One helpful feature to help debug the Header Parser TCAM filter in PPv2
is to be able to see if the entries did match something when a packet
comes in. This can be done by using the built-in hit counter for TCAM
entries.
This commit implements reading the counter, and exposing its value on
debugfs for each filter entry.
The counter is a 16-bits clear-on-read value, located at:
.../mvpp2/<controller>/parser/XXX/hits
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 Packer Header Parser has a TCAM based filter, that is not
trivial to configure and debug. Being able to dump TCAM entries from
userspace can be really helpful to help development of new features
and debug existing ones.
This commit adds a basic debugfs interface for the PPv2 driver, focusing
on TCAM related features.
<mnt>/mvpp2/ --- f2000000.ethernet
\- f4000000.ethernet --- parser --- 000 ...
| \- 001
| \- ...
| \- 255 --- ai
| \- header_data
| \- lookup_id
| \- sram
| \- valid
\- eth1 ...
\- eth2 --- mac_filter
\- parser_entries
\- vid_filter
There's one directory per PPv2 instance, named after pdev->name to make
sure names are uniques. In each of these directories, there's :
- one directory per interface on the controller, each containing :
- "mac_filter", which lists all filtered addresses for this port
(based on TCAM, not on the kernel's uc / mc lists)
- "parser_entries", which lists the indices of all valid TCAM
entries that have this port in their port map
- "vid_filter", which lists the vids allowed on this port, based on
TCAM
- one "parser" directory (the parser is common to all ports), containing :
- one directory per TCAM entry (256 of them, from 0 to 255), each
containing :
- "ai" : Contains the 1 byte Additional Info field from TCAM, and
- "header_data" : Contains the 8 bytes Header Data extracted from
the packet
- "lookup_id" : Contains the 4 bits LU_ID
- "sram" : contains the raw SRAM data, which is the result of the TCAM
lookup. This readonly at the moment.
- "valid" : Indicates if the entry is valid of not.
All entries are read-only, and everything is output in hex form.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the appropriate SPDX license identifiers and drop the license text.
This patch is only cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-07-15
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Various different arm32 JIT improvements in order to optimize code emission
and make the JIT code itself more robust, from Russell.
2) Support simultaneous driver and offloaded XDP in order to allow for advanced
use-cases where some work is offloaded to the NIC and some to the host. Also
add ability for bpftool to load programs and maps beyond just the cgroup case,
from Jakub.
3) Add BPF JIT support in nfp for multiplication as well as division. For the
latter in particular, it uses the reciprocal algorithm to emulate it, from Jiong.
4) Add BTF pretty print functionality to bpftool in plain and JSON output
format, from Okash.
5) Add build and installation to the BPF helper man page into bpftool, from Quentin.
6) Add a TCP BPF callback for listening sockets which is triggered right after
the socket transitions to TCP_LISTEN state, from Andrey.
7) Add a new cgroup tree command to bpftool which iterates over the whole cgroup
tree and prints all attached programs, from Roman.
8) Improve xdp_redirect_cpu sample to support parsing of double VLAN tagged
packets, from Jesper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Ignatov says:
====================
This patchset adds TCP-BPF callback for listening sockets.
Patch 0001 provides more details and is the main patch in the set.
Patch 0006 adds selftest for the new callback.
Other patches are bug fixes and improvements in TCP-BPF selftest
to make it easier to extend in 0006.
====================
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cover new TCP-BPF callback in test_tcpbpf: when listen() is called on
socket, set BPF_SOCK_OPS_STATE_CB_FLAG so that BPF_SOCK_OPS_STATE_CB
callback can be called on future state transition, and when such a
transition happens (TCP_LISTEN -> TCP_CLOSE), track it in the map and
verify it in user space later.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reduce amount of copy/paste for debug info when result is verified in
the test and keep that info together with values being checked so that
they won't get out of sync.
It also improves debug experience: instead of checking manually what
doesn't match in debug output for all fields, only unexpected field is
printed.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Switch to cgroup_helpers to simplify the code and fix cgroup cleanup:
before cgroup was not cleaned up after the test.
It also removes SYSTEM macro, that only printed error, but didn't
terminate the test.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add new TCP-BPF callback that is called on listen(2) right after socket
transition to TCP_LISTEN state.
It fills the gap for listening sockets in TCP-BPF. For example BPF
program can set BPF_SOCK_OPS_STATE_CB_FLAG when socket becomes listening
and track later transition from TCP_LISTEN to TCP_CLOSE with
BPF_SOCK_OPS_STATE_CB callback.
Before there was no way to do it with TCP-BPF and other options were
much harder to work with. E.g. socket state tracking can be done with
tracepoints (either raw or regular) but they can't be attached to cgroup
and their lifetime has to be managed separately.
Signed-off-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Ido Schimmel says:
====================
mlxsw: Add VRRP support
When a router that is acting as the default gateway of a host stops
functioning, the host will encounter packet loss until the router starts
functioning again.
To increase the reliability of the default gateway without performing
reconfiguration on the host, a host can use a Virtual Router Redundancy
Protocol (VRRP) Router. This virtual router is composed from several
routers where only one is actually forwarding packets from the host (the
master router) while the other routers act as backup routers. The
election of the master router is determined by the VRRP protocol [1].
Packets addressed to the virtual router are always sent to the virtual
router MAC address (IPv4: 00-00-5E-00-01-XX, IPv6: 00-00-5E-00-02-XX).
Such packets can only be accepted by the master router and must be
discarded by the backup routers.
In Linux, VRRP is usually implemented by configuring a macvlan with the
virtual router MAC on top of the router interface that is connected to
the host / LAN. The macvlan on the master router is assigned the virtual
IP (VIP) that the host uses as its gateway.
In order to support VRRP in mlxsw, we first need to enable macvlan upper
devices on top of mlxsw netdevs and their uppers. This is done by the
first patch, which also takes care of sanitizing macvlan configurations
that are not currently supported by the driver.
The second patch directs packets with destination MAC addresses as the
macvlans to the router so that they will undergo an L3 lookup. This is
consistent with the kernel's behavior where the macvlan's Rx handler
will re-inject such packets to the Rx path so that they will be picked
up by the IPvX protocol handlers and undergo an L3 lookup. Note that the
driver prevents the macvlans from being enslaved to other devices, to
ensure the packets will be picked up by the protocol handler and not by
another Rx handler.
The third patch adds packet traps for VRRP control packets for both IPv4
and IPv6. Finally, the last patch optimizes the reception of VRRP MACs
by potentially skipping one L2 lookup for them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hosts using a VRRP router send their packets with a destination MAC of
the VRRP router which is of the following form [1]:
IPv4 - 00-00-5E-00-01-{VRID}
IPv6 - 00-00-5E-00-02-{VRID}
Where VRID is the ID of the virtual router. Such packets are directed to
the router block in the ASIC by an FDB entry that was added in the
previous patch.
However, in certain cases it is possible to skip this FDB lookup and
send such packets directly to the router. This is accomplished by adding
these special MAC addresses to the RIF cache. If the cache is hit, the
packet will skip the L2 lookup and ingress the router with the RIF
specified in the cache entry.
1. https://tools.ietf.org/html/rfc5798#section-7.3
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Virtual Router Redundancy Protocol packets are used to communicate the
state of the Master router associated with the virtual router ID (VRID).
These are link-local multicast packets sent with IP protocol 112 that
are trapped in the router block in the ASIC.
Add a trap for these packets and mark the trapped packets to prevent
them from potentially being re-flooded by the bridge driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IP packet received on a netdev with a macvlan upper whose MAC matches
the packet's destination MAC will be re-injected to the Rx path as if it
was received by the macvlan, and perform an L3 lookup.
Reflect this functionality to the ASIC by programming FDB entries that
will direct MACs of macvlan uppers to the router.
In a similar fashion to router interfaces (RIFs) that are programmed
upon the addition of the first IP address on an interface and destroyed
upon the removal of the last IP address, the FDB entries for the macvlan
are added and destroyed based on the addition of the first and removal
of the last IP address on the macvlan.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow more unicast MAC addresses (e.g., VRRP virtual MAC) to
be directed to the router we need to enable macvlan uppers on top of
mlxsw netdevs.
Allow macvlan upper devices on top of mlxsw netdevs and sanitize
configurations that can't work. For example, a macvlan can't be enslaved
to a bridge as without ACLs the device doesn't take the destination MAC
into account when classifying a packet to a bridge instance (i.e., a
FID).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_rcv_nxt_update() is already executed in tcp_data_queue().
This line is redundant.
See bellow,
tcp_queue_rcv
tcp_rcv_nxt_update(tcp_sk(sk), TCP_SKB_CB(skb)->end_seq);
tcp_rcv_nxt_update(tp, TCP_SKB_CB(skb)->end_seq); <<<< redundant
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch augments the output of bpftool's map dump and map lookup
commands to print data along side btf info, if the correspondin btf
info is available. The outputs for each of map dump and map lookup
commands are augmented in two ways:
1. when neither of -j and -p are supplied, btf-ful map data is printed
whose aim is human readability. This means no commitments for json- or
backward- compatibility.
2. when either -j or -p are supplied, a new json object named
"formatted" is added for each key-value pair. This object contains the
same data as the key-value pair, but with btf info. "formatted" object
promises json- and backward- compatibility. Below is a sample output.
$ bpftool map dump -p id 8
[{
"key": ["0x0f","0x00","0x00","0x00"
],
"value": ["0x03", "0x00", "0x00", "0x00", ...
],
"formatted": {
"key": 15,
"value": {
"int_field": 3,
...
}
}
}
]
This patch calls btf_dumper introduced in previous patch to accomplish
the above. Indeed, btf-ful info is only displayed if btf data for the
given map is available. Otherwise existing output is displayed as-is.
Signed-off-by: Okash Khawaja <osk@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This consumes functionality exported in the previous patch. It does the
main job of printing with BTF data. This is used in the following patch
to provide a more readable output of a map's dump. It relies on
json_writer to do json printing. Below is sample output where map keys
are ints and values are of type struct A:
typedef int int_type;
enum E {
E0,
E1,
};
struct B {
int x;
int y;
};
struct A {
int m;
unsigned long long n;
char o;
int p[8];
int q[4][8];
enum E r;
void *s;
struct B t;
const int u;
int_type v;
unsigned int w1: 3;
unsigned int w2: 3;
};
$ sudo bpftool map dump id 14
[{
"key": 0,
"value": {
"m": 1,
"n": 2,
"o": "c",
"p": [15,16,17,18,15,16,17,18
],
"q": [[25,26,27,28,25,26,27,28
],[35,36,37,38,35,36,37,38
],[45,46,47,48,45,46,47,48
],[55,56,57,58,55,56,57,58
]
],
"r": 1,
"s": 0x7ffd80531cf8,
"t": {
"x": 5,
"y": 10
},
"u": 100,
"v": 20,
"w1": 0x7,
"w2": 0x3
}
}
]
This patch uses json's {} and [] to imply struct/union and array. More
explicit information can be added later. For example, a command line
option can be introduced to print whether a key or value is struct
or union, name of a struct etc. This will however come at the expense
of duplicating info when, for example, printing an array of structs.
enums are printed as ints without their names.
Signed-off-by: Okash Khawaja <osk@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch introduces btf__resolve_type() function and exports two
existing functions from libbpf. btf__resolve_type follows modifier
types like const and typedef until it hits a type which actually takes
up memory, and then returns it. This function follows similar pattern
to btf__resolve_size but instead of computing size, it just returns
the type.
These functions will be used in the followig patch which parses
information inside array of `struct btf_type *`. btf_name_by_offset is
used for printing variable names.
Signed-off-by: Okash Khawaja <osk@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
perf propagates its feature check results to libbpf. This means
features for which perf probes must be a superset of libbpf's
required features. perf depends on FEATURE_TESTS_BASIC for its list
of features.
commit 531b014e7a ("tools: bpf: make use of reallocarray") added
reallocarray use to libbpf, make perf also perform the reallocarray
feature check.
Fixes: 531b014e7a ("tools: bpf: make use of reallocarray")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Fixes: f9358e12a0 ("net: mvpp2: split ingress traffic into multiple flows")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By a simple extension of of_phy_get_and_connect() drivers
that have a fixed link on e.g. RGMII can support also
fixed links, so in addition to:
ethernet-port {
phy-mode = "rgmii";
phy-handle = <&foo>;
};
This setup with a fixed-link node and no phy-handle will
now also work just fine:
ethernet-port {
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
pause;
};
};
This is very helpful for connecting random ethernet ports
to e.g. DSA switches that typically reside on fixed links.
The phy-mode is still there as the fixes link in this case
is still an RGMII link.
Tested on the Cortina Gemini driver with the Vitesse DSA
router chip on a fixed 1Gbit link.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend struct tcf_walker with additional 'cookie' field. It is intended to
be used by classifier walk implementations to continue iteration directly
from particular filter, instead of iterating 'skip' number of times.
Change flower walk implementation to save filter handle in 'cookie'. Each
time flower walk is called, it looks up filter with saved handle directly
with idr, instead of iterating over filter linked list 'skip' number of
times. This change improves complexity of dumping flower classifier from
quadratic to linearithmic. (assuming idr lookup has logarithmic complexity)
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reported-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
People noticed that the code match on IEEE 802.1ad (ETH_P_8021AD) ethertype,
and this implies Q-in-Q or double tagged VLANs. Thus, we better parse
the next VLAN header too. It is even marked as a TODO.
This is relevant for real world use-cases, as XDP cpumap redirect can be
used when the NIC RSS hashing is broken. E.g. the ixgbe driver HW cannot
handle double tagged VLAN packets, and places everything into a single
RX queue. Using cpumap redirect, users can redistribute traffic across
CPUs to solve this, which is faster than the network stacks RPS solution.
It is left as an exerise how to distribute the packets across CPUs. It
would be convenient to use the RX hash, but that is not _yet_ exposed
to XDP programs. For now, users can code their own hash, as I've demonstrated
in the Suricata code (where Q-in-Q is handled correctly).
Reported-by: Florian Maury <florian.maury-cv@x-cli.eu>
Reported-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This patch adds support for IGMPMSG_WRVIFWHOLE which is used to pass
full packet and real vif id when the incoming interface is wrong.
While the RP and FHR are setting up state we need to be sending the
registers encapsulated with all the data inside otherwise we lose it.
The RP then decapsulates it and forwards it to the interested parties.
Currently with WRONGVIF we can only be sending empty register packets
and will lose that data.
This behaviour can be enabled by using MRT_PIM with
val == IGMPMSG_WRVIFWHOLE. This doesn't prevent IGMPMSG_WRONGVIF from
happening, it happens in addition to it, also it is controlled by the same
throttling parameters as WRONGVIF (i.e. 1 packet per 3 seconds currently).
Both messages are generated to keep backwards compatibily and avoid
breaking someone who was enabling MRT_PIM with val == 4, since any
positive val is accepted and treated the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
This set is adding support for loading driver and offload XDP
at the same time. This enables advanced use cases where some
of the work is offloaded to the NIC and some is done by the host.
Separate netlink attributes are added for each mode of operation.
Driver callbacks for offload are cleaned up a little, including
removal of .prog_attached flag.
====================
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Split handling of offloaded and driver programs completely. Since
offloaded programs always come with XDP_FLAGS_HW_MODE set in reality
there could be no sharing, anyway, programs would only be installed
in driver or in hardware. Splitting the handling allows us to install
programs in HW and in driver at the same time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add tests for having an XDP program attached in the driver and
another one attached in HW simultaneously.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Allow netdevsim to accept driver and offload attachment of XDP
BPF programs at the same time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Split the query of HW-attached program from the software one.
Introduce new .ndo_bpf command to query HW-attached program.
This will allow drivers to install different programs in HW
and SW at the same time. Netlink can now also carry multiple
programs on dump (in which case mode will be set to
XDP_ATTACHED_MULTI and user has to check per-attachment point
attributes, IFLA_XDP_PROG_ID will not be present). We reuse
IFLA_XDP_PROG_ID skb space for second mode, so rtnl_xdp_size()
doesn't need to be updated.
Note that the installation side is still not there, since all
drivers currently reject installing more than one program at
the time.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Basic operations drivers perform during xdp setup and query can
be moved to helpers in the core. Encapsulate program and flags
into a structure and add helpers. Note that the structure is
intended as the "main" program information source in the driver.
Most drivers will additionally place the program pointer in their
fast path or ring structures.
The helpers don't have a huge impact now, but they will
decrease the code duplication when programs can be installed
in HW and driver at the same time. Encapsulating the basic
operations in helpers will hopefully also reduce the number
of changes to drivers which adopt them.
Helpers could really be static inline, but they depend on
definition of struct netdev_bpf which means they'd have
to be placed in netdevice.h, an already 4500 line header.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
In preparation for support of simultaneous driver and hardware XDP
support add per-mode attributes. The catch-all IFLA_XDP_PROG_ID
will still be reported, but user space can now also access the
program ID in a new IFLA_XDP_<mode>_PROG_ID attribute.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Russell King says:
====================
Four further jit compiler improves for 32-bit ARM.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Improve the 64-bit store implementation from:
ldr r6, [fp, #-8]
str r8, [r6]
ldr r6, [fp, #-8]
mov r7, #4
add r7, r6, r7
str r9, [r7]
to:
ldr r6, [fp, #-8]
str r8, [r6]
str r9, [r6, #4]
We leave the store as two separate STR instructions rather than using
STRD as the store may not be aligned, and STR can handle misalignment.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Rather than writing each 32-bit half of the 64-bit immediate value
separately when the register is on the stack:
movw r6, #45056 ; 0xb000
movt r6, #60979 ; 0xee33
str r6, [fp, #-44] ; 0xffffffd4
mov r6, #0
str r6, [fp, #-40] ; 0xffffffd8
arrange to use the double-word store when available instead:
movw r6, #45056 ; 0xb000
movt r6, #60979 ; 0xee33
mov r7, #0
strd r6, [fp, #-44] ; 0xffffffd4
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The hardware supposedly handles frames up to 10236 bytes and
implements .ndo_change_mtu() so accept 10236 minus the ethernet
header for a VLAN tagged frame on the netdevices. Use
ETH_MIN_MTU as minimum MTU.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initialization sequence for the ethernet, setting up
interrupt routing and such things, need to be done after
both the ports are clocked and reset. Before this the
config will not "take". Move the initialization to the
port probe function and keep track of init status in
the state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was not tested with two ports actually in use at
the same time. (I blame this on lack of actual hardware using
that feature.) Now after locating a system using both ports,
add necessary fix to make both ports come up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch over to using a module parameter and debug prints
that can be controlled by this or ethtool like everyone
else. Depromote all other prints to debug messages.
The phy_print_status() was already in place, albeit never
really used because the debuglevel hiding it had to be
set up using ethtool.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to calculate the hardware register enumerator
for the maximum L3 length isn't entirely simple to read.
Use the existing defines and rewrite the function into a
table look-up.
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Vesker says:
====================
devlink: Add support for region access
This is a proposal which will allow access to driver defined address
regions using devlink. Each device can create its supported address
regions and register them. A device which exposes a region will allow
access to it using devlink.
The suggested implementation will allow exposing regions to the user,
reading and dumping snapshots taken from different regions.
A snapshot represents a memory image of a region taken by the driver.
If a device collects a snapshot of an address region it can be later
exposed using devlink region read or dump commands.
This functionality allows for future analyses on the snapshots to be
done.
The major benefit of this support is not only to provide access to
internal address regions which were inaccessible to the user but also
to provide an additional way to debug complex error states using the
region snapshots.
Implemented commands:
$ devlink region help
$ devlink region show [ DEV/REGION ]
$ devlink region del DEV/REGION snapshot SNAPSHOT_ID
$ devlink region dump DEV/REGION [ snapshot SNAPSHOT_ID ]
$ devlink region read DEV/REGION [ snapshot SNAPSHOT_ID ]
address ADDRESS length length
Show all of the exposed regions with region sizes:
$ devlink region show
pci/0000:00:05.0/cr-space: size 1048576 snapshot [1 2]
pci/0000:00:05.0/fw-health: size 64 snapshot [1 2]
Delete a snapshot using:
$ devlink region del pci/0000:00:05.0/cr-space snapshot 1
Dump a snapshot:
$ devlink region dump pci/0000:00:05.0/fw-health snapshot 1
0000000000000000 0014 95dc 0014 9514 0035 1670 0034 db30
0000000000000010 0000 0000 ffff ff04 0029 8c00 0028 8cc8
0000000000000020 0016 0bb8 0016 1720 0000 0000 c00f 3ffc
0000000000000030 bada cce5 bada cce5 bada cce5 bada cce5
Read a specific part of a snapshot:
$ devlink region read pci/0000:00:05.0/fw-health snapshot 1 address 0
length 16
0000000000000000 0014 95dc 0014 9514 0035 1670 0034 db30
For more information you can check devlink-region.8 man page
Future:
There is a plan to extend the support to include a write command
as well as performing read and dump live region
v1->v2:
-Add a parameter to enable devlink region snapshot
-Allocate snapshot memory using kvmalloc
-Introduce destructor function devlink_snapshot_data_dest_t to avoid
double allocation
v2->v3:
-Fix incorrect comment in devlink.h for DEVLINK_ATTR_REGION_SIZE
from u32 to u64
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This parameter enables capturing region snapshot of the crspace
during critical errors. The default value of this parameter is
disabled, it can be enabled using devlink param commands.
It is possible to configure during runtime and also driver init.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
region_snapshot - When set enables capturing region snapshots
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crdump allows the driver to create a snapshot of the FW PCI
crspace and health buffer during a critical FW issue.
In case of a FW command timeout, FW getting stuck or a non zero
value on the catastrophic buffer, a snapshot will be taken.
The snapshot is exposed using devlink, cr-space, fw-health
address regions are registered on init and snapshots are attached
once a new snapshot is collected by the driver.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health buffer address is a 32 bit PCI address offset provided by
the FW. This offset is used for reading FW health debug data
located on the shared CR space. Cr space is accessible in both
driver and FW and allows for different queries and configurations.
Health buffer size is always 64B of readable data followed by a
lock which is used to block volatile CR space access.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DEVLINK_CMD_REGION_READ_GET used for both reading
and dumping region data. Read allows reading from a region specific
address for given length. Dump allows reading the full region.
If only snapshot ID is provided a snapshot dump will be done.
If snapshot ID, Address and Length are provided a snapshot read
will done.
This is used for both snapshot access and will be used in the same
way to access current data on the region.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>