This adds WoL support on TI DP83867 for magic, magic secure, unicast and
broadcast.
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move DT parsing code to probe dp83867_probe() as it's one time operation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link detection timeouts can be observed (or link might not be detected
at all) when dp83867 PHY is configured in manual mode (speed/duplex).
CFG3[9] Robust Auto-MDIX option allows to significantly improve link detection
in case dp83867 is configured in manual mode and reduce link detection
time.
As per DM: "If link partners are configured to operational modes that are
not supported by normal Auto MDI/MDIX mode (like Auto-Neg versus Force
100Base-TX or Force 100Base-TX versus Force 100Base-TX), this Robust Auto
MDI/MDIX mode allows MDI/MDIX resolution and prevents deadlock."
Hence, enable this option by default as there are no known reasons
not to do so.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN8740, like the 8720, also requires a reset after enabling clock.
The datasheet [1] 3.8.5.1 says:
"During a Hardware reset, an external clock must be supplied
to the XTAL1/CLKIN signal."
I have observed this issue on a custom i.MX6 based board with
the LAN8740A.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/8740a.pdf
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly
because genphy functions are designed for copper links, and 1000Base-X
(clause 37) auto negotiation needs to be handled differently.
This patch enables 1000Base-X support for BCM54616S by customizing 3
driver callbacks, and it's verified to be working on Facebook CMM BMC
platform (RGMII->1000Base-KX):
- probe: probe callback detects PHY's operation mode based on
INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX
Control register.
- config_aneg: calls genphy_c37_config_aneg when the PHY is running in
1000Base-X mode; otherwise, genphy_config_aneg will be called.
- read_status: calls genphy_c37_read_status when the PHY is running in
1000Base-X mode; otherwise, genphy_read_status will be called.
Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and
100Base-FX support is not available as of now.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for clause 37 1000Base-X auto-negotiation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the assignment to OR when dealing with phydev->dev_flags in
phy_attach_direct function, and this is to make sure dev_flags set in
driver's probe callback won't be lost.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of superseded function marvell_set_downshift() we can use new
function m88e1111_set_downshift() in m88e1116r_config_init().
For this m88e1116r_config_init() has to be moved in the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far downshift is implemented for one small use case only and can't
be controlled from userspace. So let's implement this feature properly
as a PHY tunable so that it can be controlled via ethtool.
More Marvell PHY's may support downshift, but I restricted it for now
to the ones where I have the datasheet.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.
This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there's a bug in the module subsystem [0] preventing load of
the PHY driver module on certain systems (as one symptom).
This results in a NPE on such systems for the following reason:
Instead of the correct PHY driver the genphy driver is loaded that
doesn't implement the read_page/write_page callbacks. Every call to
phy_read_paged() et al will result in a NPE therefore.
In parallel to fixing the root cause we should make sure that this one
and maybe similar issues in other subsystems don't result in a NPE
in phylib. So let's check for the callbacks before using them and warn
once if they are not available.
[0] https://marc.info/?t=157072642100001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than parsing the sfp firmware node in phylink, parse it in the
sfp-bus code, so we can re-use this code for PHYs without having to
duplicate the parsing.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more linkmode_* helpers rather than open-coding the bitmap
operations.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 400Gbps speed, link modes of 50Gbps per lane
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warnings in phylink.c:
../drivers/net/phy/phylink.c:595: warning: Function parameter or member 'config' not described in 'phylink_create'
../drivers/net/phy/phylink.c:595: warning: Excess function parameter 'ndev' description in 'phylink_create'
Fixes: 8796c8923d ("phylink: add documentation for kernel APIs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Don't populate const arrays on the stack but instead make them
static. Makes the object code smaller by 1058 bytes.
Before:
text data bss dec hex filename
29879 6144 0 36023 8cb7 drivers/net/phy/mscc.o
After:
text data bss dec hex filename
28437 6528 0 34965 8895 drivers/net/phy/mscc.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Read the PHY-specific status register for the current operating mode
(speed and duplex) of the PHY. This register reflects the actual
mode that the PHY has resolved depending on either the advertisements
of autoneg is enabled, or the forced mode if autoneg is disabled.
This ensures that phylib's software state always tracks the hardware
state.
It seems both AR8033 (which uses the AR8031 ID) and AR8035 support
this status register. AR8030 is not known at the present time.
This patch depends on "net: phy: extract pause mode" and "net: phy:
extract link partner advertisement reading".
Reported-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: tinywrkb <tinywrkb@gmail.com>
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the update of phylib's software pause mode state from
genphy_read_status(), so that we can re-use this functionality with
PHYs that have alternative ways to read the negotiation results.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move reading the link partner advertisement out of genphy_read_status()
into its own separate function. This will allow re-use of this code by
PHY drivers that are able to read the resolved status from the PHY.
Tested-by: tinywrkb <tinywrkb@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When userspace writes to the MII_ADVERTISE register, we update phylib's
advertising mask and trigger a renegotiation. However, writing to the
MII_CTRL1000 register, which contains the gigabit advertisement, does
neither. This can lead to phylib's copy of the advertisement becoming
de-synced with the values in the PHY register set, which can result in
incorrect negotiation resolution.
Fixes: 5502b218e0 ("net: phy: use phy_resolve_aneg_linkmode in genphy_read_status")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_device_reset() makes use of the atomic-pretending API flavor for
handling the PHY reset GPIO line.
I found no hint that mdio_device_reset() is called from atomic context
and indeed it uses usleep_range() since long time, so I would assume that
it is OK to sleep there.
This patch switch to gpiod_set_value_cansleep() in mdio_device_reset().
This is relevant if e.g. the PHY reset line is tied to a I2C GPIO
controller.
This has been tested on a ZynqMP board running an upstream 4.19 kernel and
then hand-ported on current kernel tree.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm54612e_config_init() duplicates what bcm54xx_config_clock_delay()
does with respect to configuring RGMII TX/RX delays appropriately.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0fc9ae1076 ("net: phy: broadcom: add support for
BCM54210E") added support for BCM54210E but also unconditionally cleared
the RXC to RXD skew and the TXD to TXC skew, thus only making
PHY_INTERFACE_MODE_RGMII a possible configuration. Use
bcm54xx_config_clock_delay() which correctly sets the registers
depending on the 4 possible PHY interface values that exist for RGMII.
Fixes: 0fc9ae1076 ("net: phy: broadcom: add support for BCM54210E")
Reported-by: Manasa Mudireddy <manasa.mudireddy@broadcom.com>
Reported-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct at803x_priv is never used in this driver. So remove it
and the probe function allocating it.
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly this hardware can work with generic PHY driver, but this change
is needed to provided interrupt handling support.
Tested with dsa ar9331-switch driver.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability.
Micrel KSZ9021 has no errata, but has the same issue with Asymmetric Pause.
This patch apply the same workaround as the one for KSZ9031.
Fixes: 3aed3e2a14 ("net: phy: micrel: add Asym Pause workaround")
Signed-off-by: Hans Andersson <hans.andersson@cellavision.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf1298 ("phy: Add file missed in previous commit.")
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
This driver becomes the first user of the kernel's `ETHTOOL_PHY_EDPD`
phy-tunable feature.
EDPD is also enabled by default on PHY config_init, but can be disabled via
the phy-tunable control.
When enabling EDPD, it's also a good idea (for the ADIN PHYs) to enable TX
periodic pulses, so that in case the other PHY is also on EDPD mode, there
is no lock-up situation where both sides are waiting for the other to
transmit.
Via the phy-tunable control, TX pulses can be disabled if specifying 0
`tx-interval` via ethtool.
The ADIN PHY supports only fixed 1 second intervals; they cannot be
configured. That is why the acceptable values are 1,
ETHTOOL_PHY_EDPD_DFLT_TX_MSECS and ETHTOOL_PHY_EDPD_NO_TX (which disables
TX pulses).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO device reset line is optional and now that gpiod_get_optional()
returns proper value when GPIO support is compiled out, there is no
reason to use fwnode_get_named_gpiod() that I plan to hide away.
Let's switch to using more standard gpiod_get_optional() and
gpiod_set_consumer_name() to keep the nice "PHY reset" label.
Also there is no reason to only try to fetch the reset GPIO when we have
OF node, gpiolib can fetch GPIO data from firmwares as well.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Signed-off-by: Vitaly Gaiduk <vitaly.gaiduk@cloudbear.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reported-by: Shaul Ben-Mayor <shaulb@marvell.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running stmmac selftests I found that in my 1G setup some tests
were failling when running with PHY loopback enabled.
It looks like when loopback is enabled the PHY will report that Link is
down even though there is a valid connection.
As in loopback mode the data will not be sent anywhere we can bypass the
logic of checking if Link is valid thus saving unecessary reads.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use set/get drv data in phydev's mdio device instead. Phy device priv
field maybe used by the external phy driver and should not be
overwritten.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethernet drivers may call phy_start() and phy_stop() from
ndo_open() and ndo_close() respectively.
When network cable is unconnected, and operate like below:
step 1: ifconfig ethX up -> ndo_open -> phy_start ->start
autoneg, and phy is no link.
step 2: ifconfig ethX down -> ndo_close -> phy_stop -> just stop
phy state machine.
This patch forces phy suspend even phydev->link is off.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34786005ec ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e8270 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFPs can report two different power values, the transmit power and the
receive power. Add labels to make it clear which is which. Also add
labels to the other sensors, VCC power supply, bias and module
temperature.
sensors(1) now shows:
sff2-isa-0000
Adapter: ISA adapter
VCC: +3.23 V
temperature: +33.4 C
TX_power: 276.00 uW
RX_power: 20.00 uW
bias: +0.01 A
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emulate the 802.3bz MMD EEE registers for 2.5Gbps EEE on RTL8125.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all users have been removed we can remove genphy_config_init.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed. All that
genphy_config_init does is removing features that are set as
supported but can't be auto-detected. Basically it duplicates the
code in genphy_read_abilities. Therefore remove such calls from
all PHY drivers.
v2:
- remove call also from new adin PHY driver
v3:
- pass NULL as config_init function pointer for dp83848
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change implements retrieving all the error counters from the PHY.
The counters require that the RxErrCnt register (0x0014) be read first,
after which copies of the counters are latched into the registers. This
ensures that all registers read after RxErrCnt are synchronized at the
moment that they are read.
The counter values need to be accumulated by the driver, as each time that
RxErrCnt is read, the values that are latched are the ones that have
incremented from the last read.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Down-speed auto-negotiation may not always be enabled, in which case the
PHY won't down-shift to 100 or 10 during auto-negotiation.
This change enables downshift and configures the number of retries to
default 4 (which is also in the datasheet
The downshift control mechanism can also be controlled via the phy-tunable
interface (ETHTOOL_PHY_DOWNSHIFT control).
The change has been adapted from the Aquantia PHY driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs supports 4 types of reset:
1. The standard PHY reset via BMCR_RESET bit in MII_BMCR reg
2. Reset via GPIO
3. Reset via reg GeSftRst (0xff0c) & reload previous pin configs
4. Reset via reg GeSftRst (0xff0c) & request new pin configs
Resets 2, 3 & 4 are almost identical, with the exception that the crystal
oscillator is available during reset for 2.
This change implements subsystem software reset via the GeSftRst and
reloading the previous pin configuration (so reset number 3).
This will also reset the PHY core regs (similar to reset 1).
Since writing bit 1 to reg GeSftRst is self-clearing, the only thing that
can be done, is to write to that register, wait a specific amount of time
(10 milliseconds should be enough) and try to read back and check if there
are no errors on read. A busy-wait-read won't work well, and may sometimes
work or not work.
In case phylib is configured to also do a reset via GPIO, the ADIN PHY may
be reset twice when the PHY device registers, but that isn't a problem,
since it's being done on boot (or PHY device register).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1200 & ADIN1300 PHYs support EEE by using standard Clause 45 access
to access MMD registers for EEE.
The EEE register addresses (when using Clause 22) are available at
different addresses (than Clause 45), and since accessing these regs (via
Clause 22) needs a special mechanism, a translation table is required to
convert these addresses.
For Clause 45, this is not needed since the driver will likely never use
this access mode.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN PHYs support automatic MDI/MDIX negotiation. By default this is
disabled, so this is enabled at `config_init`.
This is controlled via the PHY Control 1 register.
The supported modes are:
1. Manual MDI
2. Manual MDIX
3. Auto MDIX - prefer MDIX
4. Auto MDIX - prefer MDI
The phydev mdix & mdix_ctrl fields include modes 3 & 4 into a single
auto-mode. So, the default mode this driver enables is 4 when Auto-MDI mode
is used.
When detecting MDI/MDIX mode, a combination of the PHY Control 1 register
and PHY Status 1 register is used to determine the correct MDI/MDIX mode.
If Auto-MDI mode is not set, then the manual MDI/MDIX mode is returned.
If Auto-MDI mode is set, then MDIX mode is returned differs from the
preferred MDI/MDIX mode.
This covers all cases where:
1. MDI preferred & Pair01Swapped == MDIX
2. MDIX preferred & Pair01Swapped == MDI
3. MDI preferred & ! Pair01Swapped == MDIX
4. MDIX preferred & ! Pair01Swapped == MDI
The preferred MDI/MDIX mode is not configured via SW, but can be configured
via HW pins. Note that the `Pair01Swapped` is the Green-Yellow physical
pairs.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIFO depth can be configured for the RMII mode. This change adds
support for doing this via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal delays for the RGMII are configurable for both RX & TX. This
change adds support for configuring them via device-tree (or ACPI).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
unconfigured) is RGMII.
This change adds support for configuring these modes via the device
registers.
For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
the default delay is 2 ns. This can be configurable and will be done in
a subsequent change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ADIN1200 & ADIN1300 support Clause 45 access for some registers.
The Extended Management Interface (EMI) registers are accessible via both
Clause 45 (at register MDIO_MMD_VEND1) and using Clause 22.
The Clause 22 access for MMD regs differs from the standard one defined by
802.3. The ADIN PHYs use registers ExtRegPtr (0x0010) and ExtRegData
(0x0011) to access Clause 45 & EMI registers.
The indirect access is done via the following mechanism (for both R/W):
1. Write the address of the register in the ExtRegPtr
2. Read/write the value of the register via reg ExtRegData
This mechanism is needed to manage configuration of chip settings and to
access EEE registers via Clause 22.
Since Clause 45 access will likely never be used, it is not implemented via
this hook.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change hooks link-status-change interrupts to phylib.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports standard suspend/resume via BMCR reg.
Hook these functions into the `adin` driver.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for Analog Devices Industrial Ethernet PHYs.
Particularly the PHYs this driver adds support for:
* ADIN1200 - Robust, Industrial, Low Power 10/100 Ethernet PHY
* ADIN1300 - Robust, Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
The 2 chips are register compatible with one another. The main difference
being that ADIN1200 doesn't operate in gigabit mode.
The chips can be operated by the Generic PHY driver as well via the
standard IEEE PHY registers (0x0000 - 0x000F) which are supported by the
kernel as well. This assumes that configuration of the PHY has been done
completely in HW, according to spec.
Configuration can also be done via registers, which will be supported by
this driver.
Datasheets:
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1300.pdfhttps://www.analog.com/media/en/technical-documentation/data-sheets/ADIN1200.pdf
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE-related registers on newer integrated PHY's have the standard
layout, but are accessible not via MMD but via vendor-specific
registers. Emulating the standard MMD registers allows to use the
generic functions for EEE control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the genphy driver binds to a swphy it will call
genphy_read_abilites that will try to read MII_ESTATUS if BMSR_ESTATEN
is set in MII_BMSR. So far this would read the default value 0xffff
and 1000FD and 1000HD are reported as supported just by chance.
Better add explicit support for emulating MII_ESTATUS.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of MII_CTRL1000 is needed only if LPA_1000MSFAIL is set.
Therefore move reading this register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek provided information on how the new NIC-integrated PHY's
expose whether they support 2.5G/5G/10G. This allows to automatically
differentiate 1Gbps and 2.5Gbps PHY's, and therefore allows to
remove the fake PHY ID mechanism for RTL8125.
So far RTL8125 supports 2.5Gbps only, but register layout for faster
modes has been defined already, so let's use this information to be
future-proof.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
So far phy_speed_down/up can be used up to 1Gbps only. Remove this
restriction by using new helper __phy_speed_down. New member adv_old
in struct phy_device is used by phy_speed_up to restore the advertised
modes before calling phy_speed_down. Don't simply advertise what is
supported because a user may have intentionally removed modes from
advertisement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
phy_speed_down_core provides most of the functionality for
phy_speed_down. It makes use of new helper phy_resolve_min_speed that is
based on the sorting of the settings[] array. In certain cases it may be
helpful to be able to exclude legacy half duplex modes, therefore
prepare phy_resolve_min_speed() for it.
v2:
- rename __phy_speed_down to phy_speed_down_core
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We will need the functionality of __set_linkmode_max_speed also for
linkmode bitmaps other than phydev->supported. Therefore split it.
v2:
- remove unused parameter from __set_linkmode_max_speed
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This driver does a funny dance disabling and re-enabling
RX and/or TX delays. In any of the RGMII-ID modes, it first
disables the delays, just to re-enable them again right
away. This looks like a needless exercise.
Just enable the respective delays when in any of the
relevant 'id' modes, and disable them otherwise.
Also, remove comments which don't add anything that can't be
seen by looking at the code.
Signed-off-by: André Draszik <git@andred.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the integrated 2.5Gbps PHY in Realtek RTL8125.
Advertisement of 2.5Gbps mode is done via a vendor-specific register.
Same applies to reading NBase-T link partner advertisement.
Unfortunately this 2.5Gbps PHY shares the PHY ID with the integrated
1Gbps PHY's in other Realtek network chips and so far no method is
known to differentiate them. As a workaround use a dedicated fake PHY ID
that is set by the network driver by intercepting the MDIO PHY ID read.
v2:
- Create dedicated PHY driver and use a fake PHY ID that is injected by
the network driver. Suggested by Andrew Lunn.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper function phy_modify_paged_changed, behavios is the same
as for phy_modify_changed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The integrated PHY in 2.5Gbps chip RTL8125 is the first (known to me)
PHY that uses standard Clause 22 for all modes up to 1Gbps and adds
2.5Gbps control using vendor-specific registers. To use phylib for
the standard part little extensions are needed:
- Move most of genphy_config_aneg to a new function
__genphy_config_aneg that takes a parameter whether restarting
auto-negotiation is needed (depending on whether content of
vendor-specific advertisement register changed).
- Don't clear phydev->lp_advertising in genphy_read_status so that
we can set non-C22 mode flags before.
Basically both changes mimic the behavior of the equivalent Clause 45
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using linkmode_adv_to_mii_adv_t and linkmode_adv_to_mii_ctrl1000_t
allows to simplify the code. In addition avoiding the conversion to
the legacy u32 advertisement format allows to remove the warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 171a9bae68 ("staging/octeon: Allow test build on
!MIPS"), the following combination of configs cause a few Kconfig
warnings and build errors (distilled from arm allyesconfig and Randy's
randconfig builds):
CONFIG_NETDEVICES=y
CONFIG_STAGING=y
CONFIG_COMPILE_TEST=y
and CONFIG_OCTEON_ETHERNET as either a module or built-in.
WARNING: unmet direct dependencies detected for MDIO_OCTEON
Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y]
&& 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n]
Selected by [y]:
- OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC ||
COMPILE_TEST [=y]) && NETDEVICES [=y]
In file included from ../drivers/net/phy/mdio-octeon.c:14:
../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of
function ‘writeq’; did you mean ‘writel’?
[-Werror=implicit-function-declaration]
111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr)
| ^~~~~~
CONFIG_64BIT is not strictly necessary if the proper readq/writeq
definitions are included from io-64-nonatomic-lo-hi.h.
CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because
of commit f9dc9ac516 ("of/mdio: Add dummy functions in of_mdio.h.").
Fixes: 171a9bae68 ("staging/octeon: Allow test build on !MIPS")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_start_aneg() autoneg is started, and immediately after that
link and autoneg status are read. As reported in [0] it can happen that
at time of this read the PHY has reset the "aneg complete" bit but not
yet the "link up" bit, what can result in a false link-up detection.
To fix this don't report link as up if we're in aneg mode and PHY
doesn't signal "aneg complete".
[0] https://marc.info/?t=156413509900003&r=1&w=2
Fixes: 4950c2ba49 ("net: phy: fix autoneg mismatch case in genphy_read_status")
Reported-by: liuyonglong <liuyonglong@huawei.com>
Tested-by: liuyonglong <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.
The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_led_trigger_change_speed(), there is an if statement on line 48
to check whether phy->last_triggered is NULL:
if (!phy->last_triggered)
When phy->last_triggered is NULL, it is used on line 52:
led_trigger_event(&phy->last_triggered->trigger, LED_OFF);
Thus, a possible null-pointer dereference may occur.
To fix this bug, led_trigger_event(&phy->last_triggered->trigger,
LED_OFF) is called when phy->last_triggered is not NULL.
This bug is found by a static analysis tool STCheck written by
the OSLAB group in Tsinghua University.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly ok to not have an gpio attached to the fixed-link node. So
the driver should not throw an error message when the gpio is missing.
Fixes: 5468e82f70 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.
By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.
Results with this patch.
Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
validate().
- flow = results reported my link is Up line.
+-----+------------+-------+
| DT | validate() | flow |
+-----+------------+-------+
| Yes | Yes | rx/tx |
| No | Yes | off |
| Yes | No | off |
+-----+------------+-------+
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocated for the stats array may contain arbitrary data.
Fixes: e4f9ba642f ("net: phy: mscc: add support for VSC8514 PHY.")
Fixes: 00d70d8e0e ("net: phy: mscc: add support for VSC8574 PHY")
Fixes: a5afc16780 ("net: phy: mscc: add support for VSC8584 PHY")
Fixes: f76178dc52 ("net: phy: mscc: add ethtool statistics counters")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFP modules connected using the SGMII interface have their own PHYs which
are handled by the struct phylink's phydev field. On the other hand, for
the modules connected using 1000Base-X interface that field is not set.
Since commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network
devices and sfp cages") phylink_start() ends up setting the phydev field
using the sfp-bus infrastructure, which eventually calls phy_start() on it,
and then calling phy_start() again on the same phydev from phylink_start()
itself. Similar call sequence holds for phylink_stop(), only in the reverse
order. This results in WARNs during network interface bringup and shutdown
when a copper SFP module is connected, as phy_start() and phy_stop() are
called twice in a row for the same phy_device:
% ip link set up dev eth0
------------[ cut here ]------------
called from state UP
WARNING: CPU: 1 PID: 155 at drivers/net/phy/phy.c:895 phy_start+0x74/0xc0
Modules linked in:
CPU: 1 PID: 155 Comm: backend Not tainted 5.2.0+ #1
NIP: c0227bf0 LR: c0227bf0 CTR: c004d224
REGS: df547720 TRAP: 0700 Not tainted (5.2.0+)
MSR: 00029000 <CE,EE,ME> CR: 24002822 XER: 00000000
GPR00: c0227bf0 df5477d8 df5d7080 00000014 df9d2370 df9d5ac4 1f4eb000 00000001
GPR08: c061fe58 00000000 00000000 df5477d8 0000003c 100c8768 00000000 00000000
GPR16: df486a00 c046f1c8 c046eea0 00000000 c046e904 c0239604 db68449c 00000000
GPR24: e9083204 00000000 00000001 db684460 e9083404 00000000 db6dce00 db6dcc00
NIP [c0227bf0] phy_start+0x74/0xc0
LR [c0227bf0] phy_start+0x74/0xc0
Call Trace:
[df5477d8] [c0227bf0] phy_start+0x74/0xc0 (unreliable)
[df5477e8] [c023cad0] startup_gfar+0x398/0x3f4
[df547828] [c023cf08] gfar_enet_open+0x364/0x374
[df547898] [c029d870] __dev_open+0xe4/0x140
[df5478c8] [c029db70] __dev_change_flags+0xf0/0x188
[df5478f8] [c029dc28] dev_change_flags+0x20/0x54
[df547918] [c02ae304] do_setlink+0x310/0x818
[df547a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df547c28] [c02b222c] rtnl_newlink+0x48/0x68
[df547c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df547c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df547cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df547d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df547d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df547d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df547e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df547ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df547f38] [c000d1d8] ret_from_syscall+0x0/0x38
--- interrupt: c01 at 0xfd4e030
LR = 0xfd4e010
Instruction dump:
813f0188 38800000 2b890005 419d0014 3d40c046 5529103a 394aa208 7c8a482e
3c60c046 3863a1b8 4cc63182 4be009a1 <0fe00000> 48000030 3c60c046 3863a1d0
---[ end trace d4c095aeaf6ea998 ]---
and
% ip link set down dev eth0
------------[ cut here ]------------
called from state HALTED
WARNING: CPU: 1 PID: 184 at drivers/net/phy/phy.c:858 phy_stop+0x3c/0x88
<...>
Call Trace:
[df581788] [c0228450] phy_stop+0x3c/0x88 (unreliable)
[df581798] [c022d548] sfp_sm_phy_detach+0x1c/0x44
[df5817a8] [c022e8cc] sfp_sm_event+0x4b0/0x87c
[df581848] [c022f04c] sfp_upstream_stop+0x34/0x44
[df581858] [c0225608] phylink_stop+0x7c/0xe4
[df581868] [c023c57c] stop_gfar+0x7c/0x94
[df581888] [c023c5b8] gfar_close+0x24/0x94
[df5818a8] [c0298688] __dev_close_many+0xdc/0xf8
[df5818c8] [c029db58] __dev_change_flags+0xd8/0x188
[df5818f8] [c029dc28] dev_change_flags+0x20/0x54
[df581918] [c02ae304] do_setlink+0x310/0x818
[df581a08] [c02b1eb8] __rtnl_newlink+0x384/0x6b0
[df581c28] [c02b222c] rtnl_newlink+0x48/0x68
[df581c48] [c02ad7c8] rtnetlink_rcv_msg+0x240/0x27c
[df581c98] [c02cc068] netlink_rcv_skb+0x8c/0xf0
[df581cd8] [c02cba3c] netlink_unicast+0x114/0x19c
[df581d08] [c02cbd74] netlink_sendmsg+0x2b0/0x2c0
[df581d58] [c027b668] sock_sendmsg_nosec+0x20/0x40
[df581d68] [c027d080] ___sys_sendmsg+0x17c/0x1dc
[df581e98] [c027df7c] __sys_sendmsg+0x68/0x84
[df581ef8] [c027e430] sys_socketcall+0x1a0/0x204
[df581f38] [c000d1d8] ret_from_syscall+0x0/0x38
<...>
---[ end trace d4c095aeaf6ea999 ]---
SFP modules with the 1000Base-X interface are not affected.
Place explicit calls to phy_start() and phy_stop() before enabling or after
disabling an attached SFP module, where phydev is not yet set (or is
already unset), so they will be made only from the inside of sfp-bus, if
needed.
Fixes: 2179626156 ("net: phy: warn if phy_start is called from invalid state")
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX power read from the SFP uses units of 0.1uW. This must be
scaled to units of uW for HWMON. This requires a divide by 10, not the
current 100.
With this change in place, sensors(1) and ethtool -m agree:
sff2-isa-0000
Adapter: ISA adapter
in0: +3.23 V
temp1: +33.1 C
power1: 270.00 uW
power2: 200.00 uW
curr1: +0.01 A
Laser output power : 0.2743 mW / -5.62 dBm
Receiver signal average optical power : 0.2014 mW / -6.96 dBm
Reported-by: chris.healy@zii.aero
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 1323061a01 ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables phy_basic_ports_array, phy_fibre_port_array and
phy_all_ports_features_array are declared static and marked
EXPORT_SYMBOL_GPL(), which is at best an odd combination.
Because the variables were decided to be a part of API, this commit
removes the static attributes and adds the declarations to the header.
Fixes: 3c1bcc8614 ("net: ethernet: Convert phydev advertize and supported from u32 to link mode")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linkmode_mod_bit is introduced as a helper function to set/clear
bits in a linkmode.
Replace the if else code structure with a call to the helper
linkmode_mod_bit.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ef7bfa8472.
Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The acpi_node_get_property_reference() doesn't return ACPI error codes,
it just returns regular negative kernel error codes. This patch doesn't
affect run time, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ruslan Babayev <ruslan@babayev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This puts the quad PHY ports in power-down mode when the PHY transitions
to the PHY_HALTED state. It is likely that all the other PHYs support
the BMCR_PDOWN bit, but I only have the BCM5464R to test.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
