Set the request->is_last to each stream request to indicate that the
request is the last stream request of a transfer. The DWC3 controller
needs to know this info to properly switch streams. The current
implementation of f_tcm uses a single request per transfer, so every
stream request is the last of its stream.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC_usb32 supports MDWIDTH value larger than 255 and up to 1023. The
field HWPARAMS6[9:8] stores the upper 2-bit values of the DWC_usb32's
MDWIDTH. Check that parameter and properly get the MDWIDTH for
DWC_usb32.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Synopsys introduces a new controller DWC_usb32. It supports dual-lane
and speed up to 20 Gbps, and the DWC3 driver will drive this controller.
Currently the driver uses a single field dwc->revision to ID both
DWC_usb3 and DWC_usb31 and their version number. This was sufficient for
two IPs, but this method doesn't work with additional IPs. As a result,
let's separate the dwc->revision field to 2 separate fields: ip and
revision. The ip field now stores the ID of the controller's IP while
the revision field stores the controller's version number.
This new scheme enforces DWC3 to compare the revision within the same IP
only. As a result, we must update all the revision check of the
controller to check its corresponding IP.
To help with this enforcement, we create a few macros to help with
the common version checks:
DWC3_IP_IS(IP)
DWC3_VER_IS(IP, VERSION)
DWC3_VER_IS_PRIOR(IP, VERSION)
DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION)
DWC3_VER_TYPE_IS_WITHIN(IP, VERSION,
LOWER_VERSION_TYPE,
UPPER_VERSION_TYPE)
The DWC_usb32 controller operates using the same programming model and
with very similar configurations as its previous controllers. Please
note that the various IP and revision checks in this patch match the
current checks for DWC_usb31 version 1.90a. Additional configurations
that are unique to DWC_usb32 are applied separately.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
OTG port on Tegra194 supports GEN1 speeds when in device mode and GEN2
speeds when in host mode. dd port_speed_quirk that configures port to
GEN1/GEN2 speds, corresponding to the mode.
Based on work by WayneChang <waynec@nvidia.com>
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This commit adds support for XUSB device mode controller support on
Tegra194 SoC. This is very similar to the existing Tegra186 XUDC, with lpm
support added in addition.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Sparse reports a warning at set_link_state()
warning: context imbalance in set_link_state() - unexpected unlock
The root cause is the missing annotation at set_link_state()
Add the missing __must_hold(&dum->lock)
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Sparse reports a warning at xudc_handle_setup()
warning: context imbalance in xudc_handle_setup() - unexpected unlock
The root cause is the missing annotation at xudc_handle_setup()
Add the missing __must_hold(&udc->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
module_usb_composite_driver() makes the code simpler by
eliminating boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/omap_udc.c:2579:2-3: Unneeded semicolon
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/mv_u3d_core.c:1551:5-13: WARNING: Comparison to
bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/net2272.c:57:12-19: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool
variable
drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The variable status is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~
1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.
Commit afe956c577 ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.
Fixes: 3fc154b6b8 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to handle the case seen when the bus is
suspended by the HOST, and the device opens the port (cat /dev/ttyGS0).
Gadget controller (like DWC2) doesn't accept usb requests to be queued in
this case (when in L2 state), from the gs_open() call. Error log is printed
- configfs-gadget gadget: acm ttyGS0 can't notify serial state, -11
If the HOST resumes (opens) the bus, the port still isn't functional.
Use suspend/resume callbacks to monitor the gadget suspended state by using
'suspended' flag. In case the port gets opened (cat /dev/ttyGS0), the I/O
stream will be delayed until the bus gets resumed by the HOST.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the remote wakeup interrupt is triggered, lx_state is resumed from L2
to L0 state. But when the gadget resume is called, lx_state is still L2.
This prevents the resume callback to queue any request. Any attempt
to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN
Call the gadget resume routine after the core is in L0 state.
Fixes: f81f46e1f5 ("usb: dwc2: implement hibernation during bus suspend/resume")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch changes the function uvc_video_pump to be a separate
scheduled worker. This way the completion handler of each usb request
and every direct caller of the pump has only to schedule the worker
instead of doing the request handling by itself.
Moving the request handling to one thread solves the locking problems
between the three queueing cases in the completion handler, v4l2_qbuf
and video_enable.
Many drivers handle the completion handlers directly in their interrupt
handlers. This patch also reduces the workload on each interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/function/f_fs.c:2507:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is now a dedicated driver for these SoCs making the old compatible
obsolete.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to add support for the Amlogic GXL/GXM USB Glue, this adds
the corresponding :
- PHY names
- clock names
- USB2 PHY init and mode set
- regmap setup
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, the OTG PHY status signals are always
connected to the DWC3 controller, thus crashing the controller when
switching to OTG mode when port is not populated with a device/cable to
Host.
Amlogic added a bit to disconnect the OTG PHY status signals from the DWC3
to be used when switching the OTG PHY as Device to the DWC2 controller.
The drawback is that it makes the DWC3 port state machine stall and needs
a full reset of the DWC3 controller to get connect status to the port
connected to the OTG PHY, but not the other one.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB init code patch to handle the Amlogic GXL/GXM needing
to initialize the OTG port as Peripheral mode for the DWC2 IP to probe
correctly.
A secondary, post_init callback is added to setup the OTG PHY mode after
powering up the PHYs and before probing the DWC2 and DWC3 controllers.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following gcc warning:
drivers/usb/gadget/udc/gr_udc.c:51:19: warning: ‘driver_desc’ defined
but not used [-Wunused-const-variable=]
static const char driver_desc[] = DRIVER_DESC;
^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 48ba02b2e2 ("usb: gadget: add udc driver for max3420")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to MediaTek USB3 Dual Role controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
And delete cdsn3_hw_role_state_machine declare which doesn't
be needed.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In short, we have three kinds of role switches:
- Based on SoC: ID and VBUS
- Based on external connnctor, eg, Type-C or GPIO Connector
- Based on user choices through sysfs
Since HW handling and usb-role-switch handling are at
different places, we do not need role_override any more,
and this flag could not judge external connector case well.
With role_override deleted, We use cdns3_hw_role_switch for
the 1st use case, and usb-role-switch for the 2nd and 3rd cases.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After that, the role switch device (eg, Type-C device) could call
cdns3_role_set to finish the role switch.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If there are still pending requests because no TRB was available,
prepare more when started requests are completed.
Introduce dwc3_gadget_ep_should_continue() to check for incomplete and
pending requests to resume updating new TRBs to the controller's TRB
cache.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Register vbus_draw to gadget ops and update corresponding vbus
draw current to usb_phy.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When I switched on USB role switching for the tps6598x I completely forgot
to add the Kconfig dependency.
Ensure USB_ROLE_SWITCH is selected to prevent the typs6598x driver being
compiled in but the role-switch driver being compiled as a module, leading
to link error.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200520153617.610909-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function ehci_mxc_drv_probe() does not perform sufficient error
checking after executing platform_get_irq(), thus fix it.
Fixes: 7e8d5cd93f ("USB: Add EHCI support for MX27 and MX31 based boards")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200513132647.5456-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison of hcd->irq to less than zero for an error check will
never be true because hcd->irq is an unsigned int. Fix this by
assigning the int retval to the return of platform_get_irq and checking
this for the -ve error condition and assigning hcd->irq to retval.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: c856b4b0fd ("USB: EHCI: ehci-mv: fix error handling in mv_ehci_probe()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200515165453.104028-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When renesas module is not built, we get compiler warning on xhci driver
with W=1
CC [M] drivers/usb/host/xhci-rcar.o
drivers/usb/host/xhci-pci.h:13:5: warning: no previous prototype for ‘renesas_xhci_check_request_fw’ [-Wmissing-prototypes]
int renesas_xhci_check_request_fw(struct pci_dev *dev,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-pci.h:19:6: warning: no previous prototype for ‘renesas_xhci_pci_exit’ [-Wmissing-prototypes]
void renesas_xhci_pci_exit(struct pci_dev *dev) { };
^~~~~~~~~~~~~~~~~~~~~
We have defined these symbols when CONFIG_USB_XHCI_PCI_RENESAS is not
defined, but missed making then static.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 8bd5741e31 ("usb: renesas-xhci: Add the renesas xhci driver")
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200519093002.1152144-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_wwan_indat_callback() shouldn't resubmit rx urb if the previous urb
status is a fatal error. Or the usb controller would keep processing the
new urbs then run into interrupt storm, and has no chance to recover.
Fixes: 6c1ee66a0b ("USB-Serial: Fix error handling of usb_wwan")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The xhci-pci-renesas module exports symbols for xhci-pci to load the
RAM/ROM on renesas xhci controllers. We had dependency which works
when both the modules are builtin or modules.
But if xhci-pci is inbuilt and xhci-pci-renesas in module, we get below
linker error:
drivers/usb/host/xhci-pci.o: In function `xhci_pci_remove':
drivers/usb/host/xhci-pci.c:411: undefined reference to `renesas_xhci_pci_exit'
drivers/usb/host/xhci-pci.o: In function `xhci_pci_probe':
drivers/usb/host/xhci-pci.c:345: undefined reference to `renesas_xhci_check_request_fw'
Fix this by adding USB_XHCI_PCI having depends on USB_XHCI_PCI_RENESAS
|| !USB_XHCI_PCI_RENESAS so that both can be either inbuilt or modules.
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Fixes: a66d21d7db ("usb: xhci: Add support for Renesas controller with memory")
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20200519050622.994908-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_unaligned_le16() is defined in linux/unaligned/access_ok.h header
but it uses symbols which may not be available, leading to build
failures on ia64. Using asm/unaligned.h seem to be the right thing
and used in other drivers.
This fixes below error reported by kbuild test robot
In file included from drivers/usb/host/xhci-pci-renesas.c:9:
>> include/linux/unaligned/access_ok.h:8:28: error: redefinition of 'get_unaligned_le16'
8 | static __always_inline u16 get_unaligned_le16(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from arch/ia64/include/asm/unaligned.h:5,
from arch/ia64/include/asm/io.h:23,
from arch/ia64/include/asm/smp.h:21,
from include/linux/smp.h:67,
from include/linux/percpu.h:7,
from include/linux/arch_topology.h:9,
from include/linux/topology.h:30,
from include/linux/gfp.h:9,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/of.h:17,
from include/linux/irqdomain.h:35,
from include/linux/acpi.h:13,
from drivers/usb/host/xhci-pci-renesas.c:4:
include/linux/unaligned/le_struct.h:7:19: note: previous definition of 'get_unaligned_le16' was here
7 | static inline u16 get_unaligned_le16(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/xhci-pci-renesas.c:9:
include/linux/unaligned/access_ok.h:13:28: error: redefinition of 'get_unaligned_le32'
13 | static __always_inline u32 get_unaligned_le32(const void *p)
| ^~~~~~~~~~~~~~~~~~
In file included from arch/ia64/include/asm/unaligned.h:5,
from arch/ia64/include/asm/io.h:23,
from arch/ia64/include/asm/smp.h:21,
from include/linux/smp.h:67,
from include/linux/percpu.h:7,
from include/linux/arch_topology.h:9,
from include/linux/topology.h:30,
from include/linux/gfp.h:9,
from include/linux/xarray.h:14,
from include/linux/radix-tree.h:18,
from include/linux/idr.h:15,
from include/linux/kernfs.h:13,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/of.h:17,
from include/linux/irqdomain.h:35,
from include/linux/acpi.h:13,
from drivers/usb/host/xhci-pci-renesas.c:4:
include/linux/unaligned/le_struct.h:12:19: note: previous definition of 'get_unaligned_le32' was here
Fixes: 8bd5741e31 ("usb: renesas-xhci: Add the renesas xhci driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200516162516.385149-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uPD720201 supports ROM and allows software to program the ROM and boot
from it. Add support for detecting if ROM is present, if so load the ROM
if not programmed earlier.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-5-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some rensas controller like uPD720201 and uPD720202 need firmware to be
loaded. Add these devices in table and invoke renesas firmware loader
functions to check and load the firmware into device memory when
required.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-4-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add a new driver for renesas xhci which is basically a firmware
loader for uPD720201 and uPD720202 w/o ROM. The xhci-pci driver will
invoke this driver for loading/unloading on relevant devices.
This patch adds a firmware loader for the uPD720201K8-711-BAC-A
and uPD720202K8-711-BAA-A variant. Both of these chips are listed
in Renesas' R19UH0078EJ0500 Rev.5.00 "User's Manual: Hardware" as
devices which need the firmware loader on page 2 in order to
work as they "do not support the External ROM".
The "Firmware Download Sequence" is describe in chapter
"7.1 FW Download Interface" R19UH0078EJ0500 Rev.5.00 page 131.
The firmware "K2013080.mem" is available from a USB3.0 Host to
PCIe Adapter (PP2U-E card) "Firmware download" archive. An
alternative version can be sourced from Netgear's WNDR4700 GPL
archives.
The release notes of the PP2U-E's "Firmware Download" ver 2.0.1.3
(2012-06-15) state that the firmware is for the following devices:
- uPD720201 ES 2.0 sample whose revision ID is 2.
- uPD720201 ES 2.1 sample & CS sample & Mass product, ID is 3.
- uPD720202 ES 2.0 sample & CS sample & Mass product, ID is 2.
[vkoul: fixed comments:
used macros for timeout count and delay
removed renesas_fw_alive_check
cleaned renesas_fw_callback
removed recursion for renesas_fw_download
add register defines and field names
move to a separate file
make fw loader as sync probe so that we execute in probe and
prevent race
make xhci-pci-renesas a seprate module]
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-3-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_hcd_pci_probe expects users to call this with driver_data set as
hc_driver, that limits the possibility of using the driver_data for
driver data.
Add hc_driver as argument to usb_hcd_pci_probe and modify the callers
ehci/ohci/xhci/uhci to pass hc_driver as argument and freeup the
driver_data used
Tested xhci driver on Dragon-board RB3, compile tested ehci, ohci and
uhci.
[For all but the xHCI parts]
[For the xhci part]
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20200514122039.300417-2-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FuzzUSB (a variant of syzkaller) found an illegal array access
using an incorrect index while binding a gadget with UDC.
Reference: https://www.spinics.net/lists/linux-usb/msg194331.html
This bug occurs when a size variable used for a buffer
is misused to access its strcpy-ed buffer.
Given a buffer along with its size variable (taken from user input),
from which, a new buffer is created using kstrdup().
Due to the original buffer containing 0 value in the middle,
the size of the kstrdup-ed buffer becomes smaller than that of the original.
So accessing the kstrdup-ed buffer with the same size variable
triggers memory access violation.
The fix makes sure no zero value in the buffer,
by comparing the strlen() of the orignal buffer with the size variable,
so that the access to the kstrdup-ed buffer is safe.
BUG: KASAN: slab-out-of-bounds in gadget_dev_desc_UDC_store+0x1ba/0x200
drivers/usb/gadget/configfs.c:266
Read of size 1 at addr ffff88806a55dd7e by task syz-executor.0/17208
CPU: 2 PID: 17208 Comm: syz-executor.0 Not tainted 5.6.8 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x131/0x1b0 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:641
__asan_report_load1_noabort+0x14/0x20 mm/kasan/generic_report.c:132
gadget_dev_desc_UDC_store+0x1ba/0x200 drivers/usb/gadget/configfs.c:266
flush_write_buffer fs/configfs/file.c:251 [inline]
configfs_write_file+0x2f1/0x4c0 fs/configfs/file.c:283
__vfs_write+0x85/0x110 fs/read_write.c:494
vfs_write+0x1cd/0x510 fs/read_write.c:558
ksys_write+0x18a/0x220 fs/read_write.c:611
__do_sys_write fs/read_write.c:623 [inline]
__se_sys_write fs/read_write.c:620 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:620
do_syscall_64+0x9e/0x510 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Kyungtae Kim <kt0755@gmail.com>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200510054326.GA19198@pizza01
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main part here are the important fixes for the raw-gadget before it
becomes an ABI. We're adding support for stall/halt/wedge which is
actually pretty important in many situations. There's also a NULL
pointer deref fix.
Apart from raw-gadget, I've included some recent sparse fixes to a few
drivers.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=0P11
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.7-rc6
The main part here are the important fixes for the raw-gadget before it
becomes an ABI. We're adding support for stall/halt/wedge which is
actually pretty important in many situations. There's also a NULL
pointer deref fix.
Apart from raw-gadget, I've included some recent sparse fixes to a few
drivers.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'fixes-for-v5.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: cdns3: gadget: make a bunch of functions static
usb: mtu3: constify struct debugfs_reg32
usb: gadget: udc: atmel: Make some symbols static
usb: raw-gadget: fix null-ptr-deref when reenabling endpoints
usb: raw-gadget: documentation updates
usb: raw-gadget: support stalling/halting/wedging endpoints
usb: raw-gadget: fix gadget endpoint selection
usb: raw-gadget: improve uapi headers comments
In commit 2bef9aed6f ("usb: usbfs: correct kernel->user page attribute
mismatch") we switched from always calling remap_pfn_range() to call
dma_mmap_coherent() to handle issues with systems with non-coherent USB host
controller drivers. Unfortunatly, as syzbot quickly told us, not all the world
is host controllers with DMA support, so we need to check what host controller
we are attempting to talk to before doing this type of allocation.
Thanks to Christoph for the quick idea of how to fix this.
Fixes: 2bef9aed6f ("usb: usbfs: correct kernel->user page attribute mismatch")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Reported-by: syzbot+353be47c9ce21b68b7ed@syzkaller.appspotmail.com
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200514112711.1858252-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On platforms with IOMMU enabled, multiple SGs can be coalesced into one
by the IOMMU driver. In that case the SG list processing as part of the
completion of a urb on a bulk endpoint can result into a NULL pointer
dereference with the below stack dump.
<6> Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<6> pgd = c0004000
<6> [0000000c] *pgd=00000000
<6> Internal error: Oops: 5 [#1] PREEMPT SMP ARM
<2> PC is at xhci_queue_bulk_tx+0x454/0x80c
<2> LR is at xhci_queue_bulk_tx+0x44c/0x80c
<2> pc : [<c08907c4>] lr : [<c08907bc>] psr: 000000d3
<2> sp : ca337c80 ip : 00000000 fp : ffffffff
<2> r10: 00000000 r9 : 50037000 r8 : 00004000
<2> r7 : 00000000 r6 : 00004000 r5 : 00000000 r4 : 00000000
<2> r3 : 00000000 r2 : 00000082 r1 : c2c1a200 r0 : 00000000
<2> Flags: nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
<2> Control: 10c0383d Table: b412c06a DAC: 00000051
<6> Process usb-storage (pid: 5961, stack limit = 0xca336210)
<snip>
<2> [<c08907c4>] (xhci_queue_bulk_tx)
<2> [<c0881b3c>] (xhci_urb_enqueue)
<2> [<c0831068>] (usb_hcd_submit_urb)
<2> [<c08350b4>] (usb_sg_wait)
<2> [<c089f384>] (usb_stor_bulk_transfer_sglist)
<2> [<c089f2c0>] (usb_stor_bulk_srb)
<2> [<c089fe38>] (usb_stor_Bulk_transport)
<2> [<c089f468>] (usb_stor_invoke_transport)
<2> [<c08a11b4>] (usb_stor_control_thread)
<2> [<c014a534>] (kthread)
The above NULL pointer dereference is the result of block_len and the
sent_len set to zero after the first SG of the list when IOMMU driver
is enabled. Because of this the loop of processing the SGs has run
more than num_sgs which resulted in a sg_next on the last SG of the
list which has SG_END set.
Fix this by check for the sg before any attributes of the sg are
accessed.
[modified reason for null pointer dereference in commit message subject -Mathias]
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Cc: stable@vger.kernel.org
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200514110432.25564-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
mtu3_prb_regs is never changed and can therefore be made const.
This allows the compiler to put it in the text section instead of the
data section.
Before:
text data bss dec hex filename
19966 7120 0 27086 69ce drivers/usb/mtu3/mtu3_debugfs.o
After:
text data bss dec hex filename
20142 6992 0 27134 69fe drivers/usb/mtu3/mtu3_debugfs.o
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warnings:
drivers/usb/gadget/udc/atmel_usba_udc.c:188:30: warning: symbol 'queue_dbg_fops' was not declared.
drivers/usb/gadget/udc/atmel_usba_udc.c:196:30: warning: symbol 'regs_dbg_fops' was not declared.
queue_dbg_fops and regs_dbg_fops have only call within atmel_usba_udc.c
They should be static
Fixes: 914a3f3b37 ("USB: add atmel_usba_udc driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently we preassign gadget endpoints to raw-gadget endpoints during
initialization. Fix resetting this assignment in raw_ioctl_ep_disable(),
otherwise we will get null-ptr-derefs when an endpoint is reenabled.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Raw Gadget is currently unable to stall/halt/wedge gadget endpoints,
which is required for proper emulation of certain USB classes.
This patch adds a few more ioctls:
- USB_RAW_IOCTL_EP0_STALL allows to stall control endpoint #0 when
there's a pending setup request for it.
- USB_RAW_IOCTL_SET/CLEAR_HALT/WEDGE allow to set/clear halt/wedge status
on non-control non-isochronous endpoints.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently automatic gadget endpoint selection based on required features
doesn't work. Raw Gadget tries iterating over the list of available
endpoints and finding one that has the right direction and transfer type.
Unfortunately selecting arbitrary gadget endpoints (even if they satisfy
feature requirements) doesn't work, as (depending on the UDC driver) they
might have fixed addresses, and one also needs to provide matching
endpoint addresses in the descriptors sent to the host.
The composite framework deals with this by assigning endpoint addresses
in usb_ep_autoconfig() before enumeration starts. This approach won't work
with Raw Gadget as the endpoints are supposed to be enabled after a
set_configuration/set_interface request from the host, so it's too late to
patch the endpoint descriptors that had already been sent to the host.
For Raw Gadget we take another approach. Similarly to GadgetFS, we allow
the user to make the decision as to which gadget endpoints to use.
This patch adds another Raw Gadget ioctl USB_RAW_IOCTL_EPS_INFO that
exposes information about all non-control endpoints that a currently
connected UDC has. This information includes endpoints addresses, as well
as their capabilities and limits to allow the user to choose the most
fitting gadget endpoint.
The USB_RAW_IOCTL_EP_ENABLE ioctl is updated to use the proper endpoint
validation routine usb_gadget_ep_match_desc().
These changes affect the portability of the gadgets that use Raw Gadget
when running on different UDCs. Nevertheless, as long as the user relies
on the information provided by USB_RAW_IOCTL_EPS_INFO to dynamically
choose endpoint addresses, UDC-agnostic gadgets can still be written with
Raw Gadget.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, the PMC HPD request LVL bit field is bit 4.
Fix the definition here to match the programming guide.
Since this bit field is changing, explicitly define a field for the
HPD_HIGH mode data bit.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200511091837.102508-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the build system changes needed to get the Broadcom STB XHCI,
EHCI and OHCI functionality working. The OHCI support does not
require anything unique to Broadcom so the standard ohci-platform
driver is being used. Also update MAINTAINERS.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200512150019.25903-6-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new EHCI driver for Broadcom STB SoC's. A new EHCI driver
was created instead of adding support to the existing ehci platform
driver because of the code required to work around bugs in the EHCI
controller. The primary workaround is for a bug where the Core
violates the SOF interval between the first two SOFs transmitted after
resume. This only happens if the resume occurs near the end of a
microframe. The fix is to intercept the ehci-hcd request to complete
RESUME and align it to the start of the next microframe.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200512150019.25903-5-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Broadcom STB SoC's to the xhci platform driver
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200512150019.25903-4-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds USB role switch support to the tps6598x.
The setup to initiate or accept a data-role switch is both assumed and
currently required to be baked-into the firmware as described in TI's
document here.
Link: https://www.ti.com/lit/an/slva843a/slva843a.pdf
With this change its possible to use the USB role-switch API to detect and
notify role-switches to downstream consumers.
Tested with a ChipIdea controller on a Qualcomm MSM8939.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200511231930.2825183-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBU and HSL orientation may be fixed/static from the mux
PoW. Apparently the retimer may take care of the orientation
of these lines. Handling the static SBU (AUX) and HSL
orientation with device properties.
If the SBU orientation is static, a device property
"sbu-orintation" can be used. When the property exists, the
driver always sets the SBU orientation according to the
property value, and when it's not set, the driver uses the
cable plug orientation with SBU.
And with static HSL orientation, "hsl-orientation" device
property can be used in the same way.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200507150900.12102-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now we don't report to user-space a role switch when doing a
usb_role_switch_set_role() despite having registered the uevent callbacks.
This patch switches on the notifications allowing user-space to see
role-switch change notifications and subsequently determine the current
controller data-role.
example:
PFX=/devices/platform/soc/78d9000.usb/ci_hdrc.0
root@somebox# udevadm monitor -p
KERNEL[49.894994] change $PFX/usb_role/ci_hdrc.0-role-switch (usb_role)
ACTION=change
DEVPATH=$PFX/usb_role/ci_hdrc.0-role-switch
SUBSYSTEM=usb_role
DEVTYPE=usb_role_switch
USB_ROLE_SWITCH=ci_hdrc.0-role-switch
SEQNUM=2432
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Wen Yang <wenyang@linux.alibaba.com>
Cc: chenqiwu <chenqiwu@xiaomi.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200508162937.2566818-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 7d9e6f5aeb ("usb: host: ohci-sm501: init genalloc for local memory")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200506135625.106910-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
mv_ehci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20200508114305.15740-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Delete unused initialized value, because 'retval' will be assigined
by the function mv_ehci_enable(). And delete the extra blank lines.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200508142136.4232-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the defined variable "dev" to make the code cleaner. And
delete an extra blank line.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200508144024.7836-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scsi_get_host_dev() will create a virtual device such that either
the target id is ignored from scanning (if 'this_id' is set to
something which can be reached during scanning) or if the driver
needs a scsi device for the HBA to send commands to.
Neither is true for sierra-ms; 'this_id' remains at the default
value '-1' and the created device is never ever used within
the driver.
So kill it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200505143019.57418-1-hare@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the Raspberry Pi 4, after a PCI reset, VL805's firmware may either be
loaded directly from an EEPROM or, if not present, by the SoC's
VideoCore. Inform VideoCore that VL805 was just reset.
Also, as this creates a dependency between USB_PCI and VideoCore's
firmware interface, and since USB_PCI can't be set as a module neither
this can. Reflect that on the firmware interface Kconfg.
Link: https://lore.kernel.org/r/20200505161318.26200-5-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
They must return the number of bytes transferred during the data stage.
Fixes: 068fbff4f8 ("usb: raw-gadget: Fix copy_to/from_user() checks")
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Calling into the role switch API requires that these functions
are loaded, if they are in a loadable module and dwc3 itself
is built-in, this produces a link error:
drivers/usb/dwc3/drd.o: In function `dwc3_usb_role_switch_get':
drd.c:(.text+0x26): undefined reference to `usb_role_switch_get_drvdata'
drivers/usb/dwc3/drd.o: In function `dwc3_usb_role_switch_set':
drd.c:(.text+0x97): undefined reference to `usb_role_switch_get_drvdata'
drivers/usb/dwc3/drd.o: In function `dwc3_drd_init':
drd.c:(.text+0x1ca7): undefined reference to `usb_role_switch_register'
drivers/usb/dwc3/drd.o: In function `dwc3_drd_exit':
drd.c:(.text+0x1e92): undefined reference to `usb_role_switch_unregister'
Select the USB_ROLE_SWITCH symbol from dwc3 in that configuration.
Fixes: 0339f7fbc8 ("usb: dwc3: fix up for role switch API change")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If 'usb_otg_descriptor_alloc()' fails, we must return a
negative error code -ENOMEM, not 0.
Fixes: 1156e91dd7 ("usb: gadget: ncm: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If 'usb_otg_descriptor_alloc()' fails, we must return a
negative error code -ENOMEM, not 0.
Fixes: ab6796ae98 ("usb: gadget: cdc2: allocate and init otg descriptor by otg capabilities")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following cppcheck warnings:
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the XUDC device is idle (i.e. powergated), care must be taken not
to access any registers because that would lead to a crash.
Move the call to tegra_xudc_device_mode_off() into the same conditional
as the tegra_xudc_powergate() call to make sure we only force device
mode off if the XUDC is actually powered up.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
'dev' is allocated in 'net2272_probe_init()'. It must be freed in the error
handling path, as already done in the remove function (i.e.
'net2272_plat_remove()')
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A call to 'regulator_get()' is hidden in 'twl6030_usb_ldo_init()'. A
corresponding put must be performed in the error handling path, as
already done in the remove function.
While at it, also move a 'free_irq()' call in the error handling path in
order to be consistent.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If 'usb_otg_descriptor_alloc()' fails, we must return an error code, not 0.
Fixes: 56023ce0fd ("usb: gadget: audio: allocate and init otg descriptor by otg capabilities")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Intel Merrifield provides a DR support via PMIC which has its own
extcon driver.
Add a property string to link to that driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The check for the HWO flag in dwc3_gadget_ep_reclaim_trb_sg()
causes us to break out of the loop before we call
dwc3_gadget_ep_reclaim_completed_trb(), which is what likely
should be clearing the HWO flag.
This can cause odd behavior where we never reclaim all the trbs
in the sg list, so we never call giveback on a usb req, and that
will causes transfer stalls.
This effectively resovles the adb stalls seen on HiKey960
after userland changes started only using AIO in adbd.
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Josh Gao <jmgao@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: stable@vger.kernel.org #4.20+
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently we check to make sure there is no error state on the extcon
handle for VBUS when writing to the HS_PHY_GENCONFIG_2 register. When using
the USB role-switch API we still need to write to this register absent an
extcon handle.
This patch makes the appropriate update to ensure the write happens if
role-switching is true.
Fixes: 05559f10ed ("usb: chipidea: add role switch class support")
Cc: stable <stable@vger.kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200507004918.25975-2-peter.chen@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a fix adding a missing input sanity check and a new modem device
id.
Both have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXrLNGgAKCRALxc3C7H1l
CL9cAQDKplqMiVKST+Zmkj4tWjNT1cyCaUd0Ph5A6G5c3mp9KAD9FVmA8hs2ZJCe
5EbgjBaQaKcoRCTb+Gu2OZxX3AIt3ww=
=0Lm7
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.7-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.7-rc5
Here's a fix adding a missing input sanity check and a new modem device
id.
Both have been in linux-next with no reported issues.
* tag 'usb-serial-5.7-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: Add DW5816e support
USB: serial: garmin_gps: add sanity checking for data length
The flag provided by the USB role-switch logic allow_userspace_control
allows user-space to trigger a role-switch. Several other USB controller
drivers already enable this feature. Let's switch it on for the chipidea
core now also.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Jun Li <jun.li@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx7ulp uses different USB PHY with imx7d (MXS PHY vs PICO PHY), so the
features are supported by non-core register are a little different.
For example, autoresume feature is supported by all controllers for
imx7ulp, but for imx7d, it is only supported by non-HSIC controller.
Besides, these two platforms use different HSIC controller, imx7ulp
needs software operation, but imx7d doesn't.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The bootloader may use device mode, and keep dp up. We need dp
to be pulled down before possbile charger detection operation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx7d (and imx8mm, imx8mn) uses Samsung PHY and USB generic PHY driver.
The USB generic PHY driver is impossible to have a charger detection
for every user, so we implement USB charger detection routine at glue
layer. After the detection has finished, it will notify USB PHY
charger framework, and the uevents will be triggered.
Signed-off-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Some vendors glue layer need to handle some events for vbus, eg,
some i.mx platforms (imx7d, imx8mm, imx8mn, etc) needs vbus event
to handle charger detection, its charger detection is finished at
glue layer code, but not at USB PHY driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, when a device is transitioning to DP Alternate Mode state, if the
HPD_STATE (bit 7) field in the status update command VDO is set to
HPD_HIGH, the HPD_HIGH field in the Alternate Mode request “mode_data”
field (bit 14) should also be set. Ensure the bit is correctly handled
while issuing the Alternate Mode request.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200429054432.134178-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some architectures (e.g. arm64) requests for
IO coherent memory may use non-cachable attributes if
the relevant device isn't cache coherent. If these
pages are then remapped into userspace as cacheable,
they may not be coherent with the non-cacheable mappings.
In particular this happens with libusb, when it attempts
to create zero-copy buffers for use by rtl-sdr
(https://github.com/osmocom/rtl-sdr/). On low end arm
devices with non-coherent USB ports, the application will
be unexpectedly killed, while continuing to work fine on
arm machines with coherent USB controllers.
This bug has been discovered/reported a few times over
the last few years. In the case of rtl-sdr a compile time
option to enable/disable zero copy was implemented to
work around it.
Rather than relaying on application specific workarounds,
dma_mmap_coherent() can be used instead of remap_pfn_range().
The page cache/etc attributes will then be correctly set in
userspace to match the kernel mapping.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200504201348.1183246-1-jeremy.linton@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device property names for the port index number are
"usb2-port-number" and "usb3-port-number", not "usb2-port"
and "usb3-port".
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200430135657.45169-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer found a race between URB submission to endpoint 0
and device reset. Namely, during the reset we call usb_ep0_reinit()
because the characteristics of ep0 may have changed (if the reset
follows a firmware update, for example). While usb_ep0_reinit() is
running there is a brief period during which the pointers stored in
udev->ep_in[0] and udev->ep_out[0] are set to NULL, and if an URB is
submitted to ep0 during that period, usb_urb_ep_type_check() will
report it as a driver bug. In the absence of those pointers, the
routine thinks that the endpoint doesn't exist. The log message looks
like this:
------------[ cut here ]------------
usb 2-1: BOGUS urb xfer, pipe 2 != type 2
WARNING: CPU: 0 PID: 9241 at drivers/usb/core/urb.c:478
usb_submit_urb+0x1188/0x1460 drivers/usb/core/urb.c:478
Now, although submitting an URB while the device is being reset is a
questionable thing to do, it shouldn't count as a driver bug as severe
as submitting an URB for an endpoint that doesn't exist. Indeed,
endpoint 0 always exists, even while the device is in its unconfigured
state.
To prevent these misleading driver bug reports, this patch updates
usb_disable_endpoint() to avoid clearing the ep_in[] and ep_out[]
pointers when the endpoint being disabled is ep0. There's no danger
of leaving a stale pointer in place, because the usb_host_endpoint
structure being pointed to is stored permanently in udev->ep0; it
doesn't get deallocated until the entire usb_device structure does.
Reported-and-tested-by: syzbot+db339689b2101f6f6071@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2005011558590.903-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver issued START_TRANSFER and received a no-resource status,
then generally there are a few reasons for this:
1) The driver did not allocate resource for the endpoint during
power-on-reset initialization.
2) The transfer resource was reset. At this moment, we don't do this in
the driver, but it occurs when the driver issues START_CONFIG cmd to ep0
with resource index=2.
3) The driver issues the START_TRANSFER command to an already started
endpoint. Usually, this is because the END_TRANSFER command hasn't
completed yet.
Print out a warning to help debug this issue in the driver.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After a number of unsuccessful start isoc attempts due to bus-expiry
status, issue END_TRANSFER command and retry on the next XferNotReady
event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
As long as the START_TRANSFER command completes, it provides the
resource index of the endpoint. Use this when we need to issue
END_TRANSFER command to an isoc endpoint to retry with a new
XferNotReady event.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If dwc3 fails to issue START_TRANSFER/UPDATE_TRANSFER command, then we
should properly end an active transfer and give back all the started
requests. However if it's for an isoc endpoint, the failure maybe due to
bus-expiry status. In this case, don't give back the requests and wait
for the next retry.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, let the drd code
path decide the default dr_mode.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the driver is configured to use DRD role-switch, it's not OTG. There
won't be OTG irq to free. Check for dwc->otg_irq before freeing it.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Refactor the USB2 PHY init code patch to handle the Amlogic GXL/GXM
not having the PHY mode control registers in the Glue but in the PHY
registers.
The Amlogic GXL/GXM will call phy_set_mode() instead of programming the
PHY mode control registers, thus add two new callbacks to the SoC match
data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The dwc3_meson_g12a_usb_init function can return an error, check it.
Fixes: c99993376f ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to support the Amlogic GXL/GXM SoCs, the reset line must
be handled as shared since also used by the PHYs.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, only the USB control registers are available,
the PHY mode being handled in the PHY registers.
Thus, handle the PHY mode registers in separate regmaps and prepare
support for Amlogic GXL/GXM SoCs by moving the regmap setup in a callback
set in the SoC match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To handle the variable USB2 PHY counts on GXL and GXM SoCs, add the
possible PHY names for each SoC in the compatible match data.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hanjie Lin <hanjie.lin@amlogic.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The flow from function dwc3_gadget_ep_dequeue() is not easy to follow.
Refactor it for easier read. No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Remove 2 unnecessary checks:
1) A request in the started_list must have its trb field set. So
checking for req->trb is unnecessary.
2) An endpoint must have started (and have not ended) for the request to
still be in the started_list. There's no point to check if the endpoint
is started. We had this check because previously the driver didn't
handle the endpoint's started/ended flags for END_TRANSFER command
properly. See commit 9f45581f5e ("usb: dwc3: gadget: early giveback
if End Transfer already completed").
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a request is dequeued, the transfer is cancelled. Give back all
the started requests.
In most scenarios, the function driver dequeues all requests of a
transfer when there's a failure. If the function driver follows this,
then it's fine. If not, then we'd be skipping TRBs at different points
within the dequeue and enqueue pointers, making dequeue/enqueue pointers
useless. To enforce and make sure that we're properly skipping TRBs,
cancel all the started requests and give back all the cancelled requests
to the function drivers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC3 must not issue CLEAR_STALL command to control endpoints. The
controller automatically clears the STALL when it receives the SETUP
token. Also, when the driver receives ClearFeature(halt_ep), DWC3 must
stop any active transfer from the endpoint and give back all the
requests to the function drivers.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch moves patch-usb1-dev-desc logic from get-descriptor handler
to "ast_vhub_fixup_usb1_dev_desc" function so the code is executed only
once (at vhub initial time).
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The patch overrides idVendor, idProduct and bcdDevice fields in vhub
Device Descriptor if according device tree properties are defined.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If "vhub,string-descriptor" device tree property is defined, the driver
will load string descriptors from device tree; otherwise, the default
string descriptors will be used.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The USB LANGID validation code in "check_user_usb_string" function is
moved to "usb_validate_langid" function which can be used by other usb
gadget drivers.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch introduces a link list to store string descriptors with
different languages, and "ast_vhub_rep_string" function is also improved
to support multiple language usb strings.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch evaluates vhub ports' irq mask before going through per-port
irq handling one by one, which helps to speed up irq handling in case
there is no port interrupt.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The DRD module calls dwc3_set_mode() on role switches, i.e. when a device is
being plugged in. In order to support continuous runtime power management when
plugging in / unplugging a cable, we need to call pm_runtime_get_sync() in
this path.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mark all local functions static to fix sparse warnings.
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB2 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB3 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to USB peripheral controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add support for Dell Wireless 5816e to drivers/usb/serial/qcserial.c
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix the following coccicheck warning:
drivers/usb/chipidea/ci_hdrc_usb2.c:75:28-29: Unneeded semicolon
Fixes: c2de37b31f ("usb: chipidea: usb2: make clock optional")
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Fix the following coccicheck warning:
drivers/usb/core/hub.c:95:12-28: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200426094147.23467-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub was ucsi_register_port() when it should have been
ucsi_register_port_psy().
Cc: Abhilash K V <abhilash.k.v@intel.com>
Fixes: 992a60ed0d ("usb: typec: ucsi: register with power_supply class")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200427111246.4889-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the driver to use the new SCU IPC API. This allows us to get rid
of the duplicate PMC IPC implementation which is now covered in SCU IPC
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With this change the UCSI device will show up in
/sys/class/power_supply/. The following values are exported:
- online
- usb_type
- voltage_min
- voltage_max
- voltage_now
- current_max
- current_now
Once a PD-capable type-C power source is connected to the system, GET_PDOS
UCSI command is used to query all source capabilities. Request data object
(RDO) is used to get current values.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When connected to a PD-capable power-source, read & save all partner
power data objects (PDOs) by using GET_PDOS UCSI command.
Also, save the current power contract in request data object (RDO)
for that connector.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 0 is reserved in CCI (Command Status & Connector Change Indicator)
register. So, change bit-mask for connector number field to 7..1
instead of 7..0.
There would be no functional change since we were anyways right-shifing
by 1 bit.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EC firmware on Dell XPS & Latitude series does not set "Power Operation
Mode Change" bit in "Connector Status change" field of MESSAGE IN Data
while transitioning from type-C current to PD mode.
Instead the "Negotiated Power Level Change" bit is set when the "Power
Operation Mode" field shows the correct mode (i.e. PD).
This patch adds a check for this bit also, to trigger an update of
power operation mode in class driver, while handling GET_CONNECTOR_STATUS
command.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently UCSI framework doesn't update USB data role when partner type
is reported as power cable or power cable with ufp connected. This
results into no USB host mode functionality. This is valid usecase where
user wants to use legacy type c power cable with type a female connector
to attach different USB devices like mouse, thumb drive etc. Hence update
USB data role as host when partner type is reported as power cable or
power cable with ufp connected.
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following gcc warning:
drivers/usb/gadget/udc/gr_udc.c:51:19: warning: ‘driver_desc’ defined
but not used [-Wunused-const-variable=]
static const char driver_desc[] = DRIVER_DESC;
^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200417073137.39968-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to Physical Layer USB driver configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200419123559.GA4505@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200419125705.GA5172@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Storage driver configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200419131653.GA6611@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to USB Type-C support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200419133051.GA7154@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following coccicheck warning:
drivers/usb/host/pci-quirks.c:532:1-27: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:208:1-20: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:232:2-21: WARNING: Assignment of 0/1 to
bool variable
drivers/usb/host/pci-quirks.c:235:2-21: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200420042622.18564-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a dev_dbg() message to usb_create_sysfs_intf_files().
The message is not expected ever to appear; it's real purpose is to
satisfy the __must_check attribute on device_create_file() without
triggering a compiler warning about an empty statement.
In fact we don't really care if the sysfs attribute file doesn't get
created. The interface string descriptor is purely informational and
hardly ever present.
Suggested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221618500.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following versioncheck warning:
drivers/usb/early/xhci-dbc.c:21:1: unused including <linux/version.h>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200421033945.27703-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change a bunch of arguments of wrapper functions which pass signed
integer to an unsigned integer which might cause undefined behaviors
when sign integer overflow.
Signed-off-by: Changming Liu <liu.changm@northeastern.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/BL0PR06MB45482D71EA822D75A0E60A2EE5D50@BL0PR06MB4548.namprd06.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cyril Roelandt reports that his JMicron JMS566 USB-SATA bridge fails
to handle WRITE commands with the FUA bit set, even though it claims
to support FUA. (Oddly enough, a later version of the same bridge,
version 2.03 as opposed to 1.14, doesn't claim to support FUA. Also
oddly, the bridge _does_ support FUA when using the UAS transport
instead of the Bulk-Only transport -- but this device was blacklisted
for uas in commit bc3bdb12bb ("usb-storage: Disable UAS on JMicron
SATA enclosure") for apparently unrelated reasons.)
This patch adds a usb-storage unusual_devs entry with the BROKEN_FUA
flag. This allows the bridge to work properly with usb-storage.
Reported-and-tested-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221613110.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bd0e6c9614 ("usb: hub: try old enumeration scheme first for
high speed devices") changed the way the hub driver enumerates
high-speed devices. Instead of using the "new" enumeration scheme
first and switching to the "old" scheme if that doesn't work, we start
with the "old" scheme. In theory this is better because the "old"
scheme is slightly faster -- it involves resetting the device only
once instead of twice.
However, for a long time Windows used only the "new" scheme. Zeng Tao
said that Windows 8 and later use the "old" scheme for high-speed
devices, but apparently there are some devices that don't like it.
William Bader reports that the Ricoh webcam built into his Sony Vaio
laptop not only doesn't enumerate under the "old" scheme, it gets hung
up so badly that it won't then enumerate under the "new" scheme! Only
a cold reset will fix it.
Therefore we will revert the commit and go back to trying the "new"
scheme first for high-speed devices.
Reported-and-tested-by: William Bader <williambader@hotmail.com>
Ref: https://bugzilla.kernel.org/show_bug.cgi?id=207219
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: bd0e6c9614 ("usb: hub: try old enumeration scheme first for high speed devices")
CC: Zeng Tao <prime.zeng@hisilicon.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221611230.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8099f58f1e ("USB: hub: Don't record a connect-change event
during reset-resume") wasn't very well conceived. The problem it
tried to fix was that if a connect-change event occurred while the
system was asleep (such as a device disconnecting itself from the bus
when it is suspended and then reconnecting when it resumes)
requiring a reset-resume during the system wakeup transition, the hub
port's change_bit entry would remain set afterward. This would cause
the hub driver to believe another connect-change event had occurred
after the reset-resume, which was wrong and would lead the driver to
send unnecessary requests to the device (which could interfere with a
firmware update).
The commit tried to fix this by not setting the change_bit during the
wakeup. But this was the wrong thing to do; it means that when a
device is unplugged while the system is asleep, the hub driver doesn't
realize anything has happened: The change_bit flag which would tell it
to handle the disconnect event is clear.
The commit needs to be reverted and the problem fixed in a different
way. Fortunately an alternative solution was noted in the commit's
Changelog: We can continue to set the change_bit entry in
hub_activate() but then clear it when a reset-resume occurs. That way
the the hub driver will see the change_bit when a device is
disconnected but won't see it when the device is still present.
That's what this patch does.
Reported-and-tested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8099f58f1e ("USB: hub: Don't record a connect-change event during reset-resume")
Tested-by: Paul Zimmerman <pauldzim@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2004221602480.11262-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Serial device configuration.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
We must not process packets shorter than a packet ID
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-and-tested-by: syzbot+d29e9263e13ce0b9f4fd@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The default control endpoint ep0 can return a STALL indicating the
device does not support the control transfer requests. This is called
a protocol stall and does not halt the endpoint.
xHC behaves a bit different. Its internal endpoint state will always
be halted on any stall, even if the device side of the endpiont is not
halted. So we do need to issue the reset endpoint command to clear the
xHC host intenal endpoint halt state, but should not request the HS hub
to clear the TT buffer unless device side of endpoint is halted.
Clearing the hub TT buffer at protocol stall caused ep0 to become
unresponsive for some FS/LS devices behind HS hubs, and class drivers
failed to set the interface due to timeout:
usb 1-2.1: 1:1: usb_set_interface failed (-110)
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspending the bus and host controller while a port is in a over-current
condition may halt the host.
Also keep the roothub running if over-current is active.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DWC3 learns how to properly set maxpacket limit and got a fix for a
request completion bug. The raw gadget got a fix for
copy_to/from_user() checks. Atmel got an improvement on vbus
disconnect handling.
We're also adding support for another SoC to the Renesas DRD driver.
-----BEGIN PGP SIGNATURE-----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=lK94
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
USB: fixes for v5.7-rc2
DWC3 learns how to properly set maxpacket limit and got a fix for a
request completion bug. The raw gadget got a fix for
copy_to/from_user() checks. Atmel got an improvement on vbus
disconnect handling.
We're also adding support for another SoC to the Renesas DRD driver.
* tag 'fixes-for-v5.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
usb: raw-gadget: Fix copy_to/from_user() checks
usb: raw-gadget: fix raw_event_queue_fetch locking
usb: gadget: udc: atmel: Fix vbus disconnect handling
usb: dwc3: gadget: Fix request completion check
usb: dwc3: gadget: Do link recovery for SS and SSP
dt-bindings: usb: renesas,usb3-peri: add r8a77961 support
dt-bindings: usb: renesas,usbhs: add r8a77961 support
dt-bindings: usb: usb-xhci: add r8a77961 support
docs: dt: qcom,dwc3.txt: fix cross-reference for a converted file
usb: dwc3: gadget: Properly set maxpacket limit
usb: dwc3: Fix GTXFIFOSIZ.TXFDEP macro name
usb: gadget: udc: bdc: Remove unnecessary NULL checks in bdc_req_complete
The copy_to/from_user() functions return the number of bytes remaining
but we want to return negative error codes. I changed a couple checks
in raw_ioctl_ep_read() and raw_ioctl_ep0_read() to show that we still
we returning zero on error.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If queue->size check in raw_event_queue_fetch() fails (which normally
shouldn't happen, that check is a fail-safe), the function returns
without reenabling interrupts. This patch fixes that issue, along with
propagating the cause of failure to the function caller.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A DMA transfer can be in progress while vbus is lost due to a cable
disconnect. For endpoints that use DMA, this condition can lead to
peripheral hang. The patch ensures that endpoints are disabled before
the clocks are stopped to prevent this issue.
Fixes: a64ef71ddc ("usb: gadget: atmel_usba_udc: condition clocks to vbus state")
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
A request may not be completed because not all the TRBs are prepared for
it. This happens when we run out of available TRBs. When some TRBs are
completed, the driver needs to prepare the rest of the TRBs for the
request. The check dwc3_gadget_ep_request_completed() shouldn't be
checking the amount of data received but rather the number of pending
TRBs. Revise this request completion check.
Cc: stable@vger.kernel.org
Fixes: e0c42ce590 ("usb: dwc3: gadget: simplify IOC handling")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200402123837.5850-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts the FUSB302 driver to use GPIO descriptors.
The conversion to descriptors per se is pretty straight-forward.
In the process I discovered that:
1. The driver uses a completely undocumented device tree binding
for the interrupt GPIO line, "fcs,int_n". Ooops.
2. The undocumented binding, presumably since it has not seen
review, is just "fcs,int_n", lacking the compulsory "-gpios"
suffix and also something that is not a good name because
the "_n" implies the line is inverted which is something we
handle with flags in the device tree. Ooops.
3. Possibly the driver should not be requesting the line as a
GPIO and request the corresponding interrupt line by open
coding, the GPIO chip is very likely doubleing as an IRQ
controller and can probably provide an interrupt directly
for this line with interrupts-extended = <&gpio0 ...>;
4. Possibly the IRQ should just be tagged on the I2C client node
in the device tree like apparently ACPI does, as it overrides
this IRQ with client->irq if that exists.
But now it is too late to do much about that and as I can see
this is used like this in the Pinebook which is a shipping product
so let'a just contain the mess and move on.
The property currently appears in:
arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
Create a quirk in the GPIO OF library to allow this property
specifically to be specified without the "-gpios" suffix, we have
other such bindings already.
Cc: Tobias Schramm <t.schramm@manjaro.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Yueyao Zhu <yueyao@google.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200415192448.305257-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And delete cdsn3_hw_role_state_machine declare which doesn't
be needed.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In short, we have three kinds of role switches:
- Based on SoC: ID and VBUS
- Based on external connnctor, eg, Type-C or GPIO Connector
- Based on user choices through sysfs
Since HW handling and usb-role-switch handling are at
different places, we do not need role_override any more,
and this flag could not judge external connector case well.
With role_override deleted, We use cdns3_hw_role_switch for
the 1st use case, and usb-role-switch for the 2nd and 3rd cases.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After that, the role switch device (eg, Type-C device) could call
cdns3_role_set to finish the role switch.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-1-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Corsair K70 RGB RAPIDFIRE needs the USB_QUIRK_DELAY_INIT and
USB_QUIRK_DELAY_CTRL_MSG to function or it will randomly not
respond on boot, just like other Corsair keyboards
Signed-off-by: Jonathan Cox <jonathan@jdcox.net>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200410212427.2886-1-jonathan@jdcox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For userspace functions using OS Descriptors, if a function also supplies
Extended Property descriptors currently the counts and lengths stored in
the ms_os_descs_ext_prop_{count,name_len,data_len} variables are not
getting reset to 0 during an unbind or when the epfiles are closed. If
the same function is re-bound and the descriptors are re-written, this
results in those count/length variables to monotonically increase
causing the VLA allocation in _ffs_func_bind() to grow larger and larger
at each bind/unbind cycle and eventually fail to allocate.
Fix this by clearing the ms_os_descs_ext_prop count & lengths to 0 in
ffs_data_reset().
Fixes: f0175ab519 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Signed-off-by: Udipto Goswami <ugoswami@codeaurora.org>
Signed-off-by: Sriharsha Allenki <sallenki@codeaurora.org>
Reviewed-by: Manu Gautam <mgautam@codeaurora.org>
Link: https://lore.kernel.org/r/20200402044521.9312-1-sallenki@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Immediate submission in case of a babbling device can lead
to a busy loop. Introducing a delayed work.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suspend increments a counter, then kills the URBs,
then kills the scheduled work. The scheduled work, however,
may reschedule the URBs. Fix this by having the work
check the counter.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Jonas Karlsson <jonas.karlsson@actia.se>
Link: https://lore.kernel.org/r/20200415151358.32664-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SCSI error handler and block runtime PM must not allocate
memory with GFP_KERNEL. Furthermore they must not wait for
tasks allocating memory with GFP_KERNEL.
That means that they cannot share a workqueue with arbitrary tasks.
Fix this for UAS using a private workqueue.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: f9dc024a2d ("uas: pre_reset and suspend: Fix a few races")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200415141750.811-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once a device is gone, the internal state does not matter anymore.
There is no need to spam the logs.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 326349f824 ("uas: add dead request list")
Link: https://lore.kernel.org/r/20200415141750.811-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If queue->size check in raw_event_queue_fetch() fails (which normally
shouldn't happen, that check is a fail-safe), the function returns
without reenabling interrupts. This patch fixes that issue, along with
propagating the cause of failure to the function caller.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/9f7ce7a1472cfb9447f6c5a494186fa1f2670f6f.1586270396.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The copy_to/from_user() functions return the number of bytes remaining
but we want to return negative error codes. I changed a couple checks
in raw_ioctl_ep_read() and raw_ioctl_ep0_read() to show that we still
we returning zero on error.
Fixes: f2c2e71764 ("usb: gadget: add raw-gadget interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/20200406145119.GG68494@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ef441dd6af ("usb: typec: mux: Allow the muxes to be named")
the typec_switch_desc and typec_mux_desc structs contain a name field.
The pi3usb30532 driver allocates these structs on the stack and so far did
not explicitly zero the mem used for the structs. This causes the new name
fields to point to a random memory address, which in my test case happens
to be a valid address leading to "interesting" mux / switch names:
[root@localhost ~]# ls -l /sys/class/typec_mux/
total 0
lrwxrwxrwx. 1 root root 0 Apr 14 12:55 ''$'\r''-switch' -> ...
lrwxrwxrwx. 1 root root 0 Apr 14 12:55 ''$'\320\302\006''2'$'...
Explicitly initialize the structs to zero when declaring them on the stack
so that any unused fields get set to 0, fixing this.
Fixes: ef441dd6af ("usb: typec: mux: Allow the muxes to be named")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200414133313.131802-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a bug that causes the USB3 early console to freeze after
printing a single line on AMD machines because it can't parse the
Transfer TRB properly.
The spec at
https://www.intel.com/content/dam/www/public/us/en/documents/technical-specifications/extensible-host-controler-interface-usb-xhci.pdf
says in section "4.5.1 Device Context Index" that the Context Index,
also known as Endpoint ID according to
section "1.6 Terms and Abbreviations", is normally computed as
`DCI = (Endpoint Number * 2) + Direction`, which matches the current
definitions of XDBC_EPID_OUT and XDBC_EPID_IN.
However, the numbering in a Debug Capability Context data structure is
supposed to be different:
Section "7.6.3.2 Endpoint Contexts and Transfer Rings" explains that a
Debug Capability Context data structure has the endpoints mapped to indices
0 and 1.
Change XDBC_EPID_OUT/XDBC_EPID_IN to the spec-compliant values, add
XDBC_EPID_OUT_INTEL/XDBC_EPID_IN_INTEL with Intel's incorrect values, and
let xdbc_handle_tx_event() handle both.
I have verified that with this patch applied, the USB3 early console works
on both an Intel and an AMD machine.
Fixes: aeb9dd1de9 ("usb/early: Add driver for xhci debug capability")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20200401074619.8024-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FuzzUSB (a variant of syzkaller) found a free-while-still-in-use bug
in the USB scatter-gather library:
BUG: KASAN: use-after-free in atomic_read
include/asm-generic/atomic-instrumented.h:26 [inline]
BUG: KASAN: use-after-free in usb_hcd_unlink_urb+0x5f/0x170
drivers/usb/core/hcd.c:1607
Read of size 4 at addr ffff888065379610 by task kworker/u4:1/27
CPU: 1 PID: 27 Comm: kworker/u4:1 Not tainted 5.5.11 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.10.2-1ubuntu1 04/01/2014
Workqueue: scsi_tmf_2 scmd_eh_abort_handler
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xce/0x128 lib/dump_stack.c:118
print_address_description.constprop.4+0x21/0x3c0 mm/kasan/report.c:374
__kasan_report+0x153/0x1cb mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:639
check_memory_region_inline mm/kasan/generic.c:185 [inline]
check_memory_region+0x152/0x1b0 mm/kasan/generic.c:192
__kasan_check_read+0x11/0x20 mm/kasan/common.c:95
atomic_read include/asm-generic/atomic-instrumented.h:26 [inline]
usb_hcd_unlink_urb+0x5f/0x170 drivers/usb/core/hcd.c:1607
usb_unlink_urb+0x72/0xb0 drivers/usb/core/urb.c:657
usb_sg_cancel+0x14e/0x290 drivers/usb/core/message.c:602
usb_stor_stop_transport+0x5e/0xa0 drivers/usb/storage/transport.c:937
This bug occurs when cancellation of the S-G transfer races with
transfer completion. When that happens, usb_sg_cancel() may continue
to access the transfer's URBs after usb_sg_wait() has freed them.
The bug is caused by the fact that usb_sg_cancel() does not take any
sort of reference to the transfer, and so there is nothing to prevent
the URBs from being deallocated while the routine is trying to use
them. The fix is to take such a reference by incrementing the
transfer's io->count field while the cancellation is in progres and
decrementing it afterward. The transfer's URBs are not deallocated
until io->complete is triggered, which happens when io->count reaches
zero.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Kyungtae Kim <kt0755@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2003281615140.14837-100000@netrider.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 541368b46b ("usb: phy: Add driver for the Ingenic JZ4770 USB transceiver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200411063811.6767-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to DesignWare USB2 DRD Core Support.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20200328094828.GA5016@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to MediaTek USB3 Dual Role controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20200404103728.GA6011@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Dual Role (OTG-ready) Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404104952.GA6575@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Miscellaneous drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404094638.GA5319@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to ISP1760 USB host controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404093803.GA4983@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB host controller drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404092135.GA4522@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following cppcheck warnings:
drivers/usb/gadget/legacy/inode.c:1364:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1331:15: note: value is initialized
int value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1364:8: note: value is overwritten
value = -EOPNOTSUPP;
^
drivers/usb/gadget/legacy/inode.c:1817:8: style: Redundant initialization for 'value'. The initialized value is overwritten$
value = -EINVAL;
^
drivers/usb/gadget/legacy/inode.c:1787:18: note: value is initialized
ssize_t value = len, length = len;
^
drivers/usb/gadget/legacy/inode.c:1817:8: note: value is overwritten
value = -EINVAL;
^
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200403131652.8183-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
u132_static_list is a global list protected by u132_module_lock.
It is read in the u132_hcd_exit() function without holding the lock
thus may lead to data race.
However, it turns out that this list isn't used for anything useful
and thus it is okay to get rid of it.
Thus, remove the u132_static_list from u132-hcd module.
Also remove struct list_head u132_list from struct u132.
Found by Linux Driver Verification project (linuxtesting.org).
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com>
Link: https://lore.kernel.org/r/20200404174102.19862-1-madhuparnabhowmik10@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header file related to early USB devices.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200328104426.GA6401@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to USB Core.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200328091844.GA3648@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.
Fixes: 72246da40f ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c91 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:
For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).
For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.
Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.
Reference: Databook 3.30a section 3.2.2 and 3.2.3
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Change the macro name DWC3_GTXFIFOSIZ_TXFDEF to DWC3_GTXFIFOSIZ_TXFDEP
to match with the register name GTXFIFOSIZ.TXFDEP.
Fixes: 457e84b662 ("usb: dwc3: gadget: dynamically re-size TxFifos")
Fixes: 0cab8d26d6 ("usb: dwc3: Update DWC_usb31 GTXFIFOSIZ reg fields")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When building with Clang + -Wtautological-pointer-compare:
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:28: warning: comparison of
address of 'req->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~ ~~~~
drivers/usb/gadget/udc/bdc/bdc_ep.c:543:51: warning: comparison of
address of 'req->usb_req' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (req == NULL || &req->queue == NULL || &req->usb_req == NULL)
~~~~~^~~~~~~ ~~~~
2 warnings generated.
As it notes, these statements will always evaluate to false so remove
them.
Fixes: efed421a94 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Link: https://github.com/ClangBuiltLinux/linux/issues/749
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Allow to cut down on driver size for embedded config.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
