The newly added quirk_cavium_sriov_rnm_link doesn't compile if
PCI_ATS is off. This patch adds a check for PCI_ATS.
Fixes: 21b5b8eebb ("PCI: quirk fixup for cavium invalid sriov...")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Solarflare SFC9220 apparently lacks an ACS capability, but does not
perform peer-to-peer between functions. Add a quirk so we know about this
isolation.
[bhelgaas: changelog]
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a DMA alias quirk for the Adaptec 3805, just like the 3405 quirk added
in commit d3d2ab43dd ("PCI: Add DMA alias quirk for Adaptec 3405").
Link: https://www.redhat.com/archives/vfio-users/2016-July/msg00046.html
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Similar to the AR93xx series, the AR94xx and the Qualcomm QCA988x also have
the same quirk for the Bus Reset.
Fixes: c3e59ee4e7 ("PCI: Mark Atheros AR93xx to avoid bus reset")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.14+
Add function 1 DMA alias quirk for Marvell 88SE9182.
We found this quirk reported in the same thread as other Marvell
devices, but no patch resulted:
https://bugzilla.kernel.org/show_bug.cgi?id=42679#c78
Signed-off-by: Steven Graham <sgraham@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel Sunrise Point root ports implement ACS but use dwords for the
capability and control registers, putting the control register at the wrong
offset.
Use quirks to enable and test ACS for these devices, which match the
standard functions modulo the broken control register offset.
Note that lspci assumes devices implement ACS per spec, so it shows invalid
ACS data for these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The original thought was that if a device implemented ACS, then surely
we want to use that... well, it turns out that devices can make an ACS
capability so broken that we still need to fall back to quirks.
Reverse the order of ACS enabling to give quirks first shot at it.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All of the i40e (XL710/X710) 10/20/40GbE NICs lack support for indicating
INTx is asserted via the interrupt bit in the PCI status register. The
DisINTx bit in the command register is functional, causing these devices to
be incorrectly detected as supporting INTx masking. Quirk them to properly
indicate no INTx masking support.
Device IDs copied from i40e_devids.h.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
The MIC x200 NTB forwards DMA transactions upstream using multiple alien
RIDs. These RIDs have to be added as aliases to the DMA device to allow
buffer access when the IOMMU is enabled.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
One of the quirks that adds DMA aliases logs an informational message in
dmesg. Move that to pci_add_dma_alias() so all users log the message
consistently. No functional change intended (except extra message).
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add a pci_add_dma_alias() interface to encapsulate the details of adding an
alias. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add support for the 1st gen Light Ridge controller, which is built into
these systems:
iMac12,1 2011 21.5"
iMac12,2 2011 27"
Macmini5,1 2011 i5 2.3 GHz
Macmini5,2 2011 i5 2.5 GHz
Macmini5,3 2011 i7 2.0 GHz
MacBookPro8,1 2011 13"
MacBookPro8,2 2011 15"
MacBookPro8,3 2011 17"
MacBookPro9,1 2012 15"
MacBookPro9,2 2012 13"
Light Ridge (CV82524) was the very first copper Thunderbolt controller,
introduced 2010 alongside its fiber-optic cousin Light Peak (CVL2510).
Consequently the chip suffers from some teething troubles:
- MSI is broken for hotplug signaling on the downstream bridges: The chip
just never sends an interrupt. It requests 32 MSIs for each of its six
bridges and the pcieport driver only allocates one per bridge. However
I've verified that even if 32 MSIs are allocated there's no interrupt
on hotplug. The only option is thus to disable MSI, which is also what
OS X does. Apparently all Thunderbolt chips up to revision 1 of Cactus
Ridge 4C are plagued by this issue so quirk those as well.
- The chip supports a maximum hop_count of 32, unlike its successors
which support only 12. Fixup ring_interrupt_active() to cope with
values >= 32.
- Another peculiarity is that the chip supports a maximum of 13 ports
whereas its successors support 12. However the additional port (#5)
seems to be unusable as reading its TB_CFG_PORT config space results in
TB_CFG_ERROR_INVALID_CONFIG_SPACE. Add a quirk to mark the port
disabled on the root switch, assuming that's necessary on all Macs
using this chip.
Tested-by: Lukas Wunner <lukas@wunner.de> [MacBookPro9,1]
Tested-by: William Brown <william@blackhats.net.au> [MacBookPro8,2]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
Intel Gen 1 and 2 chips use the same ID for NHI, bridges and switch. Gen 3
chips and onward use a distinct ID for the NHI.
No functional change intended.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Andreas Noever <andreas.noever@gmail.com>
* pci/aer:
PCI/AER: Log aer_inject error injections
PCI/AER: Log actual error causes in aer_inject
PCI/AER: Use dev_warn() in aer_inject
PCI/AER: Fix aer_inject error codes
* pci/enumeration:
PCI: Fix broken URL for Dell biosdevname
* pci/kconfig:
PCI: Cleanup pci/pcie/Kconfig whitespace
PCI: Include pci/hotplug Kconfig directly from pci/Kconfig
PCI: Include pci/pcie/Kconfig directly from pci/Kconfig
* pci/misc:
PCI: Add PCI_CLASS_SERIAL_USB_DEVICE definition
PCI: Add QEMU top-level IDs for (sub)vendor & device
unicore32: Remove unused HAVE_ARCH_PCI_SET_DMA_MASK definition
PCI: Consolidate PCI DMA constants and interfaces in linux/pci-dma-compat.h
PCI: Move pci_dma_* helpers to common code
frv/PCI: Remove stray pci_{alloc,free}_consistent() declaration
* pci/virtualization:
PCI: Wait for up to 1000ms after FLR reset
PCI: Support SR-IOV on any function type
* pci/vpd:
PCI: Prevent VPD access for buggy devices
PCI: Sleep rather than busy-wait for VPD access completion
PCI: Fold struct pci_vpd_pci22 into struct pci_vpd
PCI: Rename VPD symbols to remove unnecessary "pci22"
PCI: Remove struct pci_vpd_ops.release function pointer
PCI: Move pci_vpd_release() from header file to pci/access.c
PCI: Move pci_read_vpd() and pci_write_vpd() close to other VPD code
PCI: Determine actual VPD size on first access
PCI: Use bitfield instead of bool for struct pci_vpd_pci22.busy
PCI: Allow access to VPD attributes with size 0
PCI: Update VPD definitions
PCI-SIG has defined Interface FEh for Base Class 0Ch, Sub-Class 03h as "USB
Device (not host controller)". It is already being used in various USB
device controller drivers for matching, so add PCI_CLASS_SERIAL_USB_DEVICE
and use it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some devices, reading or writing VPD causes a system panic.
This can be easily reproduced by running "lspci -vvv" or
"cat /sys/bus/devices/XX../vpd".
Blacklist these devices so we don't access VPD data at all.
[bhelgaas: changelog, comment, drop pci/access.c changes]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=110681
Tested-by: Shane Seymour <shane.seymour@hpe.com>
Tested-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cavium devices matching this quirk do not perform peer-to-peer with other
functions, allowing masking out these bits as if they were unimplemented in
the ACS capability.
Signed-off-by: Manish Jaggi <mjaggi@caviumnetworks.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tirumalesh Chalamarla <tchalamarla@cavium.com>
* pci/iommu:
PCI: Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183
* pci/misc:
PCI: Limit config space size for Netronome NFP4000
PCI: Add Netronome NFP4000 PF device ID
Add function 1 DMA alias quirk for Lite-On/Plextor M6e/Marvell 88SS9183.
Signed-off-by: Tim Sander <tim@krieglstein.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Like the NFP6000, the NFP4000 as an erratum where reading/writing to PCI
config space addresses above 0x600 can cause the NFP to generate PCIe
completion timeouts.
Limit the NFP4000's PF's config space size to 0x600 bytes as is already
done for the NFP6000.
The NFP4000's VF is 0x6004 (PCI_DEVICE_ID_NETRONOME_NFP6000_VF), the same
device ID as the NFP6000's VF. Thus, its config space is already limited
by the existing use of quirk_nfp6000().
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The NFP6000 has an erratum where reading/writing to PCI config space
addresses above 0x600 can cause the NFP to generate PCIe completion
timeouts.
Limit the NFP6000's config space size to 0x600 bytes.
Signed-off-by: Jason S. McMullan <jason.mcmullan@netronome.com>
[simon: edited changelog]
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
i915 register defines are going to become type safe, so going forward
the register defines can't be used as straight numbers. Since quirks.c
needs just a few extra register defines from i915_reg.h, decouple the
two by defining the required registers locally in quirks.c. This was
already done for a few other igpu related registers.
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446672017-24497-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
* pci/aer:
PCI/AER: Clear error status registers during enumeration and restore
* pci/hotplug:
PCI: pciehp: Queue power work requests in dedicated function
* pci/misc:
PCI: Turn off Request Attributes to avoid Chelsio T5 Completion erratum
x86/PCI: Make pci_subsys_init() static
PCI: Add builtin_pci_driver() to avoid registration boilerplate
PCI: Remove unnecessary "if" statement
* pci/msi:
x86/PCI: Don't alloc pcibios-irq when MSI is enabled
PCI/MSI: Export all remapped MSIs to sysfs attributes
PCI: Disable MSI on SiS 761
* pci/resource:
sparc/PCI: Add mem64 resource parsing for root bus
PCI: Expand Enhanced Allocation BAR output
PCI: Make Enhanced Allocation bitmasks more obvious
PCI: Handle Enhanced Allocation capability for SR-IOV devices
PCI: Add support for Enhanced Allocation devices
PCI: Add Enhanced Allocation register entries
PCI: Handle IORESOURCE_PCI_FIXED when assigning resources
PCI: Handle IORESOURCE_PCI_FIXED when sizing resources
PCI: Clear IORESOURCE_UNSET when reverting to firmware-assigned address
* pci/virtualization:
PCI: Fix sriov_enable() error path for pcibios_enable_sriov() failures
PCI: Wait 1 second between disabling VFs and clearing NumVFs
PCI: Reorder pcibios_sriov_disable()
PCI: Remove VFs in reverse order if virtfn_add() fails
PCI: Remove redundant validation of SR-IOV offset/stride registers
PCI: Set SR-IOV NumVFs to zero after enumeration
PCI: Enable SR-IOV ARI Capable Hierarchy before reading TotalVFs
PCI: Don't try to restore VF BARs
The Chelsio T5 has a PCIe compliance erratum that causes Malformed TLP or
Unexpected Completion errors in some systems, which may cause device access
timeouts.
Per PCIe r3.0, sec 2.2.9, "Completion headers must supply the same values
for the Attribute as were supplied in the header of the corresponding
Request, except as explicitly allowed when IDO is used."
Instead of copying the Attributes from the Request to the Completion, the
T5 always generates Completions with zero Attributes. The receiver of a
Completion whose Attributes don't match the Request may accept it (which
itself seems non-compliant based on sec 2.3.2), or it may handle it as a
Malformed TLP or an Unexpected Completion, which will probably lead to a
device access timeout.
Work around this by disabling "Relaxed Ordering" and "No Snoop" in the Root
Port so it always generate Requests with zero Attributes.
This does affect all other devices which are downstream of that Root Port,
but these are performance optimizations that should not make a functional
difference.
Note that Configuration Space accesses are never supposed to have TLP
Attributes, so we're safe waiting till after any Configuration Space
accesses to do the Root Port "fixup".
Based on original work by Casey Leedom <leedom@chelsio.com>
[bhelgaas: changelog, comments, rename to pci_find_pcie_root_port(), rework
to use pci_upstream_bridge() and check for Root Port device type, edit
diagnostics to clarify intent and devices affected]
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
MSI is broken on SiS 761 chipset at least on PC Chips A31G board. No
interrupts are delivered once MSI is enabled for a device. This causes
hang on X11 start with a nVidia card installed (with nouveau driver).
Disable MSI completely for this chipset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
The Intel 100-series chipset now includes the integrated Ethernet as part
of a multifunction package. The Ethernet function does not include native
ACS support, but Intel confirms that the device is not capable of peer-to-
peer within the package. We can therefore quirk it to expose the
isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <john.ronciak@gmail.com>
The PCI capabilities list for Intel DH895xCC VFs (device id 0x0443) with
QuickAssist Technology is prematurely terminated in hardware.
Workaround the issue by hard-coding the known expected next capability
pointer and saving the PCIE cap into internal buffer.
Patch generated against cryptodev-2.6
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Some quirks search for a HyperTransport capability and use a hard-coded TTL
value of 48 to avoid an infinite loop.
Move the definition of PCI_FIND_CAP_TTL to pci.h and use it instead of the
hard-coded TTL values.
[bhelgaas: changelog]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI class in dev->class is a three-byte value comprising a base class,
sub-class, and interface type. PCI_CLASS_NOT_DEFINED includes the base
class and sub-class, but not the interface type, so it should be shifted to
make space for the interface. It happens that PCI_CLASS_NOT_DEFINED is
zero, so it doesn't matter in the end, but we should still use it
consistently with other class definitions.
Treat PCI_CLASS_NOT_DEFINED as a base class/sub-class value that should
appear in bits 8-23 of dev->class.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Revert aeb30016fe ("PCI: add Intel USB specific reset method").
We checked for "dev->class == PCI_CLASS_SERIAL_USB", but dev->class
contains the entire three-byte base class/sub-class/interface, while
PCI_CLASS_SERIAL_USB is only the two-byte base class/sub-class.
This error meant that we used the Intel device-specific reset on devices
with class code 0x000c03 instead of those with class code 0x0c03xx.
0x000c03 is a reserved value in the 0x00 backwards compatibility base
class and shouldn't match any devices, so I think reset_intel_generic_dev()
always failed.
I considered adding a shift, but I can't test it, so it's as likely to
break something as to fix something.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Mathias Nyman <mathias.nyman@intel.com>
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074 ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Hemant Pedanekar <hemantp@ti.com>
In the generic quirk fixup_rev1_53c810(), added by a5312e28c1 ("[PATCH]
PCI: NCR 53c810 quirk"), we assigned "class = PCI_CLASS_STORAGE_SCSI". But
PCI_CLASS_STORAGE_SCSI is only the two-byte base class/sub-class and needs
to be shifted to make space for the low-order interface byte.
Furthermore, we had a similar quirk, pci_fixup_ncr53c810(), for arch/x86,
which assigned class correctly. The arch code is linked before the PCI
core, so arch quirks run before generic quirks. Therefore, on x86, the x86
arch quirk ran first, and the generic quirk did nothing because it saw that
dev->class was already set. But on other arches, the generic quirk set the
wrong class code.
Fix the generic quirk to set the correct class code and remove the
now-unnecessary x86-specific quirk.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <matthew@wil.cx>
be6646bfba ("PCI: Prevent xHCI driver from claiming AMD Nolan USB3 DRD
device") added a quirk to override the PCI class code of the AMD Nolan
device.
Use PCI_CLASS_SERIAL_USB instead of a bare number to improve greppability.
Also add a log message about what we're doing.
No functional change except the new message.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huang Rui <ray.huang@amd.com>
CC: Jason Chang <jason.chang@amd.com>
CC: Felipe Balbi <balbi@ti.com>
Intersil/Techwell TW686[4589]-based video capture cards have an empty
(zero) class code. Fix it.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just like Haswell, Intel Atom Cherrytrail does not need the default 10ms
d3_delay imposed by the PCI specification.
Expand quirk_remove_d3_delay() to apply to Cherrytrail devices, so we can
ignore the 10ms delay before entering or exiting D3 suspend.
[bhelgaas: changelog, comment]
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
