Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when the board does not support GPIOs for these
signals.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM. It seems rather common that GPON modules
mis-report.
Let's fix these modules by adding some quirks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for applying module quirks to the list of supported
ethtool link modes.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the call to phy_interface_is_rgmii returns zero
the variable ret is left uninitialized and this is returned at
the end of the function dp83869_configure_rgmii. Fix this by
returning 0 instead of the uninitialized value in ret.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 01db923e83 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently match clause 45 PHYs using any ID read from a MMD marked
as present in the "Devices in package" registers 5 and 6. However,
this is incorrect. 45.2 says:
"The definition of the term package is vendor specific and could be
a chip, module, or other similar entity."
so a package could be more or less than the whole PHY - a PHY could be
made up of several modules instantiated onto a single chip such as the
Marvell 88x3310, or some of the MMDs could be disabled according to
chip configuration, such as the Broadcom 84881.
In the case of Broadcom 84881, the "Devices in package" registers
contain 0xc000009b, meaning that there is a PHYXS present in the
package, but all registers in MMD 4 return 0xffff. This leads to our
matching code incorrectly binding this PHY to one of our generic PHY
drivers.
This patch changes the way we determine whether to attempt to match a
MMD identifier, or use it to request a module - if the identifier is
all-ones, then we skip over it. When reading the identifiers, we
initialise phydev->c45_ids.device_ids to all-ones, only reading the
device ID if the "Devices in package" registers indicates we should.
This avoids the generic drivers incorrectly matching on a PHY ID of
0xffffffff.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP+ cages to the Marvell 10G PHY driver. This is
slightly complicated by the way phylib works in that we need to use
a multi-step process to attach the SFP bus, and we also need to track
the phylink state machine to know when the module's transmit disable
signal should change state.
With appropriate DT changes, this allows the SFP+ canges on the
Macchiatobin platform to be functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add core phylib help for supporting SFP sockets on PHYs. This provides
a mechanism to inform the SFP layer about PHY up/down events, and also
unregister the SFP bus when the PHY is going away.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use phy_support_asym_pause() rather than open-coding it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver enables rising edge or falling edge, but not both, and so
this patch validates that the request contains only one of the two
edges.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space may request time stamps on rising edges, falling edges, or
both. However, the particular mode may or may not be supported in the
hardware or in the driver. This patch adds a "strict" flag that tells
drivers to ensure that the requested mode will be honored.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the dp83640 PTP support to explicitly reject any future flags that
get added to the external timestamp request ioctl.
In order to maintain currently functioning code, this patch accepts all
three current flags. This is because the PTP_RISING_EDGE and
PTP_FALLING_EDGE flags have unclear semantics and each driver seems to
have interpreted them slightly differently.
For the record, the semantics of this driver are:
flags Meaning
---------------------------------------------------- --------------------------
PTP_ENABLE_FEATURE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE Time stamp rising edge
PTP_ENABLE_FEATURE|PTP_FALLING_EDGE Time stamp falling edge
PTP_ENABLE_FEATURE|PTP_RISING_EDGE|PTP_FALLING_EDGE Time stamp falling edge
Cc: Stefan Sørensen <stefan.sorensen@spectralink.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823eb2a3c4 ("PTP: add support for one-shot output") introduced
a new flag for the PTP periodic output request ioctl. This flag is not
currently supported by any driver.
Fix all drivers which implement the periodic output request ioctl to
explicitly reject any request with flags they do not understand. This
ensures that the driver does not accidentally misinterpret the
PTP_PEROUT_ONE_SHOT flag, or any new flag introduced in the future.
This is important for forward compatibility: if a new flag is
introduced, the driver should reject requests to enable the flag until
the driver has actually been modified to support the flag in question.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christopher Hall <christopher.s.hall@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83869 Gigabit ethernet phy
device.
The DP83869 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the following VSC PHYs
VSC8504, VSC8552, VSC8572
VSC8562, VSC8564, VSC8575, VSC8582
Updates for v2:
Checked for NULL on input to container_of
Changed a large if else series to a switch statement.
Added a WARN_ON to make sure lowest nibble of mask is 0
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
Fix this by using IS_ERR before PTR_ERR
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 71dd6c0dff ("net: phy: add support for reset-controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a module is inserted, we attempt to read read the ID from address
0x50. Once we are able to read the ID, we immediately attempt to
initialise the hwmon support by reading from address 0x51. If this
fails, then we fall into error state, and assume that the module is
not usable.
Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for
I2C address 0x50, which responds immediately. However, address 0x51
is an emulated, which only becomes available once the on-board firmware
has booted. This prompts us to fall into the error state.
Since the module may be usable without diagnostics, arrange for the
hwmon probe independent of the rest of the SFP itself, retrying every
5s for up to about 60s for the monitoring to become available, and
print an error message if it doesn't become available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some GPON modules (e.g. Huawei MA5671A) take a significant amount of
time to start responding on the I2C bus, contary to the SFF
specifications.
Work around this by implementing a two-level timeout strategy, where
we initially quickly retry for the module, and then use a slower retry
after we exceed a maximum number of quick attempts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the module insertion reporting out of the probe handling, but
after we have detected that the upstream has attached (since that is
whom we are reporting insertion to.)
Only report module removal if we had previously reported a module
insertion.
This gives cleaner semantics, and means we can probe the module before
we have an upstream attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the power mode switching from the probe, so that we don't
repeatedly re-probe the SFP device if there is a problem accessing
the registers at I2C address 0x51.
In splitting this out, we can also fix a bug where we leave the module
in high-power mode when the upstream device is detached but the module
is still inserted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the upstream's attachment state in the state machine rather than
maintaining a boolean, which ensures that we have a strict order of
ATTACH followed by an UP event - we can never believe that a newly
attached upstream will be anything but down.
Rearrange the order of state machines so we run the module state
machine after the upstream device's state machine, so the module state
machine can check the current state of the device and take action to
e.g. reset back to empty state when the upstream is detached.
This is to allow the module detection to run independently of the
network device becoming available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_FAULT should be deasserted to indicate that the module has completed
its initialisation. This may include the on-board PHY, so wait until
the module has deasserted TX_FAULT before probing the PHY.
This means that we need an extra state to handle a TX_FAULT that
remains set for longer than t_init, since using the existing handling
state would bypass the PHY probe.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the next state to sfp_sm_fault() so that it can branch to other
states. This will be necessary to improve the initialisation path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using mdelay() to wait before probing the PHY (which holds
several locks, including the rtnl lock), add an extra wait state to
the state machine to introduce the 50ms delay without holding any
locks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY probe into a separate function, splitting it from
sfp_sm_mod_init(). This will allow us to eliminate the 50ms mdelay()
inside the state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialise TX_DISABLE when the sfp cage is probed, and then
maintain its state in the main state machine. However, the module
state machine:
- negates it when detecting a newly inserted module when it's already
guaranteed to be negated.
- negates it when the module is removed, but the main state machine
will do this anyway.
Make TX_DISABLE entirely controlled by the main state machine.
The main state machine also probes the module for a PHY, and removes
the PHY when the the module is removed. Hence, removing the PHY in
sfp_sm_module_remove() is also redundant, and is a left-over from
when we tried to probe for the PHY from the module state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the module indicates that it requires an address change sequence to
switch between address 0x50 and 0x51, which we don't support, we can't
write to the register that controls the power mode to switch to high
power mode. Warn the user that the module may not be functional in
this case, and don't try to change the power mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse the SFP power requirement earlier, in preparation for moving the
power level setup code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFF-8472 rev 12.2 defines the time for the serial bus to become ready
using t_serial. Use this as our identifier for this timeout to make
it clear what we are referring to.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing a module resets the module state machine back to its initial
state. Rather than explicitly handling this in every state, handle it
early on outside of the state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfp_sm_ins_next() modifies the module state machine. Change it's name
to reflect this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the tx disable assertion on device down to the main state
machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the SFP sub-state machines out of the main state machine function,
in preparation for it doing a bit more with the device state. By doing
so, we ensure that our debug after the main state machine is always
printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild test robot found a problem with htmldocs with the recent
change to the SFP interfaces. Fix the kernel documentation for
sfp_bus_put() which was missing an '@' before the argument name
description.
Fixes: 727b3668b7 ("net: sfp: rework upstream interface")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstream interface is an all-or-nothing, which is
sub-optimal for future changes, as it doesn't allow the upstream driver
to prepare for the SFP module becoming available, as it is at boot.
Switch to a find-sfp-bus, add-upstream, del-upstream, put-sfp-bus
interface structure instead, which allows the upstream driver to
prepare for a module being available as soon as add-upstream is called.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compilation fails on PPC targets as CONFIG_REGULATOR is not set and
drivers/regulator/devres.c is not compiled in while functions exported
there are used by drivers/net/phy/at803x.c. Here's the error log:
LD .tmp_vmlinux1
drivers/net/phy/at803x.o: In function `at803x_rgmii_reg_set_voltage_sel':
drivers/net/phy/at803x.c:294: undefined reference to `.rdev_get_drvdata'
drivers/net/phy/at803x.o: In function `at803x_rgmii_reg_get_voltage_sel':
drivers/net/phy/at803x.c:306: undefined reference to `.rdev_get_drvdata'
drivers/net/phy/at803x.o: In function `at8031_register_regulators':
drivers/net/phy/at803x.c:359: undefined reference to `.devm_regulator_register'
drivers/net/phy/at803x.c:365: undefined reference to `.devm_regulator_register'
drivers/net/phy/at803x.o:(.data.rel+0x0): undefined reference to `regulator_list_voltage_table'
linux/Makefile:1074: recipe for target 'vmlinux' failed
make[1]: *** [vmlinux] Error 1
Fixes: 2f664823a4 ("net: phy: at803x: add device tree binding")
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to its datasheet, the internal PHY doesn't have debug
registers nor MMDs. Since config_init() only configures delays and
clocks and so on in these registers it won't be needed on this PHY.
Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix at least the displayed strings. The actual name of the chip is
AR803x.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AR8033 is the AR8031 without PTP support. All other registers are
the same. Unfortunately, they share the same PHY ID. Therefore, we
cannot distinguish between the one with PTP support and the one without.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name of the PHY is actually AR803x not AT803x. Additionally, add the
name of the vendor and mention the AR8031 support.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink_dbg() macro does not follow dynamic debug or defined(DEBUG)
and as a result, it spams the kernel log since a PR_DEBUG level is
currently used. Fix it to be defined appropriately whether
CONFIG_DYNAMIC_DEBUG or defined(DEBUG) are set.
Fixes: 17091180b1 ("net: phylink: Add phylink_{printk, err, warn, info, dbg} macros")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add downshift support for 88E1145, it uses the same downshift
configuration registers as 88E1111.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More PHY versions are compatible with the existing downshift
implementation, so let's add downshift support for them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds downshift support for M88E1111. This PHY version uses
another register for downshift configuration, reading downshift status
is possible via the same register as for other PHY versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got access to the M88E1111 datasheet, and this PHY version uses
another register for downshift configuration. Therefore change prefix
to m88e1011, aligned with constants like MII_M1011_PHY_SCR.
Fixes: a3bdfce7bf ("net: phy: marvell: support downshift as PHY tunable")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo and use PHY_SCR for PHY-specific Control Register.
Fixes: a3bdfce7bf ("net: phy: marvell: support downshift as PHY tunable")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
