Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the hardware crypto acceleration used in the artpec6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.
Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.
At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove 0x prefix from clkctrl unit address.
This silences the following dtc warning:
Warning (unit_address_format):
Node /clkctrl@0xf8000000 unit name should not have leading "0x"
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.
Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
"interrupt-parent" property is declared in root node, so it is global
to all nodes. This property is re-declared in few sub-nodes. To avoid
duplication this property is removed from following sub-nodes:
pmu, amba@0, amba@0/ethernet.
Signed-off-by: Surender Polsani <surenderp@techveda.org>
Acked-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
Use the cache settings that were determined to give best performance
on artpec-6 typical workloads.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The clock binding for the main clock controller was changed to an
indexed controller style binding on request of the clk
maintainers. This updates the dtsi to use the new bindings.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Relaxed the license on the dtsi to permit use in other projects.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Initial device tree for the Artpec-6 SoC.
Signed-off-by: Lars Persson <larper@axis.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
