Commit Graph

75358 Commits

Author SHA1 Message Date
Gwendal Grignou
13cc546be3 sata_sil24: prevent hba lockup when pass-through ATA commands are used
Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA
commands [where ATA_QCFLAG_RESULT_TF is set] are used while other
commands are active on other devices connected to the same port with a
Port Multiplier.  Due to a hardware bug, these commands must be sent
alone, like ATAPI commands.

Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:54:01 -05:00
FD Cami
fcb71f6f03 Update kernel parameter document for libata DMA mode setting knobs.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:55 -05:00
Tejun Heo
4ccd3329a2 libata: don't normalize UNKNOWN to NONE after reset
After non-classifying reset, ehc->classes[] could contain
ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for
consistency.  However, this causes unfortunate side effect for drivers
which have non-classifying hardresets (e.g. sata_nv) by making
hardreset report ATA_DEV_NONE for non-classifying resets and thus
makes EH believe that the port is unoccupied and recovery can be
skipped.  The end result is that after a device is swapped with
another one, the new device isn't attached after the old one is
detached.

This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after
non-classifying resets.  This fixes the above problem.  As UNKNOWN and
NONE are handled differently by only EH hotplug logic, this doesn't
cause other behavior changes.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:22 -05:00
Tejun Heo
2695e36616 libata-pmp: propagate timeout to host link
Timeout on downstream command may indicate transmission problem on
host link.  Propagate timeouts to host link.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:16 -05:00
Tejun Heo
8048307dbc libata-pmp: 4726 hates SRST
4726 hates SRST even on non-config ports.  Don't use it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:12 -05:00
Rod Whitby
af18374804 pata_ixp4xx_cf: fix compilation introduced by ata_port_desc() conversion
Fixes a compilation error caused by ata_port_desc() conversion
(cbcdd87593).

Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:53:10 -05:00
Alan Cox
36906d9bea pata_pdc202xx_old: Further fixups
Turns out distros always enabled burst mode and it is pretty essential so
do the same. Also sort out the post DMA mode restore properly.

My 20263 card now seems happy but needs some four drive tests done yet
(when I've persuaded the kernel not to hang in the edd boot code if I
plug them in ..)

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:53 -05:00
Alan Cox
277d72a374 libata-sff: PCI IRQ handling fix
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:51 -05:00
Tejun Heo
b14dabcdb6 sata_qstor: use hardreset instead of softreset
During conversion to new EH, sata_qstor was accidentaly changed to use
softreset, which is buggy on this chip, instead of hardreset.  This
patch updates sata_qstor such that it uses hardreset again.

This fixes bugzilla bug 9631.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:41 -05:00
Linus Torvalds
fd0b45dfd1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (36 commits)
  [ATM]: Check IP header validity in mpc_send_packet
  [IPV6]: IPV6_MULTICAST_IF setting is ignored on link-local connect()
  [CONNECTOR]: Don't touch queue dev after decrement of ref count.
  [SOCK]: Adds a rcu_dereference() in sk_filter
  [XFRM]: xfrm_algo_clone() allocates too much memory
  [FORCEDETH]: Fix reversing the MAC address on suspend.
  [NET]: mcs7830 passes msecs instead of jiffies to usb_control_msg
  [LRO] Fix lro_mgr->features checks
  [NET]: Clone the sk_buff 'iif' field in __skb_clone()
  [IPV4] ROUTE: ip_rt_dump() is unecessary slow
  [NET]: kaweth was forgotten in msec switchover of usb_start_wait_urb
  [NET] Intel ethernet drivers: update MAINTAINERS
  [NET]: Make ->poll() breakout consistent in Intel ethernet drivers.
  [NET]: Stop polling when napi_disable() is pending.
  [NET]: Fix drivers to handle napi_disable() disabling interrupts.
  [NETXEN]: Fix ->poll() done logic.
  mac80211: return an error when SIWRATE doesn't match any rate
  ssb: Fix probing of PCI cores if PCI and PCIE core is available
  [NET]: Do not check netif_running() and carrier state in ->poll()
  [NET]: Add NAPI_STATE_DISABLE.
  ...
2008-01-09 08:05:12 -08:00
Roland McGrath
fcfd50afb6 show_task: real_parent
The show_task function invoked by sysrq-t et al displays the
pid and parent's pid of each task.  It seems more useful to
show the actual process hierarchy here than who is using
ptrace on each process.

Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-09 08:03:58 -08:00
Herbert Xu
1c9b7aa1eb [ATM]: Check IP header validity in mpc_send_packet
Al went through the ip_fast_csum callers and found this piece of code
that did not validate the IP header.  While root crashing the machine
by sending bogus packets through raw or AF_PACKET sockets isn't that
serious, it is still nice to react gracefully.

This patch ensures that the skb has enough data for an IP header and
that the header length field is valid.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-09 03:51:59 -08:00
Brian Haley
1ac4f00885 [IPV6]: IPV6_MULTICAST_IF setting is ignored on link-local connect()
Signed-off-by: Brian Haley <brian.haley@hp.com>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:52:21 -08:00
Li Zefan
cf585ae8ae [CONNECTOR]: Don't touch queue dev after decrement of ref count.
cn_queue_free_callback() will touch 'dev'(i.e. cbq->pdev), so it
should be called before atomic_dec(&dev->refcnt).

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:44:44 -08:00
Eric Dumazet
9d3e44425e [SOCK]: Adds a rcu_dereference() in sk_filter
It seems commit fda9ef5d67 introduced a RCU 
protection for sk_filter(), without a rcu_dereference()

Either we need a rcu_dereference(), either a comment should explain why we 
dont need it. I vote for the former.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:41:28 -08:00
Eric Dumazet
0f99be0d11 [XFRM]: xfrm_algo_clone() allocates too much memory
alg_key_len is the length in bits of the key, not in bytes.

Best way to fix this is to move alg_len() function from net/xfrm/xfrm_user.c 
to include/net/xfrm.h, and to use it in xfrm_algo_clone()

alg_len() is renamed to xfrm_alg_len() because of its global exposition.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:39:06 -08:00
Bjrn Steinbrink
2e3884b5b1 [FORCEDETH]: Fix reversing the MAC address on suspend.
For cards that initially have the MAC address stored in reverse order,
the forcedeth driver uses a flag to signal whether the address was
already corrected, so that it is not reversed again on a subsequent
probe.

Unfortunately this flag, which is stored in a register of the card,
seems to get lost during suspend, resulting in the MAC address being
reversed again. To fix that, the MAC address needs to be written back
in reversed order before we suspend and the flag needs to be reset.

The flag is still required because at least kexec will never write
back the reversed address and thus needs to know what state the card
is in.

Signed-off-by: Bjrn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:20 -08:00
Russ Dill
1d39da3dca [NET]: mcs7830 passes msecs instead of jiffies to usb_control_msg
usb_control_msg was changed long ago (2.6.12-pre) to take milliseconds
instead of jiffies. Oddly, mcs7830 wasn't added until 2.6.19-rc3.

Signed-off-by: Russ Dill <Russ.Dill@asu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:19 -08:00
Brice Goglin
877364e60e [LRO] Fix lro_mgr->features checks
lro_mgr->features contains a bitmask of LRO_F_* values which are
defined as power of two, not as bit indexes.
They must be checked with x&LRO_F_FOO, not with test_bit(LRO_F_FOO,&x).

Signed-off-by: Brice Goglin <Brice.Goglin@inria.fr>
Acked-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:18 -08:00
Paul Moore
02f1c89d6e [NET]: Clone the sk_buff 'iif' field in __skb_clone()
Both NetLabel and SELinux (other LSMs may grow to use it as well) rely
on the 'iif' field to determine the receiving network interface of
inbound packets.  Unfortunately, at present this field is not
preserved across a skb clone operation which can lead to garbage
values if the cloned skb is sent back through the network stack.  This
patch corrects this problem by properly copying the 'iif' field in
__skb_clone() and removing the 'iif' field assignment from
skb_act_clone() since it is no longer needed.

Also, while we are here, put the assignments in the same order as the
offsets to reduce cacheline bounces.

Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:17 -08:00
Eric Dumazet
d8c9283089 [IPV4] ROUTE: ip_rt_dump() is unecessary slow
I noticed "ip route list cache x.y.z.t" can be *very* slow.

While strace-ing -T it I also noticed that first part of route cache
is fetched quite fast :

recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202
GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3772 <0.000047>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\234\0\0\0\30\0\2\0\254i\
202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3736 <0.000042>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\204\0\0\0\30\0\2\0\254i\
202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3740 <0.000055>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\234\0\0\0\30\0\2\0\254i\
202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3712 <0.000043>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\204\0\0\0\30\0\2\0\254i\
202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3732 <0.000053>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202
GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3708 <0.000052>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202
GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3680 <0.000041>

while the part at the end of the table is more expensive:

recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\204\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3656 <0.003857>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\204\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3772 <0.003891>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3712 <0.003765>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3700 <0.003879>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3676 <0.003797>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"p\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\2\0\2\0"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3724 <0.003856>
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\234\0\0\0\30\0\2\0\254i\202GXm\0\0\2  \0\376\0\0\1\0\2"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 3736 <0.003848>

The following patch corrects this performance/latency problem,
removing quadratic behavior.

Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:16 -08:00
Russ Dill
2b2b2e35b7 [NET]: kaweth was forgotten in msec switchover of usb_start_wait_urb
Back in 2.6.12-pre, usb_start_wait_urb was switched over to take
milliseconds instead of jiffies. kaweth.c was never updated to match.

Signed-off-by: Russ Dill <Russ.Dill@asu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:15 -08:00
Auke Kok
204246596b [NET] Intel ethernet drivers: update MAINTAINERS
Unfortunately Jeb decided to move away from our group. We wish Jeb
good luck with his new group!

Reordered people a bit so most active team members are on top.

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:15 -08:00
David S. Miller
53e52c729c [NET]: Make ->poll() breakout consistent in Intel ethernet drivers.
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.

Now they will all break out when the amount of RX work done is less
than 'budget'.

At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this).  But if so, it should be done consistently
across the board to all of these drivers.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
2008-01-08 23:30:14 -08:00
David S. Miller
fed17f3094 [NET]: Stop polling when napi_disable() is pending.
This finally adds the code in net_rx_action() to break out of the
->poll()'ing loop when a napi_disable() is found to be pending.

Now, even if a device is being flooded with packets it can be cleanly
brought down.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:13 -08:00
David S. Miller
d1d08d1265 [NET]: Fix drivers to handle napi_disable() disabling interrupts.
When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.

And this is exactly what we want.  If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.

When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.

And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.

The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts.  In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.

However there were three exceptions to this in PCNET32, R8169, and
SKY2.  To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by:  Don Fry <pcnet32@verizon.net>
2008-01-08 23:30:12 -08:00
David S. Miller
1706287f6e [NETXEN]: Fix ->poll() done logic.
If work_done >= budget we should always elide the NAPI
completion.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:11 -08:00
Andrew Lutomirski
5cdfed54e7 mac80211: return an error when SIWRATE doesn't match any rate
Currently mac80211 fails silently when trying to set a nonexistent
rate.  Return an error instead.

Signed-Off-By: Andy Lutomirski <luto@myrealbox.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-08 23:30:10 -08:00
Michael Buesch
87c4ac841c ssb: Fix probing of PCI cores if PCI and PCIE core is available
This will make sure that always the correct core is selected, even if
there are both a PCI and PCI-E core on a PCI or PCI-E card.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-08 23:30:10 -08:00
David S. Miller
4ec2411980 [NET]: Do not check netif_running() and carrier state in ->poll()
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.

Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:09 -08:00
David S. Miller
a0a46196cd [NET]: Add NAPI_STATE_DISABLE.
Create a bit to signal that a napi_disable() is in progress.

This sets up infrastructure such that net_rx_action() can generically
break out of the ->poll() loop on a NAPI context that has a pending
napi_disable() yet is being bombed with packets (and thus would
otherwise poll endlessly and not allow the napi_disable() to finish).

Now, what napi_disable() does is first set the NAPI_STATE_DISABLE bit
(to indicate that a disable is pending), then it polls for the
NAPI_STATE_SCHED bit, and once the NAPI_STATE_SCHED bit is acquired
the NAPI_STATE_DISABLE bit is cleared.  Here, the test_and_set_bit()
provides the necessary memory barrier between the various bitops.

napi_schedule_prep() now tests for a pending disable as it's first
action and won't try to obtain the NAPI_STATE_SCHED bit if a disable
is pending.

As a result, we can remove the netif_running() check in
netif_rx_schedule_prep() because the NAPI disable pending state serves
this purpose.  And, it does so in a NAPI centric manner which is what
we really want.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:07 -08:00
David S. Miller
bdb95b1792 [NET]: Do not grab device reference when scheduling a NAPI poll.
It is pointless, because everything that can make a device go away
will do a napi_disable() first.

The main impetus behind this is that now we can legally do a NAPI
completion in generic code like net_rx_action() which a following
changeset needs to do.  net_rx_action() can only perform actions
in NAPI centric ways, because there may be a one to many mapping
between NAPI contexts and network devices (SKY2 is one example).

We also want to get rid of this because it's an extra atomic in the
NAPI paths, and also because it is one of the last instances where the
NAPI interfaces care about net devices.

The one remaining netdev detail the NAPI stuff cares about is the
netif_running() check which will be killed off in a subsequent
changeset.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:07 -08:00
Michael Buesch
d987160b71 b43: Fix rxheader channel parsing
This patch fixes the parsing of the RX data header channel field.

The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2008-01-08 23:30:06 -08:00
maximilian attems
9e8d6f8959 [IRDA]: irda_create() nuke user triggable printk
easy to trigger as user with sfuzz.

irda_create() is quiet on unknown sock->type,
match this behaviour for SOCK_DGRAM unknown protocol

Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:05 -08:00
Vlad Yasevich
036b579b11 [SCTP]: Add back the code that accounted for FORWARD_TSN parameter in INIT.
Some recent changes completely removed accounting for the FORWARD_TSN
parameter length in the INIT and INIT-ACK chunk.  This is wrong and
should be restored.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:04 -08:00
Vlad Yasevich
6df9cfc1ad [SCTP]: Correctly handle AUTH parameters in unexpected INIT
When processing an unexpected INIT chunk, we do not need to
do any preservation of the old AUTH parameters.  In fact,
doing such preservations will nullify AUTH and allow connection
stealing.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:03 -08:00
Vlad Yasevich
f691724c4d [SCTP]: Fix the name of the authentication event.
The even should be called SCTP_AUTHENTICATION_INDICATION.

Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:02 -08:00
Chas Williams
52961955aa [ATM]: [nicstar] delay irq setup until card is configured
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:01 -08:00
Stephen Hemminger
c6a1b62de9 [TULIP]: NAPI full quantum bug.
This should fix the kernel warn/oops reported while routing.

The tulip driver has a fencepost bug with new NAPI in 2.6.24
It has an off by one bug if a full quantum is reached.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:01 -08:00
Thomas Bogendoerfer
edba2a1fef [METH]: Fix MAC address handling.
meth didn't set a valid mac address during probing, but later during
open. Newer kernel refuse to open device with 00:00:00:00:00:00 as mac
address -> dead ethernet. This patch sets the mac address in the probe
function and uses only the mac address from the netdevice struct when
setting up the hardware.

Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:30:00 -08:00
Adrian Bunk
9a262d5c24 [NET]: Fix netx-eth.c compilation.
This was missed when commit e2ac455a18
fixed the compile errors in drivers/net/netx-eth.c caused by
commit 09f75cd7bf.

Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:59 -08:00
Amos Waterland
92ffb85dd3 [IPV4] ipconfig: Fix regression in ip command line processing
The recent changes for ip command line processing fixed some problems
but unfortunately broke some common usage scenarios.  In current
2.6.24-rc6 the following command line results in no IP address
assignment, which is surely a regression:

 ip=10.0.2.15::10.0.2.2:255.255.255.0::eth0:off

Please find below a patch that works for all cases I can find.

Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:58 -08:00
Herbert Xu
f844c74fe0 [IPV4] raw: Strengthen check on validity of iph->ihl
We currently check that iph->ihl is bounded by the real length and that
the real length is greater than the minimum IP header length.  However,
we did not check the caes where iph->ihl is less than the minimum IP
header length.

This breaks because some ip_fast_csum implementations assume that which
is quite reasonable.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:57 -08:00
David S. Miller
cb77df3ec8 [NIU]: Update driver version and release date.
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:56 -08:00
David S. Miller
3ebebccf89 [NIU]: Fix potentially stuck TCP socket send queues.
It is possible for the TX ring to have packets sit in it for unbounded
amounts of time.

The only way to defer TX interrupts in the chip is to periodically set
"mark" bits, when processing of a TX descriptor with the mark bit set
is complete it triggers the interrupt for the TX queue's LDG.

A consequence of this kind of scheme is that if packet flow suddenly
stops, the remaining TX packets will just sit there.

If this happens, since those packets could be charged to TCP socket
send queues, such sockets could get stuck.

The simplest solution is to divorce the socket ownership of the packet
once the device takes the SKB, by using skb_orphan() in
niu_start_xmit().

In hindsight, it would have been much nicer if the chip provided two
interrupt sources for TX (like basically every other ethernet chip
does).  Namely, keep the "mark" bit, but also signal the LDG when the
TX queue becomes completely empty.  That way there is no need to have
a deadlock breaker like this.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:56 -08:00
David S. Miller
792dd90f11 [NIU]: Missing ->last_rx update.
Noticed by Paul Lodridge.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:55 -08:00
Matheos Worku
406f353c85 [NIU]: Fix slowpath interrupt handling.
niu_slowpath_interrupt() expects values to be setup in lp->{v0,v1,v2}
but they aren't.  That's only done by niu_schedule_napi() which is
done later in the interrupt path.

If niu_rx_error() returns zero, and v0 is clear, hit the
RX_DMA_CTL_STATE register with a RX_DMA_CTL_STAT_MEX.

Only emit verbose RX error logs if a fatal channel or port error is
signalled.  Other cases will be recorded into statistics by
niu_log_rxchan_errors().

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-08 23:29:54 -08:00
Thomas Gleixner
cdf71a10c7 futex: Prevent stale futex owner when interrupted/timeout
Roland Westrelin did a great analysis of a long standing thinko in the
return path of futex_lock_pi.

While we fixed the lock steal case long ago, which was easy to trigger,
we never had a test case which exposed this problem and stupidly never
thought about the reverse lock stealing scenario and the return to user
space with a stale state.

When a blocked tasks returns from rt_mutex_timed_locked without holding
the rt_mutex (due to a signal or timeout) and at the same time the task
holding the futex is releasing the futex and assigning the ownership of
the futex to the returning task, then it might happen that a third task
acquires the rt_mutex before the final rt_mutex_trylock() of the
returning task happens under the futex hash bucket lock. The returning
task returns to user space with ETIMEOUT or EINTR, but the user space
futex value is assigned to this task. The task which acquired the
rt_mutex fixes the user space futex value right after the hash bucket
lock has been released by the returning task, but for a short period of
time the user space value is wrong.

Detailed description is available at:

   https://bugzilla.redhat.com/show_bug.cgi?id=400541

The fix for this is the same as we do when the rt_mutex was acquired by
a higher priority task via lock stealing from the designated new owner.
In that case we already fix the user space value and the internal
pi_state up before we return. This mechanism can be used to fixup the
above corner case as well. When the returning task, which failed to
acquire the rt_mutex, notices that it is the designated owner of the
futex, then it fixes up the stale user space value and the pi_state,
before returning to user space. This happens with the futex hash bucket
lock held, so the task which acquired the rt_mutex is guaranteed to be
blocked on the hash bucket lock. We can access the rt_mutex owner, which
gives us the pid of the new owner, safely here as the owner is not able
to modify (release) it while waiting on the hash bucket lock.

Rename the "curr" argument of fixup_pi_state_owner() to "newowner" to
avoid confusion with current and add the check for the stale state into
the failure path of rt_mutex_trylock() in the return path of
unlock_futex_pi(). If the situation is detected use
fixup_pi_state_owner() to assign everything to the owner of the
rt_mutex.

Pointed-out-and-tested-by: Roland Westrelin <roland.westrelin@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-08 16:21:39 -08:00
Alan Cox
bf5e5834bf pl2303: Fix mode switching regression
Cleaning out all the incorrect 'no change made' checks for termios
settings showed up a problem with the PL2303. The hardware here seems to
lose sync and bits if you tell it to make no changes. This shows up with
a real world application.

To fix this the driver check for meaningful hardware changes is restored
but doing the tests correctly and as a tty layer function so it doesn't
get duplicated wrongly everywhere if other drivers turn out to need it.

Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mirko Parthey <mirko.parthey@informatik.tu-chemnitz.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-08 16:16:34 -08:00
Eric Sandeen
cf05946250 hfs: handle more on-disk corruptions without oopsing
hfs seems prone to bad things when it encounters on disk corruption.  Many
values are read from disk, and used as lengths to memcpy, as an example.
This patch fixes up several of these problematic cases.

o sanity check the on-disk maximum key lengths on mount
  (these are set to a defined value at mkfs time and shouldn't differ)
o check on-disk node keylens against the maximum key length for each tree
o fix hfs_btree_open so that going out via free_tree: doesn't wind
  up in hfs_releasepage, which wants to follow the very pointer
  we were trying to set up:
	HFS_SB(sb)->cat_tree = hfs_btree_open()
		...
		failure gets to hfs_releasepage and tries
		to follow HFS_SB(sb)->cat_tree

Tested with the fsfuzzer; it survives more than it used to.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-08 16:10:36 -08:00