No need to read the PCI register for the PF's base queue on every single Tx
queue enable and disable as we already have the value stored from reading
the capability features at startup.
Change-ID: Ic02fb622757742f43cb8269369c3d972d4f66555
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A drop action comes down as a ring_cookie value, so allow it as
a special value that can be used to configure destination control.
Also fix the output to filter read command accordingly.
Change-ID: I9956723cee42f3194885403317dd21ed4a151144
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.
Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change drops the FTYPE field from the Rx descriptor, to
match the hardware implementation.
Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FW can indicate any admin queue error states to the driver via some bits
in the length registers. Each time we process an admin queue message,
check these bits and log any errors we find. Since the VF really can't
do much, we just print the message and depend on the PF driver to clear
things up on our behalf.
Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default. The system
must request a VLAN tag packet filter to get packets with that tag.
Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.
This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.
Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().
Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In XL710 devices we program FD filter's fields from Tx perspective of the flow.
However the user interface exposed in ethtool should be compliant with the
previous generation of drivers where a filter src and dst field are from
the RX perspective. This patch changes the ethtool interface in this regard
to match the other drivers.
Change-ID: Iec6ccddd87357c4fb53ccf33aa0fae699faf70cf
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add set_pf_context, replace set_phy_reset with set_phy_debug, add
nvm_config_read/write, remove nvm_read/write_reg_se and add some
PHY types.
With these changes we bump the API version to 1.2.
Change-ID: I4dc3aec175c2316f66fc9b726b3f7d594699d84e
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set appropriate fields in Tx queue configuration virtchnl message
to pf to enable headwb and setup headwb addr.
Then use that info from the VF to set headwb and headwb_addr instead of
always enabling them.
Change-ID: I7d393d1b2b07f0f3355b3a4f7c2d3c6ee3b0d622
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch separates the hardware logic from the set function, so that
we can re-use it during a ptp_reset. This enables the reset to return
functionality to the last known timestamp mode, rather than resetting
the value. We initialize the mode to off during the ptp_init cycle.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return a 0 directly rather than a constant.
Reported-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
MAX_DMA_CHANNELS is defined in asm/scatterlist.h of the powerpc
architecture. Rename this #define in xgbe.h to avoid the
redefined warning issued during compilation.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commit befdf89 "net/mlx4_core: Preserve pci_dev_data after
__mlx4_remove_one()", there are two mlx4 pci callbacks which will
attempt to release the mlx4_priv object -- .shutdown and .remove.
This leads to a use-after-free access to the already freed mlx4_priv
instance and trigger a "Kernel access of bad area" crash when both
.shutdown and .remove are called.
During reboot or kexec, .shutdown is called, with the VFs probed to
the host going through shutdown first and then the PF. Later, the PF
will trigger VFs' .remove since VFs still have driver attached.
Fix that by keeping only one driver entry which releases mlx4_priv.
Fixes: befdf89 ('net/mlx4_core: Preserve pci_dev_data after __mlx4_remove_one()')
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hypervisor driver tracks free slots and reserved slots at the global level
and tracks allocated slots and guaranteed slots per VF.
Guaranteed slots are treated as reserved by the driver, so the total
reserved slots is the sum of all guaranteed slots over all the VFs.
As VFs allocate resources, free (global) is decremented and allocated (per VF)
is incremented for those resources. However, reserved (global) is never changed.
This means that effectively, when a VF allocates a resource from its
guaranteed pool, it is actually reducing that resource's free pool (since
the global reserved count was not also reduced).
The fix for this problem is the following: For each resource, as long as a
VF's allocated count is <= its guaranteed number, when allocating for that
VF, the reserved count (global) should be reduced by the allocation as well.
When the global reserved count reaches zero, the remaining global free count
is still accessible as the free pool for that resource.
When the VF frees resources, the reverse happens: the global reserved count
for a resource is incremented only once the VFs allocated number falls below
its guaranteed number.
This fix was developed by Rick Kready <kready@us.ibm.com>
Reported-by: Rick Kready <kready@us.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A check on a memory allocation is checked incorrectly.
This was partly found using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed a bug that shows up with recv window sizes that exceed the size of
the RCV_BUFSIZ field in opt0 (>= 1024K). If the recv window exceeds
this, then we specify the max possible in opt0, add add the rest in via
a RX_DATA_ACK credits.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Select the appropriate hw mtu index and initial sequence number to optimize
hw memory performance.
Add new cxgb4_best_aligned_mtu() which allows callers to provide enough
information to be used to [possibly] select an MTU which will result in the
TCP Data Segment Size (AKA Maximum Segment Size) to be an aligned value.
If an RTR message exhange is required, then align the ISS to 8B - 1 + 4, so
that after the SYN the send seqno will align on a 4B boundary. The RTR
message exchange will leave the send seqno aligned on an 8B boundary.
If an RTR is not required, then align the ISS to 8B - 1. The goal is
to have the send seqno be 8B aligned when we send the first FPDU.
Based on original work by Casey Leedom <leeedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently indirect interrupts for RDMA CQs funnel through the LLD's RDMA
RXQs, which also handle direct interrupts for offload CPLs during RDMA
connection setup/teardown. The intended T4 usage model, however, is to
have indirect interrupts flow through dedicated IQs. IE not to mix
indirect interrupts with CPL messages in an IQ. This patch adds the
concept of RDMA concentrator IQs, or CIQs, setup and maintained by the
LLD and exported to iw_cxgb4 for use when creating CQs. RDMA CPLs will
flow through the LLD's RDMA RXQs, and CQ interrupts flow through the
CIQs.
Design:
cxgb4 creates and exports an array of CIQs for the RDMA ULD. These IQs
are sized according to the max available CQs available at adapter init.
In addition, these IQs don't need FL buffers since they only service
indirect interrupts. One CIQ is setup per RX channel similar to the
RDMA RXQs.
iw_cxgb4 will utilize these CIQs based on the vector value passed into
create_cq(). The num_comp_vectors advertised by iw_cxgb4 will be the
number of CIQs configured, and thus the vector value will be the index
into the array of CIQs.
Based on original work by Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- Fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- A pile of SRP initiator fixes from Bart Van Assche.
- Fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- The usual fixes and cleanups to mlx4, mlx5, cxgb4 and other
low-level drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wcdc
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull main InfiniBand/RDMA updates from Roland Dreier:
- add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- a pile of SRP initiator fixes from Bart Van Assche.
- fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- the usual fixes and cleanups to mlx4, mlx5, cxgb4 and other low-level
drivers.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (61 commits)
RDMA/cxgb4: Add support for iWARP Port Mapper user space service
RDMA/nes: Add support for iWARP Port Mapper user space service
RDMA/core: Add support for iWARP Port Mapper user space service
IB/mlx4: Fix gfp passing in create_qp_common()
IB/umad: Fix use-after-free on close
IB/core: Fix kobject leak on device register error flow
RDMA/cxgb4: add missing padding at end of struct c4iw_alloc_ucontext_resp
mlx4_core: Fix GFP flags parameters to be gfp_t
IB/core: Fix port kobject deletion during error flow
IB/core: Remove unneeded kobject_get/put calls
IB/core: Fix sparse warnings about redeclared functions
IB/mad: Fix sparse warning about gfp_t use
IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
IB: Add a QP creation flag to use GFP_NOIO allocations
IB: Return error for unsupported QP creation flags
IB: Allow build of hw/ and ulp/ subdirectories independently
mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
RDMA/cxgb4: Add missing padding at end of struct c4iw_create_cq_resp
IB/srp: Avoid problems if a header uses pr_fmt
IB/umad: Fix error handling
...
Bumpity and Fred Worm say it's time to change the numbers again.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I658731d022ea23cedede4be2bfecd8b4cc68d270
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We tell the HW upper boundary of power of 2 in VSI config,
but the HW does not restrict us to use just power of 2 GPS in
case of RSS as long as we are not sharing the RSS table with
another VSI (VMDq). We at present are not doing RSS in VMDq
VSI.
If we were to enable that and if the system had CPU count which
was not power 2, the VMDq VSIs will see a little skewed distribution.
Change-ID: I3ea797ce9065a3ca4fc4d04251bf195463410473
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delete all the old and stale MAC filters for the VF VSI when the host
administrator changes the VF MAC address from under its feet. Also don't
bother to add a filter for the VSI when its going to go away anyway.
Just record the new address and punch the VF reset.
Change-ID: Ic0d12055926f41989d1965ccf500053729c063ad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FD_SB and FD_ATR needs to be checked independently in order to decide if
we will support multiple queues or not.
Change-ID: I9d3274f5924c79e29efdbcf66a2fcca1fee2107f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was not marking packets with bad checksums
correctly, especially IPv6 packets with a bad checksum.
To do this correctly we need a define that may be set by
hardware in rare cases.
Change-ID: I1a997b72b491ded27a78ac3bce1197b2d2611130
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Modify the logic in i40e_determine_queue_usage() so that
SR-IOV doesn't get turned off unnecessarily.
Change-ID: I86ca304fa9f742a50e9ea831b887f358a6a9d53d
Signed-off-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the way resources are distributed to special features.
Change-ID: I847e49d714a1d70e97f3f994cb39bfb5e02ab016
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Our hardware supports VF antispoofing for both MAC addresses and VLANs.
Enable this feature by default for all VFs and implement the netdev op
to control it from the command line.
Change-ID: Ifb941da22785848aa3aba6b2231be135b8ea8f31
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to complain in the log about mac addresses that
can't be deleted because they don't exist.
Change-ID: I4e6370df175bf72726f06d2206c03bcbfded8387
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was a vestige of early driver development that no longer
has any actual use.
Change-ID: I95b5b19c4bbfaff8759197af671ebaf716cb6ab5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of VSIs that the firmware reports to us is a guaranteed
minimum, not an absolute maximum. The hardware actually supports far
more than the reported value, which we often need.
To allow for this, we allocate space for a larger number of VSIs than is
guaranteed by the firmware, with the knowledge that we may fail to get
them all in the future.
Note that we are just allocating pointers here, the actual (much larger)
VSI structures are allocated on demand.
Change-ID: I6f4e535ce39d3bf417aef78306e04fbc7505140e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix function header comment to have the correct function name.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for error status bits on the AdminQ event queue and announce them
if seen. If the Firmware sets these bits, it will trigger an AdminQ
interrupt to get the driver's attention to process the ARQ, which will
likely be enough to clear the actual issue.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Change-ID: I009e0ebc8be764e40e193b29aed2863f43eb5cb0
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that 3.15 is released, this merges the 'next' branch into 'master',
bringing us to the normal situation where my 'master' branch is the
merge window.
* accumulated work in next: (6809 commits)
ufs: sb mutex merge + mutex_destroy
powerpc: update comments for generic idle conversion
cris: update comments for generic idle conversion
idle: remove cpu_idle() forward declarations
nbd: zero from and len fields in NBD_CMD_DISCONNECT.
mm: convert some level-less printks to pr_*
MAINTAINERS: adi-buildroot-devel is moderated
MAINTAINERS: add linux-api for review of API/ABI changes
mm/kmemleak-test.c: use pr_fmt for logging
fs/dlm/debug_fs.c: replace seq_printf by seq_puts
fs/dlm/lockspace.c: convert simple_str to kstr
fs/dlm/config.c: convert simple_str to kstr
mm: mark remap_file_pages() syscall as deprecated
mm: memcontrol: remove unnecessary memcg argument from soft limit functions
mm: memcontrol: clean up memcg zoneinfo lookup
mm/memblock.c: call kmemleak directly from memblock_(alloc|free)
mm/mempool.c: update the kmemleak stack trace for mempool allocations
lib/radix-tree.c: update the kmemleak stack trace for radix tree allocations
mm: introduce kmemleak_update_trace()
mm/kmemleak.c: use %u to print ->checksum
...
Bump i40e to 0.4.5 and i40evf to 0.9.29.
Change-ID: I9faca5544446518c5425612e733499cf16ef20a1
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove two device IDs 1582 and 1573, because they will not be shipped.
Change-ID: Ica2e550b5b21a69e3f353eba2fe5e1c532a548c4
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a coding error where during the registration for NAPI
the driver requested 256 budget. The max recommended
value for this is NAPI_POLL_WEIGHT or 64.
Change-ID: I03ea1e2934a84ff1b5d572988b18315d6d91c5c6
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The TSO logic in the transmit path had some assumptions that
have been broken now that the kernel can send as much as 32kB
in a single skb->frag[.] entry, even on a system with 4kB pages.
This fixes the assumptions and allows the kernel to operate
as efficiently as possible with both SENDFILE and SEND.
In addition, the hardware limit of data contained in a descriptor is
changed to the next power of two below where it currently is in
order to align to a power of two value, preventing a single byte
of data in a descriptor.
Change-ID: I6af1f0b87c1458e10644dbd47541591075a52651
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Both the PF side and the VF side of the VF reset process are too noisy.
We already warn the user that a reset is happening, and that is
sufficient.
Because some of these message are inside if statements, we have to
rejigger the brackets at the same time to keep our coding style
consistent.
Change-ID: Id175562fb0ec7c396d9de156b4890e136f52d5f4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Once more, with feeling: not all VSIs have rings. To assume so is to
invite null pointers to your party.
Change-ID: I576858824468d9712d119fa1015a1f28c27712c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Be sure to clear PXE mode bit on each reset after AdminQ has been rebuilt.
Change-ID: I992d8c79594f8ca0660c50844ace675ecb9c9bf2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where FD SB/ATR and NTUPLE configurations status are
reported erroneously. Without this patch, driver reports FDir without further
information.
Change-ID: I5bdd2871b7f2db1e5f5e76c741ae6a0dc603b453
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The correct format is %pM, not %pMAC.
Change-ID: Idb335723a966fe56db3a72b9c07c08ca66f9db3c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up inconsistent log messages, mostly related to punctuation. Based
on the dogma that "kernel messages are not sentences", remove all
trailing periods. Reword a few of the messages to make them less
sentence-like.
Change-ID: Ibd849aa7623a77549b0709988c66ab05d1311472
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This comment is just plain false. VF drivers require MSI-X or they won't
get interrupts at all.
Change-ID: Iaea5e30b6926948aa834a3c506d9a9223d9e3e29
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to print log messages when we encounter an out-of-memory
condition, as the allocator will do this for us. Also, remove a Tx hang
message that duplicates the one emitted by the netdev layer, and a
duplicate message in the watchdog.
Change-ID: If2056e6135fe248f66ea939778f9895660f4d189
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1. There is no ixgbe_watchdog_task function in the driver, so change
the comment to the correct function name, i40e_watchdog_subtask.
2. Remove num_msix_entries from interrupt set_up routine
because it is never used.
3. Remove some TBD comments that are not needed.
Change-ID: I37697a04007074b797f85fd83d626672e4df1ad1
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove use of registers no longer supported.
Change-ID: I9d27399091cea78a926489d94f958edd762f5a20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As reported by Eric Dumazet, the driver is not masking the right
bits in the receive descriptor before it starts checking them.
This patch extends the mask to allow for the right bits to be
checked, and fixes the issue permanently via a define.
CC: Eric Dumazet <eric.dumazet@gmail.com>
Change-ID: I3274f7619057a950f468143e6d7e11b129f54655
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The include of asm/cputype.h breaks the powerpc build. This
include was accidentally left in from driver debugging and
can be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>,
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump i40e to 0.4.3 and i40evf to 0.9.27.
Change-ID: I4141e9f8615bdcfa3b1b5ecbc2ac62603a03b7ad
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use an extra state variable to keep track of when the IRQs are fully
set up. This keeps us from trying to unhook IRQs that already were
left unhooked in a failed reset recovery, e.g. when firmware is broken.
Change-ID: I073eb081e4ef8aedcbdf1ee0717c0ed64fa172f2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a reset recovery failed (e.g. firmware is broken), the HMC space won't
get set up. We don't need to try to delete it if it didn't get set up.
This stops some needless error messages when we already know we need to
just tear things down.
Change-ID: Iac600481765e20b136052b43a544e55d7870268b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e driver should print link messages like all the
other Intel Ethernet drivers.
Change-ID: Ia88bdb96794e17a3962fcea94db176de01f921f7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the missing unicast, multicast, and broadcast stats for the port.
Change-ID: Ifc366d7b7745f70eaac9d00eeb0694eb9ec076a9
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add VSI HW stats for unicast, multicast, and broadcast for Rx and Tx.
Stop printing the netdev multicast value because it doesn't include Tx
and would be confusing.
Change-ID: I08278b6657e7c838fd29a4a1f305f78fe1b150be
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The wait time was originally too optimistic and the resets were failing
after EMPR. This increases the loop count to wait considerably longer.
This won't delay the actual wait longer than really needed, just allows
us to poll more times as needed.
Change-ID: If7b96f55cc25b8d06cbbe8665259d250188c53d7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a function which indicates our intention to enable or disable a particular
Tx queue. Also add a function to notify the device's Tx unit that we're about
to enable or disable a Tx queue.
Change-ID: I6adf3cbb5bb3e3c984d1ec969e06577c19ef296d
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
B0 Si blocks AQ registers when in Blank Flash mode - write is dropped,
read gives 0xDEADBEEF. Introduce a simple check for a correct value in one
of the AQ registers to be sure that AQ was configured correctly.
Without this check we get into an endless loop while trying to send
GetVersion AQ cmd.
Change-ID: I00102b8c5fa6c16d14289be677aafadf87f10f0d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Depending on the timing of what the PF driver is doing, it make take a
few tries before the VF driver is able to communicate with the PF driver
on init or reset recovery. In order to prevent confusion, make the most
common messages less scary by lowering them to a less terrifying log
level and indicate that the driver will retry.
Change-ID: I1ec22aa59a68f4469aabe14775a1bfc1ab4b7f2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver and hardware are not expected to work correctly
with revision_id 0 hardware. Don't prevent the user from
using it, but be sure to print a warning.
Change-ID: I3712d34752bfad458078a5f35dfd0aa0ae9fd20e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print the VEB statistics in the ethtool stats output.
Change-ID: Ic93d4c3922345c43e4cfd7f7e7a906844dd2f49f
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the VEB is created for the basic LAN device and its VSIs, we need to
set the tracking lan_veb index for later use.
Change-ID: I66bb74993bbda3621ca557437cb4b3517f9b315b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT driver uses libphy to determine the carrier state, so
make sure we start with a carrier off until libphy has completed the
link training process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comment about how the hardware prepends 2bytes to align the IP
header on a 4-byte boundary was not correct, fix that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were missing an and comparison with status to check whether
RX_STATUS_OVFLOW is asserted or not in the per-packet status word, fix
that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our transmit locking scheme did not account for the TX ring full
interrupt. If a TX ring full interrupt fires while we are attempting to
transmit, we will cause a deadlock to occur. Fix this by making sure
that we properly disable interrupts while acquiring the spinlock.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides the initial platform driver for the AMD
10GbE device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/amd/hplance.h:
#define HPLANCE_MEMOFF 0x8000 /* struct lance_init_block */
#define HPLANCE_NVRAMOFF 0xC008 /* etheraddress as one *nibble* per byte */
The offset of RAM start is 0x8000, the offset of RAM end is 0xC008,
so the RAM size is 16392 bytes.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The order of ram pages is 3, so the ram size is 2^3 * 4K = 32K.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000B, dm9000_msleep() is called during the dm9000_timeout()
routine. Since dm9000_timeout() holds the main spinlock through the
entire routine, mdelay() needs to be used rather than msleep().
Furthermore, the mutex_lock()/mutex_unlock() should be avoided so as to
not sleep with spinlocks held.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the DM9000A/DM9000B force the initial check of the link status. The
DM9000A/B has a link status changed event and this interrupt bit isn't
always set out of reset when a cable is plugged in. This results in the
driver not seeing the cable attached link status until the cable is
removed and plugged in again.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since dm9000_interrupt() is already reading/clearing every set bit in
DM9000_ISR, this additional clear in dm9000_rx() (which is only called
by dm9000_interrupt()) is unnecessary and can be removed.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DM9000 uses level-triggered interrupts. Some systems (PXA270) only
support edge-triggered interrupts on GPIOs. Some changes are necessary
to ensure that interrupts are not triggered while the GPIO interrupt is
masked or we will miss the interrupt forever.
* Make some helper functions called dm9000_mask_interrupts() and
dm9000_unmask_interrupts() for readability.
* dm9000_init_dm9000(): ensure that this function always leaves interrupts
masked regardless of the state when it entered the function. This is
primarily to support the situation in dm9000_open where the logic used
to go:
dm9000_open()
dm9000_init_dm9000()
unmask interrupts
request_irq()
If an interrupt occurred between unmasking the interrupt and
requesting the irq, it would be missed forever as the edge event would
never be seen by the GPIO hardware in the PXA270. This allows us to
change the logic to:
dm9000_open()
dm9000_init_dm9000()
dm9000_mask_interrupts()
request_irq()
dm9000_unmask_interrupts()
* dm9000_timeout(), dm9000_drv_resume(): Add the missing
dm9000_unmask_interrupts() now required by the change above.
* dm9000_shutdown(): Use mask helper function
* dm9000_interrupt(): Use mask/unmask helper functions
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Change a hard-coded 0x3 to NCR_RST | NCR_MAC_LBK in dm9000_reset
* Every single place where dm9000_init_dm9000 was ran, a dm9000_reset
was called immediately before-hand. Bring dm9000_reset into
dm9000_init_dm9000.
* The following commit updated the dm9000_probe reset routine to use NCR_RST
| NCR_MAC_LBK:
6741f40 DM9000B: driver initialization upgrade
and a later commit added a bug-fix to always reset the chip twice:
09ee9f8 dm9000: Implement full reset of DM9000 network device
Unfortunately, since the changes in 6741f40 were made by replacing the
dm9000_probe dm9000_reset with the adjusted iow(), the changes in
09ee9f8 were not incorporated into the dm9000_probe reset.
Furthermore, it bypassed the requisite reset-delay causing some boards
to get at least one "read wrong id ..." dev_err message during
dm9000_probe.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DM9000 supports both active high interrupts and active low interrupts.
This is configured via the attached EEPROM. In the device-tree case, make sure
that the DM9000 driver passes the correct flags to request_irq.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Uninitialzed fields in mailbox command structure
caused commands to time out randomly due to garbage
values so initialize it to zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting David Miller:
"At the moment you call register_netdev() the device is visible, notifications
are sent to userspace, and userland tools can try to bring the interface up
and see the incorrect link state, before you do the netif_carrier_off().
Said another way, between the register_netdev() and netif_carrier_off() call,
userspace can see the device in an inconsistent state."
So call netif_carrier_off() prior to register_netdev().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple more statistics that the hardware offers but aren't part
of the standard netdev stats.
Change-ID: I201db2898f2c284aee3d9631470bc5edd349e9a5
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rx_errors (GLV_REPC) and rx_missed (GLV_RMPC) were removed
from the chip design.
Change-ID: Ifdeb69c90feac64ec95c36d3d32c75e3a06de3b7
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull the PF stat collection out of the VSI collection routine, and
add a unifying stats update routine to call the various stat collection
routines.
Change-ID: I224192455bb3a6e5dc0a426935e67dffc123e306
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change moves some common code in two places into a
small helper function, and corrects a bug in one of the
two places in the process.
Change-ID: If3bba7152b240f13a7881eb0e8a781655fa66ce7
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Structure for VEB context added. Update macro for
transition from ms to GTIME (us) time units.
Change-ID: Ib3a19587b4cf355348655df8f60c6f37bb1497a3
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, the PF driver only notifies the VFs for PF reset events.
Instead, notify the VFs for all types of resets, so they can attempt a
graceful reinit.
Change-ID: I03eb7afde25727198ef620f8b4e78bb667a11370
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i40evf_set_ringparam was broken in several ways. First, it only changed
the size of the first ring, and second, changing the ring size would
often result in a panic because it would change the count before
deallocating resources, causing the driver to either free nonexistent
buffers, or leak leftover buffers.
Fix this by storing the descriptor count in the adapter structure, and
updating the count for each ring each time we allocate them. This
ensures that we always free the right size ring, and always end up with
the requested count when the device is (re)opened.
Change-ID: I298396cd3d452ba8509d9f2d33a93f25868a9a55
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware requires descriptors to be allocated in groups of 32.
Change-ID: I752ccc96769d1bd8d3018c004b8aeff464045bf2
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The driver was allowing the user to set larger size MTU
than the hardware was being configured to support.
The driver was already using VLAN_HLEN when setting the
hardware max receivable frame size, so just add it to the
netdev MTU set entry point as well.
Change-ID: Ie20e2a35d04f8c411253e255bea79ca69aaeaea3
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused defines and macros for RX_LRO.
Change-ID: I8ca6715edfa62b56837417a1c4ff68c2345dab6e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We introduced this check in case this structure changed in the future,
the AQ definition is now mature enough that this check is no longer necessary.
Change-ID: Ic66321d0a08557dc9d8cb84029185352cb534330
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Register range, being subject to register diagnostic, can vary among
different NVMs. We will try to identify the full range and use it for
a register test. This is needed to avoid false test results. If we fail
to define the proper register range we will test only the first register
from that group.
Change-ID: Ieee7173c719733b61d3733177a94dc557eb7b3fd
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A couple of FD checks ended up using bitwise OR to check
a value, which ends up always being evaluated to true.
This should fix the issue. Thanks to DaveJ for noticing
and reporting the issue!
CC: Dave Jones <davej@redhat.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull core irq updates from Thomas Gleixner:
"The irq department delivers:
- Another tree wide update to get rid of the horrible create_irq
interface along with its even more horrible variants. That also
gets rid of the last leftovers of the initial sparse irq hackery.
arch/driver specific changes have been either acked or ignored.
- A fix for the spurious interrupt detection logic with threaded
interrupts.
- A new ARM SoC interrupt controller
- The usual pile of fixes and improvements all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (40 commits)
Documentation: brcmstb-l2: Add Broadcom STB Level-2 interrupt controller binding
irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller
genirq: Improve documentation to match current implementation
ARM: iop13xx: fix msi support with sparse IRQ
genirq: Provide !SMP stub for irq_set_affinity_notifier()
irqchip: armada-370-xp: Move the devicetree binding documentation
irqchip: gic: Use mask field in GICC_IAR
genirq: Remove dynamic_irq mess
ia64: Use irq_init_desc
genirq: Replace dynamic_irq_init/cleanup
genirq: Remove irq_reserve_irq[s]
genirq: Replace reserve_irqs in core code
s390: Avoid call to irq_reserve_irqs()
s390: Remove pointless arch_show_interrupts()
s390: pci: Check return value of alloc_irq_desc() proper
sh: intc: Remove pointless irq_reserve_irqs() invocation
x86, irq: Remove pointless irq_reserve_irqs() call
genirq: Make create/destroy_irq() ia64 private
tile: Use SPARSE_IRQ
tile: pci: Use irq_alloc/free_hwirq()
...
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with CONFIG_DEBUG_SECTION_MISMATCH enabled, the following
WARNING is occured:
LD drivers/net/built-in.o
WARNING: drivers/net/built-in.o(.text+0xcd4c): Section mismatch in
reference from the function gfar_probe() to the function
.init.text:gfar_init_addr_hash_table()
The function gfar_probe() references
the function __init gfar_init_addr_hash_table().
This is often because gfar_probe lacks a __init
annotation or the annotation of gfar_init_addr_hash_table is wrong.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000, igb and ixgbe.
Emil provides his version 2 fix for the detection of SFP+ capable interfaces.
In cases where the driver is loaded while there are no SFP+ modules in cage,
the interface was not being detected as SFP capable. Resolve the issue by
identifying interfaces with no PHY type set as SFP capable which allows the
driver to detect the SFP module when the interface is brought up. In this
version 2 of the patch, the 82599 specific check was removed since we only
have 82598 devices that are SFP capable.
Jacob removes the including of the export header in the ixgbe PTP core, since
it is not needed. Renames igb_ptp_enable() to igb_ptp_feature_enable() to
better reflect the actual functions purpose.
Todd fixes the ethtool loopback test for i354 backplane devices since we
do not know what PHY is to be used for the devices, use MAC loopback for
ethtool tests. Todd also sets the packet buffer size register defaults for
i210 devices.
Yongjian Xu removes the check for skb->len being negative or zero since there
is never a case where it would be zero or negative for e1000.
Manuel Schölling updates e1000 to use the time_after() helper function.
v2: Fix indentation on wrapped line in patch 3 of the series based on
feedback from David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise sparse gives a bunch of warnings like
drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: sparse: incorrect type in argument 4 (different base types)
drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: expected int [signed] gfp
drivers/net/ethernet/mellanox/mlx4/srq.c:110:66: got restricted gfp_t
Signed-off-by: Roland Dreier <roland@purestorage.com>
To be future-proof and for better readability the time comparisons are modified
to use time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no case skb->len would be 0 or 'negative'.
Remove the check.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the defaults on probe for the packet buffer size registers for the
i210.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't know what PHY is to be used for i354 backplane, so use MAC
loopback for ethtool tests.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The name igb_ptp_enable is not synonymous with the purpose of this
function, so rename it to better explain its purpose.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need this header file, so we shouldn't be including it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In cases where the driver is loaded while there are no SFP+ modules in
the cage the interface was not being detected as SFP capable. To account
for this the driver called identify_sfp in ixgbe_get_settings to make
sure the data is correct. However when there is no SFP+ module in the cage
the driver waits for the I2C reads to time out which can take more than a
second and will cause issues with tools (like net-snmp) that may poll
for that information.
This patch resolves the issue by identifying interfaces with no PHY
type set as SFP capable which allows the driver to detect the SFP module
when the interface is brought up. As result of this we can also remove the
identify_sfp call from ixgbe_get_settings.
v2: remove the 82599 specific check since we have 82598 devices that are SFP
capable.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4a55530f38 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support. Add the missing entries using the data
from before that commit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.
This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:
net eth0: Receive FIFO Overflow
Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).
I have tested the RMCR_RNC configuration with NFS root filesystem and
the driver has not failed yet. There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.
There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.
Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rmb() is required to ensure that the CQE is not read before it
is written by the adapter DMA. PCI ordering rules will make sure
the other fields are written before the marker at the end of struct
eth_fast_path_rx_cqe but without rmb() a weakly ordered processor can
process stale data.
Without the barrier we have observed various crashes including
bnx2x_tpa_start being called on queues not stopped (resulting in message
start of bin not in stop) and NULL pointer exceptions from bnx2x_rx_int.
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When injecting EEH error to bnx2x adapter, adapter couldn't be recovery
and caused recursive EEH errors. The patch fixes the issue.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As smsc driver supports carrier detection, it should unset NOCARRIER
flag only after carrier state determination. By default that flag
is off so driver should set it before starting auto-negotiation
Signed-off-by: Balakumaran <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/resource_size.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the hix5hd2 XGMAC 1Gb ethernet device.
The controller requires two queues for tx and two queues for rx.
Controller fetch buffer from free queue and then push to used queue.
Diver should prepare free queue and free buffer from used queue.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iSCSI netlink message needs to be sent before the ulp_ops is cleared
as it is sent through a function pointer in the ulp_ops. This bug
causes iscsid to not get the message when the bnx2i driver is unloaded.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are allocating memory with GFP_KERNEL under spinlock. Since this is
the only call manipulating the cnic_udev_list and it is always under
rtnl_lock, cnic_dev_lock can be safely removed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the called function, such as bnx2fc_indicate_netevent(), can sleep,
we cannot take rcu_lock(). To prevent the rcu protected ulp_ops from going
away, we use the cnic_lock mutex and set the ULP_F_CALL_PENDING flag.
The code already waits for ULP_F_CALL_PENDING flag to clear in
cnic_unregister_device().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit cd11cf5053 I accidentally
added an error message. I used it for debugging and forgot to remove
it before submitting the patch.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
Pull request: Fixes for new ethtool RSS commands
This addresses several problems I previously identified with the new
ETHTOOL_{G,S}RSSH commands:
1. Missing validation of reserved parameters
2. Vague documentation
3. Use of unnamed magic number
4. No consolidation with existing driver operations
I don't currently have access to suitable network hardware, but have
tested these changes with a dummy driver that can support various
combinations of operations and sizes, together with (a) Debian's ethtool
3.13 (b) ethtool 3.14 with the submitted patch to use ETHTOOL_{G,S}RSSH
and minor adjustment for fixes 1 and 3.
v2: Update RSS operations in vmxnet3 too
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_{G,S}RXFHINDIR and ETHTOOL_{G,S}RSSH should work for drivers
regardless of whether they expose the hash key, unless you try to
set a hash key for a driver that doesn't expose it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 5bbde4d2ec ("net: fec: use pinctrl PM helpers") caused the following
build error on m68k:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_open':
drivers/net/ethernet/freescale/fec_main.c:1819:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_close':
drivers/net/ethernet/freescale/fec_main.c:1863:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
In order to fix the build error, include the linux/pinctrl/consumer.h header
file.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ec_bhf driver is specific to the Beckhoff CX embedded PC series.
These are based on Intel x86 CPU. So we can add a dependency on
X86, with COMPILE_TEST as an alternative to still allow for broader
build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Darek Marcinkiewicz <reksio@newterm.pl>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix:
CC drivers/net/ethernet/broadcom/bcmsysport.o
In file included from drivers/net/ethernet/broadcom/bcmsysport.c:28:0:
drivers/net/ethernet/broadcom/bcmsysport.h:41:8: error: redefinition of 'struct tsb'
arch/sparc/include/asm/mmu_64.h:65:8: note: originally defined here
make[1]: *** [drivers/net/ethernet/broadcom/bcmsysport.o] Error 1
we change struct tsb to struct bcm_tsb in the broadcom driver in
order to avoid the namespace collision. For consistency, we also
change struct rsb to struct bcm_rsb, so the Rx/Tx symmetry is
maintained.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding proper stop/wake thresholds, we can expect a queue to never
be full and drop the NETDEV_TX_BUSY return path. In any case, if the queue
cannot accommodate a TSO packet, the packet would be discarded.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the current dropped packet count by doing it properly,
increasing the count when a packet is discarded; i.e. the packet is not
processed and the driver returns NETDEV_TX_OK.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This is true only for the last fragment of the packet.
This is wrong, however, since every descriptor buffer is DMA mapped and needs
to be unmapped.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive. Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The following patch moved device tree interrupt resolution into
platform_get_irq_byname:
ad69674 of/irq: do irq resolution in platform_get_irq_byname()
As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:
http://lists.linaro.org/pipermail/kernel-build-reports/2014-May/003659.html
This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the enic driver to make use of __dev_uc_sync and
__dev_mc_sync calls. Previously the driver was doing its own list
management by storing the mc_addr and uc_addr list in a 32 address array.
With this change the sync data is stored in the netdev_addr_list structures
and instead we just track how many addresses we have written to the device.
When we encounter 32 we stop and print a message as occurred previously with
the old approach.
Other than the core change the only other bit needed was to propagate the
constant attribute with the MAC address as there were several spots where
is twas only passed as a u8 * instead of a const u8 *.
This patch is meant to maintain the original functionality without the use
of the mc_addr and uc_addr arrays.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.
commit cab6715c3e
Author: Yang Wei <Wei.Yang@windriver.com>
Date: Sun May 25 09:53:44 2014 +0800
net: driver: stmicro: Remove some useless the lock protection
This introduced the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
context imbalance in 'stmmac_get_pauseparam' -
different lock contexts for basic block
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 70a640d0da
("net/mlx4_en: Use affinity hint") and commit
c8865b64b0 ("cpumask: Utility function
to set n'th cpu - local cpu first") because these changes break
the build when SMP is disabled amongst other things.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't be using regulator_get_optional() here. These
regulators are always present as part of the physical design and
there isn't any way to use an internal regulator or change the
source of the reference voltage via software. Given that the only
users of this driver in the kernel are DT based, this change
should be transparent to them even if they don't specify any
supplies because the regulator framework will insert dummy
supplies as needed.
Cc: Nishanth Menon <nm@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and i40evf.
Kevin updates the i40e and i40evf driver i40e_check_asq_alive() to ensure
the length register offset is non-zero which indicates that the software
has initialized the admin queue. Also removes PCTYPE definitions which are
now reserved.
Mitch enables descriptor prefetch for rings belonging to the virtual function.
Also configures the VF minimum transmit rate to 50 Mbps rather than 0 which was
be interpreted as no limit at all. Mitch found in order for the VF to achieve
its programmed transmit rate, we need to set the max credit value to 4.
Lastly fixes a Tx hang and firmware crash that happens after setting the MTU
on a VF by not using the RESETTING state during reinit, this is because
the RESETTING state means that a catastrophic hardware bad thing is happening
and the driver needs to tiptoe around and not use the admin queue or registers.
A reinit is no big deal and we can use the admin queue (and we should) so
do not set the state to RESETTING during reinit to resolve the bug.
Akeem changes the declaration of the transmit and receive rings inside
several loops to eliminate declaring the same ring every time for the
duration of the loop and declares them just once before the loop. Also fixes
the driver to clear the recovery pending bit if pf_reset fails instead of
falling through the setup process.
Anjali makes a change based on feedback from Ben Hutchings that cmd->data
needs to be reported in ETHTOOL_GRXCLSRLCNT and use a helper function to
calculate the total filter count.
Jesse removes storm control since the storm control features are not apart
of the hardware and were mistakenly left in the code.
Greg changes tx_lpi_status and rx_lpi_status from bool to u32 to avoid
sparse errors.
Shannon adds the clear_pxe AdminQ API call to tell the firmware that the
driver is taking over from PXE. In addition, relaxes the firmware API
check to allow more flexibility in handling newer NICs and NVMs in the field.
Vasu ensures that FCoE is disabled for MFP modes since it is not supported
by overriding the hardware FCoE capability.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
