Christoph Hellwig noticed that we were doing some unnecessary
work in orangefs_flush:
orangefs_flush just writes out data on every close(2) call. There is
no need to change anything about the dirty state, especially as
orangefs doesn't treat I_DIRTY_TIMES special in any way. The code
seems to come from partially open coding vfs_fsync.
He sent in a patch with the above commit message and also a
patch that was a reversion of another Orangefs patch I had
sent upstream a while ago. I had to fix his reversion patch
so that it would compile which caused his "don't mess with
I_DIRTY_TIMES" patch to fail to apply. So here I have just
remade his patch and applied it after the fixed reversion patch.
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Christoph Hellwig sent in a reversion of "orangefs: remember count
when reading." because:
->read_iter calls can race with each other and one or
more ->flush calls. Remove the the scheme to store the read
count in the file private data as is is completely racy and
can cause use after free or double free conditions
Christoph's reversion caused Orangefs not to work or to compile. I
added a patch that fixed that, but intel's kbuild test robot pointed
out that sending Christoph's patch followed by my patch upstream, it
would break bisection because of the failure to compile. So I have
combined the reversion plus my patch... here's the commit message
that was in my patch:
Logically, optimal Orangefs "pages" are 4 megabytes. Reading
large Orangefs files 4096 bytes at a time is like trying to
kick a dead whale down the beach. Before Christoph's "Revert
orangefs: remember count when reading." I tried to give users
a knob whereby they could, for example, use "count" in
read(2) or bs with dd(1) to get whatever they considered an
appropriate amount of bytes at a time from Orangefs and fill
as many page cache pages as they could at once.
Without the racy code that Christoph reverted Orangefs won't
even compile, much less work. So this replaces the logic that
used the private file data that Christoph reverted with
a static number of bytes to read from Orangefs.
I ran tests like the following to determine what a
reasonable static number of bytes might be:
dd if=/pvfsmnt/asdf of=/dev/null count=128 bs=4194304
dd if=/pvfsmnt/asdf of=/dev/null count=256 bs=2097152
dd if=/pvfsmnt/asdf of=/dev/null count=512 bs=1048576
.
.
.
dd if=/pvfsmnt/asdf of=/dev/null count=4194304 bs=128
Reads seem faster using the static number, so my "knob code"
wasn't just racy, it wasn't even a good idea...
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Reported-by: kbuild test robot <lkp@intel.com>
Merge vm fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/sparse: fix kernel crash with pfn_section_valid check
mm: fork: fix kernel_stack memcg stats for various stack implementations
hugetlb_cgroup: fix illegal access to memory
drivers/base/memory.c: indicate all memory blocks as removable
mm/swapfile.c: move inode_lock out of claim_swapfile
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns).
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl6AxjkTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoX7ED/9o8WQx1wmZ9B70FZYWkCBim4YX1GzW
IBNy5dNJKnfDyHQ7kUip5sr2V9RtTU1vTjfEF/dw4NlgFEbk8Z2K4KvraET0DX5v
UISL64TIl2lNhM0ey7WNX9XRxN2CG1FveAwRqKiTDQP9lla/DN7q7LyOGn8iBamB
ulCYY6Kp2uppA47XbbwITy3mDbKEGma8nAUNsF0sUcHxDq2BUUBwDdbgWuc6i7b3
nQa4eqvo2ZHQSkCze5/KAsz0MeBTULOzhtrrZ8SE8lEGyz0KLdymi8hneg0zXexP
yTJ/IKaP8kfL+yjcJJGBGvZsEbKdUurIMDBUl82955MUSBV0XbYUliiUVNk28n7k
7UsJPua69erHqWFKa4ucqGzURkUhHmpvNcRiOnZNMGuXKuV2t+CEfU1PLu/nVKos
MbRw9tSNJ4LDt9wmuJiV3o+xBEXW2QuIgWg1aSdvxdOfRrP4f8zkeojezMO0YO9O
plMKIlNoH2Xf0sfmMWGze2l/cqpqLgXPzF+e62+M9/wdJDBTLgTdUpFQq3qu46Lc
vWTTgmNIWO2UDTDKukCTITk/kI0AYtayAnNmcjvviGOO8ge2vlUaOxd6nEiF4y46
U7X9VffZODopxvjmKX/8tS9sB3cPb/vWqFND0jY4SZzx0SXQFRgPNXsARA+q/Fan
AqNrpL4auLlTlw==
=qZa/
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for the Hyper-V clocksource driver to make sched clock
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns)"
* tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/hyper-v: Make sched clock return nanoseconds correctly
-----BEGIN PGP SIGNATURE-----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=s1UQ
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single bugfix to prevent reference leaks in irq affinity notifiers"
* tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix reference leaks on irq affinity notifiers
Fix the crash like this:
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000c3447c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 11 PID: 7519 Comm: lt-ndctl Not tainted 5.6.0-rc7-autotest #1
...
NIP [c000000000c3447c] vmemmap_populated+0x98/0xc0
LR [c000000000088354] vmemmap_free+0x144/0x320
Call Trace:
section_deactivate+0x220/0x240
__remove_pages+0x118/0x170
arch_remove_memory+0x3c/0x150
memunmap_pages+0x1cc/0x2f0
devm_action_release+0x30/0x50
release_nodes+0x2f8/0x3e0
device_release_driver_internal+0x168/0x270
unbind_store+0x130/0x170
drv_attr_store+0x44/0x60
sysfs_kf_write+0x68/0x80
kernfs_fop_write+0x100/0x290
__vfs_write+0x3c/0x70
vfs_write+0xcc/0x240
ksys_write+0x7c/0x140
system_call+0x5c/0x68
The crash is due to NULL dereference at
test_bit(idx, ms->usage->subsection_map);
due to ms->usage = NULL in pfn_section_valid()
With commit d41e2f3bd5 ("mm/hotplug: fix hot remove failure in
SPARSEMEM|!VMEMMAP case") section_mem_map is set to NULL after
depopulate_section_mem(). This was done so that pfn_page() can work
correctly with kernel config that disables SPARSEMEM_VMEMMAP. With that
config pfn_to_page does
__section_mem_map_addr(__sec) + __pfn;
where
static inline struct page *__section_mem_map_addr(struct mem_section *section)
{
unsigned long map = section->section_mem_map;
map &= SECTION_MAP_MASK;
return (struct page *)map;
}
Now with SPASEMEM_VMEMAP enabled, mem_section->usage->subsection_map is
used to check the pfn validity (pfn_valid()). Since section_deactivate
release mem_section->usage if a section is fully deactivated,
pfn_valid() check after a subsection_deactivate cause a kernel crash.
static inline int pfn_valid(unsigned long pfn)
{
...
return early_section(ms) || pfn_section_valid(ms, pfn);
}
where
static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
{
int idx = subsection_map_index(pfn);
return test_bit(idx, ms->usage->subsection_map);
}
Avoid this by clearing SECTION_HAS_MEM_MAP when mem_section->usage is
freed. For architectures like ppc64 where large pages are used for
vmmemap mapping (16MB), a specific vmemmap mapping can cover multiple
sections. Hence before a vmemmap mapping page can be freed, the kernel
needs to make sure there are no valid sections within that mapping.
Clearing the section valid bit before depopulate_section_memap enables
this.
[aneesh.kumar@linux.ibm.com: add comment]
Link: http://lkml.kernel.org/r/20200326133235.343616-1-aneesh.kumar@linux.ibm.comLink: http://lkml.kernel.org/r/20200325031914.107660-1-aneesh.kumar@linux.ibm.com
Fixes: d41e2f3bd5 ("mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depending on CONFIG_VMAP_STACK and the THREAD_SIZE / PAGE_SIZE ratio the
space for task stacks can be allocated using __vmalloc_node_range(),
alloc_pages_node() and kmem_cache_alloc_node().
In the first and the second cases page->mem_cgroup pointer is set, but
in the third it's not: memcg membership of a slab page should be
determined using the memcg_from_slab_page() function, which looks at
page->slab_cache->memcg_params.memcg . In this case, using
mod_memcg_page_state() (as in account_kernel_stack()) is incorrect:
page->mem_cgroup pointer is NULL even for pages charged to a non-root
memory cgroup.
It can lead to kernel_stack per-memcg counters permanently showing 0 on
some architectures (depending on the configuration).
In order to fix it, let's introduce a mod_memcg_obj_state() helper,
which takes a pointer to a kernel object as a first argument, uses
mem_cgroup_from_obj() to get a RCU-protected memcg pointer and calls
mod_memcg_state(). It allows to handle all possible configurations
(CONFIG_VMAP_STACK and various THREAD_SIZE/PAGE_SIZE values) without
spilling any memcg/kmem specifics into fork.c .
Note: This is a special version of the patch created for stable
backports. It contains code from the following two patches:
- mm: memcg/slab: introduce mem_cgroup_from_obj()
- mm: fork: fix kernel_stack memcg stats for various stack implementations
[guro@fb.com: introduce mem_cgroup_from_obj()]
Link: http://lkml.kernel.org/r/20200324004221.GA36662@carbon.dhcp.thefacebook.com
Fixes: 4d96ba3530 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200303233550.251375-1-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This appears to be a mistake in commit faced7e080 ("mm: hugetlb
controller for cgroups v2").
Essentially that commit does a hugetlb_cgroup_from_counter assuming that
page_counter_try_charge has initialized counter.
But if that has failed then it seems will not initialize counter, so
hugetlb_cgroup_from_counter(counter) ends up pointing to random memory,
causing kasan to complain.
The solution is to simply use 'h_cg', instead of
hugetlb_cgroup_from_counter(counter), since that is a reference to the
hugetlb_cgroup anyway. After this change kasan ceases to complain.
Fixes: faced7e080 ("mm: hugetlb controller for cgroups v2")
Reported-by: syzbot+cac0c4e204952cf449b1@syzkaller.appspotmail.com
Signed-off-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Giuseppe Scrivano <gscrivan@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/20200313223920.124230-1-almasrymina@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We see multiple issues with the implementation/interface to compute
whether a memory block can be offlined (exposed via
/sys/devices/system/memory/memoryX/removable) and would like to simplify
it (remove the implementation).
1. It runs basically lockless. While this might be good for performance,
we see possible races with memory offlining that will require at
least some sort of locking to fix.
2. Nowadays, more false positives are possible. No arch-specific checks
are performed that validate if memory offlining will not be denied
right away (and such check will require locking). For example, arm64
won't allow to offline any memory block that was added during boot -
which will imply a very high error rate. Other archs have other
constraints.
3. The interface is inherently racy. E.g., if a memory block is detected
to be removable (and was not a false positive at that time), there is
still no guarantee that offlining will actually succeed. So any
caller already has to deal with false positives.
4. It is unclear which performance benefit this interface actually
provides. The introducing commit 5c755e9fd8 ("memory-hotplug: add
sysfs removable attribute for hotplug memory remove") mentioned
"A user-level agent must be able to identify which sections
of memory are likely to be removable before attempting the
potentially expensive operation."
However, no actual performance comparison was included.
Known users:
- lsmem: Will group memory blocks based on the "removable" property. [1]
- chmem: Indirect user. It has a RANGE mode where one can specify
removable ranges identified via lsmem to be offlined. However,
it also has a "SIZE" mode, which allows a sysadmin to skip the
manual "identify removable blocks" step. [2]
- powerpc-utils: Uses the "removable" attribute to skip some memory
blocks right away when trying to find some to offline+remove.
However, with ballooning enabled, it already skips this
information completely (because it once resulted in many false
negatives). Therefore, the implementation can deal with false
positives properly already. [3]
According to Nathan Fontenot, DLPAR on powerpc is nowadays no longer
driven from userspace via the drmgr command (powerpc-utils). Nowadays
it's managed in the kernel - including onlining/offlining of memory
blocks - triggered by drmgr writing to /sys/kernel/dlpar. So the
affected legacy userspace handling is only active on old kernels. Only
very old versions of drmgr on a new kernel (unlikely) might execute
slower - totally acceptable.
With CONFIG_MEMORY_HOTREMOVE, always indicating "removable" should not
break any user space tool. We implement a very bad heuristic now.
Without CONFIG_MEMORY_HOTREMOVE we cannot offline anything, so report
"not removable" as before.
Original discussion can be found in [4] ("[PATCH RFC v1] mm:
is_mem_section_removable() overhaul").
Other users of is_mem_section_removable() will be removed next, so that
we can remove is_mem_section_removable() completely.
[1] http://man7.org/linux/man-pages/man1/lsmem.1.html
[2] http://man7.org/linux/man-pages/man8/chmem.8.html
[3] https://github.com/ibm-power-utilities/powerpc-utils
[4] https://lkml.kernel.org/r/20200117105759.27905-1-david@redhat.com
Also, this patch probably fixes a crash reported by Steve.
http://lkml.kernel.org/r/CAPcyv4jpdaNvJ67SkjyUJLBnBnXXQv686BiVW042g03FUmWLXw@mail.gmail.com
Reported-by: "Scargall, Steve" <steve.scargall@intel.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Nathan Fontenot <ndfont@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200128093542.6908-1-david@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
claim_swapfile() currently keeps the inode locked when it is successful,
or the file is already swapfile (with -EBUSY). And, on the other error
cases, it does not lock the inode.
This inconsistency of the lock state and return value is quite confusing
and actually causing a bad unlock balance as below in the "bad_swap"
section of __do_sys_swapon().
This commit fixes this issue by moving the inode_lock() and IS_SWAPFILE
check out of claim_swapfile(). The inode is unlocked in
"bad_swap_unlock_inode" section, so that the inode is ensured to be
unlocked at "bad_swap". Thus, error handling codes after the locking now
jumps to "bad_swap_unlock_inode" instead of "bad_swap".
=====================================
WARNING: bad unlock balance detected!
5.5.0-rc7+ #176 Not tainted
-------------------------------------
swapon/4294 is trying to release lock (&sb->s_type->i_mutex_key) at: __do_sys_swapon+0x94b/0x3550
but there are no more locks to release!
other info that might help us debug this:
no locks held by swapon/4294.
stack backtrace:
CPU: 5 PID: 4294 Comm: swapon Not tainted 5.5.0-rc7-BTRFS-ZNS+ #176
Hardware name: ASUS All Series/H87-PRO, BIOS 2102 07/29/2014
Call Trace:
dump_stack+0xa1/0xea
print_unlock_imbalance_bug.cold+0x114/0x123
lock_release+0x562/0xed0
up_write+0x2d/0x490
__do_sys_swapon+0x94b/0x3550
__x64_sys_swapon+0x54/0x80
do_syscall_64+0xa4/0x4b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f15da0a0dc7
Fixes: 1638045c36 ("mm: set S_SWAPFILE on blockdev swap devices")
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Qais Youef <qais.yousef@arm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200206090132.154869-1-naohiro.aota@wdc.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix memory leak in vti6, from Torsten Hilbrich.
2) Fix double free in xfrm_policy_timer, from YueHaibing.
3) NL80211_ATTR_CHANNEL_WIDTH attribute is put with wrong type, from
Johannes Berg.
4) Wrong allocation failure check in qlcnic driver, from Xu Wang.
5) Get ks8851-ml IO operations right, for real this time, from Marek
Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (22 commits)
r8169: fix PHY driver check on platforms w/o module softdeps
net: ks8851-ml: Fix IO operations, again
mlxsw: spectrum_mr: Fix list iteration in error path
qlcnic: Fix bad kzalloc null test
mac80211: set IEEE80211_TX_CTRL_PORT_CTRL_PROTO for nl80211 TX
mac80211: mark station unauthorized before key removal
mac80211: Check port authorization in the ieee80211_tx_dequeue() case
cfg80211: Do not warn on same channel at the end of CSA
mac80211: drop data frames without key on encrypted links
ieee80211: fix HE SPR size calculation
nl80211: fix NL80211_ATTR_CHANNEL_WIDTH attribute type
xfrm: policy: Fix doulbe free in xfrm_policy_timer
bpf: Explicitly memset some bpf info structures declared on the stack
bpf: Explicitly memset the bpf_attr structure
bpf: Sanitize the bpf_struct_ops tcp-cc name
vti6: Fix memory leak of skb if input policy check fails
esp: remove the skb from the chain when it's enqueued in cryptd_wq
ipv6: xfrm6_tunnel.c: Use built-in RCU list checking
xfrm: add the missing verify_sec_ctx_len check in xfrm_add_acquire
xfrm: fix uctx len check in verify_sec_ctx_len
...
Pull i2c fixes from Wolfram Sang:
"Three more driver bugfixes, and two doc improvements fixing build
warnings while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: pca-platform: Use platform_irq_get_optional
i2c: st: fix missing struct parameter description
i2c: nvidia-gpu: Handle timeout correctly in gpu_i2c_check_status()
i2c: fix a doc warning
i2c: hix5hd2: add missed clk_disable_unprepare in remove
Two small fixes, one in drivers (qla2xxx) and one in the core (sd) to
try to cope with USB enclosures that silently change reported
parameters.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXn9r4CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishcRAAQCoW8Q2
raOl/SkEJ9CrqAsuav4B4HPl+B08wno3lHnp6wEA5Tkiw1aCLjqPBx/k0FctlRaD
wQIxxBD8dy47cFV/qfo=
=tWW/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes: one in drivers (qla2xxx), and one in the core (sd) to
try to cope with USB enclosures that silently change reported
parameters"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix optimal I/O size for devices that change reported values
scsi: qla2xxx: Fix I/Os being passed down when FC device is being deleted
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform 22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Daniel Borkmann says:
====================
pull-request: bpf 2020-03-27
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 4 day(s) which contain
a total of 4 files changed, 25 insertions(+), 20 deletions(-).
The main changes are:
1) Explicitly memset the bpf_attr structure on bpf() syscall to avoid
having to rely on compiler to do so. Issues have been noticed on
some compilers with padding and other oddities where the request was
then unexpectedly rejected, from Greg Kroah-Hartman.
2) Sanitize the bpf_struct_ops TCP congestion control name in order to
avoid problematic characters such as whitespaces, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f325937735 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-03-27
1) Handle NETDEV_UNREGISTER for xfrm device to handle asynchronous
unregister events cleanly. From Raed Salem.
2) Fix vti6 tunnel inter address family TX through bpf_redirect().
From Nicolas Dichtel.
3) Fix lenght check in verify_sec_ctx_len() to avoid a
slab-out-of-bounds. From Xin Long.
4) Add a missing verify_sec_ctx_len check in xfrm_add_acquire
to avoid a possible out-of-bounds to access. From Xin Long.
5) Use built-in RCU list checking of hlist_for_each_entry_rcu
to silence false lockdep warning in __xfrm6_tunnel_spi_lookup
when CONFIG_PROVE_RCU_LIST is enabled. From Madhuparna Bhowmik.
6) Fix a panic on esp offload when crypto is done asynchronously.
From Xin Long.
7) Fix a skb memory leak in an error path of vti6_rcv.
From Torsten Hilbrich.
8) Fix a race that can lead to a doulbe free in xfrm_policy_timer.
From Xin Long.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and a
few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the timings
for the NAND flash on the Nokia N900 that regressed a while ago after
the move to configuring them from DT. Some other OMAPs now set the
correct dma limits on the L3 bus, and a regression fix addresses lost
Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel
power supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC,
this is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data when
mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver
-----BEGIN PGP SIGNATURE-----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=31+Z
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT and driver fixes from Arnd Bergmann:
"For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and
a few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the
timings for the NAND flash on the Nokia N900 that regressed a while
ago after the move to configuring them from DT. Some other OMAPs
now set the correct dma limits on the L3 bus, and a regression fix
addresses lost Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel power
supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC, this
is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data
when mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver"
* tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
soc: samsung: chipid: Fix return value on non-Exynos platforms
arm64: dts: Fix leftover entry-methods for PSCI
ARM: dts: exynos: Fix regulator node aliasing on Midas-based boards
ARM: dts: oxnas: Fix clear-mask property
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
soc: fsl: dpio: register dpio irq handlers after dpio create
tee: amdtee: out of bounds read in find_session()
ARM: dts: N900: fix onenand timings
bus: ti-sysc: Fix quirk flags for lcdc on am335x
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
...
Sorry for the last minute patches, but a few things fell through the cracks
recently. I was on the fence about sending a late PR just for the M-mode
fixes, as we don't really have any users, but the last patch fixes the build
for Fedora which I consider pretty important. Given that the M-mode fixes
should be very low risk, I figured it's worth sending them along as well.
This passes my standard "boot in QEMU" test.
-----BEGIN PGP SIGNATURE-----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=ech4
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"Sorry for the last minute patches, but a few things fell through the
cracks recently. I was on the fence about sending a late pull request
just for the M-mode fixes, as we don't really have any users, but the
last patch fixes the build for Fedora which I consider pretty
important.
Given that the M-mode fixes should be very low risk, I figured it's
worth sending them along as well.
Thhis passes my standard 'boot in QEMU' test"
* tag 'riscv-for-linus-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Move all address space definition macros to one place
RISC-V: Only select essential drivers for SOC_VIRT config
riscv: fix the IPI missing issue in nommu mode
riscv: uaccess should be used in nommu mode
A single fix for building dtc with GCC 10.
-----BEGIN PGP SIGNATURE-----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=HNrU
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull Devicetree fix from Rob Herring:
"A single fix for building dtc with GCC 10"
* tag 'devicetree-fixes-for-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
scripts/dtc: Remove redundant YYLOC global declaration
- Fix defconfig build when using Clang's integrated assembler
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl592dUQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNKUFCACQw9B0AHizig0dzL+jAw3fZApcjTWGzmv8
Blb0BtdYcEYcMvrbNnc21nDAghUw3lt4ncqbjcd6H9+jISN+D5yMTooqBOa6N7eG
3bGEsap7QsxdqbiFdyPB7woyTa8PR+YSmg9eCtKVX82R2HuPZar69RhDFi1D/iSn
lbt2ltVTfMTuzEETHoCoixn3r+BFu5HHaFx6JuK6bOT29WpXmdseB8NhkuVE3kEu
O1nUFW69vGpQvalwYrspd5CSiyT9BuFP9vqz9xYQVCwWLN+O5VuGLoF264SHKVKM
O4qk18Vu/LG0hU/2V/xBcPQ4CMc9BsR3Z8AyqdfULgBWjqGQf396
=TROL
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix defconfig build when using Clang's integrated assembler"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: alternative: fix build with clang integrated assembler
fixing the parents of a few clks and making KASAN happy with how the
message passing code works. Besides that we have a TI driver fix for the
RTC parent and a fix for the basic gate type registration functions
introduced this release where they didn't actually pass the arguments in
the right places to the multiplexer function down below.
-----BEGIN PGP SIGNATURE-----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=adIQ
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes.
Mostly they're around the i.MX drivers fixing the parents of a few
clks and making KASAN happy with how the message passing code works.
Besides that we have a TI driver fix for the RTC parent and a fix for
the basic gate type registration functions introduced this release
where they didn't actually pass the arguments in the right places to
the multiplexer function down below"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: imx: Align imx sc clock parent msg structs to 4
clk: imx: Align imx sc clock msg structs to 4
clk: Pass correct arguments to __clk_hw_register_gate()
clk: ti: am43xx: Fix clock parent for RTC clock
clk: imx8mp: Correct the enet_qos parent clock
clk: imx8mp: Correct IMX8MP_CLK_HDMI_AXI clock parent
radeon/amdgpu/dma-buf:
- sg list fixes
scheduler:
- oops fix
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJefaN4AAoJEAx081l5xIa+eakQAJYLuWSybs1/FwUybqnuv1BF
c9EiMf1XPt78wTM5hVI/7xv/0ZUW++p3FkioSKUxYWejDcZCZ16gVUw2Byh/eBWl
OIcVgjDZTO7z14/fgApqYjWrmmftwfg59LOvc44pZXNHyTIgJMCEbidTQy5dj7xW
NqWXXOokhgZPYZI2fAlkk9PVkSc9QaJTJCiWh8lSR4smQRHjF5uiiwwvYY3h33Nk
5hpH95kgHU6npke1t0EXrGdJtq1tdwDeqUoGkWNwWxQ405mPyBan7zC4zzSKJjbH
UKO+TaFJQQ2ycXTmgVx2KRpIOQa6g2vBYKVs98EylgO32P443D8nIUI4foDO7GY2
31rwK7GZfHTLWCOfFMNM4V+8dEwZJZYpbLOIc/4+zaufzBLwntLDZM/O9Dky9UU4
ZQKfFU4Q16Cy8ceVVdFmBn8fv+/Zn6wFewT4qXDtsuekjnD+HCCP7p5dxIGOBn89
SOoEH8b77TqnGEqJxf/XTeXIMvd2O3ZLeszMQyI4v/2YQzH+DkFY6OUchP6YwaCv
9/93T/e0sq7a6C18B9x70sTfAeGuza3R1BYd1RoCyDdn2H103i7Fm/E8Pu0JXOep
4GxU8GpGvaP2akZsB5WIcVz6ADaDPGtZvL/uooCans+LixgQMaGAAWgF97DWMjd7
B+g7bFio8qYqD+BIp6Sy
=ukHW
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2020-03-27' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Pretty quiet: some minor sg mapping fixes for 3 drivers, and a single
oops fix for the scheduler. I'm hoping nobody tries to send me a fixes
pull today but I'll keep an eye out of the weekend.
radeon/amdgpu/dma-buf:
- sg list fixes
scheduler:
- oops fix"
* tag 'drm-fixes-2020-03-27' of git://anongit.freedesktop.org/drm/drm:
drm/scheduler: fix rare NULL ptr race
drm/radeon: fix scatter-gather mapping with user pages
drm/amdgpu: fix scatter-gather mapping with user pages
drm/prime: use dma length macro when mapping sg
gcc 10 will default to -fno-common, which causes this error at link
time:
(.text+0x0): multiple definition of `yylloc'; dtc-lexer.lex.o (symbol from plugin):(.text+0x0): first defined here
This is because both dtc-lexer as well as dtc-parser define the same
global symbol yyloc. Before with -fcommon those were merged into one
defintion. The proper solution would be to to mark this as "extern",
however that leads to:
dtc-lexer.l:26:16: error: redundant redeclaration of 'yylloc' [-Werror=redundant-decls]
26 | extern YYLTYPE yylloc;
| ^~~~~~
In file included from dtc-lexer.l:24:
dtc-parser.tab.h:127:16: note: previous declaration of 'yylloc' was here
127 | extern YYLTYPE yylloc;
| ^~~~~~
cc1: all warnings being treated as errors
which means the declaration is completely redundant and can just be
dropped.
Signed-off-by: Dirk Mueller <dmueller@suse.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[robh: cherry-pick from upstream]
Cc: stable@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull input fixes from Dmitry Torokhov:
- a fix to generate proper timestamps on key autorepeat events that
were broken recently
- a fix for Synaptics driver to only activate reduced reporting mode
when explicitly requested
- a new keycode for "selective screenshot" function
- other assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix stale timestamp on key autorepeat events
Input: move the new KEY_SELECTIVE_SCREENSHOT keycode
Input: avoid BIT() macro usage in the serio.h UAPI header
Input: synaptics-rmi4 - set reduced reporting mode only when requested
Input: synaptics - enable RMI on HP Envy 13-ad105ng
Input: allocate keycode for "Selective Screenshot" key
Input: tm2-touchkey - add support for Coreriver TC360 variant
dt-bindings: input: add Coreriver TC360 binding
dt-bindings: vendor-prefixes: Add Coreriver vendor prefix
Input: raydium_i2c_ts - fix error codes in raydium_i2c_boot_trigger()
This patch reverts 5829210483 ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 5829210483 ("net: ks8851-ml: Fix 16-bit IO operation")
Fixes: edacb098ea ("net: ks8851-ml: Fix 16-bit data access")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get the following compilation error if CONFIG_SPARSEMEM_VMEMMAP is set.
---------------------------------------------------------------
./arch/riscv/include/asm/pgtable-64.h: In function ‘pud_page’:
./include/asm-generic/memory_model.h:54:29: error: ‘vmemmap’ undeclared
(first use in this function); did you mean ‘mem_map’?
#define __pfn_to_page(pfn) (vmemmap + (pfn))
^~~~~~~
./include/asm-generic/memory_model.h:82:21: note: in expansion of
macro ‘__pfn_to_page’
#define pfn_to_page __pfn_to_page
^~~~~~~~~~~~~
./arch/riscv/include/asm/pgtable-64.h:70:9: note: in expansion of macro
‘pfn_to_page’
return pfn_to_page(pud_val(pud) >> _PAGE_PFN_SHIFT);
---------------------------------------------------------------
Fix the compliation errors by moving all the address space definition
macros before including pgtable-64.h.
Fixes: 8ad8b72721 (riscv: Add KASAN support)
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We need to refresh timestamp when emitting key autorepeat events, otherwise
they will carry timestamp of the original key press event.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206929
Fixes: 3b51c44bd6 ("Input: allow drivers specify timestamp for input events")
Cc: stable@vger.kernel.org
Reported-by: teika kazura <teika@gmx.com>
Tested-by: teika kazura <teika@gmx.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When it's probing all of a fileserver's interfaces to find which one is
best to use, afs_do_probe_fileserver() takes a lock on the server record
and notes the pointer to the address list.
It doesn't, however, pin the address list, so as soon as it drops the
lock, there's nothing to stop the address list from being freed under
us.
Fix this by taking a ref on the address list inside the locked section
and dropping it at the end of the function.
Fixes: 3bf0fb6f33 ("afs: Probe multiple fileservers simultaneously")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
leak fixes, marked for stable.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEydHwtzie9C7TfviiSn/eOAIR84sFAl59DCwTHGlkcnlvbW92
QGdtYWlsLmNvbQAKCRBKf944AhHzi5oGB/943a7gIBV52PD3MGCnI8RWjgHkk3d0
en2JNI6i7hf7GD7GplMGkc0D8INBJhCZo1mwzX36QXYA3BeXKARkNXvEE+AZ4dX5
XbUiPE5WuUwxcT9sE9rTiCurx1ToN/XUlA27Vbt9J67U08w5BjJ3utO1LuW7z2ME
NPx6aw6tdwIEeNJBo4ge8y9vPKevtXqhkCbzSb2kn+tMhoMPuJ3RIj8kWIF7mYWZ
ofwOFoDnOfQuH+9ZA/mT4jL7ifR0am5QptHSD9kxge2mKlc0pmoABZK6sWNPOslg
jQaEiefH77K/IxRyAsQNM7iHbUzKpZGbqAHx92MU0redUjUWNdCDGUmF
=c01Y
-----END PGP SIGNATURE-----
Merge tag 'ceph-for-5.6-rc8' of git://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch for a rather old regression in fullness handling and two
memory leak fixes, marked for stable"
* tag 'ceph-for-5.6-rc8' of git://github.com/ceph/ceph-client:
ceph: fix memory leak in ceph_cleanup_snapid_map()
libceph: fix alloc_msg_with_page_vector() memory leaks
ceph: check POOL_FLAG_FULL/NEARFULL in addition to OSDMAP_FULL/NEARFULL
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl58ewEUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMpagf/Ya2j9EGWMv+0BSvV9POYjbMmxfOe
HdNld2zlaNreAvgHQvdW76AufIa+VnJqJEgI2wjN7exmC+HjqtF/uC9l5B3ZK5BR
WKK/t9ZynXhBSmrddLI477nufsv8c34lELgLObKMECGrzsGdx8T4tEg7q9GjlZBY
umDVc6kx0GEblzAIzX9Z8l8deFXeykTghMM+mSnHNDLd3a2L6hHoT4atDj5VcqQ/
PxpOV+uZhOliOgTaUmuvlQQUJ/CjJO2lsMoItGzUtKb6gTKKc0U/5kuGxXe7phB+
Ttz9Svs2oLBrKcr59R5UfI7ovGqPCaXgQ4cRPwBgIQ4lS/LR4s5ltODywA==
=wIQr
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"x86 bug fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: X86: Narrow down the IPI fastpath to single target IPI
KVM: LAPIC: Also cancel preemption timer when disarm LAPIC timer
KVM: VMX: don't allow memory operands for inline asm that modifies SP
KVM: LAPIC: Mark hrtimer for period or oneshot mode to expire in hard interrupt context
KVM: SVM: Issue WBINVD after deactivating an SEV guest
KVM: SVM: document KVM_MEM_ENCRYPT_OP, let userspace detect if SEV is available
KVM: x86: remove bogus user-triggerable WARN_ON
Testing 'parse-maintainers' due to the previous commit shows a bad file
pattern for the "TI VPE/CAL DRIVERS" entry in the MAINTAINERS file.
There's also a lot of mis-ordered entries, but I'm still a bit nervous
about the inevitable and annoying merge problems it would probably cause
to fix them up.
The MAINTAINERS file is one of my least favorite files due to being huge
and centralized, but fixing it is also horribly painful for that reason.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an --order switch to control section reordering.
Default for --order is off.
Change the default ordering to a slightly more sensible:
M: Person acting as a maintainer
R: Person acting as a patch reviewer
L: Mailing list where patches should be sent
S: Maintenance status
W: URI for general information
Q: URI for patchwork tracking
B: URI for bug tracking/submission
C: URI for chat
P: URI or file for subsystem specific coding styles
T: SCM tree type and location
F: File and directory pattern
X: File and directory exclusion pattern
N: File glob
K: Keyword - patch content regex
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should try to keep keycodes sequential unless there is a reason to leave
a gap in numbering, so let's move it from 0x280 to 0x27a while we still
can.
Fixes: 3b059da983 ("Input: allocate keycode for Selective Screenshot key")
Acked-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200326182711.GA259753@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The kconfig select causes build failues for SOC_VIRT config becaus
we are selecting lot of VIRTIO drivers without selecting all required
dependencies.
Better approach is to only select essential drivers from SOC_VIRT
config option and enable required VIRTIO drivers using defconfigs.
Fixes: 759bdc1681 ("RISC-V: Add kconfig option for QEMU virt machine")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
* drop data packets if there's no key for them anymore, after
there had been one, to avoid sending them in clear when
hostapd removes the key before it removes the station and
the packets are still queued
* check port authorization again after dequeue, to avoid
sending packets if the station is no longer authorized
* actually remove the authorization flag before the key so
packets are also dropped properly because of this
* fix nl80211 control port packet tagging to handle them as
packets allowed to go out without encryption
* fix NL80211_ATTR_CHANNEL_WIDTH outgoing netlink attribute
width (should be 32 bits, not 8)
* don't WARN in a CSA scenario that happens on some APs
* fix HE spatial reuse element size calculation
-----BEGIN PGP SIGNATURE-----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=pnuh
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2020-03-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
We have the following fixes:
* drop data packets if there's no key for them anymore, after
there had been one, to avoid sending them in clear when
hostapd removes the key before it removes the station and
the packets are still queued
* check port authorization again after dequeue, to avoid
sending packets if the station is no longer authorized
* actually remove the authorization flag before the key so
packets are also dropped properly because of this
* fix nl80211 control port packet tagging to handle them as
packets allowed to go out without encryption
* fix NL80211_ATTR_CHANNEL_WIDTH outgoing netlink attribute
width (should be 32 bits, not 8)
* don't WARN in a CSA scenario that happens on some APs
* fix HE spatial reuse element size calculation
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_entry_from_reverse() iterates backwards over the list from
the current position, but in the error path we should start from the
previous position.
Fix this by using list_for_each_entry_continue_reverse() instead.
This suppresses the following error from coccinelle:
drivers/net/ethernet/mellanox/mlxsw//spectrum_mr.c:655:34-38: ERROR:
invalid reference to the index variable of the iterator on line 636
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qlcnic_83xx_get_reset_instruction_template, the variable
of null test is bad, so correct it.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Several MAINTAINERS updates
- Memory leak regression in ODP
- Several fixes for syzkaller related crashes. Google recently taught
syzkaller to create the software RDMA devices
- Crash fixes for HFI1
- Several fixes for mlx5 crashes
- Prevent unprivileged access to an unsafe mlx5 HW resource
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEfB7FMLh+8QxL+6i3OG33FX4gmxoFAl57oakACgkQOG33FX4g
mxqLQBAAgjBxExYAK51ImMoCOXlZ9uInoACes8+e1HjIJUPhS3/WVubCMXJxAYrc
x7xtW7DUVBjNBYdQajgzWsDRrENovTq4rPscIWVSqTffWkYYubJbGXeBKTa045J6
3rsKL5Kzd0XGN0/XrXjctXpADEvEb1mjUjEMvsVmggIHneLJ5JgUdRTISwlsntmD
BbFo67DsSmQqOCx5B1az3l/RYPuWeFEYgQOAcWUC/rzsFEvEkmdqDr6FcbtkTWe1
pSqSTVQ6knDTvadwjwbpJRJg9SR/X4cHtGLOy1sP8HQ6Do671cAtFrusLb4Zf+w6
ncOll8/YPjiTe9fkTCX4Gdhn278t8cZAn2W9vrzPF8lv8tGRtlO5nXdR044NmBst
CBid7JaxzGVq0QhEEiWpV72Q8O7wQ5mARHR2x/zR2A/fdD+lqN1rjfDAqldrgYWV
5D+IFRwwwp9J+Y1pQAmTkzixItraRLD6jjzYG+qk5zopUnHBJBk67wZpWcS1zlER
SJuG0ztYn5KBSjoTGzOXfPIXpe+N3UhWxHx5P17G7UhRjbLE6oaij3TY7et/Bfj/
7esEQCLDyzEQdXJHNojyUKuyUU88N1yAC9gQbgHWPrrJBa/Ibxukq5O8dwDBpX8g
zOtSrv9i9r8g7RrKccxy0BUkrq+0OSttSopE+ssnRFTiVX3sMX0=
=RhVe
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"A small set of late-rc patches, mostly fixes for various crashers,
some syzkaller fixes and a mlx5 HW limitation:
- Several MAINTAINERS updates
- Memory leak regression in ODP
- Several fixes for syzkaller related crashes. Google recently taught
syzkaller to create the software RDMA devices
- Crash fixes for HFI1
- Several fixes for mlx5 crashes
- Prevent unprivileged access to an unsafe mlx5 HW resource"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Block delay drop to unprivileged users
RDMA/mlx5: Fix access to wrong pointer while performing flush due to error
RDMA/core: Ensure security pkey modify is not lost
MAINTAINERS: Clean RXE section and add Zhu as RXE maintainer
IB/hfi1: Ensure pq is not left on waitlist
IB/rdmavt: Free kernel completion queue when done
RDMA/mad: Do not crash if the rdma device does not have a umad interface
RDMA/core: Fix missing error check on dev_set_name()
RDMA/nl: Do not permit empty devices names during RDMA_NLDEV_CMD_NEWLINK/SET
RDMA/mlx5: Fix the number of hwcounters of a dynamic counter
MAINTAINERS: Update maintainers for HISILICON ROCE DRIVER
RDMA/odp: Fix leaking the tgid for implicit ODP
When a frame is transmitted via the nl80211 TX rather than as a
normal frame, IEEE80211_TX_CTRL_PORT_CTRL_PROTO wasn't set and
this will lead to wrong decisions (rate control etc.) being made
about the frame; fix this.
Fixes: 9118064914 ("mac80211: Add support for tx_control_port")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200326155333.f183f52b02f0.I4054e2a8c11c2ddcb795a0103c87be3538690243@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211 used to check port authorization in the Data frame enqueue case
when going through start_xmit(). However, that authorization status may
change while the frame is waiting in a queue. Add a similar check in the
dequeue case to avoid sending previously accepted frames after
authorization change. This provides additional protection against
potential leaking of frames after a station has been disconnected and
the keys for it are being removed.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200326155133.ced84317ea29.I34d4c47cd8cc8a4042b38a76f16a601fbcbfd9b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When cfg80211_update_assoc_bss_entry() is called, there is a
verification that the BSS channel actually changed. As some APs use
CSA also for bandwidth changes, this would result with a kernel
warning.
Fix this by removing the WARN_ON().
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.96316ada0e8d.I6710376b1b4257e5f4712fc7ab16e2b638d512aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
