The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their vertical and next base interrupts
are not functional. Support these variants by simply disabling
the use of the vblank interrupt on these variants.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-4-linus.walleij@linaro.org
The early Integrator CLCD synthesized in the Integrator CP and
IM-PD1 FPGAs are broken: their clock dividers do not work
properly. Support disabling the clock divider and drive the
clock directly from the parent under these circumstances.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-3-linus.walleij@linaro.org
The ARM Versatile series can do RGB/BGR565 with an external
"PLD" (Programmable Logical Device). However the CLCD does not
have control bits for this, so it needs to be set into the
ordinary 16BPP mode, then the RGB/BGR565 handling of the pixel
data is handled by configuring the PLD through the external
register.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-2-linus.walleij@linaro.org
With a bit of refactoring we can contain the variant data for
the strange PL110 versions that is feature-incomplete PL110 for
the ARM Integrator/CP and somewhere inbetween PL110 and PL111
for the ARM Versatile AB and Versatile PB.
We also accomodate for the custom duct-taped RGB565/BGR565 support
in the Versatile variant.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206093540.8147-1-linus.walleij@linaro.org
The ARM reference designs "Versatile AB" and "Versatile PB"
contain panel connectors with autodetection of the connected
panel type. This adds a small driver utilizing the MFD syscon
look-up to read the autodetection register and set up the
corresponding panel appropriately.
In the source file there is a bit of elaboration of the
panel types and interfaces on these boards.
This was tested with the PL111 DRM driver on the ARM Versatile
AB with the IB2 daughterboard.
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180205192013.5349-2-linus.walleij@linaro.org
This will make it possible for userspace to know whether reading
will block, without blocking on the fd. This makes it possible to
drain all queued CRC's in blocking mode, without having to reopen
the fd.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180202142743.68527-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[mlankhorst: Use POLLIN|POLLRDNORM, based on Ville's suggestion]
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
Note that this replaces crtc_state->adjusted_mode usage with
crtc_state->mode. The latter is the correct choice since that's the
mode the user provided and it matches the plane crtc coordinates
the user also provided.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123170857.13818-2-ville.syrjala@linux.intel.com
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com> #irc
Use drm_mode_get_hv_timing() to fill out the plane clip rectangle.
No functional changes as the code already uses crtc_state->mode
to populate the clip, which is also what drm_mode_get_hv_timing()
uses.
Once everyone agrees on this we can move the clip handling into
drm_atomic_helper_check_plane_state().
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180123170857.13818-1-ville.syrjala@linux.intel.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
I'm stepping down, also handing all the drm-misc stuff to the new
team. Plan is that Sean handles 4.17, and Maarten then has fun with
4.18 as his first release.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180131102156.25634-1-daniel.vetter@ffwll.ch
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130100528.GA7154@training
The parentheses are in the wrong place here so we pass the bits per
pixel as zero.
Fixes: abbee62387 ("drm/mgag200: Added resolution and bandwidth limits for various G200e products.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125142655.GA23885@mwanda
drm_encoder_slave is the old way to write bridge drivers, for i2c
bridges only. It's deprecated, and definitely should not be used in
new drivers. This has absolutely nothing to do with the new bridge
driver infrastructure implemented by drm_bridge.
What's even strange is that arcpgu doesn't even use any of this, it
really only wants a plain normal drm_encoder. Nuke all the surplus
real estate.
v2: Actually git add after compile testing ...
v3: Clarify commit message and stop including drm_encoder_slave.h.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117141755.16933-1-daniel.vetter@ffwll.ch
Userspace can set a FB_ID on a plane without setting CRTC_ID, which
will fail with -EINVAL, but the kernel shouldn't warn about that.
Same for !FB_ID and CRTC_ID being set.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130102704.28016-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
The dw_mipi_dsi_host_transfer() must return the number of
bytes transmitted/received on success instead of 0.
Note: As the read feature is not implemented, only the
transmitted number of bytes is returned for the moment.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-3-philippe.cornu@st.com
The dcs/generic dsi read feature is not yet implemented so it
is important to warn the host_transfer() caller in case of
read operation requests.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-2-philippe.cornu@st.com
To optimize data transfers, align pitch on 128 bytes & height
on 4 bytes. This optimization is not applicable on hw without MMU.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180130104200.21602-1-philippe.cornu@st.com
In the dsi panel example, clock names in the "clock-names"
field have been swapped:
* "pclk" (peripheral clock) is <&rcc 1 CLK_F469_DSI> on stm32f4
* "ref" (dsi phy pll ref clock) is <&clk_hse> on stm32f4
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122153547.23470-1-philippe.cornu@st.com
During a non-blocking commit, it is possible to return before the
commit_tail work is queued (-ERESTARTSYS, for example).
Since a reference on the crtc commit object is obtained for the pending
vblank event when preparing the commit, the above situation will leave
us with an extra reference.
Therefore, if the commit_tail worker has not consumed the event at the
end of a commit, release it's reference.
Changes since v1:
- Also check for state->event->base.completion being set, to
handle the case where stall_checks() fails in setup_crtc_commit().
Changes since v2:
- Add a flag to drm_crtc_commit, to prevent dereferencing a freed event.
i915 may unreference the state in a worker.
Fixes: 24835e442f ("drm: reference count event->completion")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com> #v1
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117115108.29608-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Sean Paul <seanpaul@chromium.org>
We never support certain mode flags etc. Reject those early on in the
mode_config.mode_valid() hook. That allows us to remove some duplicated
checks from the connector .mode_valid() hooks, and it guarantees that
we never see those flags even from user mode as the
mode_config.mode_valid() hooks gets executed for those as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-11-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allow drivers to provide a device wide .mode_valid() hook in addition to
the already existing crtc/encoder/bridge/connector hooks. This can be
used to validate device/driver wide constraings without having to add
those to the other hooks. And since we call this hook also for user
modes later on in the modeset we don't have to worry about anything the
hook has already rejected.
I also have some further ideas for this hook. Eg. we could replace the
drm_mode_set_crtcinfo(HALVE_V) call in drm_mode_convert_umode()/etc.
with a driver specific variant via this hook. At least on i915 we would
like to pass CRTC_STEREO_DOUBLE to that function instead, and then
we could safely use the crtc_ timings in all our .mode_valid() hooks,
which would allow us to reuse those hooks for validating the
adjusted_mode during a modeset.
v2: Fix the language fails in the kernel docs (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-10-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BUILTIN, CRTC_C, CLOCK_C, and DEFULT mode types are unused. Let's
refuse to generate them or accept them from userspace either. A
cursory check didn't reveal any userspace code that would depend
on these.
v2: Recommend DRIVER instead of BUILTIN (ajax)
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115154504.14338-1-ville.syrjala@linux.intel.com
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
For some reason drm_mode_set_crtcinfo() does nothing if the mode has
the DRM_MODE_TYPE_BUILTIN flag set without the other bit from
DRM_MODE_TYPE_CRTC_C also set. I have zero idea what that is supposed
to achieve, but since we have no users for neither flag bit let's kill
this nonsense off.
v2: Fix typo in commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-7-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reject any mode with DRM_MODE_FLAG_BCAST. We have no code that even
checks for this flag hence it can't possibly do any good.
I think this maybe originated from fbdev where it was supposed to
indicate PAL/NTSC broadcast timings. I have no idea why those would
have to be identified by a flag rather than by just the timings
themselves. And then I assume it got copied into xfree86 for
fbdevhw, and later on it leaked into the randr protocol and kms uapi.
Since kms fbdev emulation never uses the corresponding fbdev flag
there should be no sane way for this to come back into kms via
userspace either.
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-5-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reject any mode with DRM_MODE_FLAG_PIXMUX. We have no code that even
checks for this flag hence it can't possibly do any good.
Looks like this flag had something to do the the controller<->ramdac
interface with some ancient S3 graphics adapters. Why someone though
it would be a good idea to expose it directly to users I don't know.
And later on it got copied into the randr protocol and kms uapi.
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-4-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Currently userspace is allowed to feed in any king of garbage in the
high bits of the mode flags/type, as are drivers when probing modes.
Reject any mode with bogus flags/type.
Hopefully this won't break any current userspace...
v2: Split the type and flags checks to separates ifs (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171115154913.23827-1-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Currently we don't sanity check the 3D stereo flags for modes filled out
by the kernel. Move the check from drm_mode_convert_umode() into
drm_mode_validate_basic() so that we get the same check going both ways.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171114183258.16976-2-ville.syrjala@linux.intel.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
We use 32bit bitmasks to track planes/crtcs/encoders/connectors.
Naturally we can only do that if the index of those objects stays
below 32. Issue a warning whenever we exceed that limit, hopefully
prompting someone to fix the problem.
For connectors the issue is a bit more complicated as they can
be created/destroyed at runtime due to MST. So the problem is no
longer a purely theoretical programmer error. As the connector
indexes are allocated via ida, we can simply limit the maximum
value the ida is allowed to hand out. The error handling is already
in place.
v2: Return an error to the caller (Harry)
v3: Print a debug message so that we know what happened (Maarten)
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125133020.23845-1-ville.syrjala@linux.intel.com
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
There's a bunch of drivers that duplicate the same function to know if a
particular format embeds an alpha component or not.
Let's create a field in the drm_format_info to avoid duplicating that logic
and looking up formats all the time.
Cc: Eric Anholt <eric@anholt.net>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9cd9951d147ff810c1f6f68d79e7983361ed6b68.1516617243.git-series.maxime.ripard@free-electrons.com
There is a difference between the panel/bridge requested pixel clock
value and the real one due to the hw platform clock preciseness (pll,
dividers...). This patch updates the adjusted_mode clock value with
the real hw clock value so then attached encoder & connector can use
it for precise timing computations.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125160101.9102-1-philippe.cornu@st.com
DP 1.4 spec adds a TPS4 training pattern sequence required for
HBR3. This patch adds the corresponding bit definitions in
MAX_DOWNSPREAD register and TRAINING_PATTERN_SET and
inline functions to check if this bit is set and for selecting
a proper TRAINING_PATTERN_MASK that changed to 0x7 on
DP spec 1.4
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516660991-20697-2-git-send-email-manasi.d.navare@intel.com
Change reservation_object_get_fences_rcu to make the exclusive fence
pointer optional.
If not specified the exclusive fence is put into the fence array as
well.
This is helpful for a couple of cases where we need all fences in a
single array.
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110125341.3618-1-christian.koenig@amd.com
