This patch adds a specific busy_complete callback for sdmmc variant.
sdmmc has 2 status flags:
-busyd0: This is a hardware status flag (inverted value of d0 line).
it does not generate an interrupt.
-busyd0end: This indicates only end of busy following a CMD response.
On busy to Not busy changes, an interrupt is generated (if unmask)
and BUSYD0END status flag is set. Status flag is cleared by writing
corresponding interrupt clear bit in MMCICLEAR.
The legacy busy completion has no dedicated interrupt for the end
of busy, so it's must monitor step by step the busy progression.
On sdmmc variant, this procedure is not needed, it's just need
to wait the busyd0end interrupt.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds busy_completion callback at mmci_host_ops
to allow to define a specific busy completion by variant.
The legacy code corresponding to busy completion used
by ux500 variants is moved to ux500_busy_complete function.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the stm32_sdmmc variant, the datatimer is active not only during
data transfers with the DPSM, but also while waiting for the busyend
IRQs from commands having the MMC_RSP_BUSY flag set. This leads to an
incorrect IRQ being raised to signal MCI_DATATIMEOUT error, which
simply breaks the behaviour.
Address this by updating the datatimer value before sending a command
having the MMC_RSP_BUSY flag set. To inform the mmc core about the
maximum supported busy timeout, which also depends on the current
clock rate, set ->max_busy_timeout (in ms).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows to get datactrl configuration specific
at variant. This introduce more flexibility on datactlr
value.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines get_dctrl_cfg callback for sdmmc variant.
sdmmc variant has specific stm32 transfer modes.
sdmmc data transfer mode selection could be:
-Block data transfer ending on block count.
-SDIO multibyte data transfer.
-MMC Stream data transfer (not used).
-Block data transfer ending with STOP_TRANSMISSION command.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds get_datactrl_cfg callback in mmci_host_ops
to allow to get datactrl configuration specific at variant.
Common helper function is defined and could be call by variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's good practice to share functions via header files, rather than from
the c-files. Therefore, let's move sdmmc_variant_init() to mmci.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Barre <ludovic.barre@st.com>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It seems a bit silly to have a header file to share only the
qcom_variant_init() function. So, let's just drop it and move the
declaration of the function into the common mmci.h instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Some of the DMA functions are shared via mmci.h, however they are not
implemented unless CONFIG_DMA_ENGINE is set. Therefore, add that constraint
to the header file as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The current approach with sending a CMD12 (STOP_TRANSMISSION) to complete a
data transfer request, either because of using the open-ended transmission
type or because of receiving an error during a pre-defined data transfer,
isn't sufficient for the STM32 sdmmc variant. More precisely, this variant
needs to clear the DPSM ("Data Path State Machine") by sending a CMD12, for
all failing ADTC commands.
Support this, by adding a struct mmc_command inside the struct mmci_host
and initialize it to a CMD12 during ->probe(). Let's also add checks for
the new conditions, to enable mmci_data_irq() and mmci_cmd_irq() to
postpone the calls to mmci_request_end(), but instead send the CMD12.
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Barre <ludovic.barre@st.com>
On cmd12 (STOP_TRANSMISSION), STM32 sdmmc variant needs to set
cmdstop bit in command register. The CPSM ("Command Path State Machine")
treats the command as a Stop Transmission command and signals
abort to the DPSM ("Data Path State Machine").
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a stm32 sdmmc variant, rev 1.1.
Introduces a new Manufacturer id "0x53, ascii 'S' to define
new stm32 sdmmc family with clean range of amba
revision/configurations bits (corresponding to sdmmc_ver
register with major/minor fields).
Add 2 variants properties:
-dma_lli, to enable link list support.
-stm32_idmabsize_mask, defines the range of SDMMC_IDMABSIZER register
which specify the number bytes per buffer.
DT properties for sdmmc:
-Indicate signal directions (only one property
for d0dir, d123dir, cmd_dir)
-Select command and data phase relation.
-Select "clock in" from an external driver.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STM32 sdmmc variant has a different clock divider.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a optional reset management.
STM32 sdmmc variant needs to reset hardware block
during the power cycle procedure (for re-initialization).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to not read datacnt register.
Needed to support the STM32 sdmmc variant. MMCIDATACNT
register should be read only after the data transfer is completed.
When reading after an error event the read data count value may be
different from the real number of data bytes transferred.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a boolean property to allow to write datactrl
before to send command, whatever the command type (read or write).
Needed to support the STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define specific pio mask for variants.
Needed to support the STM32 sdmmc variant which has some bits
with different meaning (bits: 21,20,13,12,9)
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds datactrl variant property to define
dpsm enable bit. Needed to support the STM32 variant
(STM32 has no dpsm enable bit).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds command variant properties to define
cpsm enable bit and responses.
Needed to support the STM32 variant (shift of cpsm bit,
specific definition of commands response).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All variants don't pretend to have a startbiterr.
-While data error check, if status register return an error
(like MCI_DATACRCFAIL) we must avoid to check MCI_STARTBITERR
(if not desired).
-expand start_err to MCI_IRQENABLE to avoid to set this bit by default.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch allows to define a datactrl block size
by variant, requested by STM32 sdmmc variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds set_clkreg and set_pwrreg callbacks
at mmci_host_ops to allow to call specific variant.
extends visibility of mmci_write_clk/pwrreg functions
to be used into specific file variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds validate_data callback at mmci_host_ops
to check specific constraints of variant.
Move mmci_validate_data function to regroup mmci_host_ops interfaces.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_error callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_finalize callback at mmci_host_ops
to allow to call specific variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds dma_start callback to mmci_host_ops.
Create a generic mmci_dma_start function which regroup
common action between variant.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds prepare/unprepare callbacks to mmci_host_ops.
Like this mmci_pre/post_request can be generic, mmci_prepare_data
and mmci_unprepare_data provide common next_cookie management.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
-Introduces dma_priv pointer to define specific
needs for each dma engine. This patch is needed to prepare
sdmmc variant with internal dma which not use dmaengine API.
-Moves next cookie to mmci host structure to share same cookie
management between all variants.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch creates a common mmci_dma_setup/release which calls
dma_setup/release callbacks of mmci_host_ops and manages
common features like use_dma... If there is a fallbacks to
pio mode, dma functions must check use_dma.
error management:
-mmci_dmae_setup fail if Tx and Rx dma channels are not defined
-qcom_dma_setup fail if one of both dma channels is not defined,
Qcom has no specific resource to release, just mmci dmae resource.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent versions of checkpatch have a new warning based on a documented
preference of Linus to not use bool in structures due to wasted space and
the size of bool is implementation dependent. For more information, see
the email thread at https://lkml.org/lkml/2017/11/21/384
fix checkpatch --strict issues:
-CHECK: Avoid using bool structure members because of possible alignment
issues - see: https://lkml.org/lkml/2017/11/21/384
-WARNING: Avoid using bool as bitfield. Prefer bool bitfields as
unsigned int or u<8|16|32>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch internalizes the dma_inprogress into mmci dma interfaces.
This allows to simplify and prepare the next dma callbacks
for mmci host ops. dma_inprogress is called in mmci_dma_data_error
and mmci_dma_finalize.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a first step to improve the variant specific code for mmci, add a
->dma_setup() callback to the struct mmci_host_ops.
To show its use, let's deploy the callback for the qcom dml, which involves
also to the assign the mmci_host_ops pointer from the variant ->init()
callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.
Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
If variant hasn't the control bit to switch pads in opendrain mode,
we can achieve the same result by asking to the pinmux driver to
configure pins for us.
This patch make the mmci driver able to do this whenever needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Two mask registers are used in order to select which events have to
actually generate an interrupt on each IRQ line.
It seems that in the single-IRQ case it's assumed that the IRQs lines
are simply OR-ed, while the two mask registers are still present. The
driver still programs the two mask registers separately.
However the STM32 variant has only one IRQ, and also has only one mask
register.
This patch prepares for STM32 variant support by making the driver using
only one mask register.
This patch also optimize the MMCIMASK1 mask usage by caching it into
host->mask1_reg which avoid to read it into mmci_irq().
Tested only on STM32 variant. RFT for variants other than STM32
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
commit 64b12a68a9
"mmc: core: fix prepared requests while doing bkops"
is fixing a bug in the wrong way. A bug in the MMCI
device driver is fixed by amending the MMC core.
Thinking about it: what the pre- and post-callbacks
are doing is to essentially map and unmap SG lists
for DMA transfers. Why would we not be able to do that
just because a BKOPS command is sent inbetween?
Having to unprepare/prepare the next asynchronous
request for DMA seems wrong.
Looking the backtrace in that commit we can see what
the real problem actually is:
mmci_data_irq() is calling mmci_dma_unmap() twice
which is goung to call arm_dma_unmap_sg() twice
and v7_dma_inv_range() twice for the same sglist
and that will crash.
This happens because a request is prepared, then
a BKOPS is sent. The IRQ completing the BKOPS command
goes through mmci_data_irq() and thinks that a DMA
operation has just been completed because
dma_inprogress() reports true. It then proceeds to
unmap the sglist.
But that was wrong! dma_inprogress() should NOT be
true because no DMA was actually in progress! We had
just prepared the sglist, and the DMA channel
dma_current has been configured, but NOT started!
Because of this, the sglist is already unmapped when
we get our actual data completion IRQ, and we are
unmapping the sglist once more, and we get this crash.
Therefore, we need to revert this solution pushing
the problem to the core and causing problems, and
instead augment the implementation such that
dma_inprogress() only reports true if some DMA has
actually been started.
After this we can keep the request prepared during the
BKOPS and we need not unprepare/reprepare it.
Fixes: 64b12a68a9 ("mmc: core: fix prepared requests while doing bkops")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ST Micro-specific busy detection was made after the assumption
that only this variant supports busy detection. So when doing busy
detection, the host immediately tries to use some ST-specific
register bits.
Since the qualcomm variant also supports some busy detection
schemes, encapsulate the variant flags better in the variant struct
and prepare to add more variants by just providing some bitmasks
to the logic.
Put the entire busy detection logic within an if()-clause in the
mmci_cmd_irq() function so the code is only executed when busy
detection is enabled, and so that it is kept in (almost) one
place, and add comments describing what is going on so the
code can be understood.
Tested on the Ux500 by introducing some prints in the busy
detection path and noticing how the IRQ is enabled, used and
disabled successfully.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There was some confusion in the CPSM (Command Path State Machine)
and DPSM (Data Path State Machine) regarding the naming of the
registers, clarify the meaning of this acronym so the naming is
understandable, and consistently use BIT() to define these fields.
Consequently name the register bit defines MCI_[C|D]PSM_* and
adjust the driver as well.
Include new definitions for a few bits found in a patch from
Srinivas Kandagatla.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MCIFIFOCNT register behaviour on Qcom chips is very different than the other
pl180 integrations. MCIFIFOCNT register contains the number of
words that are still waiting to be transferred through the FIFO. It keeps
decrementing once the host CPU reads the MCIFIFO. With the existing logic and
the MCIFIFOCNT behaviour, mmci_pio_read will loop forever, as the FIFOCNT
register will always return transfer size before reading the FIFO.
Also the data sheet states that "This register is only useful for debug
purposes and should not be used for normal operation since it does not reflect
data which may or may not be in the pipeline".
This patch implements a qcom specific get_rx_fifocnt function which is
implemented based on status register flags. Based on qcom_fifo flag in
variant data structure, the corresponding get_rx_fifocnt function is selected.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
On Controllers like Qcom SD card controller where cclk is mclk and mclk should
be directly controlled by the driver.
This patch adds support to control mclk directly in the driver, and also
adds explicit_mclk_control flag in variant structure giving more flexibility
to the driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[Ulf Hansson] Fixed checkpatch warning
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a Qualcomm SD Card controller specific register variations
to header file. Qualcomm SDCC controller is pl180, with slight changes in
the register layout from standard pl180 register set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove the option to provide signal direction configuration and
feeback clock as platform data, enforce it through DT.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To avoid duplication of code while handling card detect and write
protect GPIO pins/irqs, let's convert to use the mmc gpio API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
The ux500 variants have HW busy detection support, which is indicated
by the busy_detect flag. For these variants let's enable the
MMC_CAP_WAIT_WHILE_BUSY flag and add the support for it.
The mmc core will provide the RSP_BUSY command flag for those requests
we should care about busy detection. Regarding the max_busy_timeout,
the HW don't support busy detection timeouts so at this initial step
let's make it simple and set it to zero to indicate we are able to
support any timeout.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Johan Rudholm <jrudholm@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
These four (so far unused) flags are only found in the ST Micro
versions of MMCI, so infix them properly with the _ST_ infix.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no need for every driver to fetch a pinctrl handle and to
select the default state. Instead this is handled by the device driver
core, thus we can remove this piece of code from mmci.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
