[why]
At the time DIG FE is connected to its BE, the clocks in OTG are enabled and
PHY will also be set up. When DSC has to be used to fit the stream into the
available bandwidth, without DSC being set DIG could get exposed to the
higer bandwidth it (or link) could handle. This causes the HW to "reject"
video enable setup (the register shows that video enable was attempted, but
the status bit shows it as disabled).
[how]
- Separate DSC setup into DSC register config and DSC PPS SDP setup
- Move most of the DSC setup (register config) to before
dcn10_link_encoder_connect_dig_be_to_fe() is called
- Set up DSC PPS SDP after DIG FE is connected to its BE. This is because
setting DSC PPS SDP before that has no effect.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why] Minimum slice height is recommended by VESA DSC Spreadsheet user guide
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Support hlg OETF and EOTF based on BT.2100-2
Follow up is required.
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Previous "less risky" implemenation of 3 tiered fallback is no longer necessary since
DMLv2 has gone through proper validation. v2 can now be used as the default and 1
level of fallback can be removed
[how]
remove previous workaround implemenation
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot (building SW state inheriting BIOS-initialized timing) was
enabled on DCN2, including fixes
[How]
Includes fixes for MPC, DPPCLK, and DIG FE mapping/OTG source select/
Pixel clock.
This is part 2 of 2 for seamless boot NV10
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow seen on certain monitor setups caused by making dcnxx_init_hw
generic
[How]
by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr
init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr
memset in an else statement so both memsets don't get set
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For seamless boot the init_hw sequence must be split into
actual hardware vs pipes, in order to defer pipe initialization to set mode
and skip of pipe-destructive sequences
[How]
made dcn10_init_hw and dcn10_init_pipes generic for future dcns to inherit
deleted dcn20 specific versions. This is part 1 of a 2 partimplementation
of seamless boot
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When planes are enabled, they must be enabled using VSYNC update (not immediate).
However, before the VUPDATE occurs, DM may call with an "immediate" flip which is address
only. This operation would normally be okay, but if the locking for immediate flip happens
to occur before the VUPDATE associated with the initial plane enablement, it will cause HW
to hang.
[how]
HWSS should enforce plane enable in HW to be synchronous with the call that enables the plane.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
if dynamic allocation fails during gpio_open, it will cause crash due to
page fault.
[how]
handle allocation when gpio object gets created and prevent from calling
gpio_open if allocation failed
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Auto Overclock Memory fails for some systems that don't support
p-state.
[How] Implement the workaround, and it's corresponding enable flag.
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DC does not correct account for the fact that DPP DTO is double buffered while DPP ref is not.
This means that when DPP ref clock is lowered when it's "safe to lower", the DPP blocks that need
an increased divider will temporarily have actual DPP clock drop below minimum while DTO
double buffering takes effect. This results in temporary underflow.
[how]
To fix this, DPP clock cannot be programmed atomically, but rather be broken up into the DTO and the
ref. Each has a separate "safe to lower" logic. When doing "prepare" the ref and dividers may only increase.
When doing "optimize", both may decrease. It is guaranteed that we won't exceed max DPP clock because
we do not use dividers larger than 1.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We require a method to perform synchronous link training.
[HOW]
Sync LT is broken into 3 basic steps.
"Begin" starts the state machine, and resets "preferred" link settings.
"Attempt" will attempt to train the link with a given set of training
parameters.
"End" stops the state machine, and will optionally disable the link phy.
Between "Begin" and "End" DPCD:600h must not be set to "2"
(D3:Powered Down).
Between "Begin" and "End", there may be multiple "Attempts" with different
training parameters.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN20 common register list that contains registers shared
between DCN20 generations.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Support degamma ROM and RAM based on hardware capabilities.
Some refactoring into color module
Signed-off-by: Vitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: Gary Kattan <Gary.Kattan@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Vitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The math on deciding on how many
"frames to insert" sometimes sent us over the max refresh rate.
Also integer overflow can occur if we have high refresh rates.
[How]
Instead of clipping the frame duration such that it doesn’t go below the min,
just remove a frame from the number of frames to insert. +
Use unsigned long long for intermediate calculations to prevent
integer overflow.
Signed-off-by: Bayan Zabihiyan <bayan.zabihiyan@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hdmi data scramble and tmds rate is not reset during pipe reset.
[how]
reset hdmi tmds rate and data scramble on pipe reset
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
drr is still enabled after driver is unloaded causing black screen
[how]
disable drr during pipe reset.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add to clk_mgr_internal struct, for future use.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For use by future ASICs
Signed-off-by: Sung Lee <sung.lee@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The spsc_queue_peek function is accessing queue->head which belongs to
the consumer thread and shouldn't be accessed by the producer
This is fixing a rare race condition when destroying entities.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Monk.liu@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a pr_err error message. Fix it. Also
add a space after a comma to clean up a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
get mmhub ea ras error count by accessing EDC_CNT register
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
simplify driver code.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
fix typo error:
change function name from "amdgput_ctx_total_num_entities" to
"amdgpu_ctx_total_num_entities".
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
the direct send message to smc to set hard clokc will failed
when smc clock dpm feature is disabled.
so use function of smu_set_hard_freq_range to replace it.
the function will check feature enablement.
eg: when uclk (mclk) dpm feature is disabled on navi10
[ 300.675901] amdgpu: [powerplay] failed send message: SetHardMinByFreq(28)
param: 0x00020064 response 0xfffffffb
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add arcturus_is_dpm_running function
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
remove redundancy debug log about smu unsupported features
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu uses a need_dma32 flag to indicate to the drm core that some
allocations need to be done using GFP_DMA32, but it only checks the
device addressing capabilities to make that decision. Unfortunately
PCIe root ports that have limited addressing exist as well. Use the
dma_addressing_limited instead to also take those into account.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
radeon uses a need_dma32 flag to indicate to the drm core that some
allocations need to be done using GFP_DMA32, but it only checks the
device addressing capabilities to make that decision. Unfortunately
PCIe root ports that have limited addressing exist as well. Use the
dma_addressing_limited instead to also take those into account.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reported-by: Atish Patra <Atish.Patra@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code won't likely work on production hw when
it ships so leave it as experimental until it's ready.
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir need not load mec2 jump table with psp.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PSP has issue for renoir, that will cause VCN fw failed to be loaded. So use
direct loading for the moment till the issue is addressed.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By default, set amdgpu ucode type to AMDGPU_FW_LOAD_PSP.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Thus enable VCN2.0 for Renoir
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add VCN range aperture to NBIO 7.0
v2: rebase (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
By adding new Renoir VCN firmware
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds gfx golden settings for renoir real asic.
v2: update settings (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Add psp ip block
2. Use direct loading type by default and it can also config psp
loading type.
3. Bypass sos fw loading and xgmi&ras interface
v2: drop TA loading
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
