We can now probe devices with device tree only configuration using
ti-sysc interconnect target module driver. Let's configure the
module, but keep the legacy "ti,hwmods" peroperty to avoid new boot
time warnings. The legacy property will be removed in later patches
together with the legacy platform data.
Note that we want to use separate compatible for omap34xx and
omap36xx so let's do that here too while at it.
Cc: devicetree@vger.kernel.org
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Vinod Koul <vkoul@kernel.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
See DM3730,DM275 data sheet (SPRS685B) footnote (6) in Table 4-19
which says that ABB must be switched to FBB mode when using the
OPP1G.
The LOD definition abb_mpu_iva already exists so that we need
to add plumbing for vbb-supply = <&abb_mpu_iva>
and define two voltage vectors for each OPP so that the abb LDO
is also updated by the ti-cpufreq driver.
We also must switch the ti_cpufreq_soc_data to multi_regulator.
Note: reading out the abb reglator voltage to verify that
it does do transitions can be done by
cat /sys/devices/platform/68000000.ocp/483072f0.regulator-abb-mpu/regulator/regulator.*/microvolts
Likewise, read the twl4030 provided VDD voltage by
cat /sys/devices/platform/68000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:twl@48:regulator-vdd1/regulator/regulator.*/microvolts
Note: to check if the ABB FBB is enabled/disabled, check
registers
PRM_LDO_ABB_CTRL 0x483072F4 bit 3:0 1=bypass 5=FBB
PRM_LDO_ABB_SETUP 0x483072F0 0x00=bypass 0x11=FBB
e.g.
/dev/mem opened.
Memory mapped at address 0xb6fe4000.
Value at address 0x483072F4 (0xb6fe42f4): 0x3205
/dev/mem opened.
Memory mapped at address 0xb6f89000.
Value at address 0x483072F4 (0xb6f892f4): 0x3201
Note: omap34xx and am3517 have/need no comparable LDO
or mechanism.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
With the driver installed, we can change the opp-v1 table format
to opp-v2.
In addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev
in the same patch, because doing either first breaks operation and
may make trouble in bisect.
We also can remove opp-v1 table for omap3-n950-n9 since its 1GHz
capability is now automatically detected.
We also fix a wrong OPP4 voltage for omap3430 which must be
0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject
this OPP.
Note: the high speed OPPs that were not available in the opp-v1 tables
are tagged "turbo-mode;" which means they are not automatically
activated by the govenors or cpu-freq.
To enable you have to write
echo 1 >/sys/devices/system/cpu/cpufreq/boost
Note: to hard disable an OPP in a board.dts file use e.g.
&cpu0_opp_table: {
/delete-node/ opp1g-1000000000; /* do not use */
};
or alternatively:
&cpu0_opp_table: {
opp1g-1000000000 {
status = "disabled"; /* do not use */
};
};
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Looks like omap34xx OCP registers are not readable unlike on omap36xx.
We use SGX revision register instead of the OCP revision register for
34xx and do not configure any SYSCONFIG register unlike for 36xx.
I've tested that the interconnect target module enables and idles
just fine with PM runtime control via sys:
# echo on > $(find /sys -name control | grep \/5000); rwmem 0x5000fe10
# rwmem 0x50000014 # SGX revision register on 36xx
0x50000014 = 0x00010205
# echo auto > $(find /sys -name control | grep \/5000)
# rwmem 0x5000fe00
And when idled, it will produce "Bus error" as expected.
Cc: Adam Ford <aford173@gmail.com>
Cc: Filip Matijević <filip.matijevic.pz@gmail.com>
Cc: "H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: moaz korena <moaz@korena.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Philipp Rossak <embed3d@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's update the existing users with features and clock data as
specified in the binding. This is currently the smartreflex for most
part, and also few omap4 modules with no child device driver like
mcasp, abe iss and gfx.
Note that we had few mistakes that did not get noticed as we're still
probing the SmartReflex driver with legacy platform data and using
"ti,hwmods" legacy property for ti-sysc driver.
So let's fix the omap4 and dra7 smartreflex registers as there is no
no revision register.
And on omap4, the mcasp module has a revision register according to
the TRM.
And for omap34xx we need a different configuration compared to 36xx.
And the smartreflex on 3517 we've always kept disabled so let's
remove any references to it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /ocp has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"bandgap has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Driver for omap3 with documentation is there since v4.4-rc1.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: added thermal-sensor-cells as suggested by Roger]
Signed-off-by: Tony Lindgren <tony@atomide.com>
As pointed out by Stephen Rothwell, commit e52117638b ("ARM: dts:
omap3: Add DT entries for OMAP 3 ISP") conflicts with b8845074cf
("ARM: dts: omap3: add minimal l4 bus layout with control module support")
in non-obvious ways, causing a build failure when both patches
are present.
This merges the two branches that introduce the respective changes
into the next/late branch to resolve the way that Stephen suggested,
as confirmed by Tony.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.org/lkml/2015/4/6/436
Acked-by: Tony Lindgren <tony@atomide.com>
The resources the ISP needs are slightly different on 3[45]xx and 3[67]xx.
Especially the phy-type property is different.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: use omap3_scm_general instead of scm_conf for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add SSI device tree data for OMAP3 and Nokia N900.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Tested-By: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT data for OMAP3 display subsystem, which contains the following
blocks:
dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
OMAP3630 DPLL4 is different than on OMAP3430, in that it doesn't have
the x2 multiplier for its outputs. This is not currently reflected in
the clock DT data.
Fix the issue by setting the clock multiplier to 1 (instead of 2) for the
DPLL4 output clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add ABB device node for OMAP36xx family of devices. Data is based on
OMAP36XX Technical Reference Manual revision AB (Dec 2012).
[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for Samsung
chips. Additionally there are other smaller clock driver changes and
several last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRJD
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework changes from Mike Turquette:
"The second half of the clock framework pull requeust for 3.14 is
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for
Samsung chips.
Additionally there are other smaller clock driver changes and several
last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request"
[ Fix up stupid compile error in the source tree with evil merge - Grumpy Linus ]
* tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux: (49 commits)
clk: sort Makefile
clk: sunxi: fix overflow when setting up divided factors
clk: Export more clk-provider functions
dt-bindings: qcom: Fix warning with duplicate dt define
clk: si5351: remove variant from platform_data
clk: samsung: Remove unneeded semicolon
clk: qcom: Fix modular build
ARM: OMAP3: use DT clock init if DT data is available
ARM: AM33xx: remove old clock data and link in new clock init code
ARM: AM43xx: Enable clock init
ARM: OMAP: DRA7: Enable clock init
ARM: OMAP4: remove old clock data and link in new clock init code
ARM: OMAP2+: io: use new clock init API
ARM: OMAP2+: PRM: add support for initializing PRCM clock modules from DT
ARM: OMAP3: hwmod: initialize clkdm from clkdm_name
ARM: OMAP: hwmod: fix an incorrect clk type cast with _get_clkdm
ARM: OMAP2+: clock: use driver API instead of direct memory read/write
ARM: OMAP2+: clock: add support for indexed memmaps
ARM: dts: am43xx clock data
ARM: dts: AM35xx: use DT clock data
...
This patch creates a unique node for each clock in the OMAP3 power,
reset and clock manager (PRCM).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The omap3_pmx_core pinmux device in the device tree handles the system
controller module (SCM) PADCONFS fonction. Its control registers are
split in two distinct areas, with other SCM registers in-between. Those
other registers can't thus be requested by other drivers as the memory
region gets reserved by the pinmux driver.
Split the omap3_pmx_core device tree node in two for the two memory
regions. The second region address and size depends on the SoC model.
The change in omap3.dtsi fixes an "external abort on non-linefetch" when
doing
cat /sys/kernel/debug/pinctrl/.../pins
on a Nokia N900.
Note that the core2 padconf region is different for 3430 vs 3630,
and does not exist on 3517 as noted by Nishanth Menon <nm@ti.com>.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-By: Sebastian Reichel <sre@debian.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated for 3430 vs 3630 core2 based on Nishant's patch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like omap3 is still relying on hwmod data for some basic
device tree information. Let's add the information to omap3.dtsi
so we can remove the related hwmod data once omap3 is DT only.
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
commit 3027e26 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add DT OPP table for OMAP36xx/37xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
OPP data here is based on existing opp3xxx_data.c
This is in preparation to use generic cpufreq-cpu0 driver for device
tree enabled boot. Legacy non device tree enabled boot continues to
use omap-cpufreq.c and opp3xxx_data.c.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The extra serial port is not available on 34xx. And the current
omap3-beagle.dts file is for omap3-beagle-xm.dts as it lists 512MB
of memory.
Please somebody submit a new omap3-beagle.dts for the original 34xx
BeagleBoard after testing it properly.
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
