PWM output from ecap0 uses as backlight source. Also adds low threshold
value to have a uniform divisions in brightness-levels scales.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for AM33XX and AM35XX device tree
files, in order to use the C pre-processor, making use of #define
features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
GPMC controller on AM335x-EVM has a NAND flash connected to it.
This patch updates following in am335x-evm.dts:
- adds nandflash specific pin-mux configs
- adds nand node as child of GPMC contoller, with information about
NAND flash interface, NAND partition table, ECC scheme, elm handle id.
- updates GPMC node for newer GPMC DT properties added in linux-3.10.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.
So, this patch configures the pinmux to get clkout2 on the pad.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for UART0 device nodes in all
board specific DT files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.
This patch changes UART numbering as per TRM, as uart0-5.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),
EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The TSC part allows to specify the input lines. The IIO part assumes
that it usues always the last few, that means if IIO has adc-channels
set to 2 it will use channel 6 and 7. However it might make sense to use
only 6.
This patch changes the device property (which was introduced recently
and was never in an official release) in a way that the user can specify
which of the AIN lines should be used. In Addition to this, the name is
now AINx where x is the channel number i.e. for AIN6 we would have 6.
Prior this, it always started counting at 0 which is confusing. In
addition to this, it also checks for correct step number during reading
and does not rely on proper FIFO depth.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Add support for core multifunctional device along
with its clients touchscreen and ADC.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Adding phy-mode to CPSW node for beaglebone, EVM and EVMsk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
Add CPSW and MDIO related device tree data for AM33XX.
Also enable them into board/evm dts files by providing
respective phy-id.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add gpio based volume keys device tree data to am335x-evm by adding
all the required parameters like keycode, gpios and etc.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio volume keys. In this patch, only
single named mode/state is added and these pins are configured during
pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add matrix keypad device tree data to am335x-evm by adding all
the necessary parameters like keymap, row & column gpios and etc.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add pinmux configurations for gpio matrix keypad. In this patch, only
single named mode/state is added and these pins are configured during
pinctrl driver initialization.
Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
In AM335x EVM tsl2550 ambient light sensor is connected to I2C2 bus.
Add child node inside i2c2 node with i2c slave address.
TAOS tsl2550 sensor is using a two-wire SMBus serial interface.
Reduce I2C2 clock frequency to 100kHz from 400kHz because the
maximum clock frequency of SMBus is 100kHz.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
[b-cousson@ti.com: Clean the changelog]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add temperature sensor DT data to am335x-evm.dts. In AM335x EVM
tmp275 temperature sensor is connected to I2C2 bus. So this patch
adds child node inside i2c2 node with i2c slave address. This patch
is tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add lis331dlh device tree data to am335x-evm.dts. In AM335x EVM
lis331dlh accelerometer is connected to I2C2 bus. So this patch
change the status of I2C2 node to "okay" to use I2C2 bus. Also
added all the required platform data to am335x-evm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add DT OPP table for AM33XX family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
Also adds cpu0 supply name to the corresponding dts files.
cpu0-supply name is used by cpufreq-cpu0 driver to get the
regulator pointer for voltage modifications.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
To make it consistent, convert all hex number presentation
to lower-case from all am33xx specific nodes.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Add tps65910 regulator device tree data to AM335x-EVM by adding
regulator consumers with tightened constraints and regulator-name.
TPS65910 regulator handle can be obtained by using this regulator
name.
This patch also add I2C node with I2C frequency and tps65910 PMIC
I2C slave address.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ideally in common SoC dtsi file should set all modules
to "disabled" state and it should get enabled in respective
EVM/Board dts file as per usage.
This patch sets default status of all modules to "disabled"
state in am33xx.dtsi file. Currently there are no modules
supported as part of Bone and EVM dts support, so care
to add entry "status = "okay"" while adding support for any
module.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add AM335X EVM device tree source (am335x-evm.dts) file to
use the am33xx.dtsi SoC file, along with the memory node
information.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviewed-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
