Use one code block when returning because the interface type is
unsupported and also check if some unsupported port gets configured.
In addition fix a double the and use dsa_is_cpu_port() instated of
manually getting the CPU port.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch and the MAC are in one IP core and they use the same clock
signal from the clock generation unit.
Currently the clock architecture in the lantiq SoC code does not allow
to easily share the same clocks, this has to be fixed by switching to
the common clock framework.
As a workaround the clock of the switch and MAC should be activated when
the MAC gets probed and only disabled when the MAC gets removed. This
way it is ensured that the clock is always enabled when the switch or
MAC is used. The switch can not be used without the MAC.
This fixes a data bus error when rebooting the system and deactivating
the switch and mac and later accessing some registers in the cleanup
while the clocks are disabled.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Use one compatible line per line in the documentation
* Remove SoC revision depended compatible lines, we can detect that in
the driver
* Use lower case letters in hex addresses
* Fix the size of the address ranges in the example, this now matches
the sizes used by the SoC. The old ones will also work, this just adds
some empty address space.
* Change the reg size of the gphy-fw node
Fixes: 86ce2bc73c ("dt-bindings: net: dsa: Add lantiq, xrx200-gswip DT bindings")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use lower case letters in the addresses of the device tree binding.
In addition replace eth with ethernet and fix the size of the reg
element in the example. The additional range does not contain any
registers but is used for the IP block on the this SoC.
Fixes: 839790e88a ("dt-bindings: net: Add lantiq, xrx200-net DT bindings")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/hisilicon/hns/hns_dsaf_gmac.c:322:5: warning:
symbol 'hns_gmac_wait_fifo_clean' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value from of_reset_control_array_get_exclusive() is not
checked correctly. The test is done against a wrong variable. This
patch fix it.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When async support was added it needed to access the sk from the async
callback to report errors up the stack. The patch tried to use space
after the aead request struct by directly setting the reqsize field in
aead_request. This is an internal field that should not be used
outside the crypto APIs. It is used by the crypto code to define extra
space for private structures used in the crypto context. Users of the
API then use crypto_aead_reqsize() and add the returned amount of
bytes to the end of the request memory allocation before posting the
request to encrypt/decrypt APIs.
So this breaks (with general protection fault and KASAN error, if
enabled) because the request sent to decrypt is shorter than required
causing the crypto API out-of-bounds errors. Also it seems unlikely the
sk is even valid by the time it gets to the callback because of memset
in crypto layer.
Anyways, fix this by holding the sk in the skb->sk field when the
callback is set up and because the skb is already passed through to
the callback handler via void* we can access it in the handler. Then
in the handler we need to be careful to NULL the pointer again before
kfree_skb. I added comments on both the setup (in tls_do_decryption)
and when we clear it from the crypto callback handler
tls_decrypt_done(). After this selftests pass again and fixes KASAN
errors/warnings.
Fixes: 94524d8fc9 ("net/tls: Add support for async decryption of tls records")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Vakul Garg <Vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as ip_gre, use gre_parse_header to parse gre header in gre error
handler code.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gre_parse_header stops parsing when csum_err is encountered, which means
tpi->key is undefined and ip_tunnel_lookup will return NULL improperly.
This patch introduce a NULL pointer as csum_err parameter. Even when
csum_err is encountered, it won't return error and continue parsing gre
header as expected.
Fixes: 9f57c67c37 ("gre: Remove support for sharing GRE protocol hook.")
Reported-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY_POLL is defined as -1 which means that we would be setting all flags of the
PHY driver, this is also not a valid flag to tell PHYLIB about, just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti says:
====================
net/sched: act_police: lockless data path
the data path of 'police' action can be faster if we avoid using spinlocks:
- patch 1 converts act_police to use per-cpu counters
- patch 2 lets act_police use RCU to access its configuration data.
test procedure (using pktgen from https://github.com/netoptimizer):
# ip link add name eth1 type dummy
# ip link set dev eth1 up
# tc qdisc add dev eth1 clsact
# tc filter add dev eth1 egress matchall action police \
> rate 2gbit burst 100k conform-exceed pass/pass index 100
# for c in 1 2 4; do
> ./pktgen_bench_xmit_mode_queue_xmit.sh -v -s 64 -t $c -n 5000000 -i eth1
> done
test results (avg. pps/thread):
$c | before patch | after patch | improvement
----+--------------+--------------+-------------
1 | 3518448 | 3591240 | irrelevant
2 | 3070065 | 3383393 | 10%
4 | 1540969 | 3238385 | 110%
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
use RCU instead of spinlocks, to protect concurrent read/write on
act_police configuration. This reduces the effects of contention in the
data path, in case multiple readers are present.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use per-CPU counters, instead of sharing a single set of stats with all
cores. This removes the need of using spinlock when statistics are read
or updated.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In CXGB4_DCB_STATE_FW_INCOMPLETE state check if the dcb
version is changed and update the dcb supported version.
- Also, fill the priority code point value for priority
based flow control.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
print per rx-queue packet errors in sge_qinfo
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not put host-endian 0 or 1 into big endian feild.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcpu_lstats is defined in several files, so unify them as one
and move to header file
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLA usage from the kernel[1], this
removes the VLA used for the emac xaht registers size. Since the size
of registers can only ever be 4 or 8, as detected in emac_init_config(),
the max can be hardcoded and a runtime test added for robustness.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Ivan Mikhaylov <ivan@de.ibm.com>
Cc: netdev@vger.kernel.org
Co-developed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "fallthru" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a GSO segment that consists of encapsulated packets, the
skb->mac_len of the segments can end up being set wrong, causing packet
drops in particular when using act_mirred and ifb interfaces in
combination with a qdisc that splits GSO packets.
This happens because at the time skb_segment() is called, network_header
will point to the inner header, throwing off the calculation in
skb_reset_mac_len(). The network_header is subsequently adjust by the
outer IP gso_segment handlers, but they don't set the mac_len.
Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6
gso_segment handlers, after they modify the network_header.
Many thanks to Eric Dumazet for his help in identifying the cause of
the bug.
Acked-by: Dave Taht <dave.taht@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the Device Tree is not providing the per-port interrupts, do not fail
during b53_srab_irq_enable() but instead bail out gracefully. The SRAB driver
is used on the BCM5301X (Northstar) platforms which do not yet have the SRAB
interrupts wired up.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang says:
====================
vhost_net TX batching
This series tries to batch submitting packets to underlayer socket
through msg_control during sendmsg(). This is done by:
1) Doing userspace copy inside vhost_net
2) Build XDP buff
3) Batch at most 64 (VHOST_NET_BATCH) XDP buffs and submit them once
through msg_control during sendmsg().
4) Underlayer sockets can use XDP buffs directly when XDP is enalbed,
or build skb based on XDP buff.
For the packet that can not be built easily with XDP or for the case
that batch submission is hard (e.g sndbuf is limited). We will go for
the previous slow path, passing iov iterator to underlayer socket
through sendmsg() once per packet.
This can help to improve cache utilization and avoid lots of indirect
calls with sendmsg(). It can also co-operate with the batching support
of the underlayer sockets (e.g the case of XDP redirection through
maps).
Testpmd(txonly) in guest shows obvious improvements:
Test /+pps%
XDP_DROP on TAP /+44.8%
XDP_REDIRECT on TAP /+29%
macvtap (skb) /+26%
Netperf TCP_STREAM TX from guest shows obvious improvements on small
packet:
size/session/+thu%/+normalize%
64/ 1/ +2%/ 0%
64/ 2/ +3%/ +1%
64/ 4/ +7%/ +5%
64/ 8/ +8%/ +6%
256/ 1/ +3%/ 0%
256/ 2/ +10%/ +7%
256/ 4/ +26%/ +22%
256/ 8/ +27%/ +23%
512/ 1/ +3%/ +2%
512/ 2/ +19%/ +14%
512/ 4/ +43%/ +40%
512/ 8/ +45%/ +41%
1024/ 1/ +4%/ 0%
1024/ 2/ +27%/ +21%
1024/ 4/ +38%/ +73%
1024/ 8/ +15%/ +24%
2048/ 1/ +10%/ +7%
2048/ 2/ +16%/ +12%
2048/ 4/ 0%/ +2%
2048/ 8/ 0%/ +2%
4096/ 1/ +36%/ +60%
4096/ 2/ -11%/ -26%
4096/ 4/ 0%/ +14%
4096/ 8/ 0%/ +4%
16384/ 1/ -1%/ +5%
16384/ 2/ 0%/ +2%
16384/ 4/ 0%/ -3%
16384/ 8/ 0%/ +4%
65535/ 1/ 0%/ +10%
65535/ 2/ 0%/ +8%
65535/ 4/ 0%/ +1%
65535/ 8/ 0%/ +3%
Please review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements XDP batching for vhost_net. The idea is first to
try to do userspace copy and build XDP buff directly in vhost. Instead
of submitting the packet immediately, vhost_net will batch them in an
array and submit every 64 (VHOST_NET_BATCH) packets to the under layer
sockets through msg_control of sendmsg().
When XDP is enabled on the TUN/TAP, TUN/TAP can process XDP inside a
loop without caring GUP thus it can do batch map flushing. When XDP is
not enabled or not supported, the underlayer socket need to build skb
and pass it to network core. The batched packet submission allows us
to do batching like netif_receive_skb_list() in the future.
This saves lots of indirect calls for better cache utilization. For
the case that we can't so batching e.g when sndbuf is limited or
packet size is too large, we will go for usual one packet per
sendmsg() way.
Doing testpmd on various setups gives us:
Test /+pps%
XDP_DROP on TAP /+44.8%
XDP_REDIRECT on TAP /+29%
macvtap (skb) /+26%
Netperf tests shows obvious improvements for small packet transmission:
size/session/+thu%/+normalize%
64/ 1/ +2%/ 0%
64/ 2/ +3%/ +1%
64/ 4/ +7%/ +5%
64/ 8/ +8%/ +6%
256/ 1/ +3%/ 0%
256/ 2/ +10%/ +7%
256/ 4/ +26%/ +22%
256/ 8/ +27%/ +23%
512/ 1/ +3%/ +2%
512/ 2/ +19%/ +14%
512/ 4/ +43%/ +40%
512/ 8/ +45%/ +41%
1024/ 1/ +4%/ 0%
1024/ 2/ +27%/ +21%
1024/ 4/ +38%/ +73%
1024/ 8/ +15%/ +24%
2048/ 1/ +10%/ +7%
2048/ 2/ +16%/ +12%
2048/ 4/ 0%/ +2%
2048/ 8/ 0%/ +2%
4096/ 1/ +36%/ +60%
4096/ 2/ -11%/ -26%
4096/ 4/ 0%/ +14%
4096/ 8/ 0%/ +4%
16384/ 1/ -1%/ +5%
16384/ 2/ 0%/ +2%
16384/ 4/ 0%/ -3%
16384/ 8/ 0%/ +4%
65535/ 1/ 0%/ +10%
65535/ 2/ 0%/ +8%
65535/ 4/ 0%/ +1%
65535/ 8/ 0%/ +3%
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement TUN_MSG_PTR msg_control type. This type allows
the caller to pass an array of XDP buffs to tuntap through ptr field
of the tun_msg_control. Tap will build skb through those XDP buffers.
This will avoid lots of indirect calls thus improves the icache
utilization and allows to do XDP batched flushing when doing XDP
redirection.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implement TUN_MSG_PTR msg_control type. This type allows
the caller to pass an array of XDP buffs to tuntap through ptr field
of the tun_msg_control. If an XDP program is attached, tuntap can run
XDP program directly. If not, tuntap will build skb and do a fast
receiving since part of the work has been done by vhost_net.
This will avoid lots of indirect calls thus improves the icache
utilization and allows to do XDP batched flushing when doing XDP
redirection.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces to a new tun/tap specific msg_control:
#define TUN_MSG_UBUF 1
#define TUN_MSG_PTR 2
struct tun_msg_ctl {
int type;
void *ptr;
};
This allows us to pass different kinds of msg_control through
sendmsg(). The first supported type is ubuf (TUN_MSG_UBUF) which will
be used by the existed vhost_net zerocopy code. The second is XDP
buff, which allows vhost_net to pass XDP buff to TUN. This could be
used to implement accepting an array of XDP buffs from vhost_net in
the following patches.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch split out XDP logic into a single function. This make it to
be reused by XDP batching path in the following patch.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we're sure not to go native XDP, there's no need for several things
like bh and rcu stuffs. So this patch introduces a helper to build skb
and hold page refcnt. When we found we will go through skb path, build
skb directly.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to duplicate page get logic in each action. So this
patch tries to get page and calculate the offset before processing XDP
actions (except for XDP_DROP), and undo them when meet errors (we
don't care the performance on errors). This will be used for factoring
out XDP logic.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the bh enabling a little bit earlier, this will be
used for factoring out the core XDP logic of tuntap.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new sock flag - SOCK_XDP. This will be used
for notifying the upper layer that XDP program is attached on the
lower socket, and requires for extra headroom.
TUN will be the first user.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
llc_sap_close() is called by llc_sap_put() which
could be called in BH context in llc_rcv(). We can't
block in BH.
There is no reason to block it here, kfree_rcu() should
be sufficient.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket option will be enabled by default to ensure current behaviour
is not changed. This is the same for the IPv4 version.
A socket bound to in6addr_any and a specific port will receive all traffic
on that port. Analogue to IP_MULTICAST_ALL, disable this behaviour, if
one or more multicast groups were joined (using said socket) and only
pass on multicast traffic from groups, which were explicitly joined via
this socket.
Without this option disabled a socket (system even) joined to multiple
multicast groups is very hard to get right. Filtering by destination
address has to take place in user space to avoid receiving multicast
traffic from other multicast groups, which might have traffic on the same
port.
The extension of the IP_MULTICAST_ALL socketoption to just apply to ipv6,
too, is not done to avoid changing the behaviour of current applications.
Signed-off-by: Andre Naujoks <nautsch2@gmail.com>
Acked-By: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hauke Mehrtens says:
====================
Add support for Lantiq / Intel vrx200 network
This adds basic support for the GSWIP (Gigabit Switch) found in the
VRX200 SoC.
There are different versions of this IP core used in different SoCs, but
this driver was currently only tested on the VRX200 SoC line, for other
SoCs this driver probably need some adoptions to work.
I also plan to add Layer 2 offloading to the DSA driver and later also
layer 3 offloading which is supported by the PPE HW block.
All these patches should go through the net-next tree.
This depends on the patch "MIPS: lantiq: dma: add dev pointer" which
should go into 4.19.
Changes since:
v2:
* Send patch "MIPS: lantiq: dma: add dev pointer" separately
* all: removed return in register write functions
* switch: uses phylink
* switch: uses hardware MDIO auto polling
* switch: use usleep_range() in MDIO busy check
* switch: configure MDIO bus to 2.5 MHz
* switch: disable xMII link when it is not used
* Ethernet: use NAPI for TX cleanups
* Ethernet: enable clock in open callback
* Ethernet: improve skb allocation
* Ethernet: use net_dev->stats
v1:
* Add "MIPS: lantiq: dma: add dev pointer"
* checkpatch fixes a all patches
* Added binding documentation
* use readx_poll_timeout function and ETIMEOUT error code
* integrate GPHY firmware loading into DSA driver
* renamed to NET_DSA_LANTIQ_GSWIP
* removed some needed casts
* added of_device_id.data information about the detected switch
* fixed John's email address
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.
The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.
The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the binding for the GSWIP (Gigabit switch) core found in the
xrx200 / VR9 Lantiq / Intel SoC.
This part takes care of the switch, MDIO bus, and loading the FW into
the embedded GPHYs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.
When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.
This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the binding for the PMAC core between the CPU and the GSWIP
switch found on the xrx200 / VR9 Lantiq / Intel SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: devicetree@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DMA channel is opened the IRQ should not get activated
automatically, this allows it to pull data out manually without the help
of interrupts. This is needed for a workaround in the vrx200 Ethernet
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document is stale, let's remove it.
Remove TCP congestion document.
Signed-off-by: Tobin C. Harding <me@tobin.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar with commit 72f6d71e49 ("vxlan: add ttl inherit support"),
currently ttl == 0 means "use whatever default value" on geneve instead
of inherit inner ttl. To respect compatibility with old behavior, let's
add a new IFLA_GENEVE_TTL_INHERIT for geneve ttl inherit support.
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=GbIW
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2018-09-12' of git://anongit.freedesktop.org/drm/drm
Pull drm nouveau fixes from Dave Airlie:
"I'm sending this separately as it's a bit larger than I generally like
for one driver, but it does contain a bunch of make my nvidia laptop
not die (runpm) and a bunch to make my docking station and monitor
display stuff (mst) fixes.
Lyude has spent a lot of time on these, and we are putting the fixes
into distro kernels as well asap, as it helps a bunch of standard
Lenovo laptops, so I'm fairly happy things are better than they were
before these patches, but I decided to split them out just for
clarification"
* tag 'drm-fixes-2018-09-12' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/disp/gm200-: enforce identity-mapped SOR assignment for LVDS/eDP panels
drm/nouveau/disp: fix DP disable race
drm/nouveau/disp: move eDP panel power handling
drm/nouveau/disp: remove unused struct member
drm/nouveau/TBDdevinit: don't fail when PMU/PRE_OS is missing from VBIOS
drm/nouveau/mmu: don't attempt to dereference vmm without valid instance pointer
drm/nouveau: fix oops in client init failure path
drm/nouveau: Fix nouveau_connector_ddc_detect()
drm/nouveau/drm/nouveau: Don't forget to cancel hpd_work on suspend/unload
drm/nouveau/drm/nouveau: Prevent handling ACPI HPD events too early
drm/nouveau: Reset MST branching unit before enabling
drm/nouveau: Only write DP_MSTM_CTRL when needed
drm/nouveau: Remove useless poll_enable() call in drm_load()
drm/nouveau: Remove useless poll_disable() call in switcheroo_set_state()
drm/nouveau: Remove useless poll_enable() call in switcheroo_set_state()
drm/nouveau: Fix deadlocks in nouveau_connector_detect()
drm/nouveau/drm/nouveau: Use pm_runtime_get_noresume() in connector_detect()
drm/nouveau/drm/nouveau: Fix deadlock with fb_helper with async RPM requests
drm/nouveau: Remove duplicate poll_enable() in pmops_runtime_suspend()
drm/nouveau/drm/nouveau: Fix bogus drm_kms_helper_poll_enable() placement
