Our VDSO code makes use of macros from linux/irqchip/mips-gic.h to
provide offsets to register values, but these are trivial offsets to the
two 32 bit halves of a 64 bit value. Replace use of the macros with zero
(ie. omit adding an offset) and the size of the low 32 bit of the value.
This removes our need for linux/irqchip/mips-gic.h & prepares us for it
to be removed.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The linux/irqchip/mips-gic.h header is now almost empty. Move the
declarations of gic_get_c0_compare_int(), gic_get_c0_perfcount_int() &
gic_get_c0_fdc_int() to asm/mips-gic.h in order to close in on being
able to delete the former header.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing uses the global gic_present variable anymore; mips_gic_present()
should be used instead. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17045/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In preparation for removing the gic_present global variable, switch to
using the mips_gic_present() function instead. For the most part this is
a straightforward substitution. In cases which previously wrapped the
GIC case in an #ifdef CONFIG_MIPS_GIC that #ifdef has been removed,
since mips_gic_present() will return a compile-time constant false
allowing the affected code to be optimised out anyway.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All in-tree platforms now probe the GIC driver using device tree, and as
such nothing calls gic_init() any longer. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17043/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We provide a forward declaration of the __gic_irq_dispatch() function
for no apparent reason. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17042/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS VDSO code is no longer reliant upon the irqchip driver to
provide the address of the GIC's user-visible section via
gic_get_usm_range(). Remove the now-dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We don't really need gic_get_usm_range() to abstract discovery of the
address of the GIC user-visible section now that we have access to its
base address globally.
Switch to calculating it ourselves, which will allow us to stop
requiring the irqchip driver to care about a counter exposed to userland
for use via the VDSO.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17040/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the definitions of macros used to convert between hardware IRQ
numbers & shared or local interrupt numbers into the irqchip driver,
which is all that should ever need to care about them.
Remove GIC_CPU_TO_VEC_OFFSET() in the process since it's never used.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The GIC_CPU_INT* macros are never used. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17038/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the definition of VP-local interrupts provided by the MIPS Global
Interrupt Controller to the new asm/mips-gic.h header to be alongside
the new accessor functions. Whilst at it, convert to an enum which lends
itself more easily to expansion & documentation.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17037/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC VP-local &
VP-other register blocks to use the new accessor functions provided by
asm/mips-gic.h, resulting in code which is often shorter & easier to
read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17036/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the new accessor functions provided by asm/mips-gic.h to access
masks controlling local interrupts, resulting in code which is often
shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert the remaining accesses to registers in the GIC shared register
block to use the new accessor functions provided by asm/mips-gic.h,
resulting in code which is often shorter & easier to read.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_vpe() function in favour of using the new
write_gic_map_vp() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_map_to_pin() function in favour of using the new
write_gic_map_pin() accessor function which isn't any more complex to
use & allows us to drop a level of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_dual_edge() function in favour of using the new
change_gic_dual() accessor function which provides equivalent
functionality. This also allows us to remove the gic_update_bits()
function which gic_set_dual_edge() was the last user of, along with the
GIC_INTR_OFS() & GIC_INTR_BIT() macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17031/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_trigger() function in favour of using the new
change_gic_trig() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17030/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the gic_set_polarity() function in favour of using the new
change_gic_pol() accessor function which provides equivalent
functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17029/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gic_set_mask() & gic_reset_mask() functions are now no more
convenient to call than the write_gic_smask() or write_gic_rmask()
accessor functions. Remove the layer of abstraction.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17028/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify gic_local_irq_domain_map() by:
- Moving the check for invalid IRQs outside of the loop.
- Moving the decision about whether to use gic_cpu_pin or timer_cpu_pin
outside of the loop.
- Using the new write_gic_vo_map() accessor function to avoid the need
to handle each map register separately.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17027/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Simplify the reads of the bitmaps indicating pending & masked interrupts
in gic_handle_shared_int() using the __ioread32_copy() &
__ioread64_copy() helper functions.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17026/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We currently have __ioread32_copy, __iowrite32_copy & __iowrite64_copy
helpers in lib/iomap_copy.c. This patch adds __ioread64_copy to round
out the set, allowing copies from I/O memory using 32 or 64 bit reads.
[ralf@linux-mips.org: Changed to move all the code of this patch to be
applied to arch/mips temporarily.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17025/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing needs gic_read_local_vp_id() any longer, so remove the dead
code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17024/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than calling the gic_read_local_vp_id() function from the GIC
irqchip driver, call read_gic_vl_ident() to read the GIC_VL_IDENT
register directly. This will allow us to remove gic_read_local_vp_id()
from the irqchip driver in a further patch, since that driver doesn't
actually care about the register's value.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17023/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS GIC clocksource driver is no longer using the accessor
functions provided by the irqchip driver, so remove them.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17022/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the accessor functions provided by asm/mips-gic.h rather than
calling functions provided by the GIC irqchip driver, in preparation for
those non-IRQ-related functions being removed from the irqchip driver.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Switch from calling functions exported by the GIC interrupt controller
to using new accessors provided by asm/mips-gic.h. This will allow the
counter-handling functionality to be removed from the interrupt
controller driver, where it doesn't really belong, and also allow for
inlining of the accesses to the GIC.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17021/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces a new header providing accessor functions for the
MIPS Global Interrupt Controller (GIC) mirroring those provided for the
other 2 components of the MIPS Coherent Processing System (CPS) - the
Coherence Manager (CM) & Cluster Power Controller (CPC).
This header makes use of the new standardised CPS accessor macros where
possible, but does require some custom accessors for cases where we have
either a bit or a register per interrupt.
A major advantage of this over the existing
include/linux/irqchip/mips-gic.h definitions is that code performing
accesses can become much simpler, for example this:
gic_update_bits(GIC_REG(SHARED, GIC_SH_SET_TRIGGER) +
GIC_INTR_OFS(intr), 1ul << GIC_INTR_BIT(intr),
(unsigned long)trig << GIC_INTR_BIT(intr));
...can become simply:
change_gic_trig(intr, trig);
The accessors handle 32 vs 64 bit in the same way as for CM & CPC code,
which means that GIC code will also not need to worry about the access
size in most cases. They are also accessible outside of
drivers/irqchip/irq-mips-gic.c which will allow for simplification in
the use of the non-interrupt portions of the GIC (eg. counters) which
currently require the interrupt controller driver to expose helper
functions for access.
This patch doesn't change any existing code over to use the new
accessors yet, since a wholesale change would be invasive & difficult to
review. Instead follow-on patches will convert code piecemeal to use
this new header. The one change to existing code is to rename gic_base
to mips_gic_base & make it global, in order to fit in with the naming
expected by the standardised CPS accessor macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17020/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A SYNC is required between enabling the GIC region and actually trying
to use it, even if the first access is a read, otherwise its possible
depending on the timing (and in my case depending on the precise
alignment of certain kernel code) to hit CM bus errors on that first
access.
Add the SYNC straight after setting the GIC base.
[paul.burton@imgtec.com:
Changes later in this series increase our likelihood of hitting this
by reducing the amount of code that runs between enabling the GIC &
accessing it.]
Fixes: a7057270c2 ("irqchip: mips-gic: Add device-tree support")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In generic_defconfig set CONFIG_NR_CPUS to 16 rather than 2, which is a
rather too low limit for many modern day MIPS systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16949/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Leave CONFIG_USB_SUPPORT at its default, allowing board config fragments
to make use of USB drivers without needing to override it & trigger
warnings from merge_config.sh.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On systems that support MT ASE multithreading (ie. VPEs) we are very
likely to want to include that support as default. Rather than setting
it in various defconfigs, simply make CONFIG_MIPS_MT_SMP default y such
that systems which select CONFIG_SYS_SUPPORTS_MULTITHREADING get it by
default.
As well as allowing us to remove the selection of CONFIG_MIPS_MT_SMP
from various defconfigs, this also allows the generated generic
defconfigs which derive from generic_defconfig to automatically gain
support for MT ASE SMP when building for a suitable (pre-MIPSr6) ISA.
For malta_kvm_guest_defconfig CONFIG_MIPS_MT_SMP is explicitly disabled
since enabling SMP implicitly disables CONFIG_KVM_GUEST, which depends
on CONFIG_BROKEN_ON_SMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16947/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using generic_defconfig directly is unlikely to be what a user actually
wants to do - it doesn't specify any particular ISA revision & it
doesn't enable any board or driver support, resulting in a largely
useless kernel.
Prevent users from using it directly, printing a helpful message to
point them in the right direction if they attempt to.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16946/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The NI 169445 board uses a little endian MIPS32r2 CPU, and therefore
including board support in kernels that are unable to run on such a CPU
is pointless.
Specify requirements in the board config fragment that cause the NI
169445 board support to only be included in generic kernels that target
little endian MIPS32r2 CPUs.
For example, NI 169445 support will be included when configuring using
32r2el_defconfig but not when using 64r6_defconfig.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Nathan Sullivan <nathan.sullivan@ni.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16945/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS SEAD-3 development board has only ever been used with 32 bit
CPUs, so including support for it in 64 bit kernels is wasteful since
those kernels will never run on a SEAD-3.
Specify a requirement in the SEAD-3 board config fragment that ensures
the board support is only included in 32 bit kernels, by checking that
CONFIG_32BIT=y.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16944/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Up until now when configuring a generic kernel all board config
fragments have been merged by default unless boards are explicitly
selected by the user specifying BOARDS=.
In many cases this is sub-optimal, since some boards don't make sense to
include in some kernels. For example the MIPS SEAD-3 development board
has only ever been used with 32 bit CPUs, so including support for the
SEAD-3 in a 64 bit kernel is wasteful.
This patch introduces support for specifying requirements in board
config fragments, using comments formatted like so:
# require CONFIG_BLA=y
For example the SEAD-3 board could specify that it should only be merged
for 32 bit kernels using a requirement line like the following:
# require CONFIG_32BIT=y
A new generic-board-config.sh script is introduced to handle selecting
the board config fragments to merge & calling merge_config.sh to merge
them. In order to allow requirements to check Kconfig symbols that are
implicitly selected, rather than explicitly specified by
generic_defconfig or one of the ISA config fragments, an intermediate
.config file is saved & used as a reference when checking requirements.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16943/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As a first step towards supporting multi-cluster systems, detect cores &
VPs in secondary clusters & record their cluster information in the
cpu_data array. The "VP topology" line printed during boot is extended
to display multiple clusters. On a single cluster it shows output like
the following:
VP topology: {4,4}
This would indicate a system with 2 cores which each contain 4 VPs. We
extend this to cover multiple clusters in a natural way:
VP topology: {4,4},{2,2}
This would indicate a system with 2 clusters. The first cluster contains
2 cores which each contain 4 VPs. The second cluster contains 2 cores
which each contain 2 VPs.
Actually booting these cores & VPs is left to further patches once other
pieces are in place.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17017/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Modify the functions we use to read information about the topology of
the system (the number of cores, VPs & IOCUs that it contains) in order
to take into account multiple clusters, and provide a new function to
determine the number of clusters in the system.
Users of these functions are modified only such that they continue to
build successfully - having them actually handle multiple clusters is
left to further patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17016/
Patchwork: https://patchwork.linux-mips.org/patch/17218/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With Coherence Manager (CM) 3.5 information about the topology of the
system, which has previously only been available through & accessed from
the CM, is now also provided by the Cluster Power Controller (CPC). This
includes a new CPC_CONFIG register mirroring GCR_CONFIG, and similarly a
new CPC_Cx_CONFIG register mirroring GCR_Cx_CONFIG.
In preparation for adjusting functions such as mips_cm_numcores(), which
have previously only needed to access the CM, to also access the CPC
this patch modifies the way we use the various CPS headers. Rather than
having users include asm/mips-cm.h or asm/mips-cpc.h individually we
instead have users include asm/mips-cps.h which in turn includes
asm/mips-cm.h & asm/mips-cpc.h. This means that users will gain access
to both CM & CPC registers by including one header, and most importantly
it makes asm/mips-cps.h an ideal location for helper functions which
need to access the various components of the CPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17015/
Patchwork: https://patchwork.linux-mips.org/patch/17217/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow the boot_secondary SMP op to return an error to __cpu_up(), which
will in turn return it to its caller.
This will allow SMP implementations to return errors quickly in cases
they they know have failed, rather than relying upon __cpu_up()
eventually timing out waiting for the cpu_running completion.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17014/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With CM >= 3.5 we have the notion of multiple clusters & can access
their CM, CPC & GIC registers via the apporpriate redirect/other
register blocks. In order to allow for this introduce cluster & block
arguments to mips_cm_lock_other() which configures the redirect/other
region to point at the appropriate cluster, core, VP & register block.
Since we now have 4 arguments to mips_cm_lock_other() & a common use is
likely to be to target the cluster, core & VP corresponding to a
particular Linux CPU number we also add a new mips_cm_lock_other_cpu()
helper function which handles that without the caller needing to
manually pull out the cluster, core & VP numbers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17013/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce cpu_cluster() & cpu_set_cluster() accessor functions in the
same vein as cpu_core(), cpu_vpe_id() & their set variants. These will
be used in further patches to allow users to get or set a CPUs cluster
number.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17012/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Up until now we have open-coded checks for whether CPUs are siblings,
with slight variations on whether we consider the package ID or not.
This will only get more complex when we introduce cluster support, so in
preparation for that this patch introduces a cpus_are_siblings()
function which can be used to check whether or not 2 CPUs are siblings
in a consistent manner.
By checking globalnumber with the VP ID masked out this also has the
neat side effect of being ready for multi-cluster systems already.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17011/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch modifies the way we store core & VP IDs such that we store
them in a single 32 bit integer whose format matches that of the MIPSr6
GlobalNumber register. Whereas we have previously stored core & VP IDs
in separate fields, storing them in a single GlobalNumber-like field:
1) Reduces the size of struct cpuinfo_mips by 4 bytes, and will allow
it to not grow when cluster support is added.
2) Gives us a natural place to store cluster number, which matches up
with what the architecture provides.
3) Will be useful in the future as a parameter to the MIPSr6 GINVI
instruction to specify a target CPU whose icache that instruction
should operate on.
The cpu_set*() accessor functions are moved out of the asm/cpu-info.h
header in order to allow them to use the WARN_ON macro, which is
unusable in asm/cpu-info.h due to include ordering.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17010/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We currently have fields in struct cpuinfo_mips for the core & VP(E) ID
of a particular CPU, and various pieces of code directly access those
fields. This patch abstracts such access by introducing accessor
functions cpu_core(), cpu_set_core(), cpu_vpe_id() & cpu_set_vpe_id()
and having code that needs to access these values call those functions
rather than directly accessing the struct cpuinfo_mips fields. This
prepares us for changes to the way in which those values are stored in
later patches.
The cpu_vpe_id() function is introduced even though we already had a
cpu_vpe_id() macro for a couple of reasons:
1) It's more consistent with the core, and future cluster, accessors.
2) It ensures a sensible return type without explicit casts.
3) It's generally preferable to use functions rather than macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17009/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We now have definitions for the GlobalNumber register in asm/mipsregs.h,
so use them in place of magic numbers in cps-vec.S.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17008/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPSr6 introduces a GlobalNumber register, which is required when VPs
are implemented (ie. when multi-threading is supported) but otherwise
optional. The register contains sufficient information to uniquely
identify a VP within a system using its cluster number, core number & VP
ID.
In preparation for using this register & its fields, introduce an
accessor macro for it & define its various bits with the typical style
preprocessor macros.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Introduce definitions & accessors for a selection of Coherence Manager
(CM) & Cluster Power Controller (CPC) registers that are new with CM
v3.5 & the MIPS I6500. These are primarily registers that will be used
in supporting multiple CPU clusters.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17006/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
