We need to be careful and always zero the whole br_ip struct when it is
used for matching since the rhashtable change. This patch fixes all the
places which didn't properly clear it which in turn might've caused
mismatches.
Thanks for the great bug report with reproducing steps and bisection.
Steps to reproduce (from the bug report):
ip link add br0 type bridge mcast_querier 1
ip link set br0 up
ip link add v2 type veth peer name v3
ip link set v2 master br0
ip link set v2 up
ip link set v3 up
ip addr add 3.0.0.2/24 dev v3
ip netns add test
ip link add v1 type veth peer name v1 netns test
ip link set v1 master br0
ip link set v1 up
ip -n test link set v1 up
ip -n test addr add 3.0.0.1/24 dev v1
# Multicast receiver
ip netns exec test socat
UDP4-RECVFROM:5588,ip-add-membership=224.224.224.224:3.0.0.1,fork -
# Multicast sender
echo hello | nc -u -s 3.0.0.2 224.224.224.224 5588
Reported-by: liam.mcbirnie@boeing.com
Fixes: 19e3a9c90c ("net: bridge: convert multicast to generic rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BITS_TO_LONGS() uses DIV_ROUND_UP() because of
this ppmax value can be greater than available
per cpu page pods.
This patch removes BITS_TO_LONGS() to fix this
issue.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Way back in 3c9c36bced the
ndo_fcoe_get_wwn pointer was switched from depending on CONFIG_FCOE to
CONFIG_LIBFCOE in order to allow building FCoE support into the bnx2x
driver and used by bnx2fc without including the generic software fcoe
module.
But, FCoE is generally used over an 802.1q VLAN, and the implementation
of ndo_fcoe_get_wwn in the 8021q module was not similarly changed. The
result is that if CONFIG_FCOE is disabled, then bnz2fc cannot make a
call to ndo_fcoe_get_wwn through the 8021q interface to the underlying
bnx2x interface. The bnx2fc driver then falls back to a potentially
different mapping of Ethernet MAC to Fibre Channel WWN, creating an
incompatibility with the fabric and target configurations when compared
to the WWNs used by pre-boot firmware and differently-configured
kernels.
So make the conditional inclusion of FCoE code in 8021q match the
conditional inclusion in netdevice.h
Signed-off-by: Chris Leech <cleech@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-04-04
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Batch of fixes to the existing BPF flow dissector API to support
calling BPF programs from the eth_get_headlen context (support for
latter is planned to be added in bpf-next), from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen says:
====================
sched: A few small fixes for sch_cake
Kevin noticed a few issues with the way CAKE reads the skb protocol and the IP
diffserv fields. This series fixes those two issues, and should probably go to
in 4.19 as well. However, the previous refactoring patch means they don't apply
as-is; I can send a follow-up directly to stable if that's OK with you?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is not actually any guarantee that the IP headers are valid before we
access the DSCP bits of the packets. Fix this using the same approach taken
in sch_dsmark.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using skb->protocol directly as that will miss cases with
hardware-accelerated VLAN tags. Use the helper instead to get the right
protocol number.
Reported-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8257 §3.5 explicitly states that "A DCTCP sender MUST react to
loss episodes in the same way as conventional TCP".
Currently, Linux DCTCP performs no cwnd reduction when losses
are encountered. Optionally, the dctcp_clamp_alpha_on_loss resets
alpha to its maximal value if a RTO happens. This behavior
is sub-optimal for at least two reasons: i) it ignores losses
triggering fast retransmissions; and ii) it causes unnecessary large
cwnd reduction in the future if the loss was isolated as it resets
the historical term of DCTCP's alpha EWMA to its maximal value (i.e.,
denoting a total congestion). The second reason has an especially
noticeable effect when using DCTCP in high BDP environments, where
alpha normally stays at low values.
This patch replace the clamping of alpha by setting ssthresh to
half of cwnd for both fast retransmissions and RTOs, at most once
per RTT. Consequently, the dctcp_clamp_alpha_on_loss module parameter
has been removed.
The table below shows experimental results where we measured the
drop probability of a PIE AQM (not applying ECN marks) at a
bottleneck in the presence of a single TCP flow with either the
alpha-clamping option enabled or the cwnd halving proposed by this
patch. Results using reno or cubic are given for comparison.
| Link | RTT | Drop
TCP CC | speed | base+AQM | probability
==================|=========|==========|============
CUBIC | 40Mbps | 7+20ms | 0.21%
RENO | | | 0.19%
DCTCP-CLAMP-ALPHA | | | 25.80%
DCTCP-HALVE-CWND | | | 0.22%
------------------|---------|----------|------------
CUBIC | 100Mbps | 7+20ms | 0.03%
RENO | | | 0.02%
DCTCP-CLAMP-ALPHA | | | 23.30%
DCTCP-HALVE-CWND | | | 0.04%
------------------|---------|----------|------------
CUBIC | 800Mbps | 1+1ms | 0.04%
RENO | | | 0.05%
DCTCP-CLAMP-ALPHA | | | 18.70%
DCTCP-HALVE-CWND | | | 0.06%
We see that, without halving its cwnd for all source of losses,
DCTCP drives the AQM to large drop probabilities in order to keep
the queue length under control (i.e., it repeatedly faces RTOs).
Instead, if DCTCP reacts to all source of losses, it can then be
controlled by the AQM using similar drop levels than cubic or reno.
Signed-off-by: Koen De Schepper <koen.de_schepper@nokia-bell-labs.com>
Signed-off-by: Olivier Tilmans <olivier.tilmans@nokia-bell-labs.com>
Cc: Bob Briscoe <research@bobbriscoe.net>
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <borkmann@iogearbox.net>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu says:
====================
net: hns: bugfixes for HNS Driver
This patchset fix some bugs that were found in the test of
various scenarios, or identify by KASAN/sparse.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some sparse warnings in the HNS drivers:
warning: incorrect type in assignment (different address spaces)
expected void [noderef] <asn:2> *io_base
got void *vaddr
warning: cast removes address space '<asn:2>' of expression
[...]
Add __iomem and change all the u8 __iomem to void __iomem to
fix these kind of warnings.
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:2> *base
got unsigned char [usertype] *base_addr
warning: cast to restricted __le16
warning: incorrect type in assignment (different base types)
expected unsigned int [usertype] tbl_tcam_data_high
got restricted __le32 [usertype]
warning: cast to restricted __le32
[...]
These variables used u32/u16 as their type, and finally as a
parameter of writel(), writel() will do the cpu_to_le32 coversion
so remove the little endian covert code to fix these kind of warnings.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP6 neighbor solicitation messages will be discard by the Hip06
chips, because of not setting forwarding pool. Enable promisc mode
has the same problem.
This patch fix the wrong forwarding table configs for the multicast
vague matching when enable promisc mode, and add forwarding pool
for the forwarding table.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HNS driver loaded, always have an error print:
"netif_napi_add() called with weight 256"
This is because the kernel checks the NAPI polling weights
requested by drivers and it prints an error message if a driver
requests a weight bigger than 64.
So use NAPI_POLL_WEIGHT to fix it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is trying to fix the issue due to:
[27237.844750] BUG: KASAN: use-after-free in hns_nic_net_xmit_hw+0x708/0xa18[hns_enet_drv]
After hnae_queue_xmit() in hns_nic_net_xmit_hw(), can be
interrupted by interruptions, and than call hns_nic_tx_poll_one()
to handle the new packets, and free the skb. So, when turn back to
hns_nic_net_xmit_hw(), calling skb->len will cause use-after-free.
This patch update tx ring statistics in hns_nic_tx_poll_one() to
fix the bug.
Signed-off-by: Liubin Shu <shuliubin@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename bpf_flow_dissector.txt to bpf_flow_dissector.rst and fix
formatting. Also, link it from the Documentation/networking/index.rst.
Tested with 'make htmldocs' to make sure it looks reasonable.
Fixes: ae82899bbe ("flow_dissector: document BPF flow dissector environment")
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
At the beginning of ip6_fragment func, the prevhdr pointer is
obtained in the ip6_find_1stfragopt func.
However, all the pointers pointing into skb header may change
when calling skb_checksum_help func with
skb->ip_summed = CHECKSUM_PARTIAL condition.
The prevhdr pointe will be dangling if it is not reloaded after
calling __skb_linearize func in skb_checksum_help func.
Here, I add a variable, nexthdr_offset, to evaluate the offset,
which does not changes even after calling __skb_linearize func.
Fixes: 405c92f7a5 ("ipv6: add defensive check for CHECKSUM_PARTIAL skbs in ip_fragment")
Signed-off-by: Junwei Hu <hujunwei4@huawei.com>
Reported-by: Wenhao Zhang <zhangwenhao8@huawei.com>
Reported-by: syzbot+e8ce541d095e486074fc@syzkaller.appspotmail.com
Reviewed-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we may merge incorrectly a received GSO packet
or a packet with frag_list into a packet sitting in the
gro_hash list. skb_segment() may crash case because
the assumptions on the skb layout are not met.
The correct behaviour would be to flush the packet in the
gro_hash list and send the received GSO packet directly
afterwards. Commit d61d072e87 ("net-gro: avoid reorders")
sets NAPI_GRO_CB(skb)->flush in this case, but this is not
checked before merging. This patch makes sure to check this
flag and to not merge in that case.
Fixes: d61d072e87 ("net-gro: avoid reorders")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanislav Fomichev says:
====================
This patch series fixes the existing BPF flow dissector API to
support calling BPF progs from the eth_get_headlen context (the
support itself will be added in bpf-next tree).
The summary of the changes:
* fix VLAN handling in bpf_flow.c, we don't need to peek back and look
at skb->vlan_present; add selftests
* pass and use flow_keys->n_proto instead of skb->protocol
* fix clamping of flow_keys->nhoff for packets with nhoff > 0
* prohibit access to most of the __sk_buff fields from BPF flow
dissector progs; only data/data_end/flow_keys are allowed (all input
is now passed via flow_keys)
* finally, document BPF flow dissector program environment
====================
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Petar Penkov <peterpenkov96@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Short doc on what BPF flow dissector should expect in the input
__sk_buff and flow_keys.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Use whitelist instead of a blacklist and allow only a small set of
fields that might be relevant in the context of flow dissector:
* data
* data_end
* flow_keys
This is required for the eth_get_headlen case where we have only a
chunk of data to dissect (i.e. trying to read the other skb fields
doesn't make sense).
Note, that it is a breaking API change! However, we've provided
flow_keys->n_proto as a substitute for skb->protocol; and there is
no need to manually handle skb->vlan_present. So even if we
break somebody, the migration is trivial. Unfortunately, we can't
support eth_get_headlen use-case without those breaking changes.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Don't allow BPF program to set flow_keys->nhoff to less than initial
value. We currently don't read the value afterwards in anything but
the tests, but it's still a good practice to return consistent
values to the test programs.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This is a preparation for the next commit that would prohibit access to
the most fields of __sk_buff from the BPF programs.
Instead of requiring BPF flow dissector programs to look into skb,
pass all input data in the flow_keys.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When we tail call PROG(VLAN) from parse_eth_proto we don't need to peek
back to handle vlan proto because we didn't adjust nhoff/thoff yet. Use
flow_keys->n_proto, that we set in parse_eth_proto instead and
properly increment nhoff as well.
Also, always use skb->protocol and don't look at skb->vlan_present.
skb->vlan_present indicates that vlan information is stored out-of-band
in skb->vlan_{tci,proto} and vlan header is already pulled from skb.
That means, skb->vlan_present == true is not relevant for BPF flow
dissector.
Add simple test cases with VLAN tagged frames:
* single vlan for ipv4
* double vlan for ipv6
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-04-01
This series contains two fixes for XDP in the i40e driver.
Björn provides both fixes, first moving a function out of the header and
into the main.c file. Second fixes a regression introduced in an
earlier patch that removed umem from the VSI. This caused an issue
because the setup code would try to enable AF_XDP zero copy
unconditionally, as long as there was a umem placed in the netdev
receive structure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The device type for ip6 tunnels is set to
ARPHRD_TUNNEL6. However, the ip4ip6_err function
is expecting the device type of the tunnel to be
ARPHRD_TUNNEL. Since the device types do not
match, the function exits and the ICMP error
packet is not sent to the originating host. Note
that the device type for IPv4 tunnels is set to
ARPHRD_TUNNEL.
Fix is to expect a tunnel device type of
ARPHRD_TUNNEL6 instead. Now the tunnel device
type matches and the ICMP error packet is sent
to the originating host.
Signed-off-by: Sheena Mira-ato <sheena.mira-ato@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dccp_feat_push_change fails, we forget free the mem
which is alloced by kmemdup in dccp_feat_clone_sp_val.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e8ef967a54 ("dccp: Registration routines for changing feature values")
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot report a kernel-infoleak:
BUG: KMSAN: kernel-infoleak in _copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
Call Trace:
_copy_to_user+0x16b/0x1f0 lib/usercopy.c:32
copy_to_user include/linux/uaccess.h:174 [inline]
sctp_getsockopt_peer_addrs net/sctp/socket.c:5911 [inline]
sctp_getsockopt+0x1668e/0x17f70 net/sctp/socket.c:7562
...
Uninit was stored to memory at:
sctp_transport_init net/sctp/transport.c:61 [inline]
sctp_transport_new+0x16d/0x9a0 net/sctp/transport.c:115
sctp_assoc_add_peer+0x532/0x1f70 net/sctp/associola.c:637
sctp_process_param net/sctp/sm_make_chunk.c:2548 [inline]
sctp_process_init+0x1a1b/0x3ed0 net/sctp/sm_make_chunk.c:2361
...
Bytes 8-15 of 16 are uninitialized
It was caused by that th _pad field (the 8-15 bytes) of a v4 addr (saved in
struct sockaddr_in) wasn't initialized, but directly copied to user memory
in sctp_getsockopt_peer_addrs().
So fix it by calling memset(addr->v4.sin_zero, 0, 8) to initialize _pad of
sockaddr_in before copying it to user memory in sctp_v4_addr_to_user(), as
sctp_v6_addr_to_user() does.
Reported-by: syzbot+86b5c7c236a22616a72f@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Tested-by: Alexander Potapenko <glider@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: flower: fix matching and pushing vlan CFI bit
This patch clears up some confusion around the meaning of bit 12
for FW messages related to VLAN and flower offload.
Pieter says:
It fixes issues with matching, pushing and popping vlan tags.
We replace the vlan CFI bit with a vlan present bit that
indicates the presence of a vlan tag. We also no longer set
the CFI when pushing vlan tags.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer set CFI when pushing vlan tags, therefore we remove
the CFI bit from push vlan.
Fixes: 1a1e586f54 ("nfp: add basic action capabilities to flower offloads")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace vlan CFI bit with a vlan present bit that indicates the
presence of a vlan tag. Previously the driver incorrectly assumed
that an vlan id of 0 is not matchable, therefore we indicate vlan
presence with a vlan present bit.
Fixes: 5571e8c9f2 ("nfp: extend flower matching capabilities")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Louis Peens <louis.peens@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When kcm is loaded while many processes try to create a KCM socket, a
crash occurs:
BUG: unable to handle kernel NULL pointer dereference at 000000000000000e
IP: mutex_lock+0x27/0x40 kernel/locking/mutex.c:240
PGD 8000000016ef2067 P4D 8000000016ef2067 PUD 3d6e9067 PMD 0
Oops: 0002 [#1] SMP KASAN PTI
CPU: 0 PID: 7005 Comm: syz-executor.5 Not tainted 4.12.14-396-default #1 SLE15-SP1 (unreleased)
RIP: 0010:mutex_lock+0x27/0x40 kernel/locking/mutex.c:240
RSP: 0018:ffff88000d487a00 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 000000000000000e RCX: 1ffff100082b0719
...
CR2: 000000000000000e CR3: 000000004b1bc003 CR4: 0000000000060ef0
Call Trace:
kcm_create+0x600/0xbf0 [kcm]
__sock_create+0x324/0x750 net/socket.c:1272
...
This is due to race between sock_create and unfinished
register_pernet_device. kcm_create tries to do "net_generic(net,
kcm_net_id)". but kcm_net_id is not initialized yet.
So switch the order of the two to close the race.
This can be reproduced with mutiple processes doing socket(PF_KCM, ...)
and one process doing module removal.
Fixes: ab7ac4eb98 ("kcm: Kernel Connection Multiplexor module")
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni says:
====================
net: sched: fix stats accounting for child NOLOCK qdiscs
Currently, stats accounting for NOLOCK qdisc enslaved to classful (lock)
qdiscs is buggy. Per CPU values are ignored in most places, as a result,
stats dump in the above scenario always report 0 length backlog and parent
backlog len is not updated correctly on NOLOCK qdisc removal.
The first patch address stats dumping, and the second one child qdisc removal.
I'm targeting the net tree as this is a bugfix, but it could be moved to
net-next due to the relatively large diffstat.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code to flush qdisc tree and purge the qdisc queue
is duplicated in many places and in most cases it does not
respect NOLOCK qdisc: the global backlog len is used and the
per CPU values are ignored.
This change addresses the above, factoring-out the relevant
code and using the helpers introduced by the previous patch
to fetch the correct backlog len.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Classful qdiscs can't access directly the child qdiscs backlog
length: if such qdisc is NOLOCK, per CPU values should be
accounted instead.
Most qdiscs no not respect the above. As a result, qstats fetching
for most classful qdisc is currently incorrect: if the child qdisc is
NOLOCK, it always reports 0 len backlog.
This change introduces a pair of helpers to safely fetch
both backlog and qlen and use them in stats class dumping
functions, fixing the above issue and cleaning a bit the code.
DRR needs also to access the child qdisc queue length, so it
needs custom handling.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It returned always NULL, thus it was never possible to get the filter.
Example:
$ ip link add foo type dummy
$ ip link add bar type dummy
$ tc qdisc add dev foo clsact
$ tc filter add dev foo protocol all pref 1 ingress handle 1234 \
matchall action mirred ingress mirror dev bar
Before the patch:
$ tc filter get dev foo protocol all pref 1 ingress handle 1234 matchall
Error: Specified filter handle not found.
We have an error talking to the kernel
After:
$ tc filter get dev foo protocol all pref 1 ingress handle 1234 matchall
filter ingress protocol all pref 1 matchall chain 0 handle 0x4d2
not_in_hw
action order 1: mirred (Ingress Mirror to device bar) pipe
index 1 ref 1 bind 1
CC: Yotam Gigi <yotamg@mellanox.com>
CC: Jiri Pirko <jiri@mellanox.com>
Fixes: fd62d9f5c5 ("net/sched: matchall: Fix configuration race")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit f3fef2b6e1 ("i40e: Remove umem from VSI") a regression was
introduced; When the VSI was reset, the setup code would try to enable
AF_XDP ZC unconditionally (as long as there was a umem placed in the
netdev._rx struct). Here, we add a bitmap to the VSI that tracks if a
certain queue pair has been "zero-copy enabled" via the ndo_bpf. The
bitmap is used in i40e_xsk_umem, and enables zero-copy if and only if
XDP is enabled, the corresponding qid in the bitmap is set and the
umem is non-NULL.
Fixes: f3fef2b6e1 ("i40e: Remove umem from VSI")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_xsk_umem function was explicitly inlined in i40e.h. There is
no reason for that, so move it to i40e_main.c instead.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Configuration check to accept source route IP options should be made on
the incoming netdevice when the skb->dev is an l3mdev master. The route
lookup for the source route next hop also needs the incoming netdev.
v2->v3:
- Simplify by passing the original netdevice down the stack (per David
Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Martin Habets <mhabets@solarflare.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When tcp_sk_init() failed in inet_ctl_sock_create(),
'net->ipv4.tcp_congestion_control' will be left
uninitialized, but tcp_sk_exit() hasn't check for
that.
This patch add checking on 'net->ipv4.tcp_congestion_control'
in tcp_sk_exit() to prevent NULL-ptr dereference.
Fixes: 6670e15244 ("tcp: Namespace-ify sysctl_tcp_default_congestion_control")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
tipc: a batch of uninit-value fixes for netlink_compat
These issues were all reported by syzbot, and exist since very beginning.
See the details on each patch.
====================
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot found a crash:
BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x54f/0xcd0 net/tipc/netlink_compat.c:872
Call Trace:
tipc_nl_compat_name_table_dump+0x54f/0xcd0 net/tipc/netlink_compat.c:872
__tipc_nl_compat_dumpit+0x59e/0xda0 net/tipc/netlink_compat.c:215
tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:280
tipc_nl_compat_handle net/tipc/netlink_compat.c:1226 [inline]
tipc_nl_compat_recv+0x1b5f/0x2750 net/tipc/netlink_compat.c:1265
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
Uninit was created at:
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline]
netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
It was supposed to be fixed on commit 974cb0e3e7 ("tipc: fix uninit-value
in tipc_nl_compat_name_table_dump") by checking TLV_GET_DATA_LEN(msg->req)
in cmd->header()/tipc_nl_compat_name_table_dump_header(), which is called
ahead of tipc_nl_compat_name_table_dump().
However, tipc_nl_compat_dumpit() doesn't handle the error returned from cmd
header function. It means even when the check added in that fix fails, it
won't stop calling tipc_nl_compat_name_table_dump(), and the issue will be
triggered again.
So this patch is to add the process for the err returned from cmd header
function in tipc_nl_compat_dumpit().
Reported-by: syzbot+3ce8520484b0d4e260a5@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar issue as fixed by Patch "tipc: check bearer name with right
length in tipc_nl_compat_bearer_enable" was also found by syzbot in
tipc_nl_compat_link_set().
The length to check with should be 'TLV_GET_DATA_LEN(msg->req) -
offsetof(struct tipc_link_config, name)'.
Reported-by: syzbot+de00a87b8644a582ae79@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported the following crash:
BUG: KMSAN: uninit-value in memchr+0xce/0x110 lib/string.c:961
memchr+0xce/0x110 lib/string.c:961
string_is_valid net/tipc/netlink_compat.c:176 [inline]
tipc_nl_compat_bearer_enable+0x2c4/0x910 net/tipc/netlink_compat.c:401
__tipc_nl_compat_doit net/tipc/netlink_compat.c:321 [inline]
tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:354
tipc_nl_compat_handle net/tipc/netlink_compat.c:1162 [inline]
tipc_nl_compat_recv+0x1ae7/0x2750 net/tipc/netlink_compat.c:1265
genl_family_rcv_msg net/netlink/genetlink.c:601 [inline]
genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626
netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477
genl_rcv+0x63/0x80 net/netlink/genetlink.c:637
netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline]
netlink_unicast+0xf3e/0x1020 net/netlink/af_netlink.c:1336
netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
Uninit was created at:
__alloc_skb+0x309/0xa20 net/core/skbuff.c:208
alloc_skb include/linux/skbuff.h:1012 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1182 [inline]
netlink_sendmsg+0xb82/0x1300 net/netlink/af_netlink.c:1892
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg net/socket.c:632 [inline]
It was triggered when the bearer name size < TIPC_MAX_BEARER_NAME,
it would check with a wrong len/TLV_GET_DATA_LEN(msg->req), which
also includes priority and disc_domain length.
This patch is to fix it by checking it with a right length:
'TLV_GET_DATA_LEN(msg->req) - offsetof(struct tipc_bearer_config, name)'.
Reported-by: syzbot+8b707430713eb46e1e45@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aaro Koskinen says:
====================
net: stmmac: fix handling of oversized frames
I accidentally had MTU size mismatch (9000 vs. 1500) in my network,
and I noticed I could kill a system using stmmac & 1500 MTU simply
by pinging it with "ping -s 2000 ...".
While testing a fix I encountered also some other issues that need fixing.
I have tested these only with enhanced descriptors, so the normal
descriptor changes need a careful review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is log is harmful as it can trigger multiple times per packet. Delete
it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets without the last descriptor set should be dropped early. If we
receive a frame larger than the DMA buffer, the HW will continue using the
next descriptor. Driver mistakes these as individual frames, and sometimes
a truncated frame (without the LD set) may look like a valid packet.
This fixes a strange issue where the system replies to 4098-byte ping
although the MTU/DMA buffer size is set to 4096, and yet at the same
time it's logging an oversized packet.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
