This device is pad (buttons) only, there is no stylus or touch. Up to
five remotes can pair with the device's associated USB dongle.
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Prior to this commit, numbered button bit setting was done separately
for each device type in wacom_setup_pad_capabilities(). Here we add a
numbered_buttons property to the wacom_features struct and extract the
repeated bit setting code to a new function:
wacom_settup_numbered_buttons().
Signed-off-by: Aaron Skomra <aaron.skomra@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Enable ELAN0100 touchpad driver, found on a Asus X205TA laptop, to
gai 2,3 fingers tap and 2 fingers scroll.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Reviewed-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Looks like 0x8882 needs the same quirk than 0x8883.
Given that both devices claim they are "TPV OpticalTouchScreen" rename
the 0x8883 to add its PID in the #define.
Reported-by: Blaine Lee <blaine.j.lee@medtronic.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It was reported that after 10-20 reboots, a usb keyboard plugged
into a docking station would not work unless it was replugged in.
Using usbmon, it turns out the interrupt URBs were streaming with
callback errors of -71 for some reason. The hid-core.c::hid_io_error was
supposed to retry and then reset, but the reset wasn't really happening.
The check for HID_NO_BANDWIDTH was inverted. Fix was simple.
Tested by reporter and locally by me by unplugging a keyboard halfway until I
could recreate a stream of errors but no disconnect.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Enabling irq wake could potentially fail and calling disable_irq_wake
after a failed call to enable_irq_wake could result in an unbalanced irq
warning. This patch warns if enable_irq_wake fails and avoids other
potential issues caused by calling disable_irq_wake on resume after
enable_irq_wake failed during suspend.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The current generation of "Intuos" tablets (i.e. INTUOSHT) report touch
width and height data just like the "Intuos Pro" do. This commit changes
the code to allow these tablets to use the appropriate codepath instead
of the one intended for Intuos5/Bamboo.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This gamepad advertise 5 absolute axis while 4 are actually used.
The second Z axis shows some garbage, so it has to be ignored by HID.
The first Z axis and the Rz one are actually Rx and Ry. Remap them.
We could also just remap and ignore the axis in .input_mapping(). I
went ahead with .report_fixup() first, so here it is.
Reported-by: Orivej Desh <orivej@gmx.fr>
Tested-by: Orivej Desh <orivej@gmx.fr>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Don't relay a middle button press to userspace until release, and then
only if there was no scroll events inbetween. This is closer to what
Xorg's wheel emulation does, and avoids spurious middle-click pastes.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Unlike other IRQ functions, 'wacom_pl_irq' uses the second element of
the 'tool' array to store information about its single pen. This makes
the function more difficult to understand (since it doesn't follow the
general pattern of other IRQ functions) and prevents the possibility of
refactoring how pen state is stored.
This patch rewrites 'wacom_pl_irq' to follow the usual IRQ conventions,
including storing tool type in 'tool[0]' and implicitly tracking prox
with the 'id[0]' variable.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
- fix for bounds limit calculation in uclogic driver, by Dan Carpenter
- fix for use-after-free during device removal, by Krzysztof Kozlowski
- fix for userspace regression (that became apparent only with shiny
new libinput, so it's not that bad, but I still consider it 4.2
material), in wacom driver, by Jason Gerecke
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: Report correct device resolution when using the wireless adapater
HID: hid-input: Fix accessing freed memory during device disconnect
HID: uclogic: fix limit in uclogic_tablet_enable()
The 'wacom_wireless_work' function does not recalculate the tablet's
resolution, causing the value contained in the 'features' struct to
always be reported to userspace. This value is valid only for the pen
interface, meaning that the value will be incorrect for the touchpad (if
present). This in particular causes problems for libinput which relies
on the reported resolution being correct.
This patch adds the necessary calls to recalculate the resolution for
each interface. This requires a little bit of code shuffling since both
the 'wacom_set_default_phy' and 'wacom_calculate_res' are declared below
their new first point of use in 'wacom_wireless_work'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As an extension of aef3156d7, there is no sense in repeatedly calling the
'wacom_set_report' and 'wacom_get_report' functions if they return an
error. Getting an error from them implies that the device is out to lunch:
either a hard error code was returned or repeated attempts at recovering
from a "soft" error all failed. In either case, doing even more retries is
not likely to resolve whatever is wrong.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As an extension of aef3156d7, there is no sense in repeatedly calling the
'wacom_set_report' and 'wacom_get_report' functions if they return an
error. Getting an error from them implies that the device is out to lunch:
either a hard error code was returned or repeated attempts at recovering
from a "soft" error all failed. In either case, doing even more retries is
not likely to resolve whatever is wrong.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
During unbinding the driver was dereferencing a pointer to memory
already freed by power_supply_unregister().
Driver was freeing its internal description of battery through pointers
stored in power_supply structure. However, because the core owns the
power supply instance, after calling power_supply_unregister() this
memory is freed and the driver cannot access these members.
Fix this by storing the pointer to internal description of battery in a
local variable before calling power_supply_unregister(), so the pointer
remains valid.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Fixes: 297d716f62 ("power_supply: Change ownership from driver to core")
Cc: <stable@vger.kernel.org>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
WACOM_QUIRK_NO_INPUT is a signal to the driver that input devices
should not be created for a particular device. This quirk was used by
the wireless receiver to prevent any devices from being created during
the initial probe (defering it instead until we got a tablet connection
event in 'wacom_wireless_work').
This quirk is not necessary now that a device_type is associated with each
device. Any input device allocated by 'wacom_allocate_inputs' which is
not necessary for a particular device is freed in 'wacom_register_inputs'.
In particular, none of the wireless receivers devices have the pen, pad,
or touch device types set so the same effect is achieved without the need
to be explicit.
We now return early in wacom_retrieve_hid_descriptor for wireless devices
(to prevent the device_type from being overridden) but since we ignore the
HID descriptor for the wireless reciever anyway, this is not an issue.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The monitor interface on the wireless receiver is more logically expressed
as a type of device instead of a quirk.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commit 01c846f introduced the 'wacom_compute_pktlen' function which
automatically determines the correct value for an interface's pkglen
by scanning the HID descriptor. This function returns the correct
value for the wireless receiver's touch interface, removing the need
for us to set it manually here.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This commit removes the cap on the DualShock 4 controller reporting rate when
connected using Bluetooth. The previous value of '0xB0' capped the rate to only
20.83 Hz which many userspace utilities mistook as a sign of a bad signal.
Since a 'B' and an '8' can look similar it's possible that someone mistook the
one for another. The new value of '0x80' enables the full 1000 Hz peak
reporting rate that the controller is capable of.
Frank adds: "Back when the original code was written the purpose of that value
was unknown and 0xB0 seemed to work so that's what ended up being used. Now
that we know what it actually does and that 0x80 is a better choice I support
this patch."
[jkosina@suse.com: update changelog]
Signed-off-by: Rostislav Pehlivanov <atomnuker@gmail.com>
Acked-by: Frank Praznik <frank.praznik@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Pull input fixes from Dmitry Torokhov:
"The main change is support for keyboards and touchpads found in 2015
editions of Macbooks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: zforce - don't overwrite the stack"
Input: bcm5974 - add support for the 2015 Macbook Pro
HID: apple: Add support for the 2015 Macbook Pro
Input: bcm5974 - prepare for a new trackpad generation
Input: synaptics - dump ext10 capabilities as well
Acer Aspire Switch 12 keyboard Chicony's controller reports too big usage
index on the 1st interface. The patch fixes the report. The work based on
solution from drivers/hid/hid-holtek-mouse.c
Bug report: https://bugzilla.kernel.org/show_bug.cgi?id=101721
Signed-off-by: Nicholas Kudriavtsev <nkudriavtsev@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Since this wheel is now available, and the USBID is listed on their website,
this patch adds it to allow the hid-lg4ff force feedback driver to find it.
I do not have this wheel to test with, but this should at least get it working
in emulation mode.
Note: There is probably more work required for adjust HID descriptor and handle
switching between emulation and native modes.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The limit should be ARRAY_SIZE(params) (5 elements) here instead of
sizeof(params) (20 bytes).
Fixes: 08177f40bd ('HID: uclogic: merge hid-huion driver in hid-uclogic')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
This patch adds keyboard support for MacbookPro12,1 as WELLSPRING9
(0x0272, 0x0273, 0x0274). The touchpad is handled in a separate
bcm5974 patch, as usual.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some device present proprietary collections with a usage min of 0x00 and
a usage max of 0xffff. hid-core currently reject them while most of the
time this is harmless.
Let's ignore the exceeding usages, and hope for the best.
Reported-by: Simon Wörner <mail@simon-woerner.de>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When connected via Bluetooth the sixaxis periodically sends reports with an ID
of 1, the second byte 0xff and the rest zeroed. These reports are not related
to the controller state and must be dropped to avoid generating false input
events.
Link: http://www.spinics.net/lists/linux-bluetooth/msg63028.html
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Adding support for the Microsoft Surface 3 (non-pro) Type Cover.
The existing definitions and quirks are actually for the Surface
Pro 3 type covers. I've renamed the old constants to reflect that
they belong to the Surface Pro 3, and added a new constant and
matching code for the Surface 3.
Signed-off-by: Stephen Just <stephenjust@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The HID_DG_WIDTH and HID_DG_HEIGHT usages report with width and height of
contacts. From this information, a crude determination of orientation is
also possible. This patch reports all three to userspace if a device
reports this usage.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The reports sent from some touch devices (e.g. the Cintiq 24HDT) contain
junk data in the contact slots which follow the final "valid" contact.
To avoid forwarding it to usrspace, we store the reported contact count
during the pre-process phase and then only process that many contacts.
If a device sends its contacts across multiple reports (what Microsoft
refers to as "hybrid" mode) then the contact count will be zero for
reports other than the first.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
In some cases, we need access to information before it becomes available
to the 'event' handler. In particular, for some devices we cannot properly
process the finger data without first knowing the "contact count" at the
very end of the report (e.g. the Cintiq 24HDT touch screen, when forced
through the GENERIC codepath).
Since the HID subsystem doesn't provide a way to take action before 'event'
is called, we take a cue from hid-multitouch.c and add a pre-process step
within the 'report' handler that performs the same function.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
ELAN0600 seems to work just fine in mouse emulation mode through i2c-hid,
but to have full raw touch support we need to register it in elan_i2c.ko
Reported-and-tested-by: Alessio Treglia <alessio@debian.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A firmware bug in some touchpads causes the F01 interrupt enable register
to be cleared on reset. This register controls which RMI functions generate
interrupts and when it is cleared, the touchpad stops reporting all data.
This patch looks for the cleared F01 control register and writes the
correct value based on interrupt mask computed while scanning the PDT.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=91102
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Allocated input devices should not use the 'pen_name' by default since
we do not know at that point in time if that is an appropriate choice
of name. Instead, use the (tool-agnostic) name that is stored in the
device's 'wacom_features' structure. This also has the nice side-effect
of requring us to be explicit about the naming of the pen device, as
we already are for touch and pad devices.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The 'wacom_allocate_inputs' function tries to allocate three input devices: one
each for the pen, touch, and pad. The pointers that are returned by the
'wacom_allocate_input' calls are temporarily stored to local variables where
they are checked to ensure they're non-null before storing them in the
'wacom_wac' structure. If an allocation fails, the 'wacom_free_inputs'
function is called to reclaim the memory. Unfortunately, 'wacom_free_inputs' is
called prior to the pointers being copied, so it is not actually able to free
anything.
This patch has the calls to 'wacom_allocate_input' store the pointer directly
in the 'wacom_wac' structure where they can be freed. Also, it replaces the
call to 'wacom_free_inputs' with the (more general) 'wacom_clean_inputs' and
removes the no-longer-used function.
[jkosina@suse.com: modify to resolve conflict with 67e123f ("Delete
unnecessary checks")]
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
There is a conflict between 67e123f ("Delete unnecessary checks") sitting
in for-4.3/upstream and memory allocation failure handling from Jason Gerecke.
Pull this so that conflict could be resolved.
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Change all occurrences of be16 to le16 in cp2112_xfer(),
because SMBUS words are little endian, not big endian.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When doing an I2C_SMBUS_BYTE write (one byte write, no address),
the data to be written is in "command" not "data->byte".
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
As mentioned in the comment in the code, both the pen and touch data
come from the interface tagged as BAMBOO_PAD. The driver re-routes the
events for the Pen to the generic HID interface and keeps the ones for
the touch through this current interface.
Clearing the WACOM_DEVICETYPE_PEN bit removes the extra unused interface
added in 2a6cdbd ("HID: wacom: Introduce new 'touch_input' device") and
makes the Bamboo PAD to behave like in 4.1.
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
When a device is reset the values of control registers will be reset to
the defaults. This patch reapplies the control register values set for F11
by the driver.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
We need to emit EV_SYN/SYN_REPORT between key press and release, otherwise
userspace is allowed to "swallow" the event.
[jkosina@suse.com: Dmitry says that he's observing this behavior with
Plantronics headset]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
cp2112_i2c_xfer() only supports a single i2c_msg. More than
one message at a time just returns EIO. This breaks certain
important cases. For example, the at24 eeprom driver generates
paired write and read messages (for eeprom address and data).
Since the device doesn't support i2c repeated starts in general,
but does support a single write-repeated-start-read pair
(since hardware rev 1), we recognize the latter case and
implement only that.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The input_free_device() function tests whether its argument is NULL and
then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Some touchpads are configured with firmware which continues to scan for
fingers at a minimal scan rate even after receiving the HID power sleep
command. This allows a finger touching the touchpad to genrate a wake
event. This patch ensures that scanning is disabled if the touchpad is
not a wake source and ensures scanning is enabled on resume.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
cp2112_i2c_xfer() only reads up to 61 bytes, returning EIO on longers reads.
The fix is to wrap a loop around cp2112_read() to pick up all the returned
data.
Signed-off-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
i2c-hid takes care of requesting and handling IRQs for HID devices
which in turns might expect them to be always active when working
in normal conditions. Hence, disabling IRQs before calling the suspend
callbacks can potentially cause problems since device drivers might
try to perform operations needing them.
Fix this by disabling IRQs only after the suspend callbacks had been
executed.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Current implementation of cp2112_raw_event() only accepts one data report at a
time. If last received data report is not fully handled yet, a new incoming
data report will overwrite it. In such case we don't guaranteed to propagate
the correct incoming data.
The trivial fix implemented here forces a single report at a time by requesting
in cp2112_read() no more than 61 byte of data, which is the payload size of a
single data report.
Cc: stable@vger.kernel.org
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Tested-by: Ellen Wang <ellen@cumulusnetworks.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Commit 862cf55 ("HID: wacom: Introduce a new WACOM_DEVICETYPE_PAD device_type")
neglected to set the WACOM_DEVICETYPE_PAD flag for older two-finger Bamboo
Touch tablets. Not only does this result in the pad device not appearing when
such a tablet is plugged in, but also causes a segfault when 'wacom_bpt_touch'
tries to send pad events. This patch adds the flag to resolve these issues.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
During open() it is unnecessary to wait for the device to flush
stale inputs if the device is polled while closed due to a quirk
or opening fails.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Fields like HID_DG_CONTACTCOUNT are outside of the physical collection,
but within the application collection and report ID. Make sure to catch
those fields that are not part of the mt_report_id and return 0 so they
can be processed with the pen. Otherwise, the wrong HID_DG_CONTACTCOUNT
will be applied to cc_index and result in dereferencing a null pointer in
mt_touch_report.
Signed-off-by: Brent Adam <brentadam@smarttech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The functions backlight_device_unregister(), lcd_device_unregister() and
rc_unregister_device() test whether their argument is NULL and then
return immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
The newer firmware on MS Surface 2 tablets causes the type and touch cover keyboards to timeout when waiting for reports.
The quirk HID_QUIRK_NO_INIT_REPORTS allows them to function normally.
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We can't pass a NULL to input_unregister_device().
Fixes: 2a6cdbdd4c ('HID: wacom: Introduce new 'touch_input' device')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adding support for the Microsoft Surface Pro Power Cover.
Signed-off-by: Raimund Roth <raimundmroth@gmail.gom>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Instead of having a single 'input_dev' device that will take either pen
or touch data depending on the type of the device, create seperate devices
devices for each. By splitting things like this, we can support devices
(e.g. the I2C "AES" sensors in some newer tablet PCs) that send both pen
and touch reports from a single endpoint.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This splits the 'wacom_setup_pentouch_input_capabilites' function into
pieces dedicated to doing setup for just the pen interface and just
the touch interface. This makes it easier to focus on the relevant
piece when making changes.
This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Historically, both the touch and pad tools would have shared the
'BTN_TOOL_FINGER' type. Any time you needed to distinguish the two, you
had to use some other bit of knowledge (e.g. that the pad was on the same
interface as the pen, and thus 'touch_max' would be zero).
To make these checks more readable, we introduce WACOM_DEVICETYPE_PAD.
Although we still have to rely on other bits of knowledge to set this
bit on the right interface (since it cannot be detected from the HID
descriptor), it can be done just once inside 'wacom_setup_device_quirks'.
This patch introduces no functional changes.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The USB devices that this driver has historically supported segregate the
pen and touch portions of the tablet. Oftentimes the segregation would be
done at the interface level, though on occasion (e.g. Cintiq 24HDT) the
tablet would combine two totally independent USB devices behind an internal
USB hub. Because pen and touch never shared the same interface, it made
sense for the 'device_type' to store a single value: "pen" or "touch".
Recently, however, some I2C devices have been created which combine the
two. A first step to accomodating this is to expand 'device_type' so that
it can represent two (or potentially more) types simultaneously. To do
this, we treat it as a bitfield and set/check individual bits rather
than using the '=' and '==' operators.
This should not result in any functional change since no supported devices
(that I'm aware of, at least) have HID descriptors that indicate both
pen and touch reports on a single interface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A little bit of cleanup work for 'wacom_update_name' to make it easier on
the eyes. Creates a temporary 'name' variable on which we'll perform our
edits. Once the name is in its final form, it will be copied (with
appropriate suffix) to 'wacom_wac->name' and 'wacom_wac->pad_name'.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Physical buttons do not use F30 to report their state and in some cases the
data reported in F30 is incorrect and inconsistent with what is reported by
the HID descriptor. When physical buttons are present, ignore F30 and let
hid-input report buttons based on what is defined in the HID descriptor.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update Kconfig with enhanced help text for hid-plantronics driver.
Update hid-plantronics.c to identify device type and correctly map
either the vendor unique or consumer control volume up/down usages
to KEY_VOLUMEUP and KEY_VOLUMEDOWN events. Unmapped usages are ignored
to prevent core mapping of unknown usages to random mouse events.
Tested on ChromeBox/ChromeBook with various Plantronics devices.
Signed-off-by: Terry Junge <terry.junge@plantronics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix the report descriptor so that the buttons and trigger are correctly reported.
The format of the input report is described here:
https://github.com/nitsch/moveonpc/wiki/Input-report
The Accelerometers and Gyros (1st frame only) are also reported as axis, but
the Magnetometers are NOT as 'fixing' their byte order would break user-space
drivers such as PSMoveAPI.
It is hoped to resolve this at a future time.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The LED and Rumble control only function via BT if the full output report
is sent. The large report still functions via USB.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support for the battery charge level and state to be read via BT.
This is not support via USB as there is no know way to get the device
sending 'input' reports over USB.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Split quirk for PS Move Controller as it has to be treated differently
when connected via BT.
Signed-off-by: Simon Wood <simon@mungewell.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID device does not need to know about the ACPI device associated with
the underlying i2c device. Setting the ACPI companion field in the HID device
also has the side effect of causing HID to be set as wake capable, since
acpi_bind_one uses's the companion ACPI device's wakeup flags to set the
device as wake capable. Which results in power/wakeup files in sysfs for
the HID device which do not do anything.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Tested-by: Benson Leung <bleung@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Removes Vernier Software & Technology devices from the ldusb
driver and the hid_ignore_list table of the usbhid driver in the
Linux tree. These devices will now be supported via the hidraw
driver.
A user space driver for these devices will be found in the
Go! Software Development Kit from Vernier at
http://www.vernier.com/downloads/software-development-kits/go-sdk/.
These devices are also be supported by the LabQuest2 standalone
interface shown at http://www.vernier.com/products/interfaces/labq2/
and the LoggerPro for Linux software shown at
http://www.vernier.com/downloads/logger-pro-linux/.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech M560 is a wireless mouse designed for windows 8 which uses
the unifying receiver.
Compared to a standard one, some buttons (the middle one and the
two ones placed on the side) are bound to a key combination
instead of a generating classic "mouse" button events.
The device shows up as a mouse and keyboard combination: when the middle
button is pressed it sends a key (as keyboard) combination, the same
happens for the two side button. The left/right/wheel work as expected
from a mouse. To complicate things further, the middle button sends
different keys combinations between odd and even presses.
In the "even" press it also sends a left click. But the worst thing
is that no event is generated when the middle button is released.
It is possible to re-configure the mouse sending a command (see function
m560_send_config_command()). After this command the mouse sends some
useful data when the buttons are pressed and/or released.
[jkosina@suse.cz: fix build breakage due to leftover from previous
patch version]
Signed-off-by: Goffredo Baroncelli <kreijack@inwind.it>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rename the function extract() to hid_field_extract(), make it external linkage
to allow the use from other modules.
Suggested-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Goffredo Baroncelli <kreijack@inwind.it>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is no sysfs_group_remove() on failure path in lenovo_probe_tpkbd().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There are too many bangs in this conditional; therefore
remove them while still maintaining the same logic.
Signed-off-by: James C Boyd <jcboyd.dev@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
GCC reports a -Wlogical-not-parentheses warning here; therefore
add parentheses to shut it up and to express our intent more.
Signed-off-by: James C Boyd <jcboyd.dev@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Most of the entries are aligned with TABs, fix those which are not.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I received a report from an user of following mouse which needs this quirk:
usb 1-1.6: USB disconnect, device number 58
usb 1-1.6: new low speed USB device number 59 using ehci_hcd
usb 1-1.6: New USB device found, idVendor=04f2, idProduct=1053
usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1.6: Product: USB Optical Mouse
usb 1-1.6: Manufacturer: PixArt
usb 1-1.6: configuration #1 chosen from 1 choice
input: PixArt USB Optical Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input5887
generic-usb 0003:04F2:1053.16FE: input,hidraw2: USB HID v1.11 Mouse [PixArt USB Optical Mouse] on usb-0000:00:1a.0-1.6/input0
The quirk was tested by the reporter and it fixed the frequent disconnections etc.
[jkosina@suse.cz: reorder the position in hid-ids.h]
Signed-off-by: Herton R. Krzesinski <herton@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull HID fixes from Jiri Kosina:
"Bugfixes for HID subsystem that should go in 4.1. Important
highlights:
- the patch that extended support for HID++ protocol for TK820
touchpad turns out to be causing regressions due to firmware
issues; patch reverting back to basic support from Benjamin
Tissoires
- Wacom driver can oops for devices that report non-touch data on
touch interfaces. Fix from Ping Cheng
- gpiolib is not mandatory for i2c-hid, so the driver shouldn't fail
if gpiolib is not enabled. Fix from Mika Westerberg"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: wacom: fix an Oops caused by wacom_wac_finger_count_touches
HID: usbhid: Add HID_QUIRK_NOGET for Aten DVI KVM switch
HID: hid-sensor-hub: Fix debug lock warning
Revert "HID: logitech-hidpp: support combo keyboard touchpad TK820"
HID: i2c-hid: Do not fail probing if gpiolib is not enabled
Hardware may not respond to a request for the HID_DG_CONTACTMAX feature and
we should be tolerant of such a failure. This is especially true when using
hid-replay where the hardware doesn't exist, but also for devices attached
to a flaky bus. This patch increases the number of allowable retries to
match other calls to 'wacom_get_report' and also provides a fallback which
forces 'touch_max = 16' (enough for any Wacom device seen so far).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Retrying on -EPIPE makes very little sense since this typically indicates
a problem that will not just disappear on its own. For instance, the USB
documentation states that it will be sent if the endpoint is stalled or
the device has disconnected. Instead, we should retry if -EAGAIN is
received since this indicates a temporary error condition such as a busy
bus.
In addition to adjusting the conditions we retry under, we also log an
error on failure so that we can be aware of what's going on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We assumed all touch interfaces report touch data. But, Bamboo
and Intuos non-touch devices report express keys on touch
interface. We need to check touch_max before counting touches.
Reported-by: Tasos Sahanidis <tasos@tasossah.com>
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These defines are used like this:
if (test_bit(I2C_HID_STARTED, &ihid->flags))
The intent was to use bits 0, 1, and 2 but because of the extra shifts
we're using bits 1, 2, and 4. It's harmless becuase it's done
consistently but it's not the intent and static checkers will complain.
Fixes: 4a200c3b9a ('HID: i2c-hid: introduce HID over i2c specification implementation')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These defines are used like this:
if (!(test_bit(RMI_STARTED, &hdata->flags)))
So the intent was to use bits 0, 1 and 2 but because of the extra BIT()
shifts we're actually using 1, 2 and 4. It's harmless because it's done
consistently but static checkers will complain.
Fixes: 9fb6bf02e3 ('HID: rmi: introduce RMI driver for Synaptics touchpads')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Like other KVM switches, the Aten DVI KVM switch needs a quirk to avoid spewing
errors:
[791759.606542] usb 1-5.4: input irq status -75 received
[791759.614537] usb 1-5.4: input irq status -75 received
[791759.622542] usb 1-5.4: input irq status -75 received
Add it.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Once there were kernel drivers for some of the phidgets devices, and for
those kernel drivers to work the hid system needed exceptions. Now the
kernel drivers are long gone in favour of the user-space drivers.
The user-space drivers support many more phidget devices and uses libusb.
The udev rules set up permissions so that the kernel hid driver can be
unbound from libusb, as it does for many devices not in hid_ignore_list.
http://www.phidgets.com/docs/OS_-_Linux
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When CONFIG_DEBUG_LOCK_ALLOC is defined, mutex magic is compared and
warned for (l->magic != l), here l is the address of mutex pointer.
In hid-sensor-hub as part of hsdev creation, a per hsdev mutex is
initialized during MFD cell creation. This hsdev, which contains, mutex
is part of platform data for the a cell. But platform_data is copied
in platform_device_add_data() in platform.c. This copy will copy the
whole hsdev structure including mutex. But once copied the magic
will no longer match. So when client driver call
sensor_hub_input_attr_get_raw_value, this will trigger mutex warning.
So to avoid this allocate mutex dynamically. This will be same even
after copy.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Only one of LG_FF flags can be set for a given device.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow the driver to continue without sysfs interface. Instead of bailing out
allow the driver to continue in a degraded mode.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Constify those members of lg4ff_device_entry struct whose value is not
supposed to change.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Store pointer to the output HID report struct in the device entry struct.
This eliminates the need to look the HID report struct up every time it is needed.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Protect concurrent access to output HID report with a spinlock. The HID report
structure used to submit commands to wheels is shared amongst all functions that
need to do so and some of these functions can be executed in parallel.
Additionally, lg4ff_play() can be called from interrupt context by ff-memless
module. Locking is necessary to prevent sending bogus data to the wheels.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stop the hid device from lg4ff. Originally hid-lg was responsible for
stopping of the device.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make lg4ff_wheel_data a separate structure stored within lg4ff_device_entry.
Adjust the initialization process accordingly.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Check return values from lg[N]ff_init(). hid-lg did not check return values from
the lg[N]_init() functions, possibly trying to work with a device whose
initialization has failed.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Update a warning message for a case where device is incorrectly flagged to be
handled by hid-lg4ff in hid-lg. The original warning message was highly
misleading. This warning can be triggered only if a device is flagged to be
handled by hid-lg4ff in hid-lg but hid-lg4ff lacks support for such device.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove unused variable from the "lg4ff_device_entry" struct. This is a leftover
from times where hid_get|set_drvdata() was not available to hid-lg4ff so it had
to keep track of the devices it managed by itself.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Replace DEVICE_ATTR_RW with DEVICE_ATTR to have all internal functions prefixed
with "lg4ff_". All internal functions should be prefixed with just "lg4ff_".
Usage of DEVICE_ATTR_RW breaks this scheme because it expects the functions'
names to match the name of the respective sysfs entry.
This partially reverts "2f1cec3250e38609bf9252db52dbbe61603c04a7"
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove "hid_" prefix from some functions' names. All internal functions
of hid-lg4ff should be prefixed with just "lg4ff_"
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove double underscore prefix from numeric types. This code will never be used
outside the kernel so the prefixes are unnecessary.
Signed-off-by: Michal Malý <madcatxster@devoid-pointer.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This reverts commit 3a61e97563.
The Logitech TK820 seems to be affected by a firmware bug which
delays the sending of the keys (pressed, or released, which triggers
a key-repeat) while holding fingers on the touch sensor.
This behavior can be observed while using the mouse emulation mode
if the user moves the finger while typing (highly improbable though).
Holding the finger still while in the mouse emulation mode does
not trigger the key repeat problem.
So better keep things in their previous state to not have to
explain users that the new key-repeat bug they see is a "feature".
Furthermore, I noticed that I disabled the media keys whith
this patch. Sorry, my bad.
I think it is best to revert the patch, in all the current
versions it has been shipped.
Cc: <stable@vger.kernel.org> # v3.19 and above
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Correct a spelling mistake in the Sixaxis HID descriptor comment.
Add an explanation as to why the Sixaxis has so many analog axes and why
some of them are seen as multi-touch axes.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Directly set the initial LED states in the device state struct instead
of copying them from a temporary array.
This allows for the removal of a redundant "x = x" copy loop in
sony_set_leds() that was taking place any time an LED was updated.
It also allows for the simplifying of the parameters in functions dealing
with LED initialization and updates since only a pointer to the sony_sc
struct is needed now.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Rearrange Sony controller devices into alphabetical order in the hardware
device list.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a fixed-up HID descriptor for the Sony motion controller and enable
controls for the LED light as well as force-feedback.
The LED is multi-colored (red, green, blue).
The motion controller has a single rumble motor so the higher of the left
and right values is used to set the speed.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Adds the PID for the Sony motion controller to the hardware ID list.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
sony_allocate_output_report() was being called before sony_set_device_id()
which meant that an unallocated ida value was was freed if the output
report allocation failed and the probe function jumped to err_stop.
Do the device ID allocation before the output report allocation to avoid
freeing an unallocated value in case of a failure.
Signed-off-by: Frank Praznik <frank.praznik@oh.rr.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
'key' is set but never used in the first loop. So remove the set.
And indent the re-set of pm->last_key properly.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
wait_event_interruptible_timeout() expects a timeout in jiffies so the
numeric constant becomes HZ dependent - put it through msecs_to_jiffies()
to make it HZ independent.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This dock is used with the Thinkpad Helix 2 but suffers from an error
in the report descriptor where an usage max is 65535.
Add a report fixup for it and make the keyboard working.
Tested-by: Jonathan Oppenheim <lejono@gmail.com>
Tested-by: John Reid <owlman.lists@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The last patch was careful to maintain backwards-compatible behavior
by forcing device_type to BTN_TOOL_PEN (and printing a warning) if it
were still uninitialized after scanning the HID descriptor and applying
quirks. We should be more strict with HID_GENERIC devices, however,
since there is no a priori guarantee that it is a tablet or touchpad.
If the device_type is still uninitialized for a HID_GENERIC device then
we assume that it isn't something the driver can work with and so fail
the probe.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently, we assume a device_type of BTN_TOOL_PEN before scanning the
HID descriptor and then change the device_type if what we discover
proves that assumption wrong. This way of doing things makes it more
difficult to figure out if a device (particularly a HID_GENERIC device)
actually does tablet/touch input or is something completley different.
This patch leaves device_type at its initial value of 0 and then calls
'wacom_parse_hid' for every device (not just those that have touch).
As we map the usages, we can set the device_type as before. After we're
finished, we can then check if the value is still zero and do whatever
is most appropriate.
Detecting the pen can be a little tricky on most Wacom devices because
the descriptors describe opaque blobs. Fortunately, older Wacom tablets
have the HID_DG_DIGITIZER usage on the pen's application collection and
newer tablets seem to have a similar vendor-defined usage that we can
trigger on.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The naming logic currently assumes that all devices will be a pen, finger,
or pad. Though this has historically been the case, the new HID_GENERIC
catch-all may cause us to probe devices with Wacom's 056A VID which aren't
any of these types (e.g. the "Cintiq 24HDT Monitor Control"). This patch
updates the logic so that no suffix will be added to the device name if
the device type is unknown.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID generic devices share the same default name, "Wacom HID". This
causes userland programs to show same device names for different
devices, which would confuse end users with same device names for
different devices too.
This patch uses name retrieved from HID descriptor, if a meaningful
name is reported. Otherwise, affix its product ID to "Wacom HID".
Names from descriptor may contain extra whitespaces. To comfort
readers' eyes, we removed those extra whitespaces too.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The raphnet.net 4nes4snes and 2nes2snes multi-joystick adapters use a single
HID report descriptor with one report ID per controller. This has the effect
that the inputs of otherwise independent game controllers get packed in one
large joystick device.
With this patch each controller gets its own /dev/input/jsX device, which is
more natural and less confusing than having all inputs going to the same place.
Signed-off-by: Raphael Assenat <raph@raphnet.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Using GPIOs and gpiolib is optional. If the kernel is compiled without GPIO
support the driver should not fail if it finds the interrupt using normal
methods.
However, commit a485923efb ("HID: i2c-hid: Add support for ACPI GPIO
interrupts") did not take into account that acpi_dev_add_driver_gpios()
returns -ENXIO when !CONFIG_GPIOLIB.
Fix this by checking the return value against -ENXIO and 0 and only in that
case fail the probe.
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Set flags INPUT_PROP_POINTER and INPUT_PROP_POINTING_STICK for the trackpoint
integrated in Lenovo USB and Bluetooth keyboards. Libinput checks these flags
to enable features such as middle-button-scrolling by default.
Signed-off-by: Andreas Fleig <andreasfleig@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To determine if a touch is present in the single-touch case, we can
simply check if the BTN_TOUCH key is active or not. This will work for
both HID_GENERIC and other device types.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We use generic hid_report_len() to get individual packet length now.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
That is where they belong...
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It makes probe routine easy to follow.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull input subsystem updates from Dmitry Torokhov:
"You will get the following new drivers:
- Qualcomm PM8941 power key drver
- ChipOne icn8318 touchscreen controller driver
- Broadcom iProc touchscreen and keypad drivers
- Semtech SX8654 I2C touchscreen controller driver
ALPS driver now supports newer SS4 devices; Elantech got a fix that
should make it work on some ASUS laptops; and a slew of other
enhancements and random fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: alps - non interleaved V2 dualpoint has separate stick button bits
Input: alps - fix touchpad buttons getting stuck when used with trackpoint
Input: atkbd - document "no new force-release quirks" policy
Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
Input: ALPS - V7 devices can report 5-finger taps
Input: ALPS - add support for SS4 touchpad devices
Input: ALPS - refactor alps_set_abs_params_mt()
Input: elantech - fix absolute mode setting on some ASUS laptops
Input: atmel_mxt_ts - split out touchpad initialisation logic
Input: atmel_mxt_ts - implement support for T100 touch object
Input: cros_ec_keyb - fix clearing keyboard state on wakeup
Input: gscps2 - drop pci_ids dependency
Input: synaptics - allocate 3 slots to keep stability in image sensors
Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
Input: MT - make slot assignment work for overcovered solutions
mfd: tc3589x: enforce device-tree only mode
Input: tc3589x - localize platform data
Input: tsc2007 - Convert msecs to jiffies only once
Input: edt-ft5x06 - remove EV_SYN event report
Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
...
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
* new API for safe access of power supply function attrs
* devres support for power supply (un)registration
* new drivers / chips
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
* twl4030-madc-battery: convert to iio consumer
* misc fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WbZu
-----END PGP SIGNATURE-----
Merge tag 'for-v4.1' of git://git.infradead.org/battery-2.6
Pull power supply and reset changes from Sebastian Reichel:
- new API for safe access of power supply function attrs
- devres support for power supply (un)registration
- new drivers / chips:
- generic syscon based poweroff driver
- iio & charger driver for da9150
- fuel gauge driver for axp288
- bq27x00: add support for bq27510
- bq2415x: add support for bq24157s
- twl4030-madc-battery: convert to iio consumer
- misc fixes
* tag 'for-v4.1' of git://git.infradead.org/battery-2.6: (66 commits)
power: twl4030_madc_battery: Add missing MODULE_ALIAS
power: twl4030-madc-battery: Convert to iio consumer.
dt: power: Add docs for generic SYSCON poweroff driver.
power: reset: Add generic SYSCON register mapped poweroff.
power: max17042_battery: add missed blank
power: max17042_battery: Use reg type instead of chip type
power/reset: at91: big endian fixes for atsama5d3x
power_supply: charger-manager: Fix dereferencing of ERR_PTR
HID: input: Fix NULL pointer dereference when power_supply_register fails
power: constify of_device_id array
power/reset/rmobile-reset.c: Fix !HAS_IOMEM build
power_supply: 88pm860x_charger: Fix possible NULL pointer dereference and use of initialized variable
arm: mach-pxa: Decrement the power supply's device reference counter
mfd: ab8500: Decrement the power supply's device reference counter
power_supply: bq2415x_charger: Decrement the power supply's device reference counter
power_supply: 88pm860x_charger: Decrement the power supply's device reference counter
x86/olpc/xo15/sci: Use newly added power_supply_put API
x86/olpc/xo1/sci: Use newly added power_supply_put API
power_supply: charger-manager: Decrement the power supply's device reference counter
power_supply: Increment power supply use counter when obtaining references
...
HID Sensor Spec defines two usage ids for custom sensors
HID_USAGE_SENSOR_TYPE_OTHER_CUSTOM (0x09, 0xE1)
HID_USAGE_SENSOR_TYPE_OTHER_GENERIC(0x09, 0xE2)
In addition the standard also defines usage ids for custom fields.
The purpose of these sensors is to extend the functionality or provide a way to
obfuscate the data being communicated by a sensor. Without knowing the mapping
between the data and its encapsulated form, it is difficult for an driver to
determine what data is being communicated by the sensor. This allows some
differentiating use cases, where vendor can provide applications. Since these
can't be represented by standard sensor interfaces like IIO, we present these
as fields with
- type (input/output)
- units
- min/max
- get/set value
In addition an dev interface to transfer report events. Details about this
interface is described in /Documentation/hid/hid-sensor.txt. Manufacturers
should not use these ids for any standard sensors, otherwise the the
product/vendor id can be added to black list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In the unlikely case of hdev vanishing while hid_debug_events_read() was
sleeping, we can't really break out of the case switch as with other cases,
as on the way out we'll try to remove ourselves from the hdev waitqueue.
Fix this by taking a shortcut exit path and avoiding cleanup that doesn't
make sense in case hdev doesn't exist any more anyway.
Reported-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Return a negative error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cintiq 13HD Touch is a new display tablet with pen and 10 finger touches.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Logitech T650 used to report 3 fingers swipes to the up as a press on the
Super key. When we switched the touchpad to the raw mode, we also disable such
firmware gesture and some users may rely on it.
Unfortunately, 3 finger swipes are still not supported in most of the Linux
environments, which means that we disabled a feature of the touchpad.
Allow users to revert the raw reporting mode and keep going with the firmware
gestures by providing a new module parameter.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The device exists with two device IDs instead of one as previously
believed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
During a stress test these mice kept dropping and reappearing
in runlevel 1 as opposed to 5.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In wacom_bpt_pen, we checked touch_down before assigning new
stylus_in_proximity value. This would cause stylus_in_proximity not updated
properly if touch is down before pen is in proximity.
[jkosina@suse.cz: fix if-else style]
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Counting number of touching fingers by wacom_wac_finger_count_touches so we
don't have to count them inside individual routines.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The quirk was added for devices that support both pen and touch. It decides if
a device supports multiple inputs by hardcoded feature type. However, for some
devices, we do not know if they support both before accessing their HID
descriptors.
This patch relies on dynamically assigned device_type to make the decision.
Also, we make it certain that wacom_wac->shared is always created. That is, the
driver will not be loaded if it fails to create wacom_wac->shared.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/hid/wacom_wac.c
Need to fetch the 4.0 fixes to apply 4.1 patches based on top
of those.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Force-beedback core guarantees that the 'effect' pointer that's being passed
to ->upload() callback is non-NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse is also known under other IDs. It needs the quirk or will disconnect
in runlevel 1 or 3.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Do not call power_supply_powers() if power_supply_register() failed
earlier. This fixes possible NULL pointer dereference by
power_supply_powers() in such case.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVD1VGAAoJEHm+PkMAQRiG7yoH/juKOQ1zbxi5M+mleDEEJtA0
RxQSojqEMWIKrWi8PNZxjENn1OZB6XOLIXOhlyAZBrmgsjO34p1DyXlZMznr/R8W
kQ2Xxs061hRtB3OuruMIqOApUrjuqsaCwgbgUS1qWmqZcoyZN4oELyZMP6OOlqv5
UUBZm8MfyXGyxrCcg39mjct3VEOhiuEcvL6SUxOC380CdSVAnyqHFPcz0JVqMUn9
9RUBs0T9cMdhb0mZ2bfXzt6AKArj63G2nXOum+VzFcvspSm2U+MPIDCuoE+ZbTPS
jqIAgG0rj1ezRyb5oeJrvlU0Yy3u/cXoMPs9+kORvpladooYNLti8ovh6qllm0I=
=d/ye
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc5' into next
Merge with the latest upstream to synchronize Synaptics changes
and bring in new infrastructure pieces.
Conflicts:
drivers/input/mouse/synaptics.c
486b908 (HID: wacom: do not send pen events before touch is up/forced out)
introduces a kernel oops when plugging a tablet without touch.
wacom->shared is null for these devices so this leads to a null pointer
exception.
Change the condition to make it clear that what we need is wacom->shared
not NULL.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If noone listens to the input device when a tool comes in proximity,
the tablet does not send the in-prox event when a client becomes available.
That means that no events will be sent until the tool is taken out of
proximity.
In this situation, ask for the report WACOM_REPORT_INTUOSREAD which will
read the corresponding feature and generate an in-prox event.
To make some generation of hardware working, we need to unset the
quirk NO_GET set by hid-core because the interfaces are seen as "boot
mouse".
We don't schedule this read in a worker while we are in an IO interrupt.
We know that usbhid will do it asynchronously. If this is triggered by
uhid, then this is obviously a client side bug :)
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since I can't change the type of hid_set_field argument 3, using __force __s32 to remove
this warning.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
For defining enumeration values like report or power status events, the
enumeration usage ids are enclosed in a logical collection. In this case we
need to match logical usage id for pending read on this usage id. For example,
in the below field, when read is requested for 0319, the report will
contain one of the status usages like 850, 851 etc. In this case the raw
event will not match 0319. So when logical collection matches, then wake
up the pending thread.
Physical(Sensor.OtherCustom)
Logical(Sensor.0319)
Application(Sensor.Sensor)
Usage(6)
Sensor.0850
Sensor.0851
Sensor.0852
Sensor.0853
Sensor.0854
Sensor.0855
Logical Minimum(1)
Logical Maximum(5)
Report Size(8)
Report Count(1)
Report Offset(24)
Flags( Array Absolute )
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This driver didn't exist until before v3.19.
Why would suddenly everybody want to build it?
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The PID driver (usbhid/hid-pidff.c) does not set the effect ID when
uploading an effect. The result is that the initial upload works but
subsequent uploads to modify effect parameters are all directed at the
last-created effect.
The targeted effect ID must be passed back to the device when effect
parameters are changed. This is done at the start of
"pidff_set_condition_report", "pidff_set_periodic_report" etc. based on
the value of "pidff->block_load[PID_EFFECT_
BLOCK_INDEX].value[0]".
This value is only ever set during pidff_request_effect_upload.
The result is stored in "pidff->pid_id[effect->id]" at the end of
pid_upload_effect, for later use. However, if an effect is modified and
re-sent then this identifier is not being copied back from
pidff->pid_id[effect->id] before sending the command to the device. The
fix is to do this at the start of pidff_upload_effect.
Signed-off-by: Jim Keir <jimkeir@oracledbadirect.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Many HID driver options are hidden unless EXPERT is set. While I
understand the idea of simplifying the kernel configuration for most
users, in practice I believe it adds more confusion than it helps.
One thing that worries me is that, in non-EXPERT mode, these drivers
will be either built-in or modular based on apparent magic. For
example, switching INPUT and HID from m to y will cause all these
drivers to be built into the kernel when they were previously built
as modules. Short of enabling EXPERT mode altogether, the user has no
control over that.
Generally I do not think tristate options should depend on !EXPERT.
Of these, 11 of 15 are currently in the hid subsystem.
The HID_LOGITECH option is even worse than the others. Sub-options
depend on it, and this causes menuconfig and friends to display the
option even though the user can't change its value. The help page for
HID_LOGITECH will not explain why the value can't be changed. It only
says, for example:
Depends on: INPUT [=y] && HID [=y]
and that leaves the user puzzled about why the option is forced to y.
You might argue that this is a Kconfig bug, but that doesn't make it
less annoying for the user.
Even worse is that some of the sub-options of HID_LOGITECH select
INPUT_FF_MEMLESS, which in turn gets out of control for the user. So,
if you set INPUT=y and HID=y (something most general purpose
distributions would do these days, as both modules would get loaded on
a vast majority of systems otherwise), and you want support for
force-feedback game controllers, you can't have that as a module, it
has to be built-in, regardless of how rare these devices are.
Of course, all this madness goes away once EXPERT is enabled, but then
the rest of the kernel configuration becomes more complex, which
totally voids the original point.
For this reason, I would like all HID device tristate options to be
displayed regardless of EXPERT being set or not. We can let the
default settings still depend on EXPERT, that's not intrusive.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
No need to retrieve the USB handle in input_mapping() when we already
do that in probe. It also allows to use the quirk without having to
add the product ID matching.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The linux kernel has supported the TiVo Slide remote control for some time, but
does not recognize the USB ID of the newer Slide Pro. This patch adds the
missing data structures so the newer remote will be recognized by the driver,
thereby allowing the TiVo, LiveTV, and Thumbs Up/Down buttons to be
mapped with a hwdb file.
Signed-off-by: Forest Wilkinson <web11.forest@tibit.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.
The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.
Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.
Instead let the core own the instance of struct 'power_supply'. Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.
This solves invalid memory references in following race condition
scenario:
Thread 1: charger manager
Thread 2: power supply driver, used by charger manager
THREAD 1 (charger manager) THREAD 2 (power supply driver)
========================== ==============================
psy = power_supply_get_by_name()
Driver unbind, .remove
power_supply_unregister()
Device fully removed
psy->get_property()
The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.
This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):
$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[ 55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 55.732584] pgd = d98d4000
[ 55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[ 55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 55.746210] Modules linked in:
[ 55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G W 3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[ 55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[ 55.771647] PC is at 0x0
[ 55.774182] LR is at charger_get_property+0x2f4/0x36c
[ 55.779201] pc : [<00000000>] lr : [<c034b0b4>] psr: 60000013
[ 55.779201] sp : daf55e90 ip : 00000003 fp : 00000000
[ 55.790657] r10: 00000000 r9 : c06e2878 r8 : d9b26c68
[ 55.795865] r7 : dad81610 r6 : daec7410 r5 : daf55ebc r4 : 00000000
[ 55.802367] r3 : 00000000 r2 : daf55ebc r1 : 0000002a r0 : d9b26c68
[ 55.808879] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 55.815994] Control: 10c5387d Table: 598d406a DAC: 00000015
[ 55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[ 55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[ 55.831795] 5e80: 60000013 c01459c4 0000002a c06f8ef8
[ 55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[ 55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[ 55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[ 55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[ 55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[ 55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[ 55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[ 55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[ 55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[ 55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[ 55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[ 55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[ 55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[ 55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[ 55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[ 55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[ 55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[ 55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[ 55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[ 55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[ 56.000626] Code: bad PC value
[ 56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for compal-laptop.c]
Acked-by: Darren Hart <dvhart@linux.intel.com>
[for the mfd part]
Acked-by: Lee Jones <lee.jones@linaro.org>
[for the hid part]
Acked-by: Jiri Kosina <jkosina@suse.cz>
[for the acpi part]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add new structure 'power_supply_config' for holding run-time
initialization data like of_node, supplies and private driver data.
The power_supply_register() function is changed so all power supply
drivers need updating.
When registering the power supply this new 'power_supply_config' should be
used instead of directly initializing 'struct power_supply'. This allows
changing the ownership of power_supply structure from driver to the
power supply core in next patches.
When a driver does not use of_node or supplies then it should use NULL
as config. If driver uses of_node or supplies then it should allocate
config on stack and initialize it with proper values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for drivers/platform/x86/compal-laptop.c]
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
[for drivers/hid/*]
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
According to [1], Windows Precision Touchpad devices must supply
a button type usage in the device capabilities feature report. A
value of 0 indicates that the device contains a depressible
button (i.e. it's a click-pad) whereas a value of 1 indicates
a non-depressible button. Add support for this usage and set
INPUT_PROP_BUTTONPAD on the touchpad input device whenever a
depressible button is present.
[1] https://msdn.microsoft.com/en-us/library/windows/hardware/dn467314(v=vs.85).aspx
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Declare the POWER_SUPPLY_PROP_PRESENT property to provide userspace
with a way to determine if the battery on a wireless tablet is plugged
in. Although current wireless tablets do not explicitly report this
information, it can be inferred from other state information. In
particular, a battery is assumed to be present if any of the following
are true: a non-zero battery level reported, the battery is reported as
charging, or the tablet is operating wirelessly.
Note: The last condition above may not strictly hold for the Graphire
Wireless (it charges from a DC barrel jack instead of a USB port), but I
do not know what is reported in the no-battery condition.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The constant is not used (leftover from previous patch versions
that never got merged).
Reported-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The status packet for tablets which can use a wireless module contains a
bit that is set if the battery is charging. This bit will be 0 if either
a battery is not present or if the battery has reached full charge. Note
that the charging circuit may continue to charge the battery for a short
time after reaching "100%".
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Calls the wacom_status_irq function to report battery status for the
Intuos Pro and Intuos5 (in addition to the already-reporting Intuos
and last-generation Bamboo).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If a wireless adapter (which contains the charging circuitry) is
detected as being attached to the tablet then create a new battery
interface and update its status as data is reported. Also destroy the
battery if the adapter goes away.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tablets like the Intuos, Intuos Pro, and Bamboo have a connector for an
optional wireless module that can be connected on the fly. The presence
(or absence) of this module is indicated in a status report recieved
from the tablet. This patch adds a workqueue function that will create
or destroy a power_supply object at runtime to match the current state
of the WACOM_QUIRK_BATTERY flag.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Has the 'wacom_notify_battery' function take on the job of detecting if
updating the power supply is necessary to remove multiple
nearly-identical 'if' blocks.
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In addition to the touchswitch state for "Intuos", these packets are
also sent by the Intuos Pro, Intuos5, and last-generation Bamboo
tablets when using a wired connection. They contain, among other
things, information about the optional wireless module and battery
charge state (to be supported in subsuquent patches).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Touchpads that have only one button are called clickpads and should
be advertised as such by the kernel.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Currently HID code maps usages from telephony page into BTN_0, BTN_1, etc
keys which get interpreted by mousedev and userspace as left/right/middle
button clicks, which is not really helpful.
This change adds mappings for usages that have corresponding input event
definitions, and leaves the rest unmapped. This can be changed when
there are userspace consumers for more telephony usages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In commit 08177f4 (HID: uclogic: merge hid-huion driver in hid-uclogic)
HID_HUION depends explicitely on USB_HID because it contained quite some
USB-isms.
Now that hid-uclogic is the new home of Huion tablets, we need to also
add the dependency on USB_HID to this driver.
Reported-by: Jiri Kosina <jkosina@suse.cz>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This hack is only needed for Huion tablets. It does not seem to have
any effect on the other tablets handled by this device right now, but
it's better to check for the product id sooner than discovering that
we have messed up one tablet later.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Huion tablets present 2 HID Pen interfaces. Only one is used, so
we can drop the unused one.
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NO_EMPTY_INPUT is useful when MULTI_INPUT is set. It prevents to create
empty input nodes that user space does not know what to do with.
It does not seem to be required at the moment, this is just a preventive
patch. This check is only made during the plug of the device, so it does
not hurt to have it.
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
We append "Pen", "Pad", "Mouse", "Keyboard", "Consumer Control" or
"System Control" suffix to the appropriate input node to match what
the Wacom driver does and be more convenient for the user to know
which one is which.
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Merge the hid-huion driver into hid-uclogic as all the devices supported
by hid-huion are in fact UC-Logic devices.
Signed-off-by: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on a patch from: Nikolai Kondrashov <Nikolai.Kondrashov@redhat.com>
Most of the tablets handled by hid-uclogic already use MULTI_INPUT.
For the ones which are not quirked in usbhid/hidquirks, they have a
custom report descriptor which contains only one report per HID
interface. For those tablets HID_QUIRK_MULTI_INPUT is transparent.
According to https://github.com/DIGImend/tablets, the only problematic
tablet currently handled by hid-uclogic is the TWHA60 v3. This tablet
presents different report descriptors from the ones currently quirked.
This is not a problem per se, given that this tablet is not supported
currently in this version (it needs the same command as a Huion to
start forwarding events).
Reviewed-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
touch_down is a flag to indicate if there are touches on tablet
or not. Since one set of touch events may be posted over more
than one data packet/touch frame, and pen may come in proximity
while touch events are partially sent, counting all touch events
for the set reflects the actual status of touch_down.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
If pen comes in proximity while touch is down, we force touch up
before sending pen events. Otherwise, there can be unfinished
touch events compete with pen events. This idea has been fully
implemented for Tablet PCs. But other tablets that support both
pen and touch are not fully considered.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The stylus of this device works just fine out of the box.
The touch is seen by default as a mouse with relative events and some
gestures.
The wireless and the wired version have slightly different firmwares, but
the debug mode 2 on the feature 2 is common to the 2 devices. In this mode,
all the reports are emitted through the debug interface (pen, raw touch
and mouse emulation), so we have to re-route manually the events.
We keep the Pen interface as a HID_GENERIC one because it works, and only
parse the raw touches while discarding the mouse emulation & gestures.
Switching the default in raw mode allows us to have a consistent user
experience accross all the multitouch touchpads (and enable the touch part
of the devices).
Note that the buttons of this devices are reported through the touch
interface. There is no 'Pad' interface. It seemed more natural to have
the BTN_LEFT and BTN_RIGHT reported with the touch because they are
placed under the touch interface and it looks like they belong to the
touch part.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Bamboo PAD in debug mode needs to re-route events from the debug
interface to the Pen interface. This can be easily done with
hid_input_report(), but that means that we need to keep a reference to
the various hid_devices.
There should be only one touch and one pen interface per physical tablet,
so there is no need to keep a list of hid-devices, plain pointers are
sufficient.
Tested-by: Josep Sanchez Ferreres <josep.sanchez.ferreres@est.fib.upc.edu>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These 2 are left over from the USB dependency cleaning, so there is
no need to keep them.
[jkosina@suse.cz: fix filename]
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A touchpad may have firmware based palm detection code enabled which
suppresses 2D data from being reported when the firmware believes a palm is
on the touchpad. This functionality is meant to be used in mouse mode without
a driver. When a driver is present, the driver can do a better job of
determining if a contact is a palm. If this gesture is enabled on a touchpad
operating in rmi mode then the firmware will not properly clear the palm detect
interrupt, causing the touchpad to interrupt indefinately. This patch disables
the palm detect gesture when the touchpad is operating in rmi mode.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a finger is lifted from a Synaptics touchpad the firmware will continue
to interrupts for up to a second. These additional interrupts are know and
dribble interrupts. Since the data read from the touchpad does not change
the input subsystem only reports a single event. This makes the servicing of
dribble interrupts on Linux unnecessary. This patch simply disables dribble
interupts when configuring the touchpad.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The HID over I2C specification allows to have the interrupt for a HID
device to be GPIO instead of directly connected to the IO-APIC.
Add support for this so that when the driver does not find proper interrupt
number from the I2C client structure we check if it has ACPI GpioInt()
resource listed in _CRS. If it is found we convert it to an interrupt
number and use it instead.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Lenovo Thinkpad 10 has wacom digitizer connected as a I2C-HID device. Add
generic support for this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit exposes in sysfs the HID country code that is stored in the country
member of hid_device structure. It identifies the country code of localized
hardware.
For example some keyboards use it to exhibit the language of the key layout. It
helps the upper layer to identify the localized hardware and setup the correct
language to use.
For USB HID devices the country code comes for the HID descriptor and for
Bluetooth HID devices it is the HIDCountryCode attribute from the SDP database.
Signed-off-by: Olivier Gay <ogay@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
