This gets us closer to being able to eliminate the use
of dynamic and stack based buffers, so that we can adhere
to the "no buffer addresses above 4GB" rule for PROM calls.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'sparc32' ARCH target to test all{yes,mod}config for 32-bit build.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC arch/sparc/kernel/irq_32.o
arch/sparc/kernel/irq_32.c: In function 'request_fast_irq':
arch/sparc/kernel/irq_32.c:370:25: error: conflicting types for 'trapbase_cpu1'
arch/sparc/include/asm/leon.h:366:22: note: previous declaration of 'trapbase_cpu1' was here
arch/sparc/kernel/irq_32.c:370:40: error: conflicting types for 'trapbase_cpu2'
arch/sparc/include/asm/leon.h:367:22: note: previous declaration of 'trapbase_cpu2' was here
arch/sparc/kernel/irq_32.c:370:55: error: conflicting types for 'trapbase_cpu3'
arch/sparc/include/asm/leon.h:368:22: note: previous declaration of 'trapbase_cpu3' was here
make[3]: *** [arch/sparc/kernel/irq_32.o] Error 1
make[2]: *** [arch/sparc/kernel] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove HAVE_PERF_EVENTS and PERF_USE_VMALLOC under config
SPARC because they're under SPARC64 too. Supporting
perf_event needs atomic64 operations but AFAIK sparc32
doesn't provide them, CMIIW. ;-) Also removes redundant
HAVE_IRQ_WORK line.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that #include <asm/system.h> makes a circular dependency
between kernel.h and bitmap.h which breaks allmodconfig build.
Removing the line makes no change because jump_label.h doesn't
need it actually AFAICS. Compile tested on sparc32 allmodconfig.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rett stack checking code sees the stack is unaligned (in both
the sun4c and srmmu cases) it jumps to the window fault-in path.
But that just tries to page the stack pages in, it doesn't do anything
special if the stack is misaligned.
Therefore we essentially just loop forever in the trap return path.
Fix this by emitting a SIGILL in the stack fault-in code if the stack
is mis-aligned.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Analog of what commit 494486a1d2 had done
to alpha (another architecture with similar bug).
One note: in rtrap_32.S part clr %l6 has been a rudiment of left after
commit 28e6103665 (sparc: Fix debugger syscall
restart interactions) has killed %l6 use in there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits)
microblaze: Fix build with make 3.82
fbdev/xilinxfb: Microblaze driver support
microblaze: Support C optimized lib functions for little-endian
microblaze: Separate library optimized functions
microblaze: Support timer on AXI lite
microblaze: Add support for little-endian Microblaze
microblaze: KGDB little endian support
microblaze: Add PVR for endians plus detection
net: emaclite: Add support for little-endian platforms
microblaze: trivial: Add comment for AXI pvr
microblaze: pci-common cleanup
microblaze: Support early console on uart16550
microblaze: Do not compile early console support for uartlite if is disabled
microblaze: Setup early console dynamically
microblaze: Rename all uartlite early printk functions
microblaze: remove early printk uarlite console dependency from header
microblaze: Remove additional compatible properties
microblaze: Remove hardcoded asm instraction for PVR loading
microblaze: Use static const char * const where possible
microblaze: Define VMALLOC_START/END
...
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: lis3: Release resources in case of failure
hwmon: lis3: Short explanations of platform data fields
hwmon: lis3: Enhance lis3 selftest with IRQ line test
hwmon: lis3: use block read to access data registers
hwmon: lis3: Adjust fuzziness for 8 bit device
hwmon: lis3: New parameters to platform data
hwmon: lis3: restore axis enabled bits
hwmon: lis3: Power on corrections
hwmon: lis3: Update coordinates at polled device open
hwmon: lis3: Cleanup interrupt handling
hwmon: lis3: regulator control
hwmon: lis3: pm_runtime support
Kirkwood: add fan support for Network Space Max v2
hwmon: add generic GPIO fan driver
hwmon: (coretemp) fix reading of microcode revision (v2)
hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs
hwmon: (pkgtemp) align driver initialization style with coretemp
hwmon: LTC4261 Hardware monitoring driver
hwmon: (lis3) add axes module parameter for custom axis-mapping
hwmon: (hp_accel) Add HP Mini 510x family support
...
In the MN10300 arch, we occasionally see an assertion being tripped in
alloc_cwqs() at the following line:
/* just in case, make sure it's actually aligned */
---> BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align));
return wq->cpu_wq.v ? 0 : -ENOMEM;
The values are:
wa->cpu_wq.v => 0x902776e0
align => 0x100
and align is calculated by the following:
const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS,
__alignof__(unsigned long long));
This is because the pointer in question (wq->cpu_wq.v) loses some of its
lower bits to control flags, and so the object it points to must be
sufficiently aligned to avoid the need to use those bits for pointing to
things.
Currently, 4 control bits and 4 colour bits are used in normal
circumstances, plus a debugging bit if debugging is set. This requires
the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512
bytes aligned with debugging).
PERCPU() alignment on MN13000, however, is only 32 bytes as set in
vmlinux.lds.S. So we set this to PAGE_SIZE (4096) to match most other
arches and stick a comment in alloc_cwqs() for anyone else who triggers
the assertion.
Reported-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mark Salter <msalter@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If lis3lv02d_init_device fails, HW resources were not released
properly. In case of failure call release_resources if available.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
No one uses these MMRs so we didn't notice when the anomaly handling
logic was inverted.
Reported-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This code was useful during early port development when our icache code
wasn't solid, but that ship has sailed long ago, and no code calls this
function anymore (irq_panic). So punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Configure chip to data ready mode in selftest and count received
interrupts to see that interrupt line(s) are working.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add optional blockread function to interface driver. If available
the chip driver uses it for data register access. For 12 bit device
it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out
5 bytes since every second byte is dummy.
This optimizes bus usage and reduces number of operations and
interrupts needed for one data update.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Default fuziness is set smaller for 8 device.
In 12 bit device LSB is quite close to 1 mg
(mg = 1 / 1000 of earth gravity).
In 8bit device LSB is about 18 mg.
Set fuziness to 1 for 8 bit device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Added default output data rate setting to platform data.
If default rate is 0, reset default value is used.
Added control for duration via platform data.
Added possibility to configure interrupts to trig on
both rising and falling edge. The lis3 WU unit can be
configured quite many ways and with some configurations it
is quite handy to get coordinate refresh when some
event trigs and when it reason goes away.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
All axis enable bits are set to 0 at module remove.
Restore reset default value at init.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Sometimes lis3 chip seems to fail to setup factory tuning at boot up.
This probably happens if there is some odd power ramp down ramp up sequence
for example in device restart. Set boot bit in control2 register to
trig boot sequence manually and wait until it is finished.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Call input device poll function at device open to refresh coordinates
immediately. This is needed for the case where poll interval is set to
zero and coordinate updates happens purely under interrupt control.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Irqcfg moved to chip data instead of platform data.
This simplifies access in interrupt handler little bit.
Input device open and close functions set status for
interrupt threaded handler once.
Unnecessary check for interrupt source removed since
it is enough that active interrupt line indicates that
there was an interrupt.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Based on pm_runtime control, turn lis3 regulators on and off.
Perform context save and restore on transitions.
Feature is optional and must be enabled in platform data.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add pm_runtime support to lis3 core driver.
Add pm_runtime support to lis3 i2c driver.
spi and hp_accel drivers are not yet supported. Old always
on functionality remains for those.
For sysfs there is 5 second delay before turning off the
chip to avoid long ramp up delay.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch adds hwmon support for fans connected to GPIO lines.
Platform specific information such as GPIO pinout and speed conversion array
(rpm from/to GPIO value) are passed to the driver via platform_data.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
According to the documentation, simply reading the respective MSR
isn't sufficient: It should be written with zeros, cpuid(1) be
executed, and then read (see arch/x86/kernel/cpu/intel.c for an
example).
v2: Fail probe when microcode revision cannot be determined, but is
needed to check for proper operation.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
CONFIG_HOTPLUG_CPU is used too much in some drivers.
This patch clean them up.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pkgtemp is derived from coretemp, so some reasonable
logics should be applied onto pkgtemp, too. Such as
the init logic here.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The axis-mapping of lis3dev device on many (rather most) HP machines
doesn't follow the standard. When each new model appears, users need to
adjust again. Testing this requires the rebuild of kernel, thus it's not
trivial for end-users.
This patch adds a module parameter "axes" to allow a custom axis-mapping
without patching and recompiling the kernel driver. User can pass the
parameter such as axes=3,2,1. Also it can be changed via sysfs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch is an enhanced version of Takashi Iwai's
[PATCH] hp_accel: Add quirks for HP ProBook 532x and HP Mini 5102
My HP Mini 5101 works fine with this patch.
Confirmed with Tux Racer.
Signed-off by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A new version of LIS3 chip has slight incompatibilities from former
versions. This patch adds the minimal support for it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
These likely originate from these drivers being clones of one another
and/or other drivers which actually needed these includes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
"break" after "return" is at best bogus (good compilers even warn about
the "break" being unreachable).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
... as they're being called only from a __cpuinit function.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'nfs-for-2.6.37' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: (67 commits)
SUNRPC: Cleanup duplicate assignment in rpcauth_refreshcred
nfs: fix unchecked value
Ask for time_delta during fsinfo probe
Revalidate caches on lock
SUNRPC: After calling xprt_release(), we must restart from call_reserve
NFSv4: Fix up the 'dircount' hint in encode_readdir
NFSv4: Clean up nfs4_decode_dirent
NFSv4: nfs4_decode_dirent must clear entry->fattr->valid
NFSv4: Fix a regression in decode_getfattr
NFSv4: Fix up decode_attr_filehandle() to handle the case of empty fh pointer
NFS: Ensure we check all allocation return values in new readdir code
NFS: Readdir plus in v4
NFS: introduce generic decode_getattr function
NFS: check xdr_decode for errors
NFS: nfs_readdir_filler catch all errors
NFS: readdir with vmapped pages
NFS: remove page size checking code
NFS: decode_dirent should use an xdr_stream
SUNRPC: Add a helper function xdr_inline_peek
NFS: remove readdir plus limit
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
