Use a different markup for the ERR_PTR, as %FOO doesn't work
if there are parenthesis. So, use, instead:
``ERR_PTR(-EINVAL)``
This fixes the following warning:
./drivers/gpio/gpiolib.c:139: WARNING: Inline literal start-string without end-string.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/51197e3568f073e22c280f0584bfa20b44436708.1584456635.git.mchehab+huawei@kernel.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GG.0 and GG.1 GPIOs serve as CLKREQ and RST pins, respectively, for
PCIe controller 5 on Tegra194. When this controller is configured in
endpoint mode, these pins need to be used as GPIOs by the PCIe endpoint
driver. Typically the mode programming of these pins (GPIO vs. SFIO) is
performed by early boot firmware to ensure that the configuration is
consistent.
However, the GG.0 and GG.1 pins are part of a special power partition
that is not enabled during early boot, and hence the early boot firmware
cannot program these pins to be GPIOs (they are SFIO by default). Adding
them as pin ranges for the pin controller allows the pin controller to
be involved when these pins are requested as GPIOs and allows the proper
programming to take place.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-4-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for Tegra SoC generations to specify a list of pin ranges
that map GPIOs to ranges of pins in the pin controller.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-3-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Wake gpiochip_generic_request() call into the pinctrl helpers only if a
GPIO controller had any pin-ranges assigned to it. This allows a driver
to unconditionally use this helper if it supports multiple devices of
which only a subset have pin-ranges assigned to them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200319122737.3063291-2-thierry.reding@gmail.com
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default handling of the gpio-line-names property by the
gpiolib-of implementation does not work with the multiple
gpiochip banks per device structure used by the gpio-brcmstb
driver.
This commit adds driver level support for the device tree
property so that GPIO lines can be assigned friendly names.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Link: https://lore.kernel.org/r/1583780521-45702-1-git-send-email-opendmb@gmail.com
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since name == NULL can't ever match, move the check out of
IRQ-disabled region.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
DSET/DCLR registers only works on output pins. Add corresponding
BGPIOF_NO_SET_ON_INPUT flag to bgpio_init call to fix direction_out
behavior.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Some gpio controllers ignores pin value writing when that pin is
configured as input mode. As a result, bgpio_dir_out should set
pin to output before configuring pin values or gpio pin values
can't be set up properly.
Introduce two variants of bgpio_dir_out: bgpio_dir_out_val_first
and bgpio_dir_out_dir_first, and assign direction_output according
to a new flag: BGPIOF_NO_SET_ON_INPUT.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
platform_get_irq() will generate an error message if the requested irq
is not present
mvebu-gpio f1010140.gpio: IRQ index 3 not found
use platform_get_irq_optional() to avoid the error message being
generated.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Existing (irq < 0) condition is always false because adev->irq has unsigned
type and contains 0 in case of failed irq_of_parse_and_map(). Up to now all
the mapping errors were silently ignored.
Seems that repairing this check would be backwards-incompatible and might
break the probe() for the implementations without IRQ support. Therefore
warn the user instead.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
These two devres functions devm_gpiochip_[add|remove]()
were in the wrong file. They should be in gpiolib-devres.c
not gpiolib.c.
Link: https://lore.kernel.org/r/20200313081522.35143-1-linus.walleij@linaro.org
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit a522f1d0c3.
With cpu_pm handling fixed for omaps, and with gpio-omap now returning
notify error on pending interrupts, we can drop the old workaround for
seeing if there may be pending edge interrupts.
Depends-on: ARM: OMAP2+: Handle errors for cpu_pm
Depends-on: gpio: omap: Block idle on pending gpio interrupts
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200304225433.37336-4-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the SoC cpuidle handling fixed for cpu_pm, we can now start to
return NOTIFY_BAD if there there are pending gpio interrupts.
This way the deeper SoC idle states can get blocked, and gpio latency
is improved in some cases. Note that this will not help with the
latency if the SoC has already entered a deeper idle state.
Note that this patch depends on cpu_pm properly handling the errors
returned by notifiers. For omap variants, this is fixed with patch
"ARM: OMAP2+: Handle errors for cpu_pm".
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200304225433.37336-3-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- replace z zero-length array with flexible-array member in gpio-uniphier
- make naming of variables consistent in uapi line event code
- fix the behavior of line watch/unwatch ioctl()
-----BEGIN PGP SIGNATURE-----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=ASHn
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.7-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.7 part 2
- replace z zero-length array with flexible-array member in gpio-uniphier
- make naming of variables consistent in uapi line event code
- fix the behavior of line watch/unwatch ioctl()
The optimization to check for requested lines actually optimized for the
uncomon error case, where one of the GPIO lines is still in use.
Hence the error message must be printed when the loop is terminated
early, not when it went through all available GPIO lines.
Fixes: 869233f813 ("gpiolib: Optimize gpiochip_remove() when check for requested line")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200302082448.11795-1-geert+renesas@glider.be
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When operating on the bits of watched_lines bitmap, we're using
desc_to_gpio() which returns the GPIO number from the global numberspace.
This leads to all sorts of memory corruptions and invalid behavior. We
should switch to using gpio_chip_hwgpio() instead.
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Reported-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Kent Gibson <warthog618@gmail.com>
Fix the field having a bit cleared by the unwatch ioctl().
Fixes: 51c1064e82 ("gpiolib: add new ioctl() for monitoring changes in line info")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename 'event' to 'ge' to be consistent with other use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertenly introduced[3] to the codebase from now on.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Here are the following optimizations have been done:
- break the loop after first found requested line
- due to above, drop redundant boolean variable
- replace open coded variant of gpiochip_is_requested()
- due to above, drop redundant pointer to struct gpio_desc
- use 'unsigned int' instead of 'unsigned' for loop counter
Note, pointer to struct gpio_chip followed by pointer to struct gpio_device
is still valid, back link is not.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200225114725.839-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO hogs are configured at GPIO controller initialization time,
adding/removing GPIO hogs in DT overlays does not work.
Add support for GPIO hogs described in DT overlays by registering an OF
reconfiguration notifier, to handle the addition and removal of GPIO hog
subnodes to/from a GPIO controller device node.
Note that when a GPIO hog device node is being removed, its "gpios"
properties is no longer available, so we have to keep track of which
node a hog belongs to, which is done by adding a pointer to the hog's
device node to struct gpio_desc.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200220130149.26283-3-geert+renesas@glider.be
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Extract the code to add all GPIO hogs of a gpio-hog node into its own
function, so it can be reused.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200220130149.26283-2-geert+renesas@glider.be
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The existing use of ktime_get_real_ns() in the timestamps from
the GPIO events is dubious.
We have had several discussions about this timestamp, and it is
unclear whether userspace has ever taken into account that a
timestamp from ktime_get_real_ns() can actually move backwards
in time relative the previous timetamp, and userspace is more
likely to expect a monotonic counter.
Background:
https://lore.kernel.org/linux-gpio/CAK8P3a1Skvm48sje8FNDPLYqyz9Lf8q0qX1QETWtyZTxuX4k1g@mail.gmail.com/https://marc.info/?l=linux-gpio&m=151661955709074&w=2
The change is ABI incompatible, but incompatible in a way that
is IMO more likely to fix future bugs rather than break current
userspace. To the best of my knowledge all userspace expects
a monotonic timestamp and users are just lucky that they very
seldom move backwards in time.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whenever retrieving a descriptor from a gpiochip: use the provided
helper which checks for errors.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200219094702.6463-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All the irq related callbacks are called with the (raw) spinlock
desc->lock being held. So the lock here must be raw as well. Also irqs
were already disabled by the caller for the irq chip callbacks, so the
non-irq variants of spin_lock must be used there.
Fixes: be8c8facc7 ("gpio: new driver to work with a 8x12 siox")
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20200211135121.15752-1-uwe@kleine-koenig.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The indentation is wrong in gpio_mockup_apply_pull(). This patch makes
the code more readable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200210155059.29609-1-brgl@bgdev.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently there is no way for user-space to be informed about changes
in status of GPIO lines e.g. when someone else requests the line or its
config changes. We can only periodically re-read the line-info. This
is fine for simple one-off user-space tools, but any daemon that provides
a centralized access to GPIO chips would benefit hugely from an event
driven line info synchronization.
This patch adds a new ioctl() that allows user-space processes to reuse
the file descriptor associated with the character device for watching
any changes in line properties. Every such event contains the updated
line information.
Currently the events are generated on three types of status changes: when
a line is requested, when it's released and when its config is changed.
The first two are self-explanatory. For the third one: this will only
happen when another user-space process calls the new SET_CONFIG ioctl()
as any changes that can happen from within the kernel (i.e.
set_transitory() or set_debounce()) are of no interest to user-space.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
We'll soon be filling out the gpioline_info structure in multiple
places. Add a separate function that given a gpio_desc sets all relevant
fields.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently if the line-event kfifo is full, we just silently drop any new
events. Add a ratelimited debug message so that we at least have some
trace in the kernel log of event overflow.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The read_lock mutex is supposed to prevent collisions between reading
and writing to the line event kfifo but it's actually only taken when
the events are being read from it.
Drop the mutex entirely and reuse the spinlock made available to us in
the waitqueue struct. Take the lock whenever the fifo is modified or
inspected. Drop the call to kfifo_to_user() and instead first extract
the new element from kfifo when the lock is taken and only then pass
it on to the user after the spinlock is released.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Typcasting "irq_state" leads to the below static checker warning:
The fix is to declare "irq_state" as unsigned long instead of u32.
drivers/gpio/gpio-sifive.c:97 sifive_gpio_irq_enable()
warn: passing casted pointer '&chip->irq_state' to
'assign_bit()' 32 vs 64.
Fixes: 96868dce64 ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Link: https://lore.kernel.org/r/1580189061-14091-1-git-send-email-yash.shah@sifive.com
Reviewed-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Care is taken with "index", however with the current version
the actual xgpio_writereg is using index for data but
xgpio_regoffset(chip, i) for the offset. And since i is already
incremented it is incorrect. This patch fixes it so that index
is used for the offset too.
Cc: stable@vger.kernel.org
Signed-off-by: Paul Thomas <pthomas8589@gmail.com>
Link: https://lore.kernel.org/r/20200125221410.8022-1-pthomas8589@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove unnecessary argument when setting PIN_CONFIG_BIAS_DISABLE. No
argument is expected by pinctrl, so removing it should be harmless.
Fixes: 2148ad7790 ("gpiolib: add support for disabling line bias")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Commit d90f36851d ("gpiolib: have a single place of calling
set_config()") introduced a regression where we don't pass the right
variable as argument to the set_config() callback of gpio driver from
gpio_set_config(). After reverting two additional patches that came
on top of it - this addresses the issue by changing the type of the last
argument of gpio_do_set_config() to unsigned long and making sure the
packed config variable is actually used in gpio_set_config().
Fixes: d90f36851d ("gpiolib: have a single place of calling set_config()")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit e5e42ad224.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit d18fddff06.
This patch came on top of another patch that introduced a regression.
Revert it before addressing the culprit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
The check with register value and mask should be & rather than &&.
While at it, also use "unsigned int" for value variable because
regmap_read() takes unsigned int *val argument.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The .set callback should just set output value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Not all platforms use those. Let's use
platform_get_irq_byname_optional() instead platform_get_irq_byname() so
that we avoid a useless warning:
[ 1.359455] pxa-gpio d4019000.gpio: IRQ gpio0 not found
[ 1.359583] pxa-gpio d4019000.gpio: IRQ gpio1 not found
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
- New Device Support
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
- New Functionality
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
- Fix-ups
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers; madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
- Bug Fixes
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEdrbJNaO+IJqU8IdIUa+KL4f8d2EFAl44Ga0ACgkQUa+KL4f8
d2HRJg//VdigHgOTX/eJggI67n36kTgho+VzwRwLuSedDBFIkh5S8NWO7bFyf1Y4
Qn+MybJtCvPQeUVmqO6cUi0/VqXgwW4mUe5L6oQKIsPYzfmhuc/XF+DA2S8ulOBj
CckAM15i4WARCtNtFH12EaGGekLPAkik9nZE5EH7vS89TUxLMKbir72U+qFju6mu
o2F8B7QbDe2jxaooxZ11zPjECwJfzgdXe+FipmogL1itLT+1phpirlttY4R5/4LV
t3jKb3GI5xN+YWqyXHFF1EKtQEHTkYyKcby2It+8ksYAKiueY0hAuX7+pt1KXWjb
ReM/hYH5dqjJSz6MjajrInHlpAf8iqtzNdXznSm/hQ9X+YHpaqmdYBt9bTg3pbR/
z5F0q32e716K/XcJIv2igizT2EZDZIb2AG9oh0D93Z10tPgTpp0CTkcSsSw4CpnP
MM60B2RN6RI/1MVK1eWRfWVSLbopsForetlnwXhTxY0Zr/7Hd+l+2ndz8IJE+vya
86jq9yXv7kndwcKNIuUy5jIE2XV9JIbjwwDd4a8tbQgOMkSWHuV3pN+qnT6+/kRh
TS/LFI49rjJauB85XdqhZc2+i0Eo78ctIdxQebKNZe6wz+r5Y5NTMMCZ5TjScxJX
aSKRepOEtSbnKloUi5HZ71zfX/waTxzgyodkF7UJk3eEtzlDF8o=
=t4+B
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we
got rid of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips
along with the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much
improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt
map is provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML
DT bindings schema. (A first user of this.)
-----BEGIN PGP SIGNATURE-----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=PnK5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
Core changes:
- Document the usecases for the kernelspace vs userspace
handling of GPIOs.
- Handle MSI (message signalled interrupts) properly in the
core hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor
array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain
with GPIOLIB_IRQCHIP on top of the revert of the previous
buggy switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes.
-----BEGIN PGP SIGNATURE-----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=3Glg
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
