Exynos5800 based Peach Pi boards
uses a Maxim 77802 power management IC to drive regulators and
its Real Time Clock. This patch adds support for this chip.
These are the device nodes and pinctrl configuration that
are present on the Peach pit DeviceTree source file in the
the Chrome OS kernel 3.8 tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
