The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default Tx rates cause very long ISR delays on Tx.
0xff is 510us delay, giving only ~ 2000 interrupts per seconds for
Tx rings cleanup. With these settings udp tx rate was never higher than
~800Mbps on a single stream. Changing min delay to 0xF makes it
way better with ~6Gbps
TCP stream performance is almost unaffected by this change, since LSO
optimizations play important role.
CPU load is affected insignificantly by this change.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia NIC allows both TX and RX interrupt throttle rate (ITR)
management, but this was used in a very limited way via predefined
values. This patch allows to setup ITR default values via module
command line arguments and via standard ethtool coalescing settings.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That may lead to mmio resource leakage.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no much practical use from having MSIX vectors more that number
of cpus, thus cap this first with preconfigured limit, then with number
of cpus online.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing ifconfig down/up, driver did not reported carrier_off neither
in nic_stop nor in nic_start. That caused link to be visible as "up"
during couple of seconds immediately after "ifconfig up".
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Queue stat strings are cleaned up, duplicate stat name strings removed,
queue restarts counter added
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal statistics system on chip never gets reset until hardware
reboot. This is quite inconvenient in terms of ethtool statistics usage.
This patch implements incremental statistics update inside of
service callback.
Upon nic initialization, first request is done to fetch
initial stat data, current collected stat data gets cleared.
Internal statistics mailbox readout is improved to save space and
increase readability
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On big-endian machines, functions converting between tunnel ID
and VNI use the three LSBs of tunnel ID storage to map VNI.
The comparison function eq_tun_id_and_vni(), on the other hand,
attempted to map the VNI from the three MSBs. Fix it by using
the same check implemented on LE, which maps VNI from the three
LSBs of tunnel ID.
Fixes: 2e0b26e103 ("geneve: Optimize geneve device lookup.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAlnohyMTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9jRFCACmSBz2H1yW5VfjrN3ZgoEoUo8P5qCZ
7mXvTstTASF20T7kFqNS2K94CMVjBYRUIHvihp0LmPmPAmpmQRNedAssWuZpMflw
xhaH8T8YWbyzHU2MBZP9WtTjrTilPEPcjvFSgYw6wpHW7VC3S/ffEN8Mj3ymR6bW
KRw7gemXpvYUxPrGGCzyvFy4G+KptyPcAD6I8ceDUtdkwK4TXGYqEAoSqxtAIUHX
dgRLzheOv8sDh+dM+ZNpH6UUkzK0gVHQ40lgXydZazEwPPq9zdj2Ec/6qpR5fkUH
dnCIhzLNiCJOMGSfzkf0Esef1zBpU8oJmILbgf97CdayaW9cA1EUleGW
=HYTx
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.14-20171019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2017-10-19
this is a pull request of 11 patches for the upcoming 4.14 release.
There are 6 patches by ZHU Yi for the flexcan driver, that work around
the CAN error handling state transition problems found in various
incarnations of the flexcan IP core.
The patch by Colin Ian King fixes a potential NULL pointer deref in the
CAN broad cast manager (bcm). One patch by me replaces a direct deref of a RCU
protected pointer by rcu_access_pointer. My second patch adds missing
OOM error handling in af_can. A patch by Stefan Mätje for the esd_usb2
driver fixes the dlc in received RTR frames. And the last patch is by
Wolfgang Grandegger, it fixes a busy loop in the gs_usb driver in case
it runs out of TX contexts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool ena_get_channels() expose the max number of queues as the max
number of queues ENA supports (128 queues) and not the actual number
of created queues.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Decrease log level of checksum errors as these messages can be
triggered remotely by bad packets.
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If sending messages with no cable connected, it quickly happens that
there is no more TX context available. Then "gs_can_start_xmit()"
returns with "NETDEV_TX_BUSY" and the upper layer does retry
immediately keeping the CPU busy. To fix that issue, I moved
"atomic_dec(&dev->active_tx_urbs)" from "gs_usb_xmit_callback()" to
the TX done handling in "gs_usb_receive_bulk_callback()". Renaming
"active_tx_urbs" to "active_tx_contexts" and moving it into
"gs_[alloc|free]_tx_context()" would also make sense.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The dlc member of the struct rx_msg contains also the ESD_RTR flag to
mark received RTR frames. Without the fix the can_dlc value for received
RTR frames would always be set to 8 by get_can_dlc() instead of the
received value.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable FLEXCAN_QUIRK_BROKEN_WERR_STATE and
FLEXCAN_QUIRK_BROKEN_PERR_STATE for p1010 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX28 to report correct
state transitions, especially to error passive.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable FLEXCAN_QUIRK_BROKEN_PERR_STATE for i.MX6 to report correct state
transitions.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add FLEXCAN_QUIRK_BROKEN_PERR_STATE for better description of the
missing error passive interrupt quirk.
Error interrupt flooding may happen if the broken error state quirk fix
is enabled. For example, in case there is singled out node on the bus
and the node sends a frame, then error interrupt flooding happens and
will not stop because the node cannot go to bus off. The flooding will
stop after another node connected to the bus again.
If high bitrate configured on the low end system, then the flooding
may causes performance issue, hence, this patch mitigates this by:
1. disable error interrupt upon error passive state transition
2. re-enable error interrupt upon error warning state transition
3. disable/enable error interrupt upon error active state transition
depends on FLEXCAN_QUIRK_BROKEN_WERR_STATE
In this way, the driver is still able to report correct state
transitions without additional latency. When there are bus problems,
flooding of error interrupts is limited to the number of frames required
to change state from error warning to error passive if the core has
[TR]WRN_INT connected (FLEXCAN_QUIRK_BROKEN_WERR_STATE is not enabled),
otherwise, the flooding is limited to the number of frames required to
change state from error active to error passive.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename FLEXCAN_QUIRK_BROKEN_ERR_STATE to FLEXCAN_QUIRK_BROKEN_WERR_STATE
for better description of the missing [TR]WRN_INT quirk.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Update state upon any interrupt to report correct state transitions in
case the flexcan core enabled the broken error state quirk fix.
Signed-off-by: Zhu Yi <yi.zhu5@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.11
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch correctly sets the number of additional header descriptors
that will be sent in an indirect SCRQ entry.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an EMAD is transmitted, a timeout work item is scheduled with a
delay of 200ms, so that another EMAD will be retried until a maximum of
five retries.
In certain situations, it's possible for the function waiting on the
EMAD to be associated with a work item that is queued on the same
workqueue (`mlxsw_core`) as the timeout work item. This results in
flushing a work item on the same workqueue.
According to commit e159489baa ("workqueue: relax lockdep annotation
on flush_work()") the above may lead to a deadlock in case the workqueue
has only one worker active or if the system in under memory pressure and
the rescue worker is in use. The latter explains the very rare and
random nature of the lockdep splats we have been seeing:
[ 52.730240] ============================================
[ 52.736179] WARNING: possible recursive locking detected
[ 52.742119] 4.14.0-rc3jiri+ #4 Not tainted
[ 52.746697] --------------------------------------------
[ 52.752635] kworker/1:3/599 is trying to acquire lock:
[ 52.758378] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c4fa4>] flush_work+0x3a4/0x5e0
[ 52.767837]
but task is already holding lock:
[ 52.774360] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.784495]
other info that might help us debug this:
[ 52.791794] Possible unsafe locking scenario:
[ 52.798413] CPU0
[ 52.801144] ----
[ 52.803875] lock(mlxsw_core_driver_name);
[ 52.808556] lock(mlxsw_core_driver_name);
[ 52.813236]
*** DEADLOCK ***
[ 52.819857] May be due to missing lock nesting notation
[ 52.827450] 3 locks held by kworker/1:3/599:
[ 52.832221] #0: (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.842846] #1: ((&(&bridge->fdb_notify.dw)->work)){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.854537] #2: (rtnl_mutex){+.+.}, at: [<ffffffff822ad8e7>] rtnl_lock+0x17/0x20
[ 52.863021]
stack backtrace:
[ 52.867890] CPU: 1 PID: 599 Comm: kworker/1:3 Not tainted 4.14.0-rc3jiri+ #4
[ 52.875773] Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016
[ 52.886267] Workqueue: mlxsw_core mlxsw_sp_fdb_notify_work [mlxsw_spectrum]
[ 52.894060] Call Trace:
[ 52.909122] __lock_acquire+0xf6f/0x2a10
[ 53.025412] lock_acquire+0x158/0x440
[ 53.047557] flush_work+0x3c4/0x5e0
[ 53.087571] __cancel_work_timer+0x3ca/0x5e0
[ 53.177051] cancel_delayed_work_sync+0x13/0x20
[ 53.182142] mlxsw_reg_trans_bulk_wait+0x12d/0x7a0 [mlxsw_core]
[ 53.194571] mlxsw_core_reg_access+0x586/0x990 [mlxsw_core]
[ 53.225365] mlxsw_reg_query+0x10/0x20 [mlxsw_core]
[ 53.230882] mlxsw_sp_fdb_notify_work+0x2a3/0x9d0 [mlxsw_spectrum]
[ 53.237801] process_one_work+0x8f1/0x12f0
[ 53.321804] worker_thread+0x1fd/0x10c0
[ 53.435158] kthread+0x28e/0x370
[ 53.448703] ret_from_fork+0x2a/0x40
[ 53.453017] mlxsw_spectrum 0000:01:00.0: EMAD retries (2/5) (tid=bf4549b100000774)
[ 53.453119] mlxsw_spectrum 0000:01:00.0: EMAD retries (5/5) (tid=bf4549b100000770)
[ 53.453132] mlxsw_spectrum 0000:01:00.0: EMAD reg access failed (tid=bf4549b100000770,reg_id=200b(sfn),type=query,status=0(operation performed))
[ 53.453143] mlxsw_spectrum 0000:01:00.0: Failed to get FDB notifications
Fix this by creating another workqueue for EMAD timeouts, thereby
preventing the situation of a work item trying to flush a work item
queued on the same workqueue.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_send_message() is replaced with _hwrm_send_message(), and
hwrm_cmd_lock mutex lock is grabbed for the whole period of
firmware call until the firmware DCB parameters have been copied.
This will prevent possible corruption of the firmware data.
Fixes: 7df4ae9fe8 ("bnxt_en: Implement DCBNL to support host-based DCBX.")
Signed-off-by: Sankar Patchineelam <sankar.patchineelam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_find_nvram_item(), it is copying firmware response data after
releasing the mutex. This can cause the firmware response data
to be corrupted if the next firmware response overwrites the response
buffer. The rare problem shows up when running ethtool -i repeatedly.
Fix it by calling the new variant _hwrm_send_message_silent() that requires
the caller to take the mutex and to release it after the response data has
been copied.
Fixes: 3ebf6f0a09 ("bnxt_en: Add installed-package version reporting via Ethtool GDRVINFO")
Reported-by: Sarveswara Rao Mygapula <sarveswararao.mygapula@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sriov_enable(), we calculate to see if we have enough hardware
resources to enable the requested number of VFs. The logic to check
for minimum completion rings and statistics contexts is missing. Add
the required checks so that VF configuration won't fail.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCIE PCIE_EP_REG_LINK_STATUS_CONTROL register is only defined in PF
config space, so we must read it from the PF.
Fixes: 90c4f788f6 ("bnxt_en: Report PCIe link speed and width during driver load")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a further improvement to the PF/VF link change logic, use a private
mutex instead of the rtnl lock to protect link change logic. With the
new mutex, we don't have to take the rtnl lock in the workqueue when
we have to handle link related functions. If the VF and PF drivers
are running on the same host and both take the rtnl lock and one is
waiting for the other, it will cause timeout. This patch fixes these
timeouts.
Fixes: 90c694bb71 ("bnxt_en: Fix RTNL lock usage on bnxt_update_link().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link status query firmware messages originating from the VFs are forwarded
to the PF. The driver handles these interactions in a workqueue for the
VF and PF. The VF driver waits for the response from the PF in the
workqueue. If the PF and VF driver are running on the same host and the
work for both PF and VF are queued on the same workqueue, the VF driver
may not get the response if the PF work item is queued behind it on the
same workqueue. This will lead to the VF link query message timing out.
To prevent this, we create a private workqueue for PFs instead of using
the common workqueue. The VF query and PF response will never be on
the same workqueue.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA reset timeout, used in read_poll_timeout, is
ten times shorter than the sleep time.
This patch fixes these values interchanging them, as it was
before the read_poll_timeout introduction.
Fixes: 8a70aeca80 ("net: stmmac: Use readl_poll_timeout")
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While experimenting with changes to the timekeeping code, I
ran into a build error in the liquidio driver:
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'liquidio_ptp_settime':
drivers/net/ethernet/cavium/liquidio/lio_main.c:1850:22: error: passing argument 1 of 'timespec_to_ns' from incompatible pointer type [-Werror=incompatible-pointer-types]
The driver had a type mismatch since it was first merged, but
this never caused problems because it is only built on 64-bit
architectures that define timespec and timespec64 to the same
type.
If we ever want to compile-test the driver on 32-bit or change
the way that 64-bit timespec64 is defined, we need to fix it,
so let's just do it now.
Fixes: f21fb3ed36 ("Add support of Cavium Liquidio ethernet adapters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing really special standing out, all of these are important fixes
which should go to 4.14.
iwlwifi
* fix support for 3168 device series
* fix a potential crash when using FW debugging recording;
* improve channel flags parsing to avoid warnings on too long traces
* return -ENODATA when the temperature is not available, since the
-EIO we were returning was causing fatal errors in userspace
* avoid printing too many messages in dmesg when using monitor mode,
since this can become very noisy and completely flood the logs
brcmsmac
* reduce stack usage to avoid frame size warnings with KASAN
brcmfmac
* add a check to avoid copying uninitialised memory
rtlwifi:
* fix a regression with rtl8821ae starting from v4.11 where
connections was frequently lost
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ4GYHAAoJEG4XJFUm622bXf8H/3DJF5P02OzWIVMK376xUgVI
feX8tsazK0/cCgxeMfp/K4Nb9umZHFTNd1Zs5mrx8DFJjL1ekXTz93GtfcJ+WFH5
sPwS+IVOf4IaBrSiNpqskJhln3GHp7A+eFgqbFQ+Is4/eQQBqt/lW6LZoyA5DI6X
80hOT4eZtHanKNFQHuSgOGHXttAB9AcnEJngvfToZCV1jqadeoPK1GZQ+6Xsot3g
RU5gYxc4gN+d203KhUxEebzz8buyfCEPG1wFze/mazPcQJ+8IJjMNOl474atKslW
dsbqak2gtl70weZHeh2PlYkNvTZbAbiWk9feaTGeuwAgwWDms1BJKUKRppfZdqE=
=RA6K
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-10-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Nothing really special standing out, all of these are important fixes
which should go to 4.14.
iwlwifi
* fix support for 3168 device series
* fix a potential crash when using FW debugging recording;
* improve channel flags parsing to avoid warnings on too long traces
* return -ENODATA when the temperature is not available, since the
-EIO we were returning was causing fatal errors in userspace
* avoid printing too many messages in dmesg when using monitor mode,
since this can become very noisy and completely flood the logs
brcmsmac
* reduce stack usage to avoid frame size warnings with KASAN
brcmfmac
* add a check to avoid copying uninitialised memory
rtlwifi:
* fix a regression with rtl8821ae starting from v4.11 where
connections was frequently lost
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl_init_one() currently enables PCI wakeups if the ethernet device
is found to be WOL-capable. There is no need to do this when
rtl8169_set_wol() will correctly enable or disable the same wakeup flag
when WOL is activated/deactivated.
This works around an ACPI DSDT bug which prevents the Acer laptop models
Aspire ES1-533, Aspire ES1-732, PackardBell ENTE69AP and Gateway NE533
from entering S3 suspend - even when no ethernet cable is connected.
On these platforms, the DSDT says that GPE08 is a wakeup source for
ethernet, but this GPE fires as soon as the system goes into suspend,
waking the system up immediately. Having the wakeup normally disabled
avoids this issue in the default case.
With this change, WOL will continue to be unusable on these platforms
(it will instantly wake up if WOL is later enabled by the user) but we
do not expect this to be a commonly used feature on these consumer
laptops. We have separately determined that WOL works fine without any
ACPI GPEs enabled during sleep, so a DSDT fix or override would be
possible to make WOL work.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: cda7ea6903 ("macsec: check return value of skb_to_sgvec always")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
page_address() does not handle NULL argument gracefully,
make sure we NULL-check the page pointer before passing it
to page_address().
Fixes: ecd63a0217 ("nfp: add XDP support in the driver")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while loop fetching 64 bit ethtool statistics may have
to retry multiple times, it shouldn't modify the outside state.
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-10-10
This series contains updates to i40e only.
Stefano Brivio fixes the grammar in a function header comment.
Alex fixes a memory leak where we were not correctly placing the pages
from buffers that had been used to return a filter programming status
back on the ring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Variable Length Array in Struct (VLAIS) to valid C by converting
local struct definition to use a flexible array. The structure is only
used to define a cast of a buffer so the size of the struct is not used
to allocate storage.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Signed-off-by: Mark Charebois <charlebm@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like we weren't correctly placing the pages from buffers that had
been used to return a filter programming status back on the ring. As a
result they were being overwritten and tracking of the pages was lost.
This change works to correct that by incorporating part of
i40e_put_rx_buffer into the programming status handler code. As a result we
should now be correctly placing the pages for those buffers on the
re-allocation list instead of letting them stay in place.
Fixes: 0e626ff7cc ("i40e: Fix support for flow director programming status")
Reported-by: Anders K. Pedersen <akp@cohaesio.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Anders K Pedersen <akp@cohaesio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Caller needs to acquire the lock. Called functions will not.
Fixes: 09f79fd49d ("i40e: avoid NVM acquire deadlock during NVM update")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The u-blox TOBY-L2 is a LTE Cat 4 module with HSPA+ and 2G fallback.
This module allows switching to different USB profiles with the
'AT+UUSBCONF' command, and provides a ECM network interface when the
'AT+UUSBCONF=2' profile is selected.
The u-blox SARA-U2 is a HSPA module with 2G fallback. The default USB
configuration includes a ECM network interface.
Both these modules are controlled via AT commands through one of the
TTYs exposed. Connecting these modules may be done just by activating
the desired PDP context with 'AT+CGACT=1,<cid>' and then running DHCP
on the ECM interface.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the TX ring parameters with an XDP program attached may
cause the XDP queues to be cleared and the TX rings to be incorrectly
configured.
Fix by doing correct ring accounting in setup call.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe driver use the compile check to determine if it can
send TLPs to Root Port with the Relaxed Ordering Attribute set,
this is too inconvenient, now the new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING
has been added to the kernel and we could check the bit4 in the PCIe
Device Control register to determine whether we should use the Relaxed
Ordering Attributes or not, so use this new way in the ixgbe driver.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.
With this new flag we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76dc ("net:add one common config...") did,
so revert this commit.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.
Fixes: a21d0822ff ("ixgbe: add support for geneve Rx offload")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.
In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.
With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.
For now, avoid this optimization until it can be properly re-added in
net-next.
Fixes: fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
