The hwmod code unconditionally calls _omap4_disable_module() on all
SoCs when a module doesn't enable correctly. This "worked" due to the
weak function omap4_cminst_wait_module_idle() in
arch/arm/mach-omap2/prcm.c, which was a no-op. But now those weak
functions are going away - they should not be used. So this patch
will now call the SoC-specific disable_module code, assuming it
exists.
Needs to be done before the weak function is removed, otherwise AM33xx
will crash early in boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.
This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user. mach-omap2/prcm.c will be removed
by a subsequent patch.
Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits. So we also need a fallback function for
these non-CM odd cases. Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Convert the OMAP2xxx APLL code to use omap2_cm_wait_module_ready(),
and move the low-level CM register manipulation functions to
mach-omap2/cm2xxx.c. The objectives here are to remove the dependency
on the deprecated omap2_cm_wait_idlest() function in
mach-omap2/prcm.c, so that code can be removed later; and move
low-level register accesses to the CM IP block to the CM code, which
will soon be moved into drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Modify the board files to use the SoC-specific system restart
functions. At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.
While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap_prcm_restart() from mach-omap2/prcm.c into SoC-specific
variants. These functions need to be able to save the reboot reason
into the scratchpad RAM. This implies a dependency on both the PRM
and SCM IP blocks, so they've been moved into their own file. This
will eventually call functions in the PRM and SCM drivers, once those
are created.
Vaibhav Hiremath <hvaibhav@ti.com> identified an unused prototype in
the first version of this patch - now removed. Tony Lindgren
<tony@atomide.com> noted a compile problem with some RMK Kconfigs;
resolved in this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Collect all of the virt_prcm_set-specific clocktype code into
mach-omap2/clkt2xxx_virt_prcm_set.c. Remove its dependency on the
'sclk' and 'vclk' global variables. Those variables will be removed
by subsequent patches.
This is part of the process of cleaning up the OMAP2xxx clock code
and preparing for the removal of the omap_prcm_restart() function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Remove the global 'dclk' variable, instead replacing it with a
variable local to the dpllcore clock type C file. This removes some
of the special-case code surrounding the OMAP2xxx clock init.
This patch is a prerequisite for the removal of the
omap_prcm_restart() code from arch/arm/mach-omap2/prcm.c. It also
cleans up some special-case OMAP2xxx clock code in the process.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Add SoC reset functions into the PRM code. These functions are based
on code from mach-omap2/prcm.c. They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).
Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c. (prcm.c is deprecated.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
gpmc_cs_set_timings() calculate ticks to be programmed by
rounding time in ns to next tick value. Hence remove
redundant rounding of nanosecond timing.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Setup the WIFI/BT GPIO pin muxes to enable WIFI/BT functionality.
This is needed to fix regression caused by recent versions of
u-boot that only mux essential pins.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Cc: Jonas Zetterberg <jozz@jozz.se>
Cc: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Matthias Brugger <mbrugger@iseebcn.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the non-DT omapdss setup code from board-generic if the board is
omap4-panda or omap4-sdp. This will give us working omapdss for those
boards when using DT kernel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device tree support for omapdss is still some way in the future. In an
effort to get a minimal DSS support for DT enabled kernel on selected
OMAP4 boards, we'll go for a temporary solution: We will call the same
non-DT omapdss setup code for OMAP4 SDP and Pandaboards from
board-generic.c, thus enabling DSS for those boards.
This patch moves the display setup code from board-4430sdp.c to
dss-common.c. dss-common.c will be called by the board-4430sdp.c when
running on non-DT kernel, and by board-generic.c when running on DT
enabled kernel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device tree support for omapdss is still some way in the future. In an
effort to get a minimal DSS support for DT enabled kernel on selected
OMAP4 boards, we'll go for a temporary solution: We will call the same
non-DT omapdss setup code for OMAP4 SDP and Pandaboards from
board-generic.c, thus enabling DSS for those boards.
This patch moves the display setup code from board-omap4panda.c to
dss-common.c. dss-common.c will be called by the board-omap4panda.c when
running on non-DT kernel, and by board-generic.c when running on DT
enabled kernel.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Platfrom device for ocp2scp is created using omap_device_build in
devices file. This is used for both omap4(musb) and omap5(dwc3).
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to reflect devices(usb_phy) attached to ocp2scp bus, ocp2scp
is assigned a device attribute to represent the attached devices.
This is needed to fix MUSB regression caused by commit c9e4412a
(arm: omap: phy: remove unused functions from omap-phy-internal.c)
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
[tony@atomide.com: updated comments for regression info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only thing omap_init_consistent_dma_size() does is increase the
consistent DMA size if CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE is defined.
Increasing the consistent DMA size should no longer be needed with CMA
in place.
This patch removes omap_init_consistent_dma_size() and also
arch/arm/mach-omap2/io.c:omap_common_init_early() which becomes an empty
function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated for moved dma.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the FIXME's in the suspend sequence since
we now intend to support system level RET support.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
commit 24d7b40a (ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for
MPU-SS) updated the regulator name used for the MPU regulator, but only
updated OMAP3, not OMAP4. Fix the OMAP4 name as well, otherwise CPUfreq
fails to find the MPU regulator.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add OMAP4460 OPP definitions for voltage and frequencies based on
OMAP4460 ES1.0 DM Operating Condition Addendum Version 0.1
The following exceptions are present:
* Smartreflex support is still on experimental mode: the gains and min
limits are currently pending characterization data. Currently OMAP4430 values
are used.
* Efuse offset for core OPP100-OV setting is not clear in documentation.
* IVA OPPs beyond OPP100 are disabled due to the delta between max OMAP4460
current requirements and Phoenix Max supply on VCORE2 in the default
configuration - boards which have supply which can support this should
explicitly call opp_enable and enable the same.
* MPU OPPs > OPPTURBO can easily be detected using a efuse burnt - currently
disabled pending clock changes to support DCC feature.
[nm@ti.com: cleanups and updates from Datamanual]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[t-kristo@ti.com: rebased to linux-3.6-rc5]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With the new parameters, I2C can now be put to high speed mode for
better performance.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
VC code now provides a table of pre-calculated I2C setup parameters,
which will be used based on the capacitance value calculated for the I2C
trace on the PCB. A default trace length of 6.3cm is used unless board
defines its own value during init. The parameters set will be the I2C
internal pull setup and the I2C timing parameters for high speed use
mode. Full speed mode is not supported as of now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
RACEN bit should only be set if the voltage and command register addresses
are the same.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This is no longer needed as the ramp times are calculated from
voltage deltas + slew rates.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
As vddmin / vddmax voltages for the pmic only describe the pmic
capabilities now, change the voltages to be according to spec.
TWL data manuals give following values:
TWL4030 (SWCS019L) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL5030 (SWCS030E) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL6030 (SWCS045A) : 0V ... 2100mV
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
We now use the previously defined oscillator setup / shutdown times
to calculate the register values for CLKSETUP.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now we select the vddmin and vddmax values based on both pmic and
voltage processor data, this allows usage of different power ICs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This contains startup and shutdown times for the oscillator. By default
use ULONG_MAX. Oscillator setup is used for calculating and setting up
latencies for sleep modes that disable oscillator.
Based on a patch from Nishanth Menon <nm@ti.com>.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 VC code now uses voltage deltas + slew rates for calculating
actual ramp times for voltage changes. Both retention / sleep +
off mode voltage ramp times are setup at the same time during
initialization.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP4 has two VOLTSETUP registers. One is controlling retention and
sleep voltage setup times, the other one off mode setup times. Both
of these need to be setup for stable behavior of the device.
The code setting up the new register will be added in the next
patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP3 VC code now uses voltage deltas + slew rates for calculating actual
ramp times for voltage changes. Previously a static value was used.
Two calculation methods are provided: i2c_timings and off_timings.
I2C timings are used during retention or off mode transition which
is initiated over I2C, and OFF timings are used if PMIC signal
(nsleep) is used to control all the off mode voltages at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
These new structs will hold the sleep voltage levels (omap_vc_params)
and voltage processor min / max voltages (omap_vp_params.) Previously
these were part of the PMIC struct, but they do not really belong there,
as they are OMAP chip specific, not PMIC specific parameters. voltdm
code is also changed to use the new structs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
These are now called vddmin and vddmax, as these fields will be used
globally for selecting voltage ranges for a pmic channel, and not
only for voltage processor.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Every PMIC has it's own eccentricities, For example, one of the
PMIC has MSB set to 1 for a specific function - voltage enable!
using an hardcoded value specific for TWL when copied over to
such an implementation causes the system to crash as the MSB bit
was 0 and the voltage got disabled!.
Instead we use actual values and depend on the convertion routines
to abstract out the eccentricities of each PMIC.
With this, we can now move the voltages to a common location in
voltage.h as they are no longer dependent on PMICs and expect the
PMIC's conversion routines to set a cap if the voltage is out of
reach for the PMIC.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
'Workaround for ROM bug because of CA9 r2pX gic control'
register change disables the gic distributor while the secondary
cpu is being booted. If a localtimer interrupt on the primary cpu
occurs when the distributor is turned off, the interrupt is lost,
and the localtimer never fires again.
Make the primary cpu wait for the secondary cpu to reenable the
gic distributor (with interrupts off for safety), and then
check if the pending bit is set in the localtimer but not the
gic. If so, ack it in the localtimer, and reset the timer with
the minimum timeout to trigger a new timer interrupt.
Signed-off-by: Colin Cross <ccross@android.com>
[s-jan@ti.com: adapted to k3.4 + validated functionality]
Signed-off-by: Sebastien Jan <s-jan@ti.com>
[t-kristo@ti.com: dropped generic ARM kernel exports from the code, rebased
to mainline]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP4+ devices, GIC register context is lost when MPUSS hits
the OSWR(Open Switch Retention). On the CPU wakeup path, ROM code
gets executed and one of the steps in it is to restore the
saved context of the GIC. The ROM Code GIC distributor restoration
is split in two parts: CPU specific register done by each CPU and
common register done by only one CPU.
Below is the abstract flow.
...............................................................
- MPUSS in OSWR state.
- CPU0 wakes up on the event(interrupt) and start executing ROM code.
[..]
- CPU0 executes "GIC Restoration:"
[...]
- CPU0 swicthes to non-secure mode and jumps to OS resume code.
[...]
- CPU0 is online in OS
- CPU0 enables the GIC distributor. GICD.Enable Non-secure = 1
- CPU0 wakes up CPU1 with clock-domain force wakeup method.
- CPU0 continues it's execution.
[..]
- CPU1 wakes up and start executing ROM code.
[..]
- CPU1 executes "GIC Restoration:"
[..]
- CPU1 swicthes to non-secure mode and jumps to OS resume code.
[...]
- CPU1 is online in OS and start executing.
[...] -
GIC Restoration: /* Common routine for HS and GP devices */
{
if (GICD != 1) { /* This will be true in OSWR state */
if (GIC_SAR_BACKUP_STATE == SAVED)
- CPU restores GIC distributor
else
- reconfigure GIC distributor to boot values.
GICD.Enable secure = 1
}
if (GIC_SAR_BACKUP_STATE == SAVED)
- CPU restore its GIC CPU interface registers if saved.
else
- reconfigure its GIC CPU interface registers to boot
values.
}
...............................................................
So as mentioned in the flow, GICD != 1 condition decides how
the GIC registers are handled in ROM code wakeup path from
OSWR. As evident from the flow, ROM code relies on the entire
GICD register value and not specific register bits.
The assumption was valid till CortexA9 r1pX version since there
was only one banked bit to control secure and non-secure GICD.
Secure view which ROM code sees:
bit 0 == Enable Non-secure
Non-secure view which HLOS sees:
bit 0 == Enable secure
But GICD register has changed between CortexA9 r1pX and r2pX.
On r2pX GICD register is composed of 2 bits.
Secure view which ROM code sees:
bit 1 == Enable Non-secure
bit 0 == Enable secure
Non-secure view which HLOS sees:
bit 0 == Enable Non-secure
Hence on OMAP4460(r2pX) devices, if you go through the
above flow again during CPU1 wakeup, GICD == 3 and hence
ROM code fails to understand the real wakeup power state
and reconfigures GIC distributor to boot values. This is
nasty since you loose the entire interrupt controller
context in a live system.
The ROM code fix done on next OMAP4 device (OMAP4470 - r2px) is to
check "GICD.Enable secure != 1" for GIC restoration in OSWR wakeup path.
Since ROM code can't be fixed on OMAP4460 devices, a work around
needs to be implemented. As evident from the flow, as long as
CPU1 sees GICD == 1 in it's wakeup path from OSWR, the issue
won't happen. Below is the flow with the work-around.
...............................................................
- MPUSS in OSWR state.
- CPU0 wakes up on the event(interrupt) and start executing ROM code.
[..]
- CPU0 executes "GIC Restoration:"
[..]
- CPU0 swicthes to non-secure mode and jumps to OS resume code.
[..]
- CPU0 is online in OS.
- CPU0 does GICD.Enable Non-secure = 0
- CPU0 wakes up CPU1 with clock domain force wakeup method.
- CPU0 waits for GICD.Enable Non-secure = 1
- CPU0 coninues it's execution.
[..]
- CPU1 wakes up and start executing ROM code.
[..]
- CPU1 executes "GIC Restoration:"
[..]
- CPU1 swicthes to non-secure mode and jumps to OS resume code.
[..]
- CPU1 is online in OS
- CPU1 does GICD.Enable Non-secure = 1
- CPU1 start executing
[...]
...............................................................
With this procedure, the GIC configuration done between the
CPU0 wakeup and CPU1 wakeup will not be lost but during this
short windows, the CPU0 will not receive interrupts.
The BUG is applicable to only OMAP4460(r2pX) devices.
OMAP4470 (also r2pX) is not affected by this bug because
ROM code has been fixed.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Added similar PM errata flag support as omap3 has. This should be used
in similar manner, set the flags during init time, and check the flag
values during runtime.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Omap no longer needs this option, mach/gpio.h is
empty.
Also remove mach/irqs.h from gpio-omap.h and
include it directly from the related omap1
gpio init files.
Otherwise omap2+ build fails for MULTI_PLATFORM.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: alsa-devel@alsa-project.org
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now mach/hardware.h is empty for omap2+ and can be
removed except for plat-omap/dmtimer.c for omap1.
Also the include of mach/irqs.h can now be removed
for shared plat-omap/i2c.c as it's no longer needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
For OMAP devices, the 32kHz counter is the default clock-source for the kernel.
However, this is not the only possible clock-source the kernel can use for OMAP
devices.
When booting with device-tree, if the 32kHz counter is the desired clock-source
for the kernel, then parse the device-tree blob to ensure that the counter is
present and if so map memory for the counter using the device-tree of_iomap()
function so we are no longer reliant on the OMAP HWMOD framework to do this for
us.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
In order to add device-tree support to the timer driver the following changes
were made ...
1. Allocate system timers (used for clock-events and clock-source) based upon
timer properties rather than using an hard-coded timer instance ID. To allow
this a new helper function called omap_dmtimer_find_by_property() has been
added for finding a timer with the particular properties in the device-tree
blob. Please note that this is an internal helper function for system timers
only to find a timer in the device-tree blob. This cannot be used by device
drivers, another API has been added for that (see below). Timers that are
allocated for system timers are dynamically disabled at boot time by adding
a status property with the value "disabled" to the timer's device-tree node.
Please note that when allocating system timers we now pass a timer ID and
timer property. The timer ID is only be used for allocating a timer when
booting without device-tree. Once device-tree migration is complete, all
the timer ID references will be removed.
2. System timer resources (memory and interrupts) are directly obtained from
the device-tree timer node when booting with device-tree, so that system
timers are no longer reliant upon the OMAP HWMOD framework to provide these
resources.
3. If DT blob is present, then let device-tree create the timer devices
dynamically.
4. When device-tree is present the "id" field in the platform_device structure
(pdev->id) is initialised to -1 and hence cannot be used to identify a timer
instance. Due to this the following changes were made ...
a). The API omap_dm_timer_request_specific() is not supported when using
device-tree, because it uses the device ID to request a specific timer.
This function will return an error if called when device-tree is present.
Users of this API should use omap_dm_timer_request_by_cap() instead.
b). When removing the DMTIMER driver, the timer "id" was used to identify the
timer instance. The remove function has been modified to use the device
name instead of the "id".
5. When device-tree is present the platform_data structure will be NULL and so
check for this.
6. The OMAP timer device tree binding has the following optional parameters ...
a). ti,timer-alwon --> Timer is in an always-on power domain
b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP
c). ti,timer-pwm --> Timer can generate a PWM output
d). ti,timer-secure --> Timer is reserved on a secure OMAP device
Search for the above parameters and set the appropriate timer attribute
flags.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
OMAP3 devices may or may not have security features enabled. Security enabled
devices are known as high-secure (HS) and devices without security are known as
general purpose (GP).
Some OMAP3 boards, such as the OMAP3 beagle board, only use GP devices and for
GP devices there is a 12th timer available on-chip that can operate at 32kHz.
The clock for 12th timer is generated by an internal oscillator and is unique
this timer. Boards such as the beagle board use this timer as a 32kHz based
clock-events timer because early versions of the board had a hardware problem
preventing them from using other on-chip timers clocked by a external 32kHz
clock.
When booting with device-tree all OMAP3 devices use timer 1 by default for
the clock-events timer. Therefore, add a generic machine descriptor for boards
with OMAP3 GP devices so that they can use the 12th timer as the clock-events
timer instead of the default.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
OMAP3 devices may or may not have security features enabled. Security enabled
devices are known as high-secure (HS) and devices without security are known as
general purpose (GP).
For OMAP3 devices there are 12 general purpose timers available. On secure
devices the 12th timer is reserved for secure usage and so cannot be used by
the kernel, where as for a GP device it is available. We can detect the OMAP
device type, secure or GP, at runtime via an on-chip register. Today, when not
using DT, we do not register the 12th timer as a linux device if the device is
secure.
When using device tree, device tree is going to register all the timer devices
it finds in the device tree blob. To prevent device tree from registering 12th
timer on a secure OMAP3 device we can add a status property to the timer
binding with the value "disabled" at boot time. Note that timer 12 on a OMAP3
device has a property "ti,timer-secure" to indicate that it will not be
available on a secure device and so for secure OMAP3 devices, we search for
timers with this property and then disable them. Using the prom_add_property()
function to dynamically add a property was a recommended approach suggested by
Rob Herring [1].
I have tested this on an OMAP3 GP device and faking it to pretend to be a
secure device to ensure that any timers marked with "ti,timer-secure" are not
registered on boot. I have also made sure that all timers are registered as
expected on a GP device by default.
[1] http://comments.gmane.org/gmane.linux.ports.arm.omap/79203
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Fix serial.h by moving it to mach/serial.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code will be eventually in drivers, and for the
code in the drivers we don't want to have any cpu_is_omap
usage. Those macros should be private to arch/arm/mach-omap1
and arch/arm/mach-omap2.
To fix this, let's move the define for dma_omap2plus()
to dma-omap.h, and use the existing dma_attr passed in
the platform_data as the revision registers are what they
are.
Note that we can now also remove the relative includes
introduced by the recent clean-up patches.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Let's add plat/debug-devices.h for debug_card_init()
to fix the relative includes.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the prototypes in plat-omap/common.h are not
common to omap1 and omap2+, they are local to omap2+
and should not be in plat-omap/common.h.
The only shared function prototype in this file is
omap_init_clocksource_32k(), let's put that into
counter-32k.h.
Note that the new plat/counter-32k.h must not be
included from drivers, that will break omap2+ build
for CONFIG_MULTIPLATFORM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code should be private to mach-omap2.
The only use for it in for omap1 has been in dmtimer.c
to check for context loss. However, omap1 does not
lose context during idle, so the code is not needed.
Further, omap1 timer has OMAP_TIMER_ALWON set, so omap1
was not hitting omap_pm_get_dev_context_loss_count()
test.
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
To fix this for the shared i2c.h, let's re-introduce
a minimal plat/i2c.h.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The common code should not have any omap1 or omap2+
specific code, and should not need to call the cpu_is_omap
macros.
The only remaining user for cpu_is_omap macros is
omap_i2c_nr_ports(). Let's make those checks in
the omap specific implementation of omap_i2c_add_bus()
instead in order to remove cpu_is_omap usage from
the common code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's make the omap2+ specific parts private to mach-omap2.
This leaves just a minimal shared code into plat-omap like
it should be.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
So this patch re-adds a minimal plat/sram.h.
The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.
Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resolve this kernel boot message:
omap_hwmod: mcpdm: cannot be enabled for reset (3)
The McPDM on OMAP4 can only receive its functional clock from an
off-chip source. This source is not guaranteed to be present on the
board, and when present, it is controlled by I2C. This would
introduce a board dependency to the early hwmod code which it was not
designed to handle. Also, neither the driver for this off-chip clock
provider nor the I2C code is available early in boot when the hwmod
code is attempting to enable and reset IP blocks. This effectively
makes it impossible to enable and reset this device during hwmod init.
At its core, this patch is a workaround for an OMAP hardware problem.
It should be possible to configure the OMAP to provide any IP block's
functional clock from an on-chip source. (This is true for almost
every IP block on the chip. As far as I know, McPDM is the only
exception.) If the kernel cannot reset and configure IP blocks, it
cannot guarantee a sane SoC state. Relying on an optional off-chip
clock also creates a board dependency which is beyond the scope of the
early hwmod code.
This patch works around the issue by marking the McPDM hwmod record
with the HWMOD_EXT_OPT_MAIN_CLK flag. This prevents the hwmod
code from touching the device early during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Péter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Add HWMOD_EXT_OPT_MAIN_CLK flag to indicate that this IP block is
dependent on an off-chip functional clock that is not guaranteed to be
present during initialization. IP blocks marked with this flag are
left in the INITIALIZED state during kernel init.
This is a workaround for a hardware problem. It should be possible to
guarantee that at least one clock source will be present and active
for any IP block's main functional clock. This ensures that the hwmod
code can enable and reset the IP block. Resetting the IP block during
kernel init prevents any bogus bootloader, ROM code, or previous OS
configuration from affecting the kernel. Hopefully a clock
multiplexer can be added on future SoCs.
N.B., at some point in the future, it should be possible to query the
clock framework for this type of information. Then this flag should
no longer be needed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Remove usage of plat/cpu.h and get information from platform data
instead. This enables omapdrm to be built with ARCH_MULTIPLATFORM.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When waking up from off-mode, some IP blocks are reset automatically by
hardware. For this reason, software must wait until the reset has
completed before attempting to access the IP block.
This patch fixes for example the bug introduced by commit
6c31b2150f ("mmc: omap_hsmmc: remove access
to SYSCONFIG register"), in which the MMC IP block is reset during
off-mode entry, but the code expects the module to be already available
during the execution of context restore.
This version includes a fix from Kevin Hilman <khilman@ti.com> for
GPIO problems on the 37xx EVM - thanks Kevin.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved softreset wait code into separate function; call
from top of _enable_sysc() rather than the bottom; include fix from Kevin
Hilman for GPIO sluggishness]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since CAM domain (ISS) has no module wake-up dependency
with any other clock domain of the device and the dynamic
dependency from L3_main_2 is always disabled, the domain
needs to be in force wakeup in order to be able to access
it for configure (sysconfig) it or use it.
Also since there is no clock in the domain managed automatically
by the hardware, there is no use to configure automatic
clock domain transition. SW should keep the SW_WKUP domain
transition as long as a module in the domain is required to
be functional.
Signed-off-by: Miguel Vadillo <vadillo@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
The OMAP watchdog timer driver directly calls a function exported by
code in arch/arm/mach-omap2. This is not good; it tightly couples
this driver to the mach-omap2 integration code. Instead, add a
temporary platform_data function pointer to abstract this function
call. A subsequent patch will convert the watchdog driver to use this
function pointer.
This patch also moves the device creation code out of
arch/arm/mach-omap2/devices.c and into arch/arm/mach-omap2/wd_timer.c.
This is another step towards the removal of
arch/arm/mach-omap2/devices.c.
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: skip wd_timer device creation when DT blob is present]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Split the omap4_hdmi_mux_pads() function into two parts, one handles the
tpd12s015 gpio muxing, the other handles the hdmi pins.
This is clearer, as hdmi and tpd12s015 are separate devices, and it also
allows us to mux those separately with DT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add missing newline to warning message to avoid annoying
wrapping problems during kernel boot like this one:
omap_vc_i2c_init: I2C config for vdd_iva does not match other channels (0).
omap_vc_i2c_init: I2C config for vdd_mpu does not match other channels (0).Power Management for TI OMAP4.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=asxx
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-a-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm
The first set of OMAP PRM/CM-related cleanup patches for 3.8.
Prepares for the future move of the PRM/CM code to drivers/. Also
includes some prcm.[ch] cleanup patches from the WDTIMER cleanup
series that don't need external acks.
Basic test logs for this branch on top of v3.7-rc2 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121021123719/
But due to the number of unrelated regressions present in v3.7-rc[12],
it's not particularly usable as a testing base. With reverts, fixes,
and workarounds applied as documented in:
http://www.pwsan.com/omap/testlogs/test_v3.7-rc2/20121020134755/README.txt
the following test logs were obtained:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_a_3.8/20121020231757/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/Makefile
arch/arm/mach-omap2/clockdomain2xxx_3xxx.c
arch/arm/mach-omap2/pm24xx.c
In order to make single zImage work for ARM architecture,
we need to make sure we don't depend on private headers.
Move USB platform_data to <linux/platform_data/omap-usb.h>
and add a minimal drivers/mfd/usb-omap.h.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated for local mfd/usb-omap.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's move what we can from plat/usb.h to the local usb.h
for ARM common zImage support.
This is needed so we can remove plat/usb.h for ARM common
zImage support.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Partha Basak <parthab@india.ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap1, we'll keep mach/serial.h around for 8250.c hardware
workarounds. For omap2+, we no longer need mach/serial.h and
can make it local to mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to eventually move omap2+ to generic
debug code that's configured in Kconfig for the port.
Signed-off-by: Tony Lindgren <tony@atomide.com>
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HUTj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
Add dmtimer clock aliases for AM33XX devices so that the parent clock for
the dmtimer can be set correctly by the dmtimer driver. Without these clock
aliases the dmtimer driver will fail to find the parent clocks for the dmtimer.
Verified that DMTIMERs can be successfully requested on AM335x beagle bone.
Original patch was provided by Vaibhav Hiremath [1]. Changelog and
additional verification performed by Jon Hunter.
[1] http://marc.info/?l=linux-omap&m=134693631608018&w=2
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit 24d7b40a60 (ARM: OMAP2+:
PM: MPU DVFS: use generic CPU device for MPU-SS), OPPs are registered
using an existing CPU device, not the omap_device for MPU-SS.
First, fix the board file to use get_cpu_device() as required by the
above commit, otherwise custom OPPs will be added to the wrong device.
Second, the board files OPP init is called from the its init_machine
method, and the generic CPU devices are not yet created when
init_machine is run. Therefore OPP initialization will fail. To fix,
use a device_initcall() for the board file's OPP customization, and
make the device_initcall board-specific by using a machine_is check.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On n900 uart1 pins are not not used for uart, instead they are
used to connect to a cell modem over ssi. Looks like we're
currently missing these signal names for 3430 for some reason,
and only have some of them listed for 3630. Obviously the signals
are there for 3430 if n900 is using them and they are documented
in some TRMs.
Note that these will eventually be replaced by device tree
based pinctrl-single.c driver. But for now these are needed
to verify the SSI pins for devices like Nokia N900.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 8f31cefe (ARM: OMAP2+: select PINCTRL in Kconfig)
added select PINCTRL, but accdentally added it to a wrong
location.
We want to select if for ARCH_OMAP2PLUS, not for
ARCH_OMAP2PLUS_TYPICAL.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The runtime PM framework assumes that the hardware state of devices
when initialized is disabled. For all omap_devices, we idle/disable
device by default. However, the console uart uses a "no idle" option
during omap_device init in order to allow earlyprintk usage to work
seamlessly during boot.
Because the hardware is left partially enabled after init (whatever
the bootloader settings were), the omap_device should later be fully
initialized (including mux) and the runtime PM framework should be
told that the device is active, and not disabled so that the hardware
state is in sync with runtime PM state.
To fix, after the device has been created/registered, call
omap_device_enable() to finialize init and use pm_runtime_set_active()
to tell the runtime PM core the device is enabled.
Tested on 2420/n810, 3530/Overo, 3530/Beagle, 3730/OveroSTORM,
3730/Beagle-xM, 4460/PandaES.
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
On OMAP34xx/35xx, and OMAP36xx chips with ES < 1.2, if the PER
powerdomain goes to OSWR or OFF while CORE stays at CSWR or ON, or if,
upon chip wakeup from OSWR or OFF, the CORE powerdomain goes ON before
PER, the UART3/4 FIFOs and McBSP2/3 SIDETONE memories will be
unusable. This is erratum i582 in the OMAP36xx Silicon Errata
document.
This patch implements one of several parts of the workaround: the
addition of the wakeup dependency between the PER and WKUP
clockdomains, such that PER will wake up at the same time CORE_L3
does.
This is not a complete workaround. For it to be complete:
1. the PER powerdomain's next power state must not be set to OSWR or
OFF if the CORE powerdomain's next power state is set to CSWR or
ON;
2. the UART3/4 FIFO and McBSP2/3 SIDETONE loopback tests should be run
if the LASTPOWERSTATEENTERED bits for PER and CORE indicate that
PER went OFF while CORE stayed on. If loopback tests fail, then
those devices will be unusable until PER and CORE can undergo a
transition from ON to OSWR/OFF and back ON.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP watchdog timer driver needs to determine what caused the SoC
to reset for its GETBOOTSTATUS ioctl. So, define a set of standard
reset sources across OMAP SoCs. For OMAP2xxx, 3xxx, and 4xxx SoCs,
define mappings from the SoC-specific reset source register bits to
the standardized reset source IDs. Create SoC-specific PRM functions
that read the appropriate per-SoC register and use the mapping to
return the standardized reset bits. Register the SoC-specific PRM
functions with the common PRM code via prm_register(). Create a
function in the common PRM code, prm_read_reset_sources(), that
calls the SoC-specific function, registered during boot.
This patch does not yet handle some SoCs, such as AM33xx. Those SoCs
were not handled by the code this will replace.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are several CM operations which behave similarly across OMAP2+
SoCs, but which have slight differences in their underlying
implementations.
This patch creates the support code for this function pointer
registration process. No function pointers are included yet, but a
subsequent patch will create these for the module IDLEST registers.
This patch allows other code to use CM-provided data and operations
without needing to know which SoC is currently in use. A further
description of the concept is provided in the patch entitled
"ARM: OMAP2+: PRM: prepare for use of prm_ll_data function pointers".
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are several PRM operations which behave similarly across OMAP2+
SoCs, but which have slight differences in their underlying
implementations. For example, to fetch the SoC's last reset sources,
different registers are read across OMAP2xxx, 3xxx, and 44xx, and
different bits are used on each SoC. But the information returned is
so similar that a single, common interface for drivers is useful.
This patch creates the support code for this function pointer
registration process. No function pointers are included yet, but a
subsequent patch will create one for the reset source API.
To illustrate the end goal with the above reset source example, each
per-SoC driver will use its own low-level implementation function --
e.g., prm2xxx.c would contain omap2xxx_prm_read_reset_sources(). This
function would read the appropriate register and remap the register
bits to a standard set of reset source bits. When the prm2xxx.c
driver is loaded, it would register this function with the common PRM
driver, prm.c. prm.c would then export a common function,
omap_prm_read_reset_sources(). Calling it would call through to the
function pointer for the currently-registered SoC PRM driver. This
will allow other drivers to use PRM-provided data and operations
without needing to know which SoC is currently in use.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the low-level SoC-specific clockdomain control functions into
cm*.c and prm*.c. For example, OMAP2xxx low-level clockdomain
functions go into cm2xxx.c. Then remove the unnecessary
clockdomain*xxx*.c files.
The objective is to centralize low-level CM and PRM register accesses
into the cm*.[ch] and prm*.[ch] files, and then to export an OMAP
SoC-independent API to higher-level OMAP power management code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move OMAP3xxx-specific CM functions & macros into cm3xxx.[ch] and
OMAP2xxx-specific macros into cm2xxx.[ch]. Move basic CM register
access functions into static inline functions in cm2xxx_3xxx.h,
leaving only OMAP2/3 hardreset functions in cm2xxx_3xxx.c.
As part of this, split the CM and hwmod code that waits for devices to
become ready into SoC-specific functions.
This is in preparation for the upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move the low-level SoC-specific powerdomain control functions into
prm*.c. For example, OMAP2xxx low-level powerdomain functions go into
prm2xxx.c. Then remove the unnecessary powerdomain*xxx*.c files.
The objective is to centralize low-level PRM register accesses into
the prm*.[ch] files, and then to export an OMAP SoC-independent API to
higher-level OMAP power management code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Remove the now-unused PRM weak functions from prm_common.c. These
were formerly used to ensure that some OMAP2/3 PRM code would build on
OMAP4, but none of those functions ever would have worked on OMAP4 due
to an incompatible PRM register layout. Now all that has been cleaned
up and these can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This adds product names (that most users know) to Kconfig and board
comments.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to remove plat/cpu.h. To do this, let's first split
it to private soc.h to mach-omap1 and mach-omap2. We have to
keep plat/cpu.h around until the remaining drivers are fixed,
so let's include the local soc.h in plat/cpu.h and for drivers
still including plat/cpu.h.
Once the drivers are fixed not to include plat/cpu.h, we
can remove the file.
This is needed for the ARM common zImage support.
[tony@atomide.com: updated to not print a warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
To facilitate the ARM single image work, split
arch/arm/plat-omap/include/plat/clkdev_omap.h into the
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h files.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove arch/arm/plat-omap/include/plat/clock.h by merging it into
arch/arm/mach-omap1/clock.h and arch/arm/mach-omap2/clock.h.
The goal here is to facilitate ARM single image kernels by removing
includes via the "plat/" symlink.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: fixed to remove duplicate clock.h includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Duplicate arch/arm/plat-omap/clock.c into arch/arm/mach-omap1/clock.c
and arch/arm/mach-omap2/clock.c. This is to support people who are working
on the ARM single image kernel and the OMAP common clock framework
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moving plat/omap-secure.h locally to mach-omap2/
as part of single zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_reserve() callback is defned only for mach-omap2.
So, moving definition of omap_reserve() to mach-omap2.
This helps is moving plat/omap_secure.h local to
mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is private to cpu.h and no other places should
need to include it and we can drop the include
in mach-omap2/io.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep the device related things in the
common i2c.c as omap2+ is using hwmod. Split the code to
mach-omap1 and mach-omap2 parts and only leave common
code to plat-omap/i2c.c.
Note that as omap1 only has one i2c controller, we can
now remove the old device related macros.
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot keep this in plat as it causes problems
with the ARM single zImage support.
Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-pcmcia@lists.infradead.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove arch/arm/plat-omap/include/plat/sdrc.h by folding its contents
into arch/arm/mach-omap2/sdrc.h. The objective is to assist Tony in
cleaning out arch/arm/plat-omap/, as his upstreams request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
[tony@atomide.com: updated to remove rotate macros]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, if the GPMC driver fails to reserve memory when probed we will
call BUG() and the kernel will not boot. Instead of calling BUG(), return
an error from probe and allow kernel to boot.
Boot tested on AM335x beagle bone board and OMAP4430 Panda board.
V2 changes:
- Ensure that clock and memory resources are released on error.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Previously the code only acquired spinlock after increasing / decreasing
the usecount value, which is wrong. This leaves a small window where
a task switch may occur between the check of the usecount and the actual
wakeup / sleep of the domain. Fixed by moving the spinlock locking before
the usecount access. Left the usecount as atomic_t if someone wants an
easy access to the parameter through atomic_read.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that VRFB driver handles its registers independently, we can remove
the VRFB related code from OMAP's sdrc.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The GPMC code has been converted to a driver by the following commit:
commit da49687397
Author: Afzal Mohammed <afzal@ti.com>
Date: Sun Sep 23 17:28:25 2012 -0600
ARM: OMAP2+: gpmc: minimal driver support
It now requests a clock with con-id "fck" otherwise the probe will fails.
[ 0.342010] omap-gpmc omap-gpmc: error: clk_get
[ 0.346771] omap-gpmc: probe of omap-gpmc failed with error -2
Add the "omap-gmpc" dev-id and fck con-id to the already existing
gmpc-fck dummy clock.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal)
changed the interrupts to allow enabling sparse IRQ, but
accidentally added the omap3 INTC base to the local IRQ.
This causes the following:
twd: can't register interrupt 45 (-22)
twd_local_timer_register failed -22
The right fix is to not add any base, as it is a local
timer. For the OMAP44XX_IRQ_LOCALWDT we had defined earlier
there are no users, so no need to fix that.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add new enum, omapdss_version, that is used to tell which DSS hardware
version the SoC has. This enum is initialized during platform init, and
passed in the platform data to omapdss driver.
Note that the versions are not "continuous", that is, you cannot check
if the version is less or greater than something, but you need to check
for exact version match. In other words, this is invalid:
/* test if DSS is 3630 or earlier */
if (ver <= OMAPDSS_VER_OMAP3630)
...
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove the device dependent code (ex. cpu_is_xxx()) and settings
from the driver code and instead pass them via the platform
data. This allows a clean separation of the driver code and the platform
code, as required by the move of the platform header files to
include/linux/platform_data.
Note about the smartreflex functional clocks: the smartreflex fclks
are derived from sys_clk and have the same name as the main_clk from
the hwmod entry, in order for the SmartReflex driver to request the
fclk (using clk_get(dev, "fck")).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rename the smartreflex fck names for consistency and better readability;
rename the clock aliases so that they match the hwmod main_clk names.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to omap1, some of the omap2+ dma channel definitions are
used by some drivers. For moving omap2+ dma channel definitions
to mach-omap2/, the used ones should be defined locally to driver.
Drivers can eliminate it using DT, platform data, or IORESOURCE_DMA
And moving omap2+ DMA channel definitions to mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can move menelaus.h to live with other mfd headers to
get it out of plat for ARM common zImage support.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to remove this from plat for ARM common zImage
support.
Also remove includes not needed by the omap_hsmmc.c driver.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Acked-by: Venkatraman S <svenkatr@ti.com>
[tony@atomide.com: fold in removal of unused driver includes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Requirement of gpmc header outside of mach-omap2 has been
cutoff, move gpmc header file in plat-omap folder to local
mach-omap2 folder
Objective - common zImage participation of omap
Signed-off-by: Afzal Mohammed <afzal@ti.com>
nand driver handles gpmc-nand block fully, hence no more
users for these exported nand functions, remove it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Update helper function that provides gpmc-nand register
details for nand driver with bch register information.
Using this nand driver can be made self sufficient to
handle remaining gpmc-nand operations by itself instead
of relying on gpmc exported nand functions.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Capability of bch schemes could be discovered using soc
revision checks. If soc revision indicates that selected
ecc scheme is not supported bail out.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
For common arm zImage existing nand header file
in platform specific location was moved to generic
platform data location, but it contained more than
platform data, remove it. New local header has been
created for exposing functions.
Also move gpmc-nand platform data to platform header
meant for nand from gpmc header file
Signed-off-by: Afzal Mohammed <afzal@ti.com>
For common arm zImage existing onenand header file
in platform specific location was moved to generic
platform data location, but it contained more than
platform data, remove it. New local header has been
created for exposing functions.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
onenand driver needs to know whether soc is falling under
34xx family to properly handle onenand. But driver is not
supposed to do cpu_is_* check, hence educate platform data
with this information. Driver can make use of it to avoid
cpu_is_* check.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Divider value for a certain sync clk is determined solely
based on gpmc fclk. CS# does not have any role here, thus
remove presence of CS# in clock divider calculation API.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
A platform function pointer for getting the frequency of a OneNAND device
was added so that a platform could specify a custom function for returning
the frequency and not just rely on the OneNAND version to determine the
frequency. However, this platform function pointer is not currently being
used and I am not sure if it ever has.
OneNAND devices are not so common these days and as far as I know not being
used with new devices. Therefore, it is most likely that this get_freq()
function pointer will not be used and so remove it.
Given that the get_freq() function pointer is not used, neither is the
clk_dep variable and so all references to it can also be removed.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Refactor set_async_mode & set_sync_mode functions to
separate out timing calculation & actual configuration
(GPMC & OneNAND side).
Thanks to Jon for his suggestions.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Helper function for updating nand platform data has been
added the capability to take timing structure arguement.
Usage of omap_nand_flash_init() has been replaced by modifed
one, omap_nand_flash_init was doing things similar to
board_nand_init except that NAND CS# were being acquired
based on bootloader setting. As CS# is hardwired for a given
board, acquiring gpmc CS# has been removed, and updated with
the value on board.
NAND CS# used in beagle board & omap3evm was found to be CS0.
Thomas Weber <thomas.weber.linux@googlemail.com> reported
that value of devkit8000 to be CS0. Overo board was found
to be using CS0 based on u-boot, while google grep says
omap3touchbook too has CS0.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because firmware
no longer sets up all pin states before starting the kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was pre-agreed).
- A longer series of misc regression fixes and cleanups, warning removals,
etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vAh+
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A series of fixes (and in some cases, some cleanups):
Via Tony Lindgren:
- A collection of OMAP regression fixes, in particular because
firmware no longer sets up all pin states before starting the
kernel.
- cpufreq fixes for OMAP (Rafael is on vacation and this was
pre-agreed).
- A longer series of misc regression fixes and cleanups, warning
removals, etc for OMAP
From Arnd Bergmann:
- A series of warning fixes for various platforms (defconfig builds)
Misc:
- A couple of tegra fixes, one for i.MX, some vt8500 fixes, etc."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: pxa: armcore: fix PCI PIO warnings
ARM: integrator: use __iomem pointers for MMIO, part 2
ARM: assabet: fix bogus warning in get_assabet_scr (again)
ARM: shmobile: mark shmobile_init_late as __init
ARM: integrator_cp: fix build failure
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
arm/omap: Replace board_ref_clock with enum values
ARM: OMAP2+: remove duplicated include from board-omap3stalker.c
arch/arm/plat-omap/omap-pm-noop.c: Remove unecessary semicolon
arch/arm/mach-omap2: Remove unecessary semicolon
arch/arm/mach-omap1/devices.c: Remove unecessary semicolon
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
...
From Tony Lindgren:
This branch contains regression fixes for omap4/5 ASoC
audio that were caused by the fact that u-boot stopped
muxing non essential pins.
As omap audio and dmaengine development happens on
these platforms, let's make sure they are usable.
Of course this should have been fixed earlier and
not during the -rc cycle.
* tag 'omap-for-v3.7-rc1/fixes-asoc-regression-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM/dts: omap5-evm: pinmux configuration for audio
ARM/dts: Add pinctrl driver entries for omap5
ARM/dts: omap4-panda: pinmux configuration for audio
ARM/dts: omap4-sdp: pinmux configuration for audio
ARM/dts: omap5-evm: Disable unused McBSP3
ARM/dts: omap4-sdp: Disable unused McBSP3
ARM/dts: omap4-panda: Disable unused audio IPs
ARM: OMAP: board-omap4panda: Pin mux configuration for audio needs
ARM: OMAP: board-4430-sdp: Pin mux configuration for audio needs
From Tony Lindgren:
These were agreed to be merged via arm soc tree as Rafael
is on vacation.
From Kevin Hilman <khilman@deeprootsystems.com>:
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
* tag 'omap-for-v3.7-rc1/fixes-cpufreq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: MPU DVFS: use generic CPU device for MPU-SS
cpufreq: OMAP: use get_cpu_device() instead of omap_device API
cpufreq: OMAP: fix clock usage to be SoC independent, remove plat/ includes
cpufreq: OMAP: remove unused <plat/omap-pm.h>
cpufreq: OMAP: ensure valid clock rate before scaling
From Kevin Hilman <khilman@deeprootsystems.com> via Tony Lindgren:
OMAP PM related fixes for v3.7-rc
* tag 'omap-for-v3.7-rc1/fixes-pm-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: SmartReflex: fix error path in init function
ARM: OMAP: SmartReflex: select CONFIG_POWER_SUPPLY in Kconfig
ARM: OMAP2+: PM: fix return value check in omap2_set_init_voltage()
ARM: OMAP2+: SmartReflex: fix return value check in sr_dev_init()
ARM: OMAP: omap_device: fix return value check in omap_device_build_ss()
ARM: OMAP: fix return value check in beagle_opp_init()
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Some OMAP fixes for the 3.7 merge window, fixing mismerges, branch
integration issues, and bugs after the arm-soc merges.
* tag 'omap-for-v3.7-rc1/fixes-hwmod-clock-signed-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4/AM335x: hwmod: fix disable_module regression in hardreset handling
ARM: OMAP3: fix workaround for EMU clockdomain
ARM: OMAP: omap3evm: fix new sparse warning
ARM: OMAP2+: hwmod data: Fix PMU interrupt definitions
ARM: am33xx: clk: Update clkdev table to add mcasp alias
Commit eb05f69129 ("ARM: OMAP: hwmod:
partially un-reset hwmods might not be properly enabled") added code
to skip the IP block disable sequence if all of the block's hardreset
lines weren't asserted. But this did not handle the case when no
hardreset lines were associated with a module, which is the general
case. In that situation, the IP block disable would be skipped. This
is likely to cause PM regressions.
So, modify _omap4_disable_module() and _am33xx_disable_module() to
only bail out early if there are any hardreset lines asserted. And
move the AM33xx test above the actual module disable code to ensure
that the behavior is consistent.
Reported-by: Archit Taneja <a0393947@ti.com>
Tested-by: Archit Taneja <a0393947@ti.com> # DSS
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com> # AM335x
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit b71c721 (ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU
clockdomain idle problems) added a workaround for the EMU clock domain on
OMAP3/4 devices to prevent the clock domain for transitioning while it is
in use.
In the proposed patch [1] code was added to the omap3xxx_clkdm_clk_enable()
and omap3xxx_clkdm_clk_disable() functions to check for the flag
CLKDM_MISSING_IDLE_REPORTING and perform the appropriate action. However, in the
merged patch it appears that this code was added to the omap2_clkdm_clk_enable()
and omap2_clkdm_clk_disable() functions by mistake.
[1] http://marc.info/?l=linux-arm-kernel&m=134383567112518&w=2
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Use the enum for board_ref_clock from linux/wl12xx.h
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Cc: linux-omap@vger.kernel.org
Reviewed-by: Pankaj Jangra<jangra.pankaj9@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove duplicated include.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. These pins are
essential for audio and need to be done to have working audio on the board.
Pin Mux configuration for: twl6040 audpwron gpio, McPDM, and McBSP1.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
u-boot stopped configuring 'non essential' pins recently. These pins are
essential for audio and need to be done to have working audio on the board.
Pin Mux configuration for: twl6040 audpwron gpio, McPDM, DMIC, McBSP1 and
McBSP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kteZ
-----END PGP SIGNATURE-----
Merge tag 'for_3.7-fixes-cpufreq' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.7-rc1/fixes-cpufreq
This series a couple bug fixes and a couple fixes that make this
driver support recently added OMAP-based SoCs.
The 'get_cpu_device' patch is needed due to a change in the OMAP
OMAP PM core code which enforces use of get_cpu_device() instead of
a deprecated OMAP-specific API.
The usage of plat/*.h headers breaks single zImage, so platforms are
cleaning up and/or removing plat/*.h so the driver needs to be fixed
accordingly.
This series is based on the merge of Rafael's pm-for-3.7-rc1 tag into
Linus' master branch: commit 16642a2e7b.
This patch adds a missing hwmod entry for the HDQ/1-Wire module present
in the AM3505/17 CPUs.
This restores 1-Wire support to our AM3505 boards. We think it probably
stopped working with commit 96b1b29d37
ARM: OMAP2+: HDQ1W: use omap_device
Signed-off-by: Raphael Assenat <raph@8d.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
compiler complained,
`gpmc_remove' referenced in section `.data' of arch/arm/mach-omap2/built-in.o: defined in discarded section `.exit.text' of arch/arm/mach-omap2/built-in.o
Annotate gpmc_remove function and dependents with __devexit.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
not NULL pointer. The NULL test in the return value check should
be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
not NULL pointer. The NULL test in the return value check should
be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support of
D3 clock-stop. Also changing the power_save option in sysfs kicks
off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in HD-audio
are continued cleanups and standardization for the generic auto
parser and bug fixes (HBR, device-specific fixups), in addition to
the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=uNqD
-----END PGP SIGNATURE-----
Merge tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This contains pretty many small commits covering fairly large range of
files in sound/ directory. Partly because of additional API support
and partly because of constantly developed ASoC and ARM stuff.
Some highlights:
- Introduced the helper function and documentation for exposing the
channel map via control API, as discussed in Plumbers; most of PCI
drivers are covered, will follow more drivers later
- Most of drivers have been replaced with the new PM callbacks (if
the bus is supported)
- HD-audio controller got the support of runtime PM and the support
of D3 clock-stop. Also changing the power_save option in sysfs
kicks off immediately to enable / disable the power-save mode.
- Another significant code change in HD-audio is the rewrite of
firmware loading code. Other than that, most of changes in
HD-audio are continued cleanups and standardization for the generic
auto parser and bug fixes (HBR, device-specific fixups), in
addition to the support of channel-map API.
- Addition of ASoC bindings for the compressed API, used by the
mid-x86 drivers.
- Lots of cleanups and API refreshes for ASoC codec drivers and
DaVinci.
- Conversion of OMAP to dmaengine.
- New machine driver for Wolfson Microelectronics Bells.
- New CODEC driver for Wolfson Microelectronics WM0010.
- Enhancements to the ux500 and wm2000 drivers
- A new driver for DA9055 and the support for regulator bypass mode."
Fix up various arm soc header file reorg conflicts.
* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (339 commits)
ALSA: hda - Add new codec ALC283 ALC290 support
ALSA: hda - avoid unneccesary indices on "Headphone Jack" controls
ALSA: hda - fix indices on boost volume on Conexant
ALSA: aloop - add locking to timer access
ALSA: hda - Fix hang caused by race during suspend.
sound: Remove unnecessary semicolon
ALSA: hda/realtek - Fix detection of ALC271X codec
ALSA: hda - Add inverted internal mic quirk for Lenovo IdeaPad U310
ALSA: hda - make Realtek/Sigmatel/Conexant use the generic unsol event
ALSA: hda - make a generic unsol event handler
ASoC: codecs: Add DA9055 codec driver
ASoC: eukrea-tlv320: Convert it to platform driver
ALSA: ASoC: add DT bindings for CS4271
ASoC: wm_hubs: Ensure volume updates are handled during class W startup
ASoC: wm5110: Adding missing volume update bits
ASoC: wm5110: Add OUT3R support
ASoC: wm5110: Add AEC loopback support
ASoC: wm5110: Rename EPOUT to HPOUT3
ASoC: arizona: Add more clock rates
ASoC: arizona: Add more DSP options for mixer input muxes
...
Currently, a dummy omap_device is created for the MPU sub-system so
that a device node exists for MPU DVFS. Specifically, for the
association of MPU OPPs to a device node, and so that a voltage
regulator can be mapped to a device node.
For drivers to get a handle to this device node, an OMAP-specific API
has been used. However, the kernel already has device nodes for the
CPU(s) in the system, so we can use those instead of an OMAP-specific
dummy device and then drivers (like OMAP CPUfreq) can use generic
APIs.
To use the existing CPU device nodes, modify the OPP creation and
regulator registration to use the CPU0 device node for registraion.
NOTE: this patch always uses CPU0 as the device node. On all
OMAPs today, MPU DVFS scales all CPUs together, so this will
not be a problem, but this assumption will need to be changed
if independently scalable CPUs are introduced.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
rx51_si4713_dev is referenced only from rx51_init_si4713.
So the memory for rx51_si4713_dev can be safely freed after init.
Also it references rx51_si4713_board_info which is __initdata_or_module.
fixes the below warning.
WARNING: vmlinux.o(.data+0x30958): Section mismatch in reference from the variable rx51_si4713_dev to the (unknown reference) .init.data:(unknown)
The variable rx51_si4713_dev references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Reported-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
memblock_steal tries to reserve physical memory during boot.
When the requested size is not aligned on the section size
then, the remaining memory available for lowmem becomes
unaligned on the section boundary. There is a issue with this,
which is discussed in the thread below.
https://lkml.org/lkml/2012/6/28/112
The final conclusion from the thread seems to
be align the memblock_steal calls on the SECTION boundary.
The issue comes out when LPAE is enabled, where the
section size is 2MB.
Boot tested this on OMAP5 evm with and without LPAE.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit e54adb1e79 ("ARM: OMAP: omap3evm:
cleanup revision bits") adds a new sparse[1] warning:
arch/arm/mach-omap2/board-omap3evm.c:90:4: warning: symbol 'get_omap3_evm_rev' was not declared. Should it be static?
This symbol no longer appears to be used outside this file, so mark it
static and remove the export.
...
1. https://sparse.wiki.kernel.org/index.php/Main_Page
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tony Lindgren <tony@atomide.com>
Commit 7d7e1eb (ARM: OMAP2+: Prepare for irqs.h removal) and commit ec2c082
(ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ) updated the way
interrupts for OMAP2/3 devices are defined in the HWMOD data structures to
being an index plus a fixed offset (defined by OMAP_INTC_START). The definition
of the PMU interrupts on OMAP2/3 devices is missing the OMAP_INTC_START offset
and so this is causing the allocation of PMU interrupts to fail on OMAP2/3
devices. So add the offset to fix this.
This is patch is based upon Tony's master branch for OMAP.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
After Rajendra's common-clock preparation series,
commit (a1978ef4da1 - ARM: omap: hwmod: get rid of
all omap_clk_get_by_name usage) the clkdev table need to
update with an entry for clocks used by hwmod to have
clock name same as the alias.
Without this, the clk_get() in omap_hwmod would fail.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
Merge misc patches from Andrew Morton:
"The MM tree is rather stuck while I wait to find out what the heck is
happening with sched/numa. Probably I'll need to route around all the
code which was added to -next, sigh.
So this is "everything else", or at least most of it - other small
bits are still awaiting resolutions of various kinds."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (180 commits)
lib/decompress.c add __init to decompress_method and data
kernel/resource.c: fix stack overflow in __reserve_region_with_split()
omfs: convert to use beXX_add_cpu()
taskstats: cgroupstats_user_cmd() may leak on error
aoe: update aoe-internal version number to 50
aoe: update documentation to better reflect aoe-plus-udev usage
aoe: remove unused code
aoe: make dynamic block minor numbers the default
aoe: update and specify AoE address guards and error messages
aoe: retain static block device numbers for backwards compatibility
aoe: support more AoE addresses with dynamic block device minor numbers
aoe: update documentation with new URL and VM settings reference
aoe: update copyright year in touched files
aoe: update internal version number to 49
aoe: remove unused code and add cosmetic improvements
aoe: increase net_device reference count while using it
aoe: associate frames with the AoE storage target
aoe: disallow unsupported AoE minor addresses
aoe: do revalidation steps in order
aoe: failover remote interface based on aoe_deadsecs parameter
...
Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.
Final contents described in shared tag.
Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
In case of error, the function voltdm_lookup() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function voltdm_lookup() returns NULL
not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In case of error, the function omap_device_get_by_hwmod_name()
returns ERR_PTR() not NULL pointer. The NULL test in the return
value check should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=q7ZY
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen
Warren. It's still early days on mainline support, with just the
basics working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BCp4
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates from Olof Johansson:
"Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen Warren.
It's still early days on mainline support, with just the basics
working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well."
Fix up trivial conflicts with the clk infrastructure changes.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (62 commits)
ARM: shmobile: add new __iomem annotation for new code
ARM: LPC32xx: Support GPI 28
ARM: LPC32xx: Platform update for devicetree completion of spi-pl022
ARM: LPC32xx: Board cleanup
irqchip: fill in empty Kconfig
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
These were submitted as bug fixes before v3.6 but not considered important
enough to be included in it. Some of them cross over to cleanup territory
as well, and aren't strictly bugfixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQaO1wAAoJEIwa5zzehBx38h8P/3K6wurO/3mA/Bct6vA3eJcT
9vqZ3zSEVewsF+IXIxs2F0aw2YYFUTrQ0OlLvHzYDUGB5TwYqRjbG1UR/RHiEQwD
o3dS50rq5hIXeyw46cProEK4N1vnaiI2lVH/X6B+qfABbgS094EDBc8IQU0eDABb
M0yuIMnQTfDH+JqVVO8d5m36oAwQ6ADzBRNE4l2V4jkCj4wtXFfOlMyHLBtWx2fy
jWgPA9KYB1agIJ7RuVaS4/+7XK6QJJpltinlxNaQbxYt+CofqDA1dE/r846Jm7L9
71sGo1PFhZolIsM4H70vf496hFMhzxxBupInKTERMMKZl36fwbndf3wrzGttfLRx
B7o0fLUCzoC4ePBwZ8N532h9h70UcNNebZCxN7XD66UhochqB/e9hJHWsdZkOJos
Qnsu5LiB7PfJYLlUgtvZ9W0S5D9QpjtoN9r3BMGg59F00Z2jGR54L9vGf46T1FlS
GiPLPCB+tggRAsdZXJG7qkLncPINqUXmbtgT2p1ySrI9tCzJ/lfmZ3c8dBwJtVRM
bOY+Hfwx2z7YgfVp8VtwK2wD2bOv0NRmxR+L/fTsVU5MZmS1e4TsL8figPjnakb8
ZXqZEQhv1CWmYlif3nORfg4v65/NGh4+nw1618QwsS1tBbP705bUc7zVQ9hzk4IZ
lHnQka17gG5eIaZIO0Au
=bWnd
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM soc bug fixes from Olof Johansson:
"These were submitted as bug fixes before v3.6 but not considered
important enough to be included in it. Some of them cross over to
cleanup territory as well, and aren't strictly bugfixes."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: nomadik: remove NAND_NO_READRDY use
ARM: pxa: fix return value check in pxa2xx_drv_pcmcia_probe()
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
ARM: ep93xx: Move ts72xx.h out of include/mach
ARM: ep93xx: use __iomem pointers for MMIO
ARM: msm: Fix early debug uart mapping on some memory configs
ARM: msm: io: Change the default static iomappings to be shared
ARM: msm: io: Remove 7x30 iomap region from 7x00
ARM: msm: Remove call to missing FPGA init on 8660
ARM: OMAP4: wakeupgen: remove duplicate AUXCOREBOOT* read/write
ARM: OMAP4: wakeupgen: Fix the typo in AUXCOREBOOT register save
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
...
Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree. There are also the
usual XHCI set of updates, and other various driver changes and updates.
We also are trying hard to remove the old dbg() macro, but the final
bits of that removal will be coming in through the networking tree
before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3+AACgkQMUfUDdst+ym5vwCfe93FyJyXn/RDkGz7iBemvWFd
vrwAoIxjaOa4/yWZWcgrWc5bP4aO3ssc
=jYDr
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB changes from Greg Kroah-Hartman:
"Here is the big USB pull request for 3.7-rc1
There are lots of gadget driver changes (including copying a bunch of
files into the drivers/staging/ccg/ directory so that the other gadget
drivers can be fixed up properly without breaking that driver), and we
remove the old obsolete ub.c driver from the tree.
There are also the usual XHCI set of updates, and other various driver
changes and updates. We also are trying hard to remove the old dbg()
macro, but the final bits of that removal will be coming in through
the networking tree before we can delete it for good.
All of these patches have been in the linux-next tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up several annoying - but fairly mindless - conflicts due to the
termios structure having moved into the tty device, and often clashing
with dbg -> dev_dbg conversion.
* tag 'usb-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (339 commits)
USB: ezusb: move ezusb.c from drivers/usb/serial to drivers/usb/misc
USB: uas: fix gcc warning
USB: uas: fix locking
USB: Fix race condition when removing host controllers
USB: uas: add locking
USB: uas: fix abort
USB: uas: remove aborted field, replace with status bit.
USB: uas: fix task management
USB: uas: keep track of command urbs
xhci: Intel Panther Point BEI quirk.
powerpc/usb: remove checking PHY_CLK_VALID for UTMI PHY
USB: ftdi_sio: add TIAO USB Multi-Protocol Adapter (TUMPA) support
Revert "usb : Add sysfs files to control port power."
USB: serial: remove vizzini driver
usb: host: xhci: Fix Null pointer dereferencing with 71c731a for non-x86 systems
Increase XHCI suspend timeout to 16ms
USB: ohci-at91: fix null pointer in ohci_hcd_at91_overcurrent_irq
USB: sierra_ms: don't keep unused variable
fsl/usb: Add support for USB controller version 2.4
USB: qcaux: add Pantech vendor class match
...
quite a while ago but have somehow fallen though the cracks
as most of the focus has been making things to work with
device tree. As the first patch depends on sparse IRQ
related removal of irqs.h and related header moves, these
are based on omap-cleanup-local-headers-for-v3.7 tag.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0J8j
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-board-late-v3-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
These board and platform related patches have been posted
quite a while ago but have somehow fallen though the cracks
as most of the focus has been making things to work with
device tree. As the first patch depends on sparse IRQ
related removal of irqs.h and related header moves, these
are based on omap-cleanup-local-headers-for-v3.7 tag.
* tag 'omap-devel-board-late-v3-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
On OMAP4 the i2c1 bus is dedicated for the PMIC and audio related devices.
Manufacturers can opt to use different codec than twl6040 and also can add
audio related IC to the bus (external amplifier for example on SDP4430).
Make it possible to add different set of additional devices to i2c1 bus on
OMAP4 boards.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for removal of irqs.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4460 and OMAP4470 devices have dedicated PMU interrupts and so add these
interrupts to the MPU HWMOD so we can use these for PMU events on these
devices. The PMU interrupts need to be the first interrupts in the array of
interrupts as the ARM PMU driver assumes this.
By using these dedicated interrupts we only need to enable the MPU and DEBUG
sub-systems for PMU to work. This is different to OMAP4430 that did not have
dedicated interrupts and required other power domains in addition to the DEBUG
sub-system to be enabled so we could route the PMU events to the CTI interrupts.
Hence, OMAP4460 and OMAP4470 devices can use the same list of HWMODs to create
the PMU device that is using by OMAP3.
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The original implementation of this patch was done by Ming Lei for PMU on OMAP4
[1]. Since then the PM runtime calls have been moved into the ARM PMU code and
this greatly simplifies the changes.
The another differnce since the original version, is that it is no longer
necessary to call pm_runtime_get/put during the PMU initialisation was we are no
longer accessing the hardware at this stage.
By adding runtime PM support, we can ensure that the appropriate power and clock
domains are kept on while PMU is being used.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2011-November/074153.html
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP4430 PMU events are routed to the CPU via the cross trigger interface
(CTI) because there are no dedicated interrupts. In order to route the PMU
events via the CTI IRQs, the following modules must be enabled:
l3_instr, l3_main_3, debugss
Therefore, build the arm-pmu device via these three HWMODs.
However, the CTI support for this platform still needs some work. Until
that's finished, temporarily disable the PMU on OMAP4430.
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: temporarily disabled OMAP4430 PMU support until a
better CTI interface can be implemented; added patch description note]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert OMAP2/3 devices to use HWMOD for creating a PMU device. To support PMU
on OMAP2 devices we only need to use MPU sub-system and so we can simply use
the MPU HWMOD to create the PMU device. To support PMU on OMAP3 devices, we need
to use the MPU and DEBUG sub-systems and so use these HWMODs to create the PMU
device for OMAP3.
The MPU HWMOD for OMAP2/3 devices is currently missing the PMU interrupt and so
add the PMU interrupt to the MPU HWMOD for these devices.
This change also moves the PMU code out of the mach-omap2/devices.c files into
its own pmu.c file as suggested by Kevin Hilman to de-clutter devices.c.
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed checkpatch messages; updated to apply; dropped old-style
initial filename line in header comments]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To enable PMU with runtime PM support on OMAP3 devices we need to be able to
dynamically enable and disable the debug sub-system at runtime. By adding HWMOD
data for the debug sub-system for OMAP3, we can build the PMU device using the
debug sub-system HWMOD and control this power domain using runtime PM.
Reviewed-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply; added L4-EMU address space]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The idle status of the IP blocks and clocks inside the EMU clockdomain
isn't taken into account by the PRCM hardware when deciding whether
the clockdomain is idle. Add a workaround flag in the clockdomain
code, CLKDM_MISSING_IDLE_REPORTING, to deal with this problem, and add
the code necessary to support it.
If CLKDM_MISSING_IDLE_REPORTING is set on a clockdomain, the
clockdomain will be forced active whenever an IP block inside that
clockdomain is in use, even if the clockdomain supports
hardware-supervised idle. When the kernel indicates that the last
active IP block inside the clockdomain is no longer used, the
clockdomain will be forced idle, or, if that mode is not supported in
the hardware, it will be placed into hardware-supervised idle.
This patch is an equal collaboration with Jon Hunter
<jon-hunter@ti.com>. Ming Lei <ming.lei@canonical.com>, Will Deacon
<will.deacon@arm.com>, Madhav Vij <mvij@ti.com>, Kevin Hilman
<khilman@ti.com>, Benoît Cousson <b-cousson@ti.com>, and Santosh
Shilimkar <santosh.shilimkar@ti.com> all made essential contributions
to the understanding of EMU clockdomain power management on OMAP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Madhav Vij <mvij@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Jon Hunter <jon-hunter@ti.com>
Some instances of the DMTIMER peripheral on OMAP devices have the ability
to interrupt the on-chip DSP in addition to the ARM CPU. Add a DMTIMER
attribute to indicate which timers can interrupt the DSP. By using the
omap_dm_timer_request_by_cap() API, driver will now be able to allocate
a DMTIMER that can interrupt the DSP based upon this attribute and not require
the driver to know which instance has this capability.
DMTIMERs that have the ability to interrupt the DSP on OMAP devices are as
follows ...
- OMAP1 (OMAP5912/16xx/17xx) devices - All 8 DMTIMERs
- OMAP2/3/4 devices - DMTIMERs 5-8
Please note that for OMAP3+, timer8 has the ability to interrupt the DSP and
generate a PWM output.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move the OMAP1-specific RNG device creation off to mach-omap1/devices.c,
and create a omap_device-backed registration function for OMAP2+ devices
in mach-omap2/devices.c.
As a nice side-benefit, we can also get rid of
arch/arm/plat-omap/devices.c, thanks to some recent changes from Tony.
One change from the previous behavior is that the RNG devices are now
registered unconditionally. This should allow the RNG drivers to be
loaded as modules, even if the original kernel was not built that way.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add integration data for the hardware random number generator IP block
on some OMAP SoCs. This appears to be present on at least OMAP2xxx
and OMAP3xxx SoCs, although it is not so easy to tell. It may also be
present on other OMAP2+ SoCs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Create a minimal driver out of gpmc code. Responsibilities handled by
earlier gpmc initialization is now achieved in probe.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: fixed some checkpatch messages]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Create API for platforms to adapt GPMC to HWMOD
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add gpmc hwmod and associated interconnect data
Signed-off-by: Afzal Mohammed <afzal@ti.com>
[paul@pwsan.com: added comments to the use of HWMOD_INIT_NO_RESET]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add mmu hwmod data for ipu and dsp.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: cleaned up whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add mmu hwmod data for iva and isp.
Due to compatibility an ifdef CONFIG_OMAP_IOMMU_IVA2 needs to be
propagated (previously on iommu resource info) to hwmod data in OMAP3,
so users of iommu and tidspbridge can avoid issues of two modules
managing mmu data/irqs/resets; this until tidspbridge can be migrated
to iommu framework.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: fixed some kerneldoc and whitespace; ISP MMUs not present
on AM35xx so restricted these hwmods to 34xx/36xx]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some struct omap_hwmod records belonging to PRCM IP blocks are missing
HWMOD_NO_IDLEST flags; add them.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Made *ocp2scp_usb_phy_phy_48m* as the main_clk for ocp2scp.
Since this ocp2scp module does not have any fck but does have a
single opt_clock, it is added as the main_clk for ocp2scp. Also
removed phy_48m as the optional clock since it is now made as the
main clock. By this the driver need not enable/disable phy_48m clk
separately and runtime_get/runtime_put will take care of that.
Cc: Benoît Cousson <b-cousson@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
ocp2scp_usb_phy was missing the address space data and thus
the sysconfig was not populated either.
The usb_host_hs address space was wrong.
Fix both of them and add the missing sysconfig entry.
Reported-by: Kishon Vijay Abraham <kishon@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
SAD2D stands for the die to die interface, and is used for communicating
with the optional stacked modem. This hwmod is added in preparation for
the d2d_idle move from pm34xx.c to hwmod data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: SAD2D presumably doesn't exist on non-OMAP34xx/OMAP36xx,
so only add it to the OMAP34xx/OMAP36xx lists]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For a reset sequence to complete cleanly, a module needs its
associated clocks to be enabled, otherwise the timeout check
in prcm code can print a false failure (failed to hardreset)
that occurs because the clocks aren't powered ON and the status
bit checked can't transition without them.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some IP blocks might not be using/controlling more than one
reset line, this check loosens the restriction to fully use
hwmod framework for those drivers.
E.g.: ipu has reset lines: mmu_cache, cpu0 and cpu1.
- As of now cpu1 is not used and hence (with previous check) the
IP block isn't fully enabled by hwmod code.
- Usually ipu and dsp processors configure their mmu module first
and then enable the processors, this involves:
* Deasserting mmu reset line, and enabling the module.
* Deasserting cpu0 reset line, and enabling the processor.
The ones portrayed in this example are controlled through
rproc_fw_boot in drivers/remoteproc/remoteproc_core.c
While at it, prevent _omap4_module_disable if all the hardreset
lines on an IP block are not under reset.
This will allow the driver to:
a. Deassert the reset line.
b. Enable the hwmod through runtime PM default callbacks.
c. Do its usecase.
d. Disable hwmod through runtime PM.
e. Assert the reset line.
Signed-off-by: Omar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 most modules/hwmods support module level context status. On
OMAP3 and earlier, we relied on the power domain level context status.
Identify all modules that don't support 'context_offs' by adding a
flag bit, HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT. Rest have a valid
'context_offs' populated in .prcm structure already.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: add flag bit rather than overloading .context_offs;
update changelog message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently hwmod only provides the offset for the context lose
register, and if we attempt to share the same register between two or
more hwmods, the resulting context loss counts get wrong. Thus, we
need a way to specify which bits are used for the context loss
information for each. This is accomplished by adding a new field to
the omap4 prcm struct, 'lostcontext_mask', which specifies a bit-mask
to use for filtering the register.
Mark the affected hwmods appropriately. 'l4_abe' hwmod uses the
LOSTMEM_AESSMEM bit of RM_ABE_AESS_CONTEXT register, as l4_abe doesn't
have its own dedicated register for this purpose. This register is
shared with 'aess' hwmod, thus both hwmods must also specify which
bits of the register are used for them.
This patch only adds the hwmod data, but a future patch should add
code support such that only the specified bits are read and cleared by
the context lose counter update code. If a hwmod doesn't specify
'lostcontext_mask' (default behavior), the whole contents of the
context register should be used without any filtering.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply after conversion to use flag bit for
missing module context-loss register; combined data and code patches;
dropped code change due to serial driver breakage]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, there is no support to read previous logic state
or previous memory state achieved when a power domain transitions
to RET. Instead there are module level context registers.
In order to support the powerdomain level logic/mem_off_counters
on OMAP4, instead use the previous power state achieved (RET) and
the *programmed* logic/mem RET state to derive if a powerdomain lost
logic or did not.
If the powerdomain is programmed to enter RET state and lose logic
in RET state, knowing that the powerdomain entered RET is good enough
to derive that the logic was lost as well, in such cases.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[paul@pwsan.com: removed dependency on functional power state series for now;
bumped copyright date]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The decision was made a few months ago to allow struct omap_hwmod
records and struct clk records to omit clockdomain information if the
clockdomain is not software-controllable. See for example commit
868c157df9 ("ARM: OMAP2+: hwmod: remove
prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain").
So convert an existing pr_warning() to a pr_debug() (regarding missing
clockdomains in clocks), and add a pr_debug() for missing hwmod
clockdomains. It's still useful to enable these messages for
debugging, since missing clockdomains can cause hard-to-debug problems
with power management; see for example commit
6c4a057bff ("ARM: OMAP4: clock data:
Force a DPLL clkdm/pwrdm ON before a relock").
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
We're no longer requiring struct omap_hwmod records to contain a
clockdomain. So we shouldn't return -EINVAL any more from
_omap4_wait_target_disable() or _omap4_wait_target_ready() if there's
no clockdomain defined, since that just gets passed back to the
caller. This can result in pointless warnings under the relaxed data
format.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQUWFsAAoJEBvUPslcq6VzI70P/2ECL6bunE1s53JInm7u3HFB
SM5RkOXsF8Sl+2zW0V2R8ZO9OQZC1co8e+6SmlPftv1pVXYP4wtNiFHy1MMQ5Nr7
O2ajKzAcGM1TAiJQ4A1yyfRZucOQQx7pPifACWkjagWy06JaYSUWGaea3z/g/n/U
2CGySqfyzwisiMnyZvIyxHD+cSDtERoweEEbFBKeLRlfecuBs91tIyHNbMqy7cc2
Bf+2G8m0AnrzMqhtzNAKCGJSzFEFDlr0umpLFxC+QLVFHKMJWJ7o2RwuAqf/Z9lw
AS8q2sqzypOPz7eW7z9WLqCW1YlJWhBJmLCJ1alvkebRvWRM0idlVVS3wKjHaP6q
NXF91mn21Xd9xzjXTtgigiDav0MpMuH6+FVWENanx1Rhn23GUIyRdKGMFQOeze2l
lS/vitiTDsCbXQ/EJNlDNHI2skv6AgbBbSpCsg+YivjF16DfZWhlZrFKSvQbWKfW
Mv5PnOnrpcIFNzcH8tGv9XUa61wM/HvRFbcICePAKOKy+vn2VkR/Q1XMmwHANhVf
+AMDtRNCfuspmed1pIdy4vOAcWFdXhL2jZFOBeX6rENJ2+rwJuziEuwsc1xQ8BZ5
KV9RZcg9NwvhEBiLK+K4nViRwTeeSC1OZGIEpIsJ6YOTOfWClYSnTW7In5gY1jNL
HetIvmP55Mm21G4L02D/
=UyqO
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=omEP
-----END PGP SIGNATURE-----
Merge tag 'cleanup-fixes-for-v3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ythb
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-b-for-3.7' into test_v3.6-rc6_ocb3.7_cff3.7_odaf3.7
smatch and string-wrapping cleanups for the OMAP subarch code.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.
Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
The new common clk framework includes basic definitions for mux and
divider clocks. These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP/AM33XX clk framework
has traditionally used when accessing the register to control the
mux or divisor.
To ease this transition the masks are left intact and
the width field is simply added alongside the shift and mask data.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The new common clk framework includes basic definitions for mux and
divider clocks. These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP clk framework has
traditionally used when accessing the register to control the mux or
divisor.
To ease this transition the masks are left intact and the width field is
simply added alongside the shift and mask data.
Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
While we move to Common Clk Framework (CCF), direct deferencing of struct
clk wouldn't be possible anymore. Hence get rid of all such instances
in the current clock code and use macros/helpers similar to the ones that
are provided by CCF.
While here also concatenate some strings split across multiple lines
which seem to be needed anyway.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified some compound expressions; reformatted some
messages]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>
Moving to Common clk framework for OMAP would mean we no longer use
internal lookup mechanism like omap_clk_get_by_name().
get rid of all its usage mostly from hwmod and omap_device
code.
Moving to clk_get() also means the respective platforms
need the clkdev tables updated with an entry for all clocks
used by hwmod to have clock name same as the alias.
Based on original changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
[paul@pwsan.com: removed IS_ERR_OR_NULL() conversion (rmk comment);
restricted omap_96m_alwon_fck_3630 to OMAP36xx; added missing AM35xx
clock aliases for emac_fck, emac_ick, vpfe_ick, vpfe_fck; added
aliases rng_ick and several emulation clocks]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().
For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.
The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.
This is in preparation of OMAP moving to CCF.
Based on initial changes from Mike Turquette.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
For OMAP4, the dmtimers are located in the Wake-up, ABE and Peripheral (PER)
power domains. Hence, when the dmtimer is configured to use the "timer_sys_ck"
as its functional clock the actual clock used is different depending on whether
the clock is in the Wake-up, ABE or PER domain. So when we look-up the dmtimer's
"timer_sys_ck" we need to specify the timer device name as well as clock alias
to find the right clock.
Currently, the device names for the timers have the format "omap_timer.X" where
X is the timer instance number. When using to device tree, the format of the
device name created by device-tree is different and has the format
"<reg-address>.<device-name>" (this is assuming that the device-tree "reg"
property is specified). This causes the look-up for the OMAP4 "timer_sys_ck" to
fail. To fix this add new timer clock alias for using device-tree.
Please note that adding a 2nd set of clock aliases for the same clocks to only
temporary until device-tree migration is complete. Then we can remove the legacy
aliases. Hence, I have marked the legacy aliases with a "TODO" to remove them.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add AM335x cpu0 clock entry to the corresponding clock data file. This
is useful in getting the correct mpu clock pointer to change the cpu
frequency in cpufreq driver.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[paul@pwsan.com: changed patch subject]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
These clkdev aliases should make it possible to remove the
cpu_is_omap*() calls and the omap_device*() call from
drivers/cpufreq/omap-cpufreq.c during the next merge window. Those
are interfering with multi-subarch ARM kernels.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Kevin Hilman <khilman@ti.com>
The platform device name "usbhs_tll" is added for the functional,
interface and channel clocks of the TLL module.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In commit c59b537 (ARM: OMAP2+: Simplify dmtimer clock aliases) new clock
aliases were added for OMAP2+ devices. For OMAP2420, I incorrectly set the
clock flag as CK_243X instead of CK_242X. This did not introduce a regression
as the clock flags are not checked for OMAP2 devices. This also explains why
I did not catch this when testing on OMAP2420.
Fix the clock flags for these aliases for correctness.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The file is currently called 'clock3xxx_data.c', so this comment is
out of date.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
[paul@pwsan.com: wrote changelog]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQUWFsAAoJEBvUPslcq6VzI70P/2ECL6bunE1s53JInm7u3HFB
SM5RkOXsF8Sl+2zW0V2R8ZO9OQZC1co8e+6SmlPftv1pVXYP4wtNiFHy1MMQ5Nr7
O2ajKzAcGM1TAiJQ4A1yyfRZucOQQx7pPifACWkjagWy06JaYSUWGaea3z/g/n/U
2CGySqfyzwisiMnyZvIyxHD+cSDtERoweEEbFBKeLRlfecuBs91tIyHNbMqy7cc2
Bf+2G8m0AnrzMqhtzNAKCGJSzFEFDlr0umpLFxC+QLVFHKMJWJ7o2RwuAqf/Z9lw
AS8q2sqzypOPz7eW7z9WLqCW1YlJWhBJmLCJ1alvkebRvWRM0idlVVS3wKjHaP6q
NXF91mn21Xd9xzjXTtgigiDav0MpMuH6+FVWENanx1Rhn23GUIyRdKGMFQOeze2l
lS/vitiTDsCbXQ/EJNlDNHI2skv6AgbBbSpCsg+YivjF16DfZWhlZrFKSvQbWKfW
Mv5PnOnrpcIFNzcH8tGv9XUa61wM/HvRFbcICePAKOKy+vn2VkR/Q1XMmwHANhVf
+AMDtRNCfuspmed1pIdy4vOAcWFdXhL2jZFOBeX6rENJ2+rwJuziEuwsc1xQ8BZ5
KV9RZcg9NwvhEBiLK+K4nViRwTeeSC1OZGIEpIsJ6YOTOfWClYSnTW7In5gY1jNL
HetIvmP55Mm21G4L02D/
=UyqO
-----END PGP SIGNATURE-----
Merge tag 'omap-devel-am33xx-for-v3.7' into test_v3.6-rc6_cff3.7_odaf3.7
From Paul Walmsley <paul@pwsan.com>:
AM33xx hwmod data and miscellaneous clock and hwmod fixes. AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=omEP
-----END PGP SIGNATURE-----
Merge tag 'cleanup-fixes-for-v3.7' into test_v3.6-rc6_cff3.7_odaf3.7
These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.
Remove the use of set_hs_extmute callback and let the codec driver to
handle the extmute GPIO.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To help the driver to get the correct memory range to access McPDM
registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Misc SoC-related fixes/cleanups for Samsung platforms
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
+ sync to 3.6-rc6
The TLL specific code such as channels clocks enable/disable,
initialization functions are removed from the USBHS core
driver. The hwmod of the usb tll is retrieved and omap device
build is performed to created the platform device for the
usb tll component.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the dtb targets have moved to arch/arm/boot/dts/Makefile, sweep
the platforms that have had new targets added recently and move them over.
While I was at it, I also made the dtb generation more generic, i.e. if
the platform is enabled then all dtbs for that platform will be created.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brown <davidb@codeaurora.com>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
* next/soc: (50 commits)
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
ARM: tegra30: add CPU hotplug support
ARM: tegra: clean up the common assembly macros into sleep.h
ARM: tegra: replace the CPU CAR access code by tegra_cpu_car_ops
ARM: tegra: introduce tegra_cpu_car_ops structures
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: AM33XX: clock: Add dcan clock aliases for device-tree
ARM: OMAP2+: dpll: Add missing soc_is_am33xx() check for common functions
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
ARM: OMAP3+: hwmod: Add AM33XX HWMOD data
ARM: OMAP2+: hwmod: Hook-up am33xx support in omap_hwmod framework
...
Change/remove conflict in arch/arm/mach-ux500/clock.c resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=TZVo
-----END PGP SIGNATURE-----
Merge tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
This branch contains mostly scripted changes to make omap
header files local where possible to get us closer to supporting
the ARM single zImage. After these changes mach includes are
pretty much out of the way for omap2+, but still lots of manual
work remains to sort through the remaining plat includes.
* tag 'omap-cleanup-local-headers-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_wkup_44xx.h local
ARM: OMAP2+: Make ctrl_module_pad_core_44xx.h local
ARM: OMAP2+: Make ctrl_module_core_44xx.h local
ARM: OMAP2+: Make board-rx51.h local
...
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
AM33xx hwmod data includes "mcspi.h" which has now been moved after
the platform_data move. Fix it.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
