Hardware does not have a way of telling a PF how much of the global
shared FD table space is still available or is consumed.
Previously, every PF but PF0 would think there was still space available
when there wasn't. The PFs would continue to try to add filters and fail.
With this new logic if a filter programming error is detected we just
check if we are close to the guaranteed space full and that can be used
as a hint to say, there might not be space and we should turn off the
features. This way we can turn off the feature in SW for all PFs in
time.
Change-ID: I725cb2fab16c033f883056362b4542c1400503c5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There wasn't a need to play the logic twice, it seems
like a left over from when we had to add two PTYPEs for
one filter. There should be no change in the number of
filters that actually got added to the hardware.
Change-ID: I5071d02eafd020b60e30eb96219f110f334eec85
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently every time we run through the i40e_ptp_init routine, we create
a new device node. This function is called by i40e_reset_and_rebuild
which is used to handle reset of the device. Even though the 1588
registers only get cleared on a GLOBAL reset, this function is still
called to handle a CORE reset.
This causes a leak of PTP device nodes at every reset. To fix this,
break PTP device clock node creation out of i40e_ptp_init, and only call
this if we don't already have a device created. Further invocation of
i40e_ptp_init will not generate new PTP devices. Instead, only the
necessary work required to reconfigure 1588 will be done.
This change also fixes an issue where a reset can cause the
device to forget it's timestamp configuration, and revert to the default
mode.
Change-ID: I741d01c61d9fe1d24887859d1316e1a8a892909e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the SIOCGHWTSTAMP ioctl from possibly returning bad
data, by not permanently storing the setting into the private
structure until after we've finished validating that we can support it.
Change-ID: Ib59f9b4f73f451d5a2e76fb8efa5d4271b218433
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch facilitates future work by breaking the PTP hardware control
bits out of the i40e_set_ts_config function. By doing this, we can
maintain state about the 1588 timestamping mode and properly re-enable
to the last known mode during a re-initialize of 1588 bits.
This patch also modifies i40e_ptp_init to call the
i40e_ptp_set_timestamp_mode during the reconfiguration process. A
future patch will ensure that the hwtstamp_config structure is not reset
during this process, so that timestamp mode will be maintained across a
reset.
Change-ID: Ic20832c96c5c512ac203b6c7534e10d891c560f0
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduces possible confusion and ambiguity in purpose of the ancillary
feature control entry point function.
Change-ID: I21d773c1a86878f6d061505185b596c788d1b7cc
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes the firmware will not indicate an error but fail to pass a
message between the VF and the PF driver. If this happens, just resend
the request.
This fixes an initialization failure if many VFs are instantiated at the
same time and the VF module is autoloaded.
Change-ID: Idd1ad8da2fd5137859244685c355941427d317d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct a missing word in a log message.
Change-ID: Id94da7d9f842382d073b3947e0b616503e2f8e91
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When verifying the API version (which is the first time the driver
communicates with the firmware and thus the PF driver), there are many
ways in which a failure can occur. There may be an error from the
firmware, there may be unresponsive firmware, there may be an error from
the PF driver, etc, etc.
Make this function return more useful information, instead of just -EIO.
Propagate FW errors back to the caller, and log a message if the PF
sends an invalid reply.
Change-ID: I3e9135a2b80f7acdb855f62f12b2b2668c9a8951
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver fails to complete early init, then rmmod can cause a
softlock when the driver tries to stop a watchdog timer that never even
got initialized.
Add a check to see if the timer is actually initialized before stopping
it.
Change-ID: Id9d550aa8838e07f4b02afe7bc017ef983779efc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix HMC handling for big endian architectures.
Change-ID: Id8c46fc341815d47bfe0af8b819f0ab9a1e9e515
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We do not need to acquire NVM for Shadow RAM XSUM calculation, as we only
read from SR through SRCTL register for which having the ownership is not
required.
Change-ID: Ie238a8f09917d1d25f24cc7cec271951ac7b98f2
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If CONFIG_RFS_ACCEL=n:
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_open':
drivers/net/ethernet/cisco/enic/enic_main.c:1603:2: error: implicit declaration of function 'enic_rfs_flw_tbl_init' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_stop':
drivers/net/ethernet/cisco/enic/enic_main.c:1630:2: error: implicit declaration of function 'enic_rfs_flw_tbl_free' [-Werror=implicit-function-declaration]
Introduced in commit a145df23ef ("enic: Add
Accelerated RFS support").
Dummy functions are provided, but their prototypes are missing, causing the
build failure. Provide dummy static inline functions instead to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-24
This series contains updates to i40e and i40evf.
Greg provides a patch to stop the VF device after setting its MAC address.
This is due to if the host VMM administrator has changed the VF device's MAC
address then the i40e driver needs to halt the VF device so that the
administrator will be forced to reload the VF driver so that the VF driver
will start using the newly assigned MAC address.
Shannon provides several patches for i40e, first makes prep_for_test() a
void function since the return value was being ignored for the most part
by all its callers. Adds a log warning when the firmware's API minor/major
number is not what we expect to assist the user by informing them they
may need to update their NVM or SW. Cleans up a stray print message
so that it is similar to other print messages. Ensures to set the
WoL flag when setting LAA and allow the user to set LAA again. So do
not short-circuit the LAA assignment when the driver thinks it has
already been done as it is possible that the user might want to force
the address setting again. Provides a couple more LAA fixes to ensure
the LAA gets restored after resets.
Neerav provides a patch for i40e to add a PF reset when a malicious driver
event for the PF occurs. As per the specification when the PF driver
receives a malicious driver event the queue that caused the event is
already stopped and it is expected that the function that owns the queue
will reset the queue, but in some cases it may not be possible to determine
the queue, so it is suggested to reset the whole function.
Carolyn fixes ethtool coalesce settings to allow 0 as a disable value and
adds message to user about invalid values.
Jesse removes a reserved type which was not removed from the code.
Catherine provides a patch to add the ability to enable/disable link from
set_link)restart_an() which will make it easy to toggle link without
calling set_phy_config() when no other link settings need to change.
Anjali provides a patch to ensure we do a PF reset on Tx hang and that
way we avoid any Malicious Driver Detect (MDD) events because of a Tx
queue disable failure.
v2:
- fixed the un-needed return in patch 2 based on feedback from Sergei Shtylyov
- added punctuation to print statements and code comment based on
feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David S. Miller <davem@davemloft.net>
o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands cnic driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>
o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands bnx2 driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3f85944fe2 ("net: Add sysfs file
for port number") introduce dev_port to network devices. cxgb4 adapters
have multiple ports on the same PCI function, and used dev_id to
identify those ports. That use was removed by commit
8c367fcbe6 ("cxgb4: Do not set
net_device::dev_id to VI index"), since dev_id should be used only when
devices share the same MAC address.
Using dev_port for cxgb4 allows different ports on the same PCI function
to be identified.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 506724c463 "tg3: Override clock,
link aware and link idle mode during NVRAM dump" changed the timeout
value for nvram command execution from 100ms to 1ms. But the 1ms
timeout value was only sufficient for nvram read operations but not
write operations for most of the devices supported by tg3 driver.
This patch sets the MAX to 50ms. Also it uses usleep_range instead
of udelay.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a Tx hang happens, usually the Tx queue disable fails. At
this point if we try to recover by a VSI reinit the HW gets
unhappy and we get a Malicious Driver Detect (MDD) event.
HW expects a PF reset if a queue disable fails, if we don't do a PF
reset and restart the queue we get an MDD. This patch makes sure we
do a PF reset on Tx hang and that way we avoid any MDD because of Tx
queue disable failure.
Change-ID: I665ab6223577c788da857ee2132e733dc9a451e4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF reset to clean up at the end of the remove is a nice thing
to do, but it also removes any LAA setting that Wake On LAN wants
for future wake up.
Change-ID: Ic090ec714df2d722281d11735cf75f2aa4432e2c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LAA is lost on a reset, so be sure to replay it when rebuilding
the switch after any reset.
Change-ID: I6e643f9a59dfd899b6cbdf84d93b4bc9c37bb949
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't short-circuit the LAA assignment when the driver thinks it has
already been done - it is possible that the user might want to force
the address setting again. At the same time, this requires a little
re-ordering of the filter management.
Change-ID: Ia0d71e3bc04edd7b68cf67edecc00abe7b9f6639
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the Firmware sets up the LAA as a Wake-On-LAN address.
Change-ID: I57b9acd8c288424fcfed0911053eb725c400b41c
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ability is already there in the fw and this will make it easy
to toggle link without calling set_phy_config when no other link
settings need to change.
Change-ID: I185567ae81776382ac145247e4eb1ee95f22382c
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the PCTYPES that was moved to a reserved value
wasn't removed from the code.
Change-ID: I31fafe6d79c5f5128179979af5eaafa8c0cd62fe
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the i40e_set_coalesce function to allow 0 as a disable
value. Also, added message to user about invalid value and provides valid
range.
Change-ID: I6c9ff11a9861f2045bd543745a3d132999ffbbd8
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This log print message will probably never be seen, but it needs to match
the "attempting to rebuild switch\n" log message a few lines above.
Change-ID: Ic3f5b4f67568d721cb02e826cf2cb33847f51c11
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the firmware's API minor number is larger than the one expected, log
a warning and recommend driver SW update.
If the firmware's API major or minor number is smaller then the one expected
(n for major, n or n-1 for minor), log a warning and recommend NVM update.
Change-ID: If0b887e055478f8e435ba7fa28113b63a6f1bb35
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As per the spec when the PF driver receives a Malicious driver event
the queue that caused the event is already stopped and it is expected
that the function that owns the queue will reset the queue.
In some cases it may not be possible to determine the queue and it is
suggested to reset the whole function.
This patch takes the later approach when the event is owned by the PF
that owns it.
Change-ID: I40f9764a6a5e068c0ef8438db00c5aa9c2c6c1c8
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The return from i40e_prep_for_reset() was being ignored by almost all
its callers. The one place it wasn't ignored could have caused a silent
and confusing failure of the driver to finish a reset. Since we really
are doing a rebuild anyway, ignore this last case as well and simply
make the function a void type.
Change-ID: Ia4fed7f903d39a6c47c5722625a53e59c3f7ed53
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the host VMM administrator has changed the VF device's MAC address then
the i40e driver needs to halt the VF device so that the administrator will
be forced to reload the VF driver. This will cause the VF driver to start
using the newly assigned MAC address. This brings the i40e driver into
conformance with operational characteristics of other Intel SR-IOV
featured drivers.
Change-ID: Ic7242cceb8287dd2cb72fb1f3166a032a28bf88a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hi,
This patch fixes warnings generated by sparse as pointed out by kbuild test
robot, please apply to net-next. Applies on top of
commit 79631c89ed ("trivial: net/irda/irlmp.c:
Fix closing brace followed by if")
-Anish
v2: cleanup submission as per davem's feedback
Fixes: 76bcb31efc ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver (on PF or VF) needs to detect if the function is in qnq mode for
a HW hack in be_rx_compl_get() to work.
The driver queries this information using the GET_PROFILE_CONFIG cmd
(since the commit below can caused this regression.) But this cmd is not
available on VFs and so the VFs fail to detect qnq mode. This causes
vlan traffic to not work.
The fix is to use the the adapter->function_mode value queried via
QUERY_FIRMWARE_CONFIG cmd on both PFs and VFs to detect the qnq mode.
Also QNQ_MODE was incorrectly named FLEX10_MODE; correcting that too as the
fix reads much better with the name change.
Fixes: f93f160b5 ("refactor multi-channel config code for Skyhawk-R chip")
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Till now enic had been doing tx clean in isr.
Using napi infrastructure to move the tx clean up out of isr to softirq.
Now, wq isr schedules napi poll. In enic_poll_msix_wq we clean up the tx queus.
This is applicable only on MSIX. In INTx and MSI we use single napi to clean
both rx & tx queues.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for low latency busy_poll.
* Introduce drivers ndo_busy_poll function enic_busy_poll, which is called by
socket waiting for data.
* Introduce locking between napi_poll nad busy_poll
* enic_busy_poll cleans up all the rx pkts possible. While in busy_poll, rq
holds the state ENIC_POLL_STATE_POLL. While in napi_poll, rq holds the state
ENIC_POLL_STATE_NAPI.
* in napi_poll we return if we are in busy_poll. Incase of INTx & msix, we just
service wq and return if busy_poll is going on.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were experiencing occasional "BUG: scheduling while atomic" splats
in our testing. Enabling DEBUG_SPINLOCK and DEBUG_LOCKDEP in the kernel
exposed a lockdep in the enic driver.
enic 0000:0b:00.0 eth2: Link UP
======================================================
[ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ]
3.12.0-rc1.x86_64-dbg+ #2 Tainted: GF W
------------------------------------------------------
NetworkManager/4209 [HC0[0]:SC0[2]:HE1:SE0] is trying to acquire:
(&(&enic->devcmd_lock)->rlock){+.+...}, at: [<ffffffffa026b7e4>] enic_dev_packet_filter+0x44/0x90 [enic]
The fix was to replace spin_lock with spin_lock_bh for the enic
devcmd_lock, so that soft irqs would be disabled while the lock
is held.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds supports for Accelerated Receive Flow Steering.
When the desired rx is different from current rq, for a flow, kernel calls the
driver function enic_rx_flow_steer(). enic_rx_flow_steer adds a IP-TCP/UDP
hardware filter.
Driver registers a timer function enic_flow_may_expire. This function is called
every HZ/4 seconds. In this function we check if the added filter has expired
by calling rps_may_expire_flow(). If the flow has expired, it removes the hw
filter.
As of now adaptor supports only IPv4 - TCP/UDP filters.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_cpu_rmap provides the reverse irq cpu affinity. This patch allocates and
sets drivers netdev->rx_cpu_rmap accordingly.
rx_cpu_rmap is set in enic_request_intr() which is called by enic_open and
rx_cpu_rmap is freed in enic_free_intr() which is called by enic_stop.
This is used by Accelerated RFS.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds interface to add and delete IP 5 tuple filter. This interface
is used by Accelerated RFS code to steer a flow to corresponding receive
queue.
As of now adaptor supports only ipv4 + tcp/udp packet steering.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware (in readq(&devcmd->args[0])) returns positive number in case of error.
But _vnic_dev_cmd should return a negative value in case of error.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
