This PHY has internal delays enabled after reset. This clears the
internal delay enables unless the interface specifically requests them.
Signed-off-by: Xo Wang <xow@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AQR106 and AQR107 can use the existing driver.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create an option CONFIG_LED_TRIGGER_PHY (default n), which will create a
set of led triggers for each instantiated PHY device. There is one LED
trigger per link-speed, per-phy.
The triggers are registered during phy_attach and unregistered during
phy_detach.
This allows for a user to configure their system to allow a set of LEDs
not controlled by the phy to represent link state changes on the phy.
LEDS controlled by the phy are unaffected.
For example, we have a board where some of the leds in the
RJ45 socket are controlled by the phy, but others are not. Using the
triggers provided by this patch the leds not controlled by the phy can
be configured to show the current speed of the ethernet connection. The
leds controlled by the phy are unaffected.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_supported_speeds provides a means to get a list of all the speeds a
phy device currently supports.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During phy state machine state transitions some set of actions should
occur whenever the link state changes. These actions should be
encapsulated into a single function
This patch adds the phy_adjust_link function, which is called whenever
phydev->adjust_link would have been called before. Actions that should
occur whenever the phy link is adjusted can now be added to the
phy_adjust_link function.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for programmable MAC impedance configuration
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the fixed name "phy_interrupt" is not very informative in
/proc/interrupts when there are a lot of phys, e.g. a device with an
Ethernet switch. So when requesting the interrupt, use the name of the
phy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY interrupts are now handled in a threaded interrupt handler,
which can sleep. The work queue is no longer needed, phy_change() can
be called directly. phy_mac_interrupt() still needs to be safe to call
in interrupt context, so keep the work queue, and use a helper to call
phy_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt lines from PHYs maybe connected to I2C bus expanders, or
from switches on MDIO busses. Such interrupts are sourced from devices
which sleep, so use threaded interrupts. Threaded interrupts require
that the interrupt requester also uses the threaded API. Change the
phylib to use the threaded API, which is backwards compatible with
none-threaded IRQs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-Rate cleanup include the following:
- Updated device tree bindings documentation for edge-rate
- The edge-rate is now specified as a "slowdown", meaning that it is now
being specified as positive values instead of negative (both
documentation and implementation wise).
- Only explicitly documented values for "vsc8531,vddmac" and
"vsc8531,edge-slowdown" are accepted by the device driver.
- Deleted include/dt-bindings/net/mscc-phy-vsc8531.h as it was not needed.
- Read/validate devicetree settings in probe instead of init
Signed-off-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: Raju Lakkaraju <raju.lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Kyle Roeschley <kyle.roeschley@ni.com>
Tested-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An extra entry for MDIO_XGENE got added during merging.
Delete it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wake-on-LAN (WoL) is an Ethernet networking standard that allows
a computer/device to be turned on or awakened by a network message.
VSC8531 PHY can support this feature configure by driver set function.
WoL status get by driver get function.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set bit 0 in register 1C.23 to enable the EDPD feature of the
KSZ9031 PHY. This reduces power consumption when the link is
down.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Edge-rate:
As system and networking speeds increase, a signal's output transition,
also know as the edge rate or slew rate (V/ns), takes on greater importance
because high-speed signals come with a price. That price is an assortment of
interference problems like ringing on the line, signal overshoot and
undershoot, extended signal settling times, crosstalk noise, transmission
line reflections, false signal detection by the receiving device and
electromagnetic interference (EMI) -- all of which can negate the potential
gains designers are seeking when they try to increase system speeds through
the use of higher performance logic devices. The fact is, faster signaling
edge rates can cause a higher level of electrical noise or other type of
interference that can actually lead to slower line speeds and lower maximum
system frequencies. This parameter allow the board designers to change the
driving strange, and thereby change the EMI behavioral.
Edge-rate parameters (vddmac, edge-slowdown) get from Device Tree.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the review comments updated and resending for review.
This is MAC interface feature.
Microsemi PHY can support RGMII, RMII or GMII/MII interface between MAC and PHY.
MAC-IF function program the right value based on Device tree configuration.
Tested on Beaglebone Black with VSC 8531 PHY.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get 1 warning when building kernel with W=1:
drivers/net/phy/microchip.c:58:5: warning: no previous prototype for 'lan88xx_suspend' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'IS_ERR(pdata->clk)' is true, then 'clk_disable_unprepare(pdata->clk)'
will do nothing.
It is likely that 'if (!IS_ERR(pdata->clk))' was expected here.
In fact, the test can even be removed because 'clk_disable_unprepare'
already handles such cases.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-xgene driver is only useful on X-Gene SoC.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Iyappan Subramanian <isubramanian@apm.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing VSC85xx PHY driver did not follow the coding style and caused "checkpatch" to complain. This commit fixes this.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
commit 33c133cc75 ("phy: IRQ cannot be shared")
On hardware with multiple PHY devices hooked up to the same IRQ line, allow
them to share it.
Sergei Shtylyov says:
"I'm not sure now what was the reason I concluded that the IRQ sharing
was impossible... most probably I thought that the kernel IRQ handling
code exited the loop over the IRQ actions once IRQ_HANDLED was returned
-- which is obviously not so in reality..."
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/phy/xilinx_gmii2rgmii.c:61:5: warning:
symbol 'xgmiitorgmii_probe' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the ksz8081, the ksz9031 has the behavior where it will clear the
interrupt enable bits when leaving power down. This takes advantage of the
solution provided by f5aba91.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This node pointer is returned by of_parse_phandle() with
refcount incremented in this function. of_node_put() on it
before exitting this function.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the redundant "Support for" and "Drivers for" from the Kconfig
short description. This makes the manufacture much more prominent in
the list and makes the shortcut keys useful.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sort the files to reduce merge conflicts and to make it easier to find
drivers by name. Also separate the MDIO bus drivers from the PHY
drivers, again to help find what you need.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implementing this driver most of the inputs is
provided by Andrew Lunn.
Updating the driver with Andrew Copy right.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function of_parse_phandle() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where phydev->interrupts is not PHY_INTERRUPT_ENABLED
function vsc85xx_ack_interrupt is returning an uninitialized
garbage value. Fix this by initializing rc to zero.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for gmiitorgmii converter.
The GMII to RGMII IP core provides the Reduced Gigabit Media
Independent Interface (RGMII) between Ethernet physical media
Devices and the Gigabit Ethernet controller. This core can
Switch dynamically between the three different speed modes of
Operation by configuring the converter register through mdio write.
MDIO interface is used to set operating speed of Ethernet MAC.
This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable all interrupts when suspend, they will be enabled
when resume. Otherwise, the suspend/resume process will be
blocked occasionally.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them
as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021
ignore the last two bits when matching PHY_ID
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-By: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, SGMII based 1G rely on the hardware registers for link state
and sometimes it's not reliable. To get most accurate link state, this
interface has to use the MDIO bus to poll the PHY.
In X-Gene SoC, MDIO bus is shared across RGMII and SGMII based 1G
interfaces, so adding this driver to manage MDIO bus. This driver
registers the mdio bus and registers the PHYs connected to it.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions used standards registers in a different page
for both interfaces: copper and fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be correctly initilized, the fiber interface needs
to be configured via autonegociation registers which use
some customs options or registers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the fiber receiver error counter in the
statistics. Rename the current counter which is for copper errors to
phy_receive_errors_copper, so it is easy to distinguish copper from
fiber.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
For concerned phy, the fiber link is checked before the copper link.
According to datasheet, the link which is up is enabled.
If both links are down, copper link would be used.
To detect fiber link status, we used the real time status
because of troubles with the copper method.
Tested with Marvell 88E1512.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Charles-Antoine Couret <charles-antoine.couret@nexvision.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a separate driver for the MDIO interface of the
Hisilicon Fast Ethernet MAC.
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Reviewed-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't detect the FXEN (fiber mode) bootstrap pin, so configure
it via a boolean device tree property "micrel,fiber-mode".
If it is enabled, auto-negotiation is not supported.
The only available modes are 100base-fx (full duplex and half duplex).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the PHY control register, the FIFO depth bits are
written without reading the previous register value, i.e. all other
bits are overwritten with zero. This disables automatic MDI-X
configuration, which is enabled by default. Fix initialization by doing
a read/modify/write operation.
Signed-off-by: Stefan Hauser <stefan@shauser.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 88E1111 currently uses the generic marvell config ANEG function.
This function has a sequence accessing Page 5 and Register 31,
both of which are not defined or reserved for this PHY.
Hence this patch adds a new config ANEG function for Marvell 88E1111
without these erroneous accesses.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a system which uses fixed PHY devices and calls
fixed_phy_register() then fixed_phy_unregister() we can exhaust the
number of fixed PHYs available after a while, since we keep incrementing
the variable phy_fixed_addr, but we never decrement it.
This patch fixes that by converting the fixed PHY allocation to using
IDA, which takes care of the allocation/dealloaction of the PHY
addresses for us.
Fixes: a759512174 ("net: phy: extend fixed driver with fixed_phy_register()")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
