The comment should have been removed when new GPIO direction
definitions were taken in use as the function logic was changed. It
is now perfectly valid and Ok to hit the return from the bottom of
the direction getting function.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The GPIO controller found on Tegra186 and later supports debouncing for
inputs for up to 255 ms.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The controls for the GG port on Tegra194 resides in the power partition
of the C5 PCIe controller and its interrupt route mapping can therefore
not be programmed by early boot firmware along with that of the other
ports.
Detect this generically by looking at which controls have already been
locked down using the security registers and fill in default values for
controls that are unlocked.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The register offsets for a given bank and port can be easily derived
from the bank and port indices. Update the port descriptors to list only
the bank and port numbers to simplify this.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add the GPIOHANDLE_SET_CONFIG_IOCTL to the gpio chardev.
The ioctl allows some of the configuration of a requested handle to be
changed without having to release the line.
The primary use case is the changing of direction for bi-directional
lines.
Based on initial work by Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move validation of line handle flags into helper function.
This reduces the size and complexity of linehandle_create and allows the
validation to be reused elsewhere.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for the pull up/down state set via gpiolib line requests to
be reflected in the state of the mockup.
Use case is for testing of the GPIO uAPI, specifically the pull up/down
flags.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Allow pull up/down bias to be set on output lines.
Use case is for open source or open drain applications where
internal pull up/down may conflict with external biasing.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Allow pull up/down bias to be disabled, allowing the line to float
or to be biased only by external circuitry.
Use case is for where the bias has been applied previously, either
by default or by the user, but that setting may conflict with the
current use of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for pull up/down to lineevent_create.
Use cases include receiving asynchronous presses from a
push button without an external pull up/down.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add pull-up/pull-down flags to the gpio line get and
set ioctl() calls. Use cases include a push button
that does not have an external resistor.
Addition use cases described by Limor Fried (ladyada) of
Adafruit in this PR for Adafruit_Blinka Python lib:
https://github.com/adafruit/Adafruit_Blinka/pull/59
Signed-off-by: Drew Fustini <drew@pdp7.com>
[Kent: added BIAS to GPIO flag names and restrict application to input
lines]
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The irq_chip .name field should contain the device's class name, not the
instance's name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The irq_chip .name field should contain the device's class name, not the
instance's name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The bd70528 GPIO driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell
for GPIO is added.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
"ser_device.state" is "unsigned long", i.e. 32-bit or 64-bit, depending
on the platform. Hence casting its address to "u32 *", and calling
debugfs_create_x32() breaks operation on 64-bit platforms.
Fix this by using the new debugfs_create_xul() helper instead.
Fixes: 9b27105b4a ("net-caif-driver: add CAIF serial driver (ldisc)")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191025094130.26033-4-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new debugfs_create_xul() helper instead of open-coding the same
operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Link: https://lore.kernel.org/r/20191025094130.26033-3-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8c550e94b8.
This was prematurely applied and we need to back it out to merge
a better version of the development track for this feature.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_gpiochip_add(), when fails, calls gpiochip_remove_pin_ranges().
ADD:
gpiochip_add_data_with_key() ->
of_gpiochip_add() -> (ERROR path)
gpiochip_remove_pin_ranges()
At the same time of_gpiochip_remove() calls exactly the above mentioned
function unconditionally and so does gpiochip_remove().
REMOVE:
gpiochip_remove() ->
gpiochip_remove_pin_ranges()
of_gpiochip_remove() ->
gpiochip_remove_pin_ranges()
Since gpiochip_remove() calls gpiochip_remove_pin_ranges() unconditionally,
we have duplicate call to the same function when it's not necessary.
Move gpiochip_remove_pin_ranges() from of_gpiochip_add() to gpiochip_add()
to avoid duplicate calls and be consistent with the explicit call in
gpiochip_remove().
Fixes: e93fa3f243 ("gpiolib: remove duplicate pin range code")
Depends-on: f7299d441a ("gpio: of: Fix of_gpiochip_add() error path")
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for creating device links out of more DT properties.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105065000.50407-4-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a DEFINE_SIMPLE_PROP macro to make it easy to add support for simple
properties with fixed names that just list phandles and phandle args.
Add a DEFINE_SUFFIX_PROP macro to make it easy to add support for
properties with fixes suffix that just list phandles and phandle args.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105065000.50407-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding a debug log instead of silently ignoring a phandle for an early
device. Also, return the right error code instead of 0 even though the
actual execution flow won't change.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191105065000.50407-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's hard for occasional GPIO code reader/writer to know if values 0/1
equal to IN or OUT. Use defined GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT to help them out.
NOTE - for gpio-amd-fch and gpio-bd9571mwv:
This commit also changes the return value for direction get to equal 1
for direction INPUT. Prior this commit these drivers might have
returned some other positive value but 1 for INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At least for me it is difficult to remember the meaning of GPIO
direction values. Define GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT so that occasional GPIO contributors would
not need to always check the meaning of hard coded values 1 and 0.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The table of devicetree identifiers is annotated as __initconst
indicating that it can be discarded after kernel boot but it is
referenced from the driver struct which has no init annotation leading
to a linker warning:
WARNING: vmlinux.o(.data+0x82d58): Section mismatch in reference from the variable bcm_iproc_gpio_driver to the variable .init.rodata:bcm_iproc_gpio_of_match
The variable bcm_iproc_gpio_driver references
the variable __initconst bcm_iproc_gpio_of_match
Since drivers can be probed after init the lack of annotation on the
driver struct is correct so remove the annotation from the match table.
Fixes: 6a41b6c5fc ("gpio: Add xgs-iproc driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide a variant of devm_platform_ioremap_resource() that allows to
lookup resources from platform devices by name rather than by index.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191022084318.22256-7-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new devm_platform_ioremap_resource_wc() helper instead of
devm_ioremap_wc() combinded with a call to platform_get_resource().
Also use devm_platform_ioremap_resource() where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191022084318.22256-6-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to add the write-combined variant of devm_ioremap_resource().
Let's first implement __devm_ioremap_resource() which takes
an additional argument type. The types are the same as for
__devm_ioremap(). The existing devm_ioremap_resource() now simply
calls __devm_ioremap_resource() with regular DEVM_IOREMAP type.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191022084318.22256-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO irqchip needs to initialize the valid mask
before initializing the IRQ hardware, because sometimes
the latter require the former to be executed first.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20191030122914.967-1-linus.walleij@linaro.org
Acked-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-rdma@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 8f86a5b4ad.
It has been established that this causes a boot regression on
both Baytrail and Cherrytrail SoCs, and we can't have that in
the final kernel release, so we need to revert it.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 6658f87f21.
This revert is a prerequisite for the later revert of commit
8f86a5b4ad.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 4c87540940.
This revert is a prerequisite for the later revert of commit
8f86a5b4ad.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is useful for users who are trying to identify the firmwares in use
on their system.
Signed-off-by: Drew DeVault <sir@cmpwn.com>
Link: https://lore.kernel.org/r/20191103180646.34880-1-sir@cmpwn.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"dw_mci.state" is an enum, which is compatible with u32, so there is no
need to cast its address, preventing further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-8-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"dw_mci.pending_events" and "dw_mci.completed_events" are "unsigned
long", i.e. 32-bit or 64-bit, depending on the platform. Hence casting
their addresses to "u32 *", and calling debugfs_create_x32() breaks
operation on 64-bit platforms.
Fix this by using the new debugfs_create_xul() helper instead.
Fixes: f95f3850f7 ("mmc: dw_mmc: Add Synopsys DesignWare mmc host driver.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-7-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"atmel_mci.state" is an enum, which is compatible with u32, so there is
no need to cast its address, preventing further compiler checks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-6-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"atmel_mci.pending_events" and "atmel_mci.completed_events" are
"unsigned long", i.e. 32-bit or 64-bit, depending on the platform.
Hence casting their addresses to "u32 *", and calling
debugfs_create_x32() breaks operation on 64-bit platforms.
Fix this by using the new debugfs_create_xul() helper instead.
Fixes: deec9ae31e ("atmel-mci: debugfs support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20191025094130.26033-5-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
