nfc_hci_recv_frame can not be called with a NULL skb.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
shdlc reset may leave HCI in an inconsistent state by loosing parts of
HCI frames. Handle this case by reporting an unrecoverable error to HCI.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The questions asked in the comments have been answered and addressed.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Its safe to stop the BTCOEX timers 'period_timer' and
'no_stomp_timer' before disabling BTCOEX. These timers
can call ath9k_hw_btcoex_enable (or) change the BT
stomp type if they seem to be running after we had
called ath9k_hw_btcoex_disable, which is obviously
not correct.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are doing MCI cleanup eventhough BTCOEX is not enabled
via module parameter. This means we do ath_mci_cleanup
though we skipped calling ath_mci_setup. Yet it does not
causes any issues now as we free the DMA buffer allocated
only when it is allocated during ath_mci_setup.
Reviewed-by: Bala Shanmugam <bkamatch@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having bus number printed makes it much easier to anaylze logs on
systems with more buses. For example Netgear WNDR4500 has 3 AMBA buses
in total, which makes standard log really messy.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an OOPS in brcmsmac driver, which was introduced
by the 11ad patch 'cfg80211: add 802.11ad (60gHz band) support'.
The value IEEE80211_NUM_BANDS increased, which was used in the
brcms_c_regd_init() function.
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the list of commands CMD_802_11_EEPROM_ACCESS had been
defined twice, unnecessarily, luckily with same value.
Remove one occurence.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables user to set mode of Tx/Rx path using "iw set antenna"
command. For non MIMO chips, the command will be used for selecting
specific antenna or configuring antenna diversity mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On full reset, mci reset will put LNA update on 2G mode. And
Whenever 2g5g_switch is forced at the end of full reset, lna
update should not be skipped. Not doing so, is affecting WLAN
rx and causing beacon loss when BTCOEX is enabled on AR9462.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip is waken up for every 45ms in btcoex timer cycle to
for sharing the radio between BT and WLAN. Whenever the wlan
interface is in network sleep mode, do not schedule hw timers.
This could reduce power consumption on idle associated state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as the interface brought up, btcoex timer starts running
eventhough the interface is in idle state and WLAN chip is moved
to full sleep mode. There is no point in running btcoex timer when
the wlan interface is in sleep mode and also it might consumes
more power on WLAN idle unassociated state. So lets stop the
btcoex when wlan is idle state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noise floor calibration is performed on longcal interval and
the reading will be updated in history buffer. On rare occasions,
the previous noisefloor calibration might not be completed within
the period and trying to load nf reading will be failed. In such
situation, postpone the nf cabliration to next cycle to give
enough time to complete the calibration. This was already taken
care for ar9002 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
noisefloor calibration has to be loaded and started after
chip reset completion and restoring chainmask. Right now it is
being started before MCI reset completion on full reset. Fix that.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is needed by brcmsmac. This code is based on code from
the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The list of devices where nothing has to be done in
bcma_pmu_resources_init() and bcma_pmu_workarounds() is longer as all
the SoCs are missing there and some new devices will be added in some
time later. This patch changes the default case to just log on debug
level and also let the other devices which do not need any special
handling into the default case, instead of adding the missing 8 SoC
chip ids.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These functions are doing nothing in the current code.
I do not think we will need these function in the future as the
corresponding functions in the Broadcom SDK are just doing something
useful on chips supported by ssb or fullmac chips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is based on the Broadcom SDK and brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ID was found on the PCIe wireless card on the board of a Netgear
WNDR3400 using a bcm4716. The device with this ID is identified by b43
as "Broadcom 43224 WLAN".
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is not core id with 0x4329, but at the same place in the open
source part of the Broadcom SDK is a check for some device with the
chip id of 0x4329. The device with a chip id of 0x4329 is a full mac
device, so it will never be supported by bcma, this part is running in
the firmware of the device and not on the host CPU.
This code is wrong and will never be used, so just remove it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip IDs are used all over bcma and no constants where defined.
This patch adds the constants and makes bcma use them.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a recent version of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some register values of bit shifts are corrected in order to support the upcoming
transmission power control (tpc) for control packets as well.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BTCOEX flags are set/cleared by atomic operations.
We got to do the same in ath9k_btcoex_timer_resume,
while clearing those BTCOEX flags.
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parse WPS IEs from start_ap as well as change_beacon handlers
and set them to FW. Beacon IEs, Probe Response IEs and Assoc
Response IEs are parsed from beacon_data and set to FW with
related masks.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Being a fullmac driver, mwifiex takes care of populating
beacon, probe response, association response WPS IEs to firmware.
And firmware is responsible for constructing these frames.
Advertise this to cfg80211.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for change_beacon handler which is needed
for setting modified management IEs to driver and FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>